Intelligent Intercom System
Contents
1. Note The double button line extended panel should match double button line door station the single button line extended panel should match single button line door station For example the EP11 Dx should be connected to MR11 Dx 5 Basic Connection lt P to next floo f Distribu to monitors A a a a a a 2 E La D a a a a 2 2 Distributor GX 7P C3 150 A a a a 8 v 6 ooooood T JWB OUT JWP JWV OUT p2 lool El MD2 MD1 P MA1 P P VG VD Oo m El m O El E a E a E E Exit button 12V 300mA _ SQ Power supply 0 0000000000000 00000000000000 ooooo0o0o00000000 teg Monitor Monitor 6 Door Lock Connections 1 Internal Power Supply Mode Use the power of the system to supply for the electronic lock so that the lock can be connected to the door station directly without an additional power supply for the electronic lock Note that the door station can only output 12Vdc power therefore the kind of lock is limited e T2. T R USB RS485 communication terminal negative T R USB RS485 communication terninal positive PA program button A refer to program section PB program button B refer to program section f lu U 298 5 mm W oa D5 OF 114 5 mm JWB OUT JWP JWV OUT p2 MD2 MD1 P MA1 pP P VG VD D1 NC m a m Oo ag m Oo oO Oo Oo Oo JP LK For electronic lock safety type setting refer to Door Station Lock Connections 3 Place Name Lable Press down and shift right left to open the tracsparent nameplate cover then insert the name paper then put the plate cover back to the panel Note thar double button line panel can be opened both direction single button line Can only be opened at right side oo eae 4 Door Station Mounting Standard Installation Sac T mm H l HY Hated FH i i Open the mounting box of the panel use a cross screw to adjust the view angle of the camera before installation Installation with expanding panel Jointer 2 D o0o0 0 9g9g9g9099 9 gf i Stopper
3. A beep beep aa Card management soud hints show user card registered a long beep door open standby state show user card not registered beep beep beep Enter the card management state beept beep Exit out the card management state beep beep Card Add card Delete card Format successful beept management Adda already existed card beept beep sale Add card Delete card Format unsuccessful beep beep beep Add a debug card 16666666 beep beep beep beep Add card failure 1000 cards registered beep beep beep beep beep Card management LED hints Standby ON ON ON ON Authorize ADD Card ON OFF OFF ON Authorize DELETE Card OFF ON OFF ON Add user card ON OFF OFF OFF Delete user card OFF ON OFF OFF Format ON ON ORF OFF MR11 ID D8 7 Monitor Online Search Search the monitors controlled by the right row buttons Press PB button on door station in normal mode to activate searching monitors controlled by the right row buttons All LED indicator will blink twice then turn off Monitor online search is starting If the monitor is online the indicator of the corresponding button will light up and send out soud of beep If the monitor is not online the indicator will not light up and send out soud of beep beep beep Search the monitors controlled by the left row buttons Press PB button and hold for
4. Intelligent Intercom System 00000000000 000000000000 G lt QGdQOOOOdO0000 MR11 ID D8 MR11 S4 EP11 812 Read this manual carefully before using the product and keep it well for future use 1 Parts and Functions Camera Lens e Infrared LED e ID card window Microphone e Name plate e Call button Speaker Camera Angle adjustment 308 mm Connection Port 2 Terminal Descriptions CN LK 12V 12VDC power output LK GND power ground LK COM Common contact of the Relay NO Normally open with LK can be configured to normally close through ST Config EB Exit button connection port EB Exit button connection port RROG POWER D1 Data Receive D2 Data Transmit A1 Audio signal VD Video signal P Power positive output P Power negtive output P Power positive input P Power negtive input RS485
5. 3s on door station in normal mode to activate searching monitors controlled by the left row buttons All LED indicator will blink twice then turn off Monitor online search is starting If the monitor is online the indicator of the corresponding button will blink twice then light up and send out soud of beep If the monitor is not online the indicator will not light up and send out soud of beep beep beep Note e After all monitors had been searched the indicators of the corresponding buttons for all online monitors will blink twice then light up and send out soud of beep then the door station will exit out the search mode automatically During searching press the PB button on door station to exit manually 8 Specification e Power supply DC 18 24V e Camera Lens 1 3 inch color CCD e Power consumption Standby 0 5W Working status 15W e Video signal 1Vp p 750 CCIR standard e Unlock Power output 12Vdc 300mA e NO COM exchange contact Max 48V dc 1 5A e Monostable relay activation time 1 second to 10 minutes 5 e Working temperature 5 C 45 C e Wiring 6 wires polarity e Dimension 313 H x128 W x63 D mm The design and specifications can be modified without notice to the user Right to interpret and copyright of this manual are preserved Printed In China 2011 11
6. LED indicator willbe gt program shut off a beept beep 2 eee een Wee Oe Program user code for the second slave monitor which is the same as programmed for master monitor on door station gt in twice within 2s the selected call button indicator will be turned on the first slave monitor will be programmed with a user code as the same as the master monitor a beep beep We Continuously press the call button which is the same as programmed for master monitor on door station gt in 3 times within 2s the selected call button indicator will be turned on the first slave monitor will be programmed with a user code as the same as the master monitor Press PA button on door Press CALL button on station in normal mode to monitor or Audio Phone enter program mode which is assigned to All LED indicator willbe gt program shut off Pg beep beep on n bN Note The door station will exit out the program mode wether the programming is success or not all LED indicators will be recovered to turn on e Please repeat the operation from step 1 to step 3 to program the next monitor or next Audio Phone or the slave monitors e During programming if there isn t any operation within 60s when the CALL button has not been pressed on monitor or there isn t any operation within 10s when the CALL button has been pressed on monitor The door station will exit out the program mode auto
