Control Pads On The Dehumidifier
Contents
1. N Perfect re Your Source for Home Comfort 30 50 amp 70 PINT DEHUMIDIFIER USER MANUAL FOR MODELS 3PAD3O 3PAD50 3PAD7O An na i NINII Before using your dehumidifier please read this manual carefully and keep it for future reference along with your receipt Quick Start Tips It is highly suggested that the manual be read in full before operating the unit However the notes below are especially important in helping you to properly set up and begin to use your dehumidifier 1 The dehumidifier should be kept upright If for any reason it has not been stored upright while in your possession put the unit in an upright position for a minimum of 24 hours before running it When first using the dehumidifier operate the unit on continuous mode for 24 hours CD First 24 hours on Continuous Mode Cont After the first 24 hours should you wish to set a desired humidity you will need to take the unit off of Continuous You will not be able to select a desired humidity while the unit is set on Continuous mode NOTE You do not need to be in Continuous mode to do continuous draining When unpacking the dehumidifier note that the foam inside the float piece of the bucket should NOT be removed Without this foam piece the dehumidifier will not operate properly Foam piece inside float mechanism DO NOT REMOVE this foam piece The accessories are locat2. NOTES When you remove the bucket do not touch any parts inside of the unit Doing so may damage the product e Be sure to push the bucket gently all the way into the unit Improper installation or failing to push it in securely may cause the unit not to operate e When you remove the bucket be sure to wipe away any excess moisture found inside the unit OPTION 2 Continuous draining OPTION 2 CONTINUOUS DRAINING Water can be automatically emptied into a floor drain by attaching a water Fig 7 Drain Tube Subassembly hose garden hose or dehumidifier drain hose to the dehumidifier Hose must Adapter A have a female threaded end Hose not included Drain tube SN If not already assembled put together the Drain Tube Subassembly by securely connecting the drain tube included to adapter A included See Fig 7 Drain tube and adapter can be found inside the bucket Remove the rubber plug from the drain outlet on the back of the unit and set Rubber plug aside Remove bucket to access connector Insert the drain hose through pa the unit s drain outlet from the back of the unit going forward and securely 9 Drain tube 1 subassembly press it into the connector on the front of the unit Fig 9 Tighten adapter A to the unit by using the two screws provided which can be found inside a pouch in the packaging for this user manual Install the female threaded end of the water hose garden hose or dehumidifier drain hose
3. Be sure unit is not too large or too small for the area of the room Using unit in much less than its stated coverage will likely cause it to go on and off more frequently Using too small of a unit will cause it to run constantly If the humidity setting and actual humidity in room are cycling right around the same the unit would go off and DEHUMIDIFIER on accordingly CONSTANTLY CYCLES The fan will run for a few minutes after the compressor shuts off If you have turned the Continuous mode on ON OFF the fan and compresser will not turn off they will run continuously in this mode Check that unit is level and the filter vents and bucket are thoroughly clean and nothing is obstructing them Be sure all doors windows and other openings are securely closed Ensure there is sufficient air circulation around the unit as well as between unit and floor Unplug unit for at least 5 minutes Plug back in unit remove and return bucket to dehumidifier and turn on ES AS P2 EC or E1 X APPEARS ON THE DISPLAY These are error and protection codes See page 6 of this manual for more information Continued on next page 11 Troubleshooting Tips continued Before calling for service please review the chart below Question DEHUMIDIFIER ALWAYS RUNNING CONTINUOUS DRAIN NOT WORKING PROPERLY UNIT DOES NOT START UNIT MAKES A LOUD NOISE WHEN OPERATING WATER ON FLOOR UP AND DOWN PADS ON CONTROL PANEL DO NOT ALLOW US
