MANUAL DO USUÁRIO
Contents
1. 000 018 019 037 038 058 076 094 095 113 114 127 man man Rotating clockwise with increasing speed 192 255 Rotating counter clockwise with increasing speed E GW te oes le PP Gobo Rotation PP Gobo Rotation 000 009 116 117 244 1 192 255 245 255 Fix Po EivGobe e SE AA A 006 245 255 000 006 014 020 049 055 105 111 119 125 126 192 Rotating clockwise with increasing speed 193 255 Rotating counter clockwise with increasing speed 10 009 016 250 255 045 064 245 255 Ce a O o Prism 000 015 000 255 Focus Near Far 02 105 111 25 1 eg 92 Rotating clockwise with increasing speed Rotating counter clockwise with increasing speed Po Strobe SE te 017 249 228 E Po Dimmer e SE 000 255 a tor Po Prism A E II 000 255 Focus Near Far 1 198255 4 Operating Instructions 16 ELECTRA LIGHT DMX Channel Values for 10 or 13 channel Advanced Mode 13 channel Basic Mode 10 channel CHANNEL VALUE FUNCTION CHANNEL VALUE EC 000 255 000 255 X Y Speed Ee Fast Slow Po lor e S 016 031 032 047 048 063 064 079 080 095 096 111 112 127 128 191 Rotating clockwise with rainbow effect 192 255 Rotating counter clockwise with one effect GoboWheel Wheel 000 018 019 037 076 094 128 191 Rotating clockwise with increasing speed 192 255 Rotating counter clockwise with increasing speed X Y Speed DE2. Press lt MENU gt using lt UP gt and lt DOWNsselect until lt Reversal gt appears on the LCD screen 2 Press lt ENTER gt 3 Using lt UP gt and lt DOWN gt Select lt PAN gt or lt TILT gt 4 Press lt ENTER gt Using lt UP gt and lt DOWNs gt Select degree lt PAN nomal reversal gt or lt TILT nomal reversal gt 5 Press lt ENTER gt Reset This fixture has preprogrammed reset triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation 1 Press lt MENU gt using lt UP gt and lt DOWNsselect until lt Reset gt appears on the LCD screen 2 Press lt ENTER gt 3 lt YES gt appears on the LCD screen 4 Press lt ENTER gt Load Data This fixture has preprogrammed load data triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation 1 Press lt MENU gt using lt UP gt and lt DOWNsselect until lt LOAD DATA gt appears on the LCD screen Press lt ENTER gt lt YES gt appears on the LCD screen Press lt ENTER gt ON 4 Operating Instructions 14 ELECTRA LIGHT Master Slave This is the operating mode which will allow one fixture to act as the master and control all of the other slave fixtures You must set both the master and the slave s fixtures to the correct mode for this operation Please see the diagram below on the connections for your fixtures as well as the setting to assign in the control
3. panel It is not necessary to arrange the master fixture as the first fixture in the daisy chain It may be any fixture in the daisy chain For example fixture 2 5 10 or 12 etc oe Only 1 fixture may be set to master In order to mirror one fixture to another you may invert the pan and tilt on the mirrored fixture 1 E Do not connect a DMX controller to the daisy chain for this operating mode a DMX OUT Set this fixture to master mode Set this fixture to Set this fixture to slave mode slave mode Master slave Slave DMX OUT DMX IN DMXOUT DMXAN DMX OUT Additional signal DMX link out 4 Operating Instructions 15 DMX Channel Values for 10 or 15 channel Advanced Mode 15 channel ELECTRA LIGHT CHANNEL VALUE FUNCTION 000 255 Pan 000 255 Basic Mode 10 channel O 3 O 000 255 000 255 Tit Fine CHANNEL VALUE FUNCTION 000 255 X Y Speed Color 048 063 096 111 128 191 Rotating clockwise with rainbow effect 199 955 Rotating counter clockwise with rainbow effect 000 018 019 037 057 075 076 094 114 127 428 191 Rotating clockwise with increasing speed 192 255 Rotating counter clockwise with increasing speed ooo GoboRotation O Gobo Rotation 000 009 NO Function 010 116 Rotate clockwise slow fast 417 244 Rotate counter clockwise slow fast ssp ts ae 5 032 047 048 063 096 111 192 255 SE counter clockwise with rainbow e A PR GoboWheedl E Wheel
4. ELECTRA LIGHT CLUB 60 MANUAL DO USU RIO ELECTRA LIGHT 1 BEFORE YOU BEGIN What is included 1x Spot 1 x Power cable 1 x User Manual YYYY Unpacking Instructions 1 x Mounting bracket and screws Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Manual Conventions manuals use the following conventions to differentiate certain types of information from the regular text CONVENTION 10 lt Menu gt 1 512 50 60 Settings MENU gt Settings ON Icons MEANING A LCD display to be configured A key to be pressed on the tixture s control pane A range of values A set of values of which only one can be chosen A menu option not to be modified for example showing the operating mode current status A sequence of menu options to be followed A value to be entered or selected This manual uses the following icons to indicate information that requires special attention on the part of the user ICONS N MEANING T