7. e user manual C Connection for Power to Unlock type set to Normally Open on the Unlock Relay mode default Note Cut off this line when Remove the Jumper ae using external power supply JP_LK D Connection for Power off to Unlock type set to Normally Closed on the Unlock Relay mode Note Cut off this line when Remove the Jumper using external power supply JP_LK 6 Door Station Configurations 1 About room code address Room code also called room address is a code assigned to each monitor to identify different monitors each monitor have a unique room code in one buidling The room code is stored in each Monitor s inner EEPROM memory and it won t be lost even the monitor is power off 2 User Code Programming Program user code for master monitor Press a call button on door Station in one time within 2s the selected call button indicator will be turned on the monitor will be Press CALL button on monitor or Audio Phone which is assigned to Press PA button on door station in normal mode to enter program mode All LED indicator will be program shut off a beep beep beep beep coal Program user code for the first slave monitor programmed with a user code Press CALL button on monitor or Audio Phone which is assigned to Continuously press the call button Press PA button on door Station in normal mode to enter program mode All
8. he rated power of the lock must be less than 12Vdc 300mA when using internal power supply mode e The GND must connect to the negative of the lock and the COM connect to the positive Jumper set to 2 3 position for Power off to Unlock safety type Normally closed mode set to 1 2 position for Power on to Unlock type Normally open mode If different unlocking time is needed to be configured the ST CONFIG software can be used to change the Unlock Timing on the Parameter tab for more detail information please refer to ST CONFIG software user manual A Connection for Power on to Unlock type set to Normally open on the Unlock Relay mode 12V 300mA Jumper set to 1 2 position mmm JP_LK B Connection for Power off to Unlock type set to Normally Closed on the Unlock Relay mode Jumper set to 2 3 position Oo JP_LK 2 External Power Supply Mode When the electronic lock is over 12 Vdc additional power supply for the lock is needed e The power supply for the lock must be less than 48Vdc 1 5A e The Jumper must be removed when using external power supply The default setting is Power on to Unlock type Normally open mode if use Power off to Unlock type change the Unlock Relay mode to Normally closed mode e If different unlocking time is needed to be configured the ST CONFIG software can be used to change the Unlock Timing on the Parameter tab for more detail information please refer to ST CONFIG softwar
9. mat gt operation is performing ID card window in standby mode S n Authorize master cards By default there are two master cards marked MASTER CARD ADD and MASTER CARD DELETE but you should know that the master card can be authorized by users at any time That means any two user cards can be authorized to master cards When registered new master cards the old master cards are invalid automatically _ _ beep beep beep beep _beep The second card shown is the MASTER CARD DELETE card it will return to standby if no operation within 10s The first card shown is the MASTER CARD ADD card it will return to standby if no operation within 10s When the door station is in standby press PA button and hold for 3 seconds to get into the master card manage state A beep a Add User Cards by Room Show the MASTER CARD ADD card to ID card window in standby mode a beep beep Delete User Cards by Room Show the MASTER CARD ADD card to exit But it will return to standby mode if no operation within 15s Press a call button on door station then show the user cards to be added for the room which to be assigned Show the MASTER Press the call button CARD DELETE card to on door station which is CARD DELETE card ID card window in standby authorized to the room to exit But it will return to mode gt standby mode if no operation within 15s Show the MASTER
10. matically beep beep beep will be sent out from door station and all LED indicators will be recovered to turn on 3 ID Card Registration just for the model with ID function Introduction e Up to 1000 user cards can be registered by the door station e Easy management with LED status and sound hints e There are two master cards one MASTER CARD ADD card and one MASTER CARD DELETE card When registered new master cards the old master cards are invalid automatically e Card reading distance is from 3 to 5 cm e The master cards are necessary when you add or delete user cards Please keep it well for future use Add User Cards Show user cards to be added one by one Show the MASTER CARD ADD card to ID card window in standby mode Delete User Cards Show user cards to be deleted in sequence Show the MASTER CARD DELETE card to ID card window in standby mode YY MASTER CARD ADD QS MASTER CARD Show the MASTER CARD ADD card to exit But it will return to standby mode if no operation within 15s a beep beep eo oe show the MASTER CARD DELETE card to exit But it will return to within 15s gt standby mode if no operation beep beept ie Access Initialization delete all user cards Show the MASTER CARD DELETE card to Show the MASTER CARD ADD card to ID card window Show the MASTER CARD ADD card to ID card window again for
Download Pdf Manuals
Related Search