4. CAUTION Contact an authorized service technician for repair or maintenance of this unit Contact an installer for installation of this unit if necessary The dehumidifier is not intended for use by young children without supervision Young children should be supervised to ensure that they do not play with the air conditioner Disabled persons may require assistance with set up and usage If the power cord is to be replaced replacement work should be performed by authorized personnel only Installation and repair work must be performed in accordance with the national wiring standards by authorized personnel only Safety Precautions To prevent injury to the user or other people and property damage the following instructions must be followed Incorrect operation due to ignoring instructions may cause harm or damage MM Failure to adhere to each of the following precautions can lead to results classified as follows A N WARNING This symbol indicates the possibility of death or serious injury A CAUTION This symbol indicates the possibility of injury or damage to property Ml Meanings of symbols used in this manual are as shown below SO Never do this D Always do this AN AN WARNING SDo not exceed the rating of SDo not operate or stop the SDo not damage or use an the power outlet or unit by inserting or pulling unspecified power cord connection device out the power plug directl
5. Aire Consumer Services ES Temperature sensor error Unplug the unit for at least 5 minutes and plug it back in Perfect Aire Consumer Services P2 Bucket is full or not in the correct position Empty the bucket and replace it in the proper position Ensure float switch and foam are secured properly in bucket Other Features Bucket Full Indicator Light Illuminates when the bucket is ready to be emptied is removed or is not replaced in the proper position Auto Shut Off The dehumidifier shuts off after 30 seconds when the bucket is full or when the bucket is removed or not replaced in the proper position When the humidity setting is reached the unit will cycle off automatically The compressor cycles off first Three minutes later the fan will turn off as well Auto Defrost When frost builds up on the evaporator coils the compressor will cycle off and the fan will continue to run on Turbo until the frost disappears The Auto Defrost Indicator light will illuminate The unit will restart on its own once the auto defrost process has completed Safety Feature After the unit has stopped it cannot resume operation in the first 3 minutes afterwards This is to protect the unit Operation will automatically start after 3 minutes Check Filter Feature The system starts to log the time once the fan motor operates The check filter light will be lit up only when the accumulated operation time achieves 250 hours or more T
6. from back of unit if using bucket to collect water Check float switch inch length silver tab in top of unit behind bucket to ensure it is not cracked bent broken DEHUMIDIFIER P2 OR dirty or obstructed If bent re adjust by re bending back in place The switch is located on the left side behind BUCKET FULL DISPLAYS the bucket when you are facing the unit Check that unit is level and the filter vents and bucket are thoroughly clean Ensure float is snapped into place inside the bucket and that foam piece is inserted in float See page 7 Fig 2 Unplug unit for at least 5 minutes Plug back in unit Remove and return bucket securely then turn on unit Be sure unit is not too large or too small for the area of the room When first installed run unit on Continuous Mode for 24 hours Allow enough time for unit to remove moisture Set humidity low enough to ensure moisture removal Setting the unit below 45 is not recommended DEHUMIDIFIER NOT Setting may be the same as actual humidity in room thus no moisture to remove DRAWING WATER Be sure all doors windows and other openings are securely closed Be sure unit is level and that there is sufficient air circulation around the unit as well as between unit and floor Make sure unit is level and that there are no curtains blinds or furniture blocking the unit Check that room temperature is 41 F or above If unit is near a heat source such as a clothes dryer etc relocate unit
7. required up to 6 ft to go directly from the unit to floor drain 9 Care And Maintenance Care and cleaning of the dehumidifier Turn the dehumidifier off and remove the plug from the wall outlet before cleaning Clean the Grille and Case Use a cloth dampened with water and a mild detergent Do not use bleach or abrasives Do not splash water directly onto the main unit Doing so may cause an electrical shock cause the insulation to deteriorate or cause the unit to rust The air intake and outlet grilles get soiled easily so use a vacuum attachment or brush to clean Fig 11 Removing the Filter 2 Clean the bucket Every few weeks clean the bucket to prevent growth of mold mildew and bacteria e Remove the bucket and clean it in an area away from the dehumidifier to avoid splashing water onto in the unit e Partially fill the bucket with clean water and add a small amount of mild detergent Swish it around in the bucket empty and rinse NOTE Do not use a dishwasher to clean the bucket After cleaning the bucket it must be securely in place for the dehumidifier to operate 3 Clean the air filter Remove and clean the filter when the filter light illuminates For more frequent use clean the filter more often i e every 2 weeks Remove the filter from the top of the unit See Fig 11 Wash the filter with clean water then dry thoroughly before re inserting the filter CAUTION