5. Normal Pan Norman Scan Pan Reversal Pan Reversal Scan Reversal an 10CH Channel Personality Basic Load Data Load Default 4 Operating Instructions 12 ELECTRA LIGHT DMX Operation This is the operating mode which will allow for control with an external DMX controller You must set the starting address for this mode If this is your first time using DMX then it is recommended that you refer to the DMX Primer section in the Appendix of this manual ja MA Press lt MENU gt using lt UP gt and lt DOWN gt select until lt ADRESS gt appears on the LCD screen Press lt ENTER gt Using Value Button lt UP gt and Digit Button lt DOWN gt select DMX DATA lt 001 512 gt Press lt ENTER gt Standalone Operation Automatic Fast This fixture has preprogrammed fast chases These are accessed via the control panel Please see the Instructions Below for further explanation 1 2 3 4 Press lt MENU gt using lt UP gt and lt DOWN gt select until lt INSET gt appears on the LCD screen Press lt ENTER gt Select lt AUTOFAT gt Press lt ENTER gt Automatic Slow This fixture has preprogrammed slow chases These are accessed via the control panel Please see the Instructions Below for further explanation 1 Press lt MENU gt using lt UP gt and lt DOWN gt select until lt INSET gt appears on the LCD screen 2 Press lt ENTER gt 3 SelectcAUTOSLOW 4 Press lt ENTER gt Sound Active This fixture has prep
6. ace DMX input Faulty Main PCB Replace Main PCB Non DMX cables Use only DMX compatible cables Bouncing signals Install terminator as suggested B bee Long cable Low level signal Install amplifier right after fixture with strong signal Too many fixtures Install an optically coupled DMX splitter after unit 32 Interference from AC wires Keep DMX cables separated from power cables or black lights 5 Appendix 21 ELECTRA LIGHT Technical Specifications WEIGHT amp DIMENSIONS le d a E S 250 mm o o e 255 mm A A A 360 mm o ATER 6 kg POWER Autoswitching Power Supply ccccccccncnnccccononnnananonnnnnnnnnnnnnnnnnnnnnnnnnnannnn nono nnnnnnos 100 240 VAC 50 60 Hz Power Consumption 120 VAC 60 HZ cocccccnnnccccnncncncnoncncnonononcnnnnnnnnnos 148 W 0 1 A max 2 A inrush Power Consumption 230 VAC 50 HZ coccocccccccccnnnooococonnnnnnnnnonononanonenons 144 W 0 5 A max 1 A inrush REENEN 4 units max TEE F 2 A 250 V LIGHT SOURCE A 1 white 60 W 13 5 A 50 000 hrs PHOTOOPTIC Lumimeanae A 18 000 lux BeO E le EE 142 GOBOS TSS lo A uo e 23 8 mm Made ame actas 20 mm Maximum TANCK NGS Sinna i i p E E 2mm THERMAL Maximum ambient temperature A 104 F 40 C WARRANTY INFORMATION A 1 year limited warranty Technical Specifications 17
7. e see the diagram below for further explanation POWE 3 Setup 8 ELECTRA LIGHT Signal Linking DMX The diagrams below illustrate the signal DMX linking for this fixture This is used both in DMX mode and when operating the fixtures in Master Slave mode Please see the diagram below for further explanation DMX OUT Second fixture First fixture ST DMX OUT D DMX OUT pin DMxXOUT DMX IN DMX controller Only in OMX operation Additional signal DMX link out Fuse Replacement Disconnect the power cord before replacing a fuse and always replace with the same type fuse With a flat head screwdriver unscrew the fuse holder out of its housing turning counter clockwise Remove the damaged fuse from its holder and replace with exact same type fuse Insert the fuse holder back in its place and reconnect power E ag gt POWER ES S The fuse is located inside this fuseholder FUSE 3 Setup 9 ELECTRA LIGHT Mounting Orientation The Spot may be mounted in any safe position provided there is adequate room for ventilation Rigging Be sure that the structure can support 10 times the weight of the fixture Please see the Technical Specifications section of this manual for a detailed weight listing Mount the fixture securely Two hanging clamps for truss mounting may be used or nuts and bolts for permanent installation may be used The holes in each bracket are 13 mm in s
