Back-UPS RS
Contents
1. CONNECT BATTERY CARTRIDGE 6 OPERATING ENVIRONMENT C RJ 11 RJ 11 af www apc com To p io USB RJ 45 RS 1000 RS 1500 Sa f 24 inches PA xX w LS YW evo F 4 fal fil MEI w CO 9 CONNECT EQUIPMENT POWER connect PHONE MODEM FAX QO CONNECT 10 100 Base T or VOIP Q CONNECT INTERFACE CABLE INSTALL SOFTWARE ON Phone Jack T COMPUTER mj For connection of APC s optional external 24 volt battery pack BR24BP to the Back UPS RS 1500 Network Jack OD gt me Follow the m f 2 i To sell USB i on screen Monitor lt Computer USB RJ 45 Da2. is a simple task requiring use of the front panel pushbutton To adjust the transfer voltage proceed as follows 1 Plug the Back UPS into the utility power source The Back UPS will be in a Standby Mode no indicators lit no power to Battery Backup outlets 2 Press the front panel pushbutton fully inward for 10 seconds All indicators on the Back UPS will flash to acknowledge going into Programming Mode 3 The Back UPS will then indicate its current Lower Transfer Voltage as shown in the following table Indicators Lit Lower Transfer Voltage Sensitivity l 155 Vac Use only for extreme conditions of Low low input voltage Not recommended for computer loads 2 165 Vac Back UPS frequently goes On Medium Battery due to low input voltage 3 175 Vac High factory default Connected equipment is sensitive to low voltage recommended 4 To select 155 volts as the Lower Transfer Voltage press the push button until 1 indicator is flashing 5 To select 165 volts as the Lower Transfer Voltage press the push button until 2 indicators are flashing 6 To select 175 volts as the Lower Transfer Voltage press the push button until 3 indicators are flashing Once in Programming Mode if the pushbutton is not pressed within 5 seconds the Back UPS will exit Programming Mode all indicators will extinguish Declaration of Conformity Application of Council Directives 73 23 EEC 93 68 EEC 91 157 EEC Standards to
3. 5 lbs Shipping Weight 1000 VA 11 kg 25 Ibs 1500 VA 12 kg 28 Ibs EMI Classification EN 50091 1 EN 60950 EN 50091 2 EN 61000 3 2 EN 6100 3 3 EN 55022 Class B On Battery Run Time See http www apc com product LIMITED WARRANTY The standard warranty is two 2 years from the date of purchase APC s standard procedure is to replace the original unit with a factory reconditioned unit Customers who must have the original unit back due to the assignment of asset tags and set depreciation schedules must declare such a need at first contact with an APC Technical Support representative APC will ship the replacement unit once the defective unit has been received by the repair department or cross ship upon the receipt of a valid credit card number The customer pays for shipping the unit to APC APC pays ground freight transportation costs to ship the replacement unit to the customer Back UPS does not provide expected backup time Back UPS battery cartridge is discharged due to recent power outage and has not had time to recharge Battery has reached the end of its life Replace battery cartridge see Order Replacement Battery Cartridge Internal battery cartridge is not connected Connect battery cartridge see Connect Battery Cartridge Charge the battery cartridge for 8 hours Back UPS runtime is reduced until the battery cartridge is fully charged Red Replace Battery indicator is flashing Green On Line indica
4. E ded whenever a low battery condition will stick out if an overload condition forces o gt aan vi i 4 Have the Back UPS model number serial is reached Battery run time is very low the Back UPS to disconnect itself from number and date of purchase available Be Ea o Promptly save any work in progress and utility power If the button sticks out prepared to troubleshoot the problem with an E On Line green is lit whenever utility exit all open applications Shutdown the disconnect non essential equipment Reset APC Technical Support tati If 4 S J pport representative power is powering the Battery Backup operating system computer and the Back the circuit breaker by pushing the button this is not euceecshal APC will issue a Modem outlets UPS inward Return Merchandise Authorization RMA Phone Fax number and a shipping address TROUBLESHOOTING SPECIFICATIONS Possible Cause Corrective Action Back UPS not connected to AC power source Ensure the Back UPS is securely connected to an AC outlet Back UPS circuit breaker tripped Disconnect non essential equipment from the Back UPS Reset push in the rear panel circuit breaker Switch on the Back UPS and plug in devices one at a time If the circuit breaker trips again disconnect the device that caused the breaker to trip Utility input voltage is out of range Consider adjusting the transfer voltage and sensitivity See Transfer Voltage and Sens
5. Which Conformity Declared EN50091 1 1 EN60950 Manufacturer s Name and Address American Power Conversion 132 Fairgrounds Road West Kingston Rhode Island 02892 USA or American Power Conversion Philippines Second Street Cavite EPZA Rosario Cavite Philippines or American Power Conversion India Private Limited No 187 3 amp 188 3 Jigani Village Jigani Hobli Anekal Taluk Bangalore District India American Power Conversion A P C b v Ballybritt Business Park Galway Ireland Uninterruptible Power Supply BR1000 FR BR1500 FR X0301 000 000 X0252 999 999 X0401 000 000 X0352 999 999 2003 2004 Where X PB GB FB NB BB or YB Importer s Name and Address Type of Equipment Model Numbers Serial Numbers Years of Manufacture Note We the undersigned hereby declare that the equipment specified above conforms to the above directives Stephen G Williams Regulatory Compliance Engineer ia Ray Ballard Managing Director Europe Billerica MA Place Date Galway Ireland Place Date 990 1396A 5 03 Copyright 2003 American Power Conversion All rights reserved APC PowerChute Personal Edition and Back UPS are registered trademarks of American Power Conversion All other trademarks are the property of their respective owners