8. the control pad will count down the time remaining until start stop The selected time will register for 5 seconds and the system will automatically revert back to display the previous humidity setting When the Auto start and Auto stop times are set within the same program sequence TIMER ON and OFF indicator lights illuminate identifying both ON and OFF times are now programmed You can set the Timer for just ON or just OFF in which case the single corresponding ON or OFF light will be illuminated e Turning the unit ON or OFF at any time or adjusting the timer setting to 0 0 will cancel the Auto Start Stop When LED display window displays the code of P2 the Auto Start Stop function will also be canceled A NOTE ABOUT THE TIMER When you set the timer the unit will only go on once and off once If you want the dehumidifier to cycle on and off repeatedly you do not need to set the timer Instead set your desired humidity and the unit will cycle on and off based on that humidity setting identification Of Parts Front Rear Fig 1b Control Panel Air Filter pull up to remove Air Intake Grill Air Outlet Grill Water Bucket Handle both sides O Drain Hose Outlet O Casters Power Cord amp Plug O Band used only when storing unit NOTE A the pictures in the manual are for explanation purposes only The actual shape of the unit you purchased may be slightly different but the o
9. DO NOT operate the dehumidifier without a filter because dirt and lint will clog the unit and reduce performance 4 Prolonged Periods of Non Use After turning off the unit wait one day before emptying the bucket Clean the main unit water bucket and air filter and let dry completely Wrap the cord and bundle it with the band on the unit See Fig 12 Cover the unit with a plastic bag Store the unit upright in a dry well ventilated place 10 Troubleshooting Tips Before calling for service please review the chart below Possible Solutions Turn off unit and unplug 4 6 hours Plug unit back in Run in normal mode no Turbo fan not on Continuous operation and set humidity level to no AUTO DEFROST more than 5 lower humidity than what the display reads for the room humidity DISPLAYS REPEATEDLY Allow time for the unit to run until it successfully reaches initial humidity setting Lower humidity another 5 and repeat until desired humidity is reached Average setting should be 45 50 Be sure unit humidity is not set too low unit is not sitting on too cold of a floor and unit is not being used in too cold of a room Room should be 41 F or above Be sure there is sufficient air circulation between the unit and the floor FROST APPEARS ON THE COILS This is normal The dehumidifier has an auto defrost feature See page 5 for more information Verify rubber drain plug is not removed
10. ER TO ADJUST HUMIDITY SETTING Possible Solutions Be sure unit is not too large or too small for the area of the room Allow enough time for unit to remove moisture If set on Continuous Mode de select button and set unit to an appropriate humidity setting If humidity in room is above the set humidity then unit will be running Be sure all doors windows and other openings are securely closed Be sure unit is level and that there is sufficient air circulation around the unit as well as between unit and floor Make sure there are no curtains blinds or furniture blocking the unit Lower room temperature If unit is near a source of moisture such as a sink shower washing machine etc then relocate unit Check that filter vents and bucket are thoroughly clean Be sure hose is CLEAN pliable and no longer than 6 feet in length recommended Clear tubing with sizing of 5 8 inch for the outer diameter and 1 2 inch for inner diameter is recommended Hose should be secure on both ends being especially mindful that it is pushed all the way onto connector piece inside unit Hose should exit through the back of unit and always be positioned at a DOWNWARD slope to the desired drain location If using garden hose attached to adaptor piece be sure connection is secure throughout Be sure nothing is obstructing hose connection and there are no kinks or tears in any of the hosing Ensure unit is level and not tilted forward and that buc