8. his paragraph contains critical installation configuration or operation information Failure to comply with this information may render the fixture partially or completely inoperative cause damage to the fixture or cause harm to the user This paragraph contains important installation or configuration information Failure to complv with this information mav prevent the fixture from functioning correctly This paragraph reminds you of useful although not critical information 1 Before You Begin ELECTRA LIGHT Safety Instructions 1 Before You Begin Please read these instructions carefully It includes important information about the installation usage and maintenance of this product Please keep this User Manual for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure there are no flammable materials close to the unit while operating The unit must be installed in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots are blocked Always disconnect from power source before
9. ir compressor and a soft brush to remove dust collected on external vents Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint The cleaning of external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates Damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Clean the external optics at least every 20 days Clean the fixture at least every 30 60 days Always dry the parts carefully after cleaning them Never spin a fan using compressed air 18 ELECTRA LIGHT Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run synchronized shows on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support 485 standard no more than 32 fixtures should be connected on one data link Connecting more than 32 fixtures on one serial data link without the use of a DMX optical
10. ize When rigging consider routine maintenance and control panel access Please see the following steps for installation Ifthe power link out is intended to be used with multiple fixture take into account the length of each power cable and mount the fixtures close enough to one another to accommodate for this Attach both included bolts in the locations indicated below using a metric 8 mm Allen wrench Attached 2 hanging clamps to the bracket in each of the two locations indicated below Safetv cables must always be used Do NOT mount this fixture sideways Mounting bracket o Q Safety cable attachment point Mounting bracket Be sure to loop the safety cable through the 1 loop as shown Fa fm in the illustration above K di The safety cable must be po Af capable of support up to 10 l l times the weight of the fixture 3 Setup 10 ELECTRA LIGHT 4 OPERATING INSTRUCTIONS Configuring the Starting Address Each fixture requires a starting address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the starting address For example a fixture that uses seven DMX channels and is addressed to start on DMX channel 100 will read data from channels 100 101 102 103 104 105 and 106 Choose the starting addresses for each fixture so that the channels used do not overlap In addition you should note the starting address selected for future
11. l terminator common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other O Do not allow contact between the common and the fixture s chassis ground Grounding the 5 Appendix 19 3 Pin to 5 Pin Conversion Chart ELECTRA LIGHT If you use a controller with a 5 pin DMX output connector you will need to use a 5 A pin to 3 pin adapter The chart below details a proper cable conversion 3 PiN TO 5 PIN CONVERSION CHART Ground Shield Pin 1 Data signal Pin 2 Data signal Pin 3 Not used Not used Setting up a DMX Serial Data Link 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the controller 2 Connect the end of the cable coming from the controller which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector 3 Then proceed to connect from the output as stated above to the input of the following fixture and so on Setting the Starting Address Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Universal DMX Controller id sz TI I AO 232 Nr a ae e Ig This drawing provides a general illustration of the DMX input output panel of a lighting fixture Continue the link This DMX mode enables the use of a universal DMX controlle
12. lap If they do this will result in erratic operation of the fixtures whose starting address is set incorrectly You can however control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation In other words the fixtures will be slaved together and all respond exactly the same DMX fixtures are designed to receive data through a serial Daisy Chain A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture Use an order that provides for the easiest and most direct cabling Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors The shield connection is pin 1 while pin 2 is Data Negative S and pin 3 is Data positive S General Maintenance O A 5 Appendix To maintain optimum performance and minimize wear fixtures should be cleaned frequentiv Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or a