6. f the Back UPS On Line On ae battery of the Back UPS is powering demand has exceeded the capacity of the x battery is near the end of its useful life or carrier The Back UPS features a transient IN l l Battery Overload and Replace Battery equipment connected to the Battery Back UPS if the battery is not connected see above If the Back UPS d t voltage surge suppression TVSS Backup Outlets A battery that is near the end of its useful Foa gee ee ee screw for connecting the ground lead life has insufficient run time and should be Tu Mt to the dealer The following steps on additional surge suppression devices oe i a Conti replaced should be taken l Continuous Tone this alarm is sounded l l such as network and data line surge Je ies Four Beeps Every 30 Seconds this whenever the Battery Backup outlets are 7 1 Consult the Troubleshooting section to protectors E alarm is sounded whenever the Back UPS overloaded Chirps for 1 Minute Every 5 Hours this eliminate common problems is running On Battery Consider saving alarm is sounded whenever the battery has 2 If the problem persists go to http 2 oveibad N work in progress N failed the automatic diagnostic test www apc com support Cc Circuit Breaker the circuit breaker button b 3 If the problem still persists contact APC Pom Paa ine X Replace Battery Continuous Beeping this alarm is located on the rear panel of the Back UPS Technical Support
7. itivity Adjustment Equipment plugged into a Surge Only outlet Unplug device from Surge Only outlet and move to a Battery Backup outlet Item Specification On line Input Voltage Range 175 295 Vac default settings Automatic Voltage Regulation AVR On line Frequency Range 47 63 Hz autosensing On battery Waveshape Stepped Sine Wave Maximum Load 1000 VA 600 W 1500 VA 865 W Operating Temperature 0 to 40 C 32 to 104 F Storage Temperature Problem Back UPS will not switch on Back UPS does not power essential equipment during an outage Back UPS operates on battery although utility power exists Back UPS circuit breaker tripped Disconnect non essential equipment from the Back UPS Reset push in the rear panel circuit breaker Switch the Back UPS on and plug equipment in one at a time If the circuit breaker trips again disconnect the device that caused the breaker to trip Utility input voltage is out of range Consider adjusting the transfer voltage and sensitivity See Transfer Voltage and Sensitivity Adjustment Back UPS is heavily loaded Unplug non essential equipment printers scanners etc from the Battery Backup outlets and plug into Surge Only outlets 5 to 45 C 23 to 113 F Operating Storage Relative 0 to 95 non condensing Humidity Size H x W x D 37 1 x 8 6 x 33 3 cm 14 6 x 3 4 x 13 1 inch Weight 1000 VA 10 kg 22 Ibs 1500 VA 11 kg 2
8. ta Port 4 BR24BP Battery Pack instructions Network Port oo Loi 5 Printer or Scanner Computer vob a gt Path yo Lf ASR oan on S gt Computer NOTE Macintosh Users for full USB External Disk or Ri performance use OS 9 22 or higher CD DVD Drive gt If Autoplay is not enabled on the computer SWITCH ON THE BACK UPS ORIENTATION a a FAX Note Allow the Back UPS to charge fora When Self Test has successfully 1 On the computer desktop of the display full eight 8 hours prior to use completed only the green On Line double click on My Computer Ea int 20 24 Press the front panel Power ON OFF switch indicator will be lit oe 2 Double click on the CD ROM drive icon et eee and follow the on screen instructions and observe that the following events occur If the internal battery cartridge is not NE Computer after pressing and releasing the switch connected see Step 2 above the green ene On Line indicator and red Replace Battery ypme lP IG i M E naira indicators will light The Back UPS will e Kiila e The yellow On Battery indicator lights also emit a chirping sound while a Self Test is being performed CONNECT TVSS GROUND a m o J I There are four status indicators lights on the On Battery yellow is lit whenever the Q O Overload red is lit whenever power Replace Battery red is lit whenever the If the Back UPS arrived damaged notify the front panel o
9. tor is on Red Replace Battery indicator is Battery has reached the end of its life Replace the battery cartridge see Order Replacement on Battery Cartridge Red Overload indicator is on or Connected equipment is drawing more power Move one or more equipment power plugs from Battery flashing than the Back UPS can provide Backup outlets to Surge Only outlets Green On Line indicator is on Internal UPS fault Contact APC Technical Support see Contact Information and all front panel indicators are flashing ORDER REPLACEMENT BATTERY CARTRIDGE The battery cartridge typically lasts 3 6 years shorter if subjected to frequent outages or elevated temperatures Order part number RBC32 for 1000 VA models or RBC33 for 1500 VA models CONTACT INFORMATION Technical Support REPLACE BATTERY CARTRIDGE http www apc com support Internet http www apce com esupport apcc com 353 91 702020 1 401 789 5735 1 401 789 5735 Europe Middle East Africa USA Canada Worldwide atte Cartridge TRANSFER VOLTAGE AND SENSITIVITY ADJUSTMENT In situations where the Back UPS or connected equipment appears too sensitive to input voltage it may be necessary to adjust the transfer voltage This
Download Pdf Manuals
Related Search