11. Indicator Light a l ry Cont High Fan Indicator Light Continuous Operation on Indicator Light gt Timer On Indicator Light Control Pads When you push the button to change operation modes the unit will make a single beep sound to indicate that it is changing modes O Mode Toggle between the following features Normal Utilize this mode if you would like the unit to cycle on and off based on the relative humidity setting you have manually selected See numbers 5 7 and 8 in the column to the right for further instruction In Normal mode both the Comfort and Cont indicator lights will not be illuminated Comfort Utilize this dehumidification feature to automatically control humidity in the 45 55 range based on room temperature When operating in this mode the Up Down amp pads will be deactivated and you will NOT be able to set a desired humidity Continuous Cont Press to activate the continuous dehumidifying operation When operating in this mode the Up Down A pads will be deactivated and you will NOT be able to set a desired humidity The unit will run non stop O Filter The check filter feature is a reminder to clean the Air Filter for more efficient operation The Filter light Clean Filter Indicator Light will illuminate after 250 hours of operation To reset after cleaning the filter press the Filter pad and the light will go off Turbo 3 O Bucket Full Pull Indicator
12. Light O Auto defrost 4 O Auto Defrost Operation Indicator Light Timer Off 7 Indicator Light Fan Control the fan speed Press to select either High or Normal fan speed Set the fan control to High Turbo for maximum moisture removal When the humidity has been reduced and quiet operation is preferred set the fan control to Normal by pressing the Fan button to turn off Turbo mode light Power Press to turn the dehumidifier on and off A V Up Down Pads Humidity Set Control Pads The humidity level can be set within a range of 35 RH Relative Humidity to 85 RH Relative Humidity in 5 increments For drier air press the W pad and set to a lower percent value For damper air press the A pad and set a higher percent value The recommended standard setting is 45 50 You must be on Normal mode to set the humidity Timer Press to initiate the Auto start and Auto stop feature in conjunction with the 4 and W key pads The timer range is 0 0 to 24 hrs Timer does not cycle Display Shows the set humidity level from 35 to 85 or auto start stop time 0 24 while setting then shows the actual 5 accuracy room humidity level in a range of 30 RH Relative Humidity to 90 RH Relative Humidity Control Pad On The Dehumidifier continue Error amp Protection Codes AS Humidity sensor error Unplug the unit for at least 5 minutes and plug it back in If error repeats call Perfect
13. easy access to an electrical outlet Plug the unit into an electrical outlet with a grounding connection Make sure the water bucket is correctly fitted or the unit will not operate properly NOTE Do not attempt to move the dehumidifier when there is water in the bucket The unit may tip over and spill water or damage unit Operating The Unit continueg Removing the collected water 2 options OPTION 1 Use the bucket OPTION 1 Using amp Emptying the Bucket e If the bucket is full when the unit is OFF the unit will beep 8 times the full indicator light will flash and the digital display will show P2 If the bucket is full when the unit is ON the compressor will turn off followed by the fan 30 seconds later The unit will then beep 8 times the full indicator light will flash and the digital display will show P2 Slowly pull out the bucket Grip the left and right handles securely and carefully pull out straight so water does not spill Do not put the tank on the floor because the bottom of the bucket is uneven The bucket will fall and cause the water to spill 1 Pull the bucket 2 Hold both sides of the Throw away the water and replace the bucket The bucket must be in place Amen ee securely for the dehumidifier to operate Do not drink the water The machine will re start when the bucket is restored in its correct position The unit will take 3 minutes to restart 3 Dispose of water replace bucket into proper place