13. ly isolated splitter may result in deterioration of the digital DMX signal Fixtures on a serial data link must be daisy chained in one single line To comply with the ElA Maximum recommended serial data link distance 500 m 1640 ft Maximum recommended number of fixtures on a serial data link 32 Data Cabling To link fixtures together you must obtain data cables You can purchase certified DMX cables directly from a dealer distributor or construct your own cable If you choose to create your own cable please use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference DMX Data Cable Use a BeldenO 9841 or equivalent cable which meets the specifications for EIA RS 485 applications Standard microphone cables cannot transmit DMX data reliably over long distances The cable must have the following characteristics Type shielded 2 conductor twisted pair Maximum capacitance between conductors 30 pF ft Maximum capacitance between conductor and shield 55 pF ft Maximum resistance 20 ohms 1000 ft Nominal impedance 100 140 ohms Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end DMX connector configuration 120 ohm 1 4 W resistor between pin 2 DMX and pin 3 DMX on the output of the last fixture To avoid signal transmission problems and interference it is always advisable to connect a DMX signa
14. n Fast Slow nm E ene Color 1 Color 2 Color 2 Color 4 080 095 Color 5 096 111 Color 6 Color 7 Rotating clockwise with rainbow effect Rotating counter clockwise with rainbow effect Gobo Wheel 000 018 White 019 037 Gobo 1 038 056 Gobo 2 057 075 Gobo 3 076 094 Gobo 4 095 113 Gobo 5 oun 1 MEE speed 010 116 Rotate clockwise slow fast 417 244 Rotate counter clockwise slow fast 245 255 ae Dame S buten 000 255 Focus Near Far om 192 255 Rotating counter clockwise with increasing speed Gobo Rotation a NO Function ETE 0 116 Rotate clockwise slow fast IS 44 Rotate counter clockwise slow fast 245 255 Strobe Bimmer Bimmer ln 245 255 No function 114 127 Gobo 6 PP Gobo Rotation mun aan Rotating clockwise with increasing 000 009 NO Function 000 255 MovementMacros Macros EN A 4 Operating Instructions 17 ELECTRA LIGHT 5 APPENDIX DMX Primer There are 512 channels in a DMX connection Channels may be assigned in any manner A fixture capable of receiving DMX will require one or a number of sequential channels The user must assign a starting address on the fixture that indicates the first channel reserved in the controller There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required Choosing a start address should be planned in advance Channels should never over
15. r device Each fixture requires a start address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that uses six DMX channels and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 and 105 Choose start addresses so that the channels used do not overlap and note the start address selected for future reference If this is your first time addressing a fixture using the DMX control protocol we suggest jumping to the Appendix section and reading the heading DMX Primer It contains very useful information that will help you understand its use 5 A di ppendix 20 ELECTRA LIGHT General Troubleshooting SYMPTOM PossiBLE CAUSE S POSSIBLE ACTION S Excessive circuit load Check total load placed on the electrical circuit Breaker Fuse a MI E SS keeps blowing Short circuit along the power Check for a short in the electrical wiring internal and or wires external Device doesnot No power Check for power on power outlet power up Loose power cord Check power cord Wrong DMX addressing Check Control Panel and unit addressing Damaged DMX cables Check DMX cables Wrong polarity settings on the Fixture is not l l Check polaritv switch settings on the controller responding to controller DMX Loose DMX cables Check cable connections Faultv DMX interface Repl
