RACK-232 CHASSIS USER`S MANUAL
Contents
1. EXPLODED DIAGRAM APPENDIX B 162. a a So POWER LED GREEN HDD LED RED 12345678 Pin LP 01 Panel BZ1 BUZZER D1 POWER LED D2 System HDD LED SW1 RST system reset button CN1 FUNCTION SPEAKER SPEAKER RESET 2 O O O D D O O O 2 3 Rear Panel of RACK 232 AC INPUT 2 4 Removing the chassis cover The cover is mounted by five screws on the top of the chassis remove them and slide the cover to the rear of the chassis Figure below shows how to remove the chassis cover 2 5 Backplane Installation Figure below illustrates how to install the backplanes on the RACK 232 Please plug the connector of ACE 890 to the Backplane IP 2SD VER 2 1 PCI 2SD VER 1 3 ACE 890 POWER SUPPLY IP 52 Ode 2 6 Disk Drives Installation 1 Open the upper disk drive cover 2 Mount the drive rails on the side of FDD 3 Attach the FDD to the bracket with four screws and connect FDD cable 8 power cable to the FDD 4 Directly fix the 3 5 HDD with four screws into chassis and connect a 40 pin flat cable amp power cable to it Ez gt 12 2 7 Power Supply Installation 2 8 Fan Installation 14 APPENDIX A PASSIVE BACKPLANES v00000000000000000 99 5 223 1 253 5 261 IP 2SD VER 2 1 MODEL PCI 2SD VER 1 3 CELILIILIILZLLIZLIZLZIZLZZLZZZ ZT CLIZIIIIZIIZZIIZIZZ 161 5 255 5 261 PCI 2SD ver 1 3 15
3. CD ROM One 3 5 FDD Drive and One 3 5 HDD or Two 2 5 HDD drives spaces Cooling Fan Triple Ball bearing fans Indicator Two LEDs to monitor the status of HDD and Power Supply Dimension 483 x 486 x 44 WxDxH VO Port One USB Port Type A Reset Buttom Yes Buzzer Yes Passive Backplanes Optional PCI 2SD 2 slot ISA PCI bus Backplane VER 1 3 IP 2SD 2 slot PCISA bus Backplane VER 2 1 Power Supply Standard equipped power supply for the RACK 232 is ACE 890A Optional ACE 890P 70V 132VDC input power supply ACE 890T 36V 72VDC input power supply ACE 890C 18V 36VDC input power supply ACE 890V 9V 16VDC input power supply Working Environment Operating Temperature 0 50 C Relative Humidity 5 95 Relative Vibration 5 17Hz 0 1 double amplitude displacement 17 640Hz 1 5G acceleration peak to peak Shock 10G acceleration peak to peak Safety approval meet CE FCC Cooling Fan Triple rear ball bearing cooling fans Drive Capacity One 5 25 CD ROM one3 5 FDD and one 3 5 HDD drive spaces or two 2 5 HDD Drives spaces 1 3 Dimensions UNIT mm Chapter 2 Installation Procedure The following set up procedures are provided to assist you in installing the system unit please follow the steps below 2 1 Front Panel of RACK 232 4 e LR A a HDDLED POWER LE D Q Pr D uy 2 2 LP 01 Control Panel of RACK 232 RESET SWITCH BUZZER
4. RACK 232 CHASSIS USER S MANUAL Copyright Notice This document and product is copyrighted January 2000 by ICP Electronics Inc All rights are reserved No part of this manual may be reproduced copied or translated without prior notice to ICP Electronics Inc The information provided in this document is for reference only We do not assume any responsibility arising out of the application of the products This manual is subject to change without any notice RACK 232 ICP are trademark of ICP Electronics Inc Table of Contents Chapter 1 Product Information 1 1 General Information 1 2 Product Specifications 1 3 Dimensions Chapter 2 System Setup 2 1 Front Panel of RACK 232 2 2 LP 01 Control Panel of RACK 232 2 3 Rear Panel of RACK 232 2 4 Removing the chassis cover 2 5 Backplane Installation 2 6 Disk Drives Installation 2 7 Power Supply Installation 2 8 Fan Installation Appendix A Passive Backplane Appendix B Exploded Diagram Chapter 1 Product Information 1 1 General Information RACK 230A IPC chassis is a rugged PC AT compatible computer designed for the factory floor and other Industrial harsh environment RACK 230A features 2 slots Passive Backplanes and high reliability ACE 890 series power supply The chassis can easily be installed on 19 Rack or Desktop with the supplied brackets 1 2 Product Specifications General specification Construction Heavy duty Consideration Disk Driver One 5 25
Download Pdf Manuals
Related Search