14. ed in the packaging as follows Find the garden hose Find the screws in a pouch inside adapter and short tube the packaging for this manual inside the bucket S o o sa 8 1 Contents This manual provides the information needed for proper use and maintenance of this air conditioner Basic preventative care can help extend the life of this unit The Troubleshooting Tips section in this manual contains a chart with solutions to the most common problems Referring to this section may save time and prevent the need for a service call in the event of a problem Safety Precautions MOY AIM UY A A es se aaa epee ede ee ee rete 3 E A A 4 Electrical Information sli 4 Control Pads On The Dehumidifier As ae em en ee a een ee ee ee 5 Error Protection Codes iii ii a ia 6 Other SAMS cido aia ile aaa 6 Identification of Parts Identification Of parts aria tl siii 7 Removing the collected water Operating The Unit Positioning and ASIN Me Ullastrell ideada 8 Removing the collected water user ee 9 Care and Maintenance Care and cleaning of the ds AUN iia novia a i 10 Troubleshooting Tips Troublesho ting US esse a ii 11 12 NOTE All the illustrations in this manual are for explanation purposes only Unit purchased may be slightly different The design and specifications of the dehumidifier are subject to change without prior notice for product improvement Contact customer service for details
15. he Reset light Clean Filter indicator light flashes one time per second After cleaning the air filter press the Filter pad and the Reset light Clean Filter indicator light goes off Auto Restart If the unit breaks off unexpectedly due to a loss of power it will restart with the previous function setting automatically when the power resumes E1 Unit malfunction Unplug the unit for at least 5 minutes and plug it back in If error repeats call Perfect Aire Consumer Services EC Unit malfunction Make sure the temperature of the working environment is between 41 F 5 C and 95 F 35 C If not please operate the unit under the correct stated temperature If on a concrete floor unplug and elevate unit a few inches off the floor plug back into outlet and power on If you have made these adjustments and still see the EC error code please call Perfect Aire Consumer Services Setting the Timer When the unit is on press the Timer button the Timer Off indicator light illuminates indicating that the Auto Stop program is initiated Press it again and the Time On indicator light illuminates indicating that the Auto Start is initiated If you prefer you can set the timer while the unit is powered off and follow the instructions above to set the unit to go on and then off Press or hold the UP or DOWN pad to change the Auto time by 0 5 hour increments up to 10 hours then at 1 hour increments up to 24 hours The display on
16. hly recommended troubleshoot for any issue in general consists of turning off unit and unplugging for 5 minutes It is also recommended to try another wall outlet 12 are Your Source for Home Comfort Distributed by Perfect Aire LLC 5151 Belt Line Rd Suite 878 Dallas TX 75254 877 3605 6274 www perfectaire us Specification and performance data is subject to change without notice Printed in China
17. into adapter A Fig 10 Then lead the water hose Fig 9 to the floor drain or a suitable drainage facility A hose length of no more than 6 ft is recommended as the hose must allow the water to continuously travel downward into the drain Connector Make sure the hose is secure to avoid leakage Direct the hose down toward the drain making sure that there are no kinks that will stop the water flow Place the end of the hose into the drain and make sure the end of the hose is level or down to let the water flow smoothly Never let drain hose go Fig 10 upward against gravity Rubber plug Place the bucket back in the unit in the proper position The unit will not run if the bucket is not in the proper place Drain tube Female threaded end of water hose connected e Select the desired humidity setting and fan speed on the unit for continuous to Adapter A draining to start Water hose NOTES Continuous mode and continuous draining are different You do not need to be on Continuous mode to do continuous draining See pg 5 for additional NOTE When the continuous drain feature is not being E used remove the drain hose from the outlet and insert information about Continuous mode drain plug Failure to re insert the drain plug will result in To eliminate the use of the drain tube adapter assembly and still drain to the unit malfunction and possible error codes floor you may use tubing 5 8 O D 1 2 1 D in the length