16. reference The Spot fixture uses eleven or sixteen DMX channels If this is your first time using DMX we recommend reading the DMX Primer section in the Appendix Control Panel Functions Access control panel functions using the four buttons located directly underneath the LED display on the included wired remote Nero FUNCTION current operating mode AMENA as well as back out of the current menu option Ys of has Used to select decreasing FONERILED SOW lt DOWN gt E advancement in the value lt UP gt Used to select increasing advancement in the value Used to select a value and SEND store it to memory MENU UP DOWN ENTER The Control Panel shows the current state of the unit It is used to select the operating mode as well as the sub features For a detailed layout of the control panel functions please see the menu map section on the following page 4 Operating Instructions 11 ELECTRA LIGHT Menu Map Auto Fast Auto Slow Standalone Fast selection Standalone Fast mode display Standalone Slow selection Standalone Slow mode display Standalone Studio selection Standalone Studio mode display Standalone Slave selection Sets the fixture to respond to another fixture set to master Standalone Slave mode display Sets the fixture to respond to another fixture set to master Tilt Tit Reversal Scan Degree 15CH or 13CH SS Channel Personality Advanced 1 es
17. reset of pan tilt color gobo prism focus Move in black for pan tilt color gobo Built in movement macros via DMX automated and sound Additional Features Built in automated programs via master slave Built in sound active programs via master slave High power 60 W 13 5 A LED User selectable pan tilt ranges Pan 540 360 180 Tilt 270 180 90 Automatic pan amp tilt correction User selectable basic or advanced operating modes Additional power output max 4 units Photometrics i lux DO Distance m KI SHEI Loi ELECTRA LIGHT 2200 2 Introduction 5 ELECTRA LIGHT 2 Introduction ELECTRA LIGHT Product Overview Front lens Tilt Pan CES S D A arsa Control LJ ls Y Standing feet Panel DMX IN Pow Fuse Holder DMX OUT 2 Introduction a ELECTRA LIGHT 3 SETUP AC Power This fixture runs on 100V or 240 VAC 50 60 Hz This fixture used switch power supply it can transform by itself when user input power variable resistor or dimmer circuit even if the rheostat or dimmer channel is used only as a 0 Always connect the fixture to a switched circuit Never connect the fixture to a rheostat to 100 switch Always connect the fixture to a circuit with a suitable electrical ground The maximum quantity of fixtures that may be linked is 4 Power Linking This fixture contains power linking via the edison outlet located in front of the power input cable Pleas
18. rogrammed sound triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation i 2 3 4 Channel Press lt MENU gt using lt UP gt and lt DOWN gt select until lt INSET gt appears on the LCD screen Press lt ENTER gt Select lt SOUND gt Press lt ENTER gt This fixture has preprogrammed channel triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation eM Press lt MENU gt using lt UP gt and lt DOWN gt select until lt CHANNEL gt appears on the LCD screen Press lt ENTER gt Using lt UP gt and lt DOWN gt Select lt 15CH gt or lt 13CH gt Press lt ENTER gt 4 Operating Instructions 13 ELECTRA LIGHT Degree This fixture has preprogrammed degree triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation 1 Press lt MENU gt using lt UP gt and lt DOWN gt select until lt DEGREEL gt appears on the LCD screen Press lt ENTER gt Using lt UP gt and lt DOWN gt Select lt PAN gt or lt TILT gt Press lt ENTER gt Using lt UP gt and lt DOWNs Select degree lt PAN 540 360 180 gt or lt TILT 270 180 90 gt 6 Press lt ENTER gt Che els Reversal This fixture has preprogrammed reversal triggered chases These are accessed via the control panel Please see the Instructions Below for further explanation 1
19. servicing or replacing fuse and be sure to replace with same fuse source Secure fixture to fastening device using a safety chain Maximum ambient temperature Ta is 104 F 407 C Do not operate fixture at temperatures higher than this In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Never connect the device to a dimmer pack Make sure the power cord is never crimped or damaged Never disconnect the power cord by pulling or tugging on the cord Never carry the fixture directly from the cord Always use the hanging mounting bracket Avoid direct eye exposure to the light source while it is on Never carry the fixture by holding the head Always use the carrying handle 2 INTRODUCTION Features 10 or 15 channel and 10 or 13 channel DMX moving yoke Pan 540 tilt 270 Color wheel 7 colors white Split colors Rainbow effect Gobo Wheel 1 10 or 13 channel not include this Gobo wheel 8 static gobo open rainbow effect Gobo Wheel 2 6 gobo open 6 glass installed Rainbow effect Gobo shake 3 facet prism 10 or 13 channel not include 3 facet prism Variable electronic shutter for strobing Variable motorized focus Variable electronic dimmer 0 100 Remote fixture reset amp vector speed channel Individual
Download Pdf Manuals
Related Search