Complete Panel (59-1/2" H)
Contents
1. INSTALLATION MANUAL PRIVACY WALL amp DECORATIVE 3 HIGH PANEL KIT XIX Ps VA VA PAA PZA Yardistry Mount Forest ON Canada NOG 2L1 Toll Free Customer Support 1 888 509 4382 info yardistrystructures com www yardistrystructures com Revised 04 19 2012 1 IMPORTANT SAFETY NOTICE Yardistry components are intended for privacy decorative and ornamental use only Product is NOT INTENDED for the following A safety barrier to prevent unsupervised access to pools hot tubs spas or ponds Safety railings for elevated platforms or decks As load bearing support for a building structure heavy objects or swings Used in structures that trap wind rain or snow that would create extra load on the product Permanent structures may require a building permit As the purchaser and or installer of this product you are advised to consult local planning zoning and building inspection departments for guidance on applicable building codes and or zoning requirements Wood is NOT flame retardant and will burn Grills fire pits and chimneys are a fire hazard if placed too close to a Yardistry structure Consult user s manual of the grill fire pit or chimney for safe distances from combustible materials During installation follow all safety warnings provided with your tools and use OHSA approved safety glasses Some structures may require two or more people to2. by arrows in the direction of the arrow Fig 2 R Top and Bottom Rails will overhang 1 4 on either side of panel 2x TOP amp BOTTOM RAIL 78 1 2 24x G 8 2 1 4 WOOD SCREWS STEP 3 INSTALLING PANEL CLIPS a Pa 1 Postition Panel Clips in locations indicated in Figures 1 and 1A Orient Panel Clips according to whether you want them to be visible or not i e facing inside or facing the outside 2 Panel Clips should be placed in the centre of the post or the leading edge of the clip should be 1 3 8 or 3 5cm away from the side of the post as shown in Fig 2 3 With Panel Clips in place mark screw holes with a pencil and pre drill holes with a 1 8 drill bit Not provided 4 Secure Panel Clips in locations indicated in figure 1 and 1A with S7 8 x 1 1 2 wood screws Fig 1A 13 8 aul 3 5em Top View J H Pre drill holes and secure with S7 8 x 1 1 2 Wood Screws Fig 1 B E a 40 1016 101 6 cm p 4 E E 10 10 25 3 cm 25 3 cm Ly Y Note these clip heights are designed for a 4 ground t clearance For ground clearance less than 4 subtract equal number from clip heights for appropriate measurement 6X PANEL CLIPS 12x 8 X 1 1 2 WOOD SCREW STEP 4 INSTALLING WALL INTO fi PE FLAT ROOF PERGOLA ASE
3. 1 With the help of an adult place the Wall on Panel Clips as shown Fig 1 allowing a 4 gap between the bottom of the post and the bottom edge of U 3 the bottom rail on the panel assembly 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the Wall to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of arrows Fig 1 bY Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw Fig 1 4 4 10 2cm 6x G 10 x 1 PAN SCREWS STEP 4 INSTALLING WALL INTO fi PE ARCHED PERGOLA Q 4 1 With the help of an adult place the Wall on Panel Clips as shown Fig 1 allowing a 4 gap between the bottom of the post and the bottom edge of U 3 the bottom rail on the panel assembly 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the Wall to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of arrows Fig 1 X xX Heere ECECELET TTTITTTTT mamama COCOCECEE EEETECrt 6x G 10 x 1 PAN SCREWS STEP 4 INSTALLING WALL INTO FENCE fi Q PE 1 With the help of an adult place the Wall on Panel Clips a
4. EMBLE PANELS 1 Remove the upper metal connectors on both sides of P_2 Two High_Panel Reattach the metal connectors to P_2 by securing the bottom two holes of the metal connectors to the top two holes on P_2 so that the metal connectors stick out from the top Slide P_1 One High_Topper between the two protruding metal connectors on the top of P_2 Attach the metal connectors to P_1 Fig 1A Ensure Panels are oriented correctly Fig 1B 2 Secure panels with a S4 2 1 4 Wood Screw the location indicated by the large arrow in the direction of the arrow 3 Repeat until four panel assemblies are created amp 8 iN EEE oo or Fig 1B Filler Strips on Bottom of Panel amp 8 Fig 1A 4X ea ONE HIGH _TOPPER 4x G 8 2 1 4 WOOD SCREWS 4x F3 TWO HIGH _ PANEL STEP 2 ASSEMBLE WALL a 1 Assemble panels together in configuration shown Fig 1 Insert male connector into female Slide down until flush with adjacent panel as shown Fig 1A 2 Secure Panels with S4 2 1 4 screws provided in pre drilled holes as indicated by arrows in the direction of the arrow Fig 1 3 Secure R Top and Bottom Rails to Panel Assembly with S4 2 1 4 Wood Screws locations indicated
5. install safely Check for underground utilities before digging or driving stakes into the ground General Information Wood components are manufactured with Cedar C Lanceolata which is protected with factory applied water based stain Knots small checks cracks and weathering are naturally occurring and do not affect the strength of the product Annual application of a water based water repellent sealant or stain will help reduce weathering and checks Warranty Yardistry products are backed by a 5 year limited lifetime warranty from the date of original retail purchase for manufacturing defects and if installed as per manufacturer s installation instructions Patents Pending Tools Required Tape Measure 2 Phillips or Robertson Safety Glasses Carpenters Level Bits or Screwdriver Adult Helpers 1 8 Drill Bit Carpenters Square Standard or Cordless aRenel Drill 8 Step Ladder Keys To Assemble Success This identifies information that requires special Check that set or assembly is properly level Use attention Improper assembly could lead to an before proceeding Level unsafe or dangerous condition Use Use Where this is shown 2 or 3 Pre drill 1 8 amp 3 16 Bit eA Help Help Pre drill a pilot hole people are required to safely i complete the step To avoid pr zY before fastening screw injury or damage to the A 6 or lag to prevent assembly make sure to get help splitting of wood Tigh
6. s shown Fig 1 allowing a 4 gap between the bottom of the post and the bottom edge of the bottom rail on the panel assembly 2 With a 1 8 drill bit predrill holes as shown in figure 2 3 Fasten the Wall to the post and Panel Clips with a S5 1 Pan Head Screw provided in location of arrows Fig 1 N Fig 2 Predrill Holes and Fasten with S5 1 Pan Head Screw Fig 1 LOCC LITT TI TT OONN 6x G 10 x 1 PAN SCREWS 10
7. ten Measure Check that assembly is square Square Distance i i Assembly before tightening bolts This indicates time to tighten bolts but u ina tape not too tight Do not crush the wood Sea measuring KAPELO ASSUTA This may create splinters and cause proper location structural damage Shown using 4 high privacy panel YM12505 12x12 Arched Roof Pergola 12x12 Complete Pergola Room YM11507 MATERIAL LIST 4 One High X Topper or 4 One High Lattice Topper or 4 One High Faux Glass Topper P_2 4 Two High Lattice Panel or 4 Two High X Panel R 2 Top and Bottom Rail Note Wall assembly in this instruction is shown as a 2 High Lattice Panel with a 1 High X Topper Depending on kit purchased images may not be accurate Please see front cover for what your final set up should look like You may also refer to page 3 for what assemblies may look like inside the different units 10 x 1 Pan Head Screw a 8 x 1 1 2 Wood Screw 6 Panel Clips Privacy amp Decorative Panel Kits 3 High Privacy Lattice X Panel YM11538 3 High Privacy Lattice Panel YM11541 3 High Decorative X Panel YM11543 3 High Lattice with Faux Glass Panel YM11553 STEP 1 ASS
Download Pdf Manuals
Related Search