18. ket is pushed in all the way Though the unit may appear level if the surface it sits on is even slightly uneven and the front of the unit is tilted downward continuous draining may not work If necessary slightly prop up the front two wheels of the unit taking care that the unit does not fall backward Check that filter vents and bucket are thoroughly clean If water is going into bucket instead of hose the unit is working properly Please double check all of the above and or un hook hosing set up and start again Make sure the dehumidifer s plug is pushed completely into the outlet Check the fuse circuit breaker box in your home The bucket is full and needs to be emptied The water bucket is not in the proper position Make sure the air filter is clean and not clogged Make sure the unit is upright not tilted and on a flat level surface If you are using the pump operation the unit may be noisy for the first 3 5 minutes after the pump begins operating This is normal Check the hose connection points to make sure they are not loose If collecting water in the bucket make sure continuous drain outlet plug has not been removed from back of unit Make sure the foam piece has not been removed from the float Without this piece the float mechanism will not work properly and the bucket will overflow See page 7 Fig 2 Unit must be powered on Unit cannot be in Continuous mode Unit cannot be in Comfort mode NOTE A hig
19. may reduce performance Place the unit away from the clothes dryer heater or radiator Use the dehumidifier to prevent moisture damage anywhere books or valuables are stored Use the dehumidifier in a basement to help prevent moisture damage The dehumidifier must be operated in an enclosed area to be most effective Close all doors windows and other outside openings to the space that you wish to dehumidify When using the unit Fig 4 16 or more Air outlet grille Air intake en or more Casters At four points on the bottom of unit e Casters can move freely Never force casters to move over carpet or move the unit with water in the bucket The unit may tip over and spill water When first using the dehumidifier operate the unit in Continuous mode for 24 hours NOTE After the first 24 hours should you wish to set a desired humidity you will need to take the unit off of Continuous You will not be able to select a desired humidity while the unit is set on Continuous mode This unit is designed to operate with a working environment between 41 F 5 C and 95 F 35 C If the unit has been switched off and needs to be switched on again quickly allow approximately 3 minutes for the correct operation to resume Do not connect the dehumidifier to a multiple socket outlet that is being used for other electrical appliances Select a suitable location making sure you have
20. perations and functions are the same WHAT IS THE FLOAT DOES IT NEED THE FOAM PIECE INSIDE OF IT Inside the bucket on the left side is an arm mechanism that wobbles This piece is called the float DO NOT remove the foam piece that is found in the plastic holder part of the float See Fig 2 If the piece is removed the bucket will overflow Fig 2 Foam piece inside float mechanism DO NOT REMOVE the foam Accessories Fig 3 Drain Tube 1pc Adapter A 1pc Screws 2pc 88 NOTE Drain tube and adapter are located inside of the water bucket Screws are located in a pouch inside the packaging for this user manual 7 Operating The Unit Positioning the unit A dehumidifier operating in one room will have little or no effect in drying an adjacent enclosed area such as a closet or other room unless there is adequate circulation of air in and out of the area Do not use outdoors This dehumidifier is intended for indoor residential applications only This dehumidifier should not be used for commercial or industrial applications Place the dehumidifier on a smooth level floor strong enough to support the unit with a full bucket of water Allow at least 8 in 20 cm of air space on all sides of the unit for good air circulation Place the unit in an area where the temperature will not fall below 41 F 5 C The coils can become covered with frost at temperatures below 41 F 5 C which
21. ting and fire OSDOo not cover the intake or exhaust openings with cloths or towels A lack of air flow can lead to overheating and fire O Never insert fingers or other foreign objects into grille openings Be sure to warn children of dangers elt may cause electric shock or failure of appliance O Always insert the filters securely Clean filter at least once every two weeks O Operation without filters may cause failure CAUTION SDo not put in places where water may splash onto the unit Water entering unit can degrade the insulation and cause electric shock or fire OCare should be taken when using the unit in a room with the following persons Infants children elderly people and people insensitive to humidity SDo not place heavy objects on the power cord and make sure that the cord is not compressed eThere is danger of fire or electric shock Olf water enters the unit turn unit off disconnect power and contact a qualified service technician eilt may cause failure of appliance and there is danger of electric shