LuminTrail LED Bicycle Light User Manual Model: TB
Contents
1. Please use with caution 1 Charging the battery pack The battery pack is shipped half charged You need to fully charge it before first use Connect the battery to the charger the charger LED will turn Green Plug the charger into the power outlet the charger LED will turn Red indicating that the battery is charging A full charge from empty will take approximately 4 hours Once fully charged the LED will turn Green Unplug the charger and disconnect the battery 2 Handle Bar Mounting Insert the O ring into the hook on the front of the light head You must stretch the O ring slightly which makes it thinner and then it slips into place easily A A B Place the light head on the handlebars and stretch the O ring around the bottom of the handle bar Clip it onto the hook at the rear of the light head B Various O ring sizes are provided Use the one which provides the best fit depending on the size of your handle bars C C D Find the most suitable place for mounting the battery If you have a long enough stem this is the best place to put it otherwise you can mount it to your bike frame D or handlebars Opposite side to the light Estimate how much cable length you will require and then fold up the excess cable into battery pouch E Wrap the Velcro strap around the stem frame handle bars at the same time stuffing the excess cable into the pouch Plug light cable into2. 585g with battery pack Package Includes light head battery pack charger helmet mount extension cable O rings
3. 75 Blue 75 30 Red 30 5 Flashing Red lt 5 6 Battery Storage Disconnect the battery pack from the light head when not using Store the battery pack fully charged and re charge it before using the lighting system again If not used for an extended period of time please store the battery pack in a cool dry place to avoid excessive discharge 7 Troubleshooting Failure Caused Solution No light Battery is over discharged Charge the battery Battery is not plugged in correctly Make sure all parts are firmly connected Running time too short Battery is not fully charged Charge the battery New battery Charge the battery Very old battery Replace the battery Cold temperature Keep the battery warm Defective charger Replace the charger Flicker Cables not secured Make sure all parts are firmly connected 8 Technical Data LED 3 CREE XML LED lifespan above 50 000 hours Max output 3000 lumens Lens High transparent acrylic lens Modes 3 level adjustable brightness flashing and over heat protection functions Output levels Max 3000 lumens Medium 1450 lumens Low 650 lumens Runtime Max 3 hours Medium 6 hours Low 12 hours Power indicator 3 color 4 modes LED indicator to display battery capacity Battery capacity Voltage 16 8V 4X26650 water resistant design Charge time 4 hours Shell material 6061 T6 Aluminum alloy Waterproof grade IPX6 Weight 130g without battery pack
4. LuminTrail LED Bicycle Light User Manual Model TB 3000 Please Read Before Use Please read this user manual to completely familiarize you with this product Make sure you understand all functions before hitting the trails Cycling in the dark is inherently dangerous Always make sure the light is firmly secured and the battery is fully charged before you go for a ride Like all other electronic devices the light can fail at any unexpected time It is advised to always keep a backup light and battery pack with you whenever you go on an extended ride Please note that your LuminTrail light is very bright never aim it directly at any oncoming motorists cyclists Your LuminTrail bicycle light is equipped with a high capacity Lithium ion battery pack Please completely charge the battery before first use of the light While the battery pack is double protected you should always observe the following While charging the batteries never leave it unattended for a long time Only use the LuminTrail charger to charge the batteries Using other chargers to charge LuminTrail batteries may cause battery failure and or other serious damage Your LuminTrail bicycle light uses high power LEDs which especially in turbo high mode generate a significant amount of heat The aluminum light head is designed to draw most of the excess heat away The light head may get extremely hot during this process if sufficient air flow is not provided
5. the battery cable F E F G 3 Helmet mounting Attach the helmet bracket to your helmet by feeding the Velcro straps through your helmets air vents You can cut the straps shorter if needed G Insert the O ring into the hook on the front of the light head Place the light head on the helmet mount bracket and stretch the O ring around the underneath Clip it onto the clip at the rear of the light head Guide the cable through one of your helmet straps or Velcro it to the back of your helmet in order to ensure that the cable doesn t snag on a low hanging branch or dangle down in front of your face while you are riding Place the battery in a convenient location Some suggestions are pocket attached to hydration pack or inside hydration pack Plug the light cable into the battery cable F 4 Operating LuminTrail TB 3000 light The switch is illuminated while plugged in which makes it easy to locate in the dark The light starts in the OFF mode Push the switch button for High Medium Low Push and hold the switch button for two seconds from any setting to turn the light OFF Push and hold the switch button for two seconds from off to enter into the FLASH mode 5 Battery Level Indicator The LuminTrail TB 3000 comes with a 4 stage power meter As the battery depletes the backlit switch button will change color from Green Blue Red Flashing Red Green 100
Download Pdf Manuals
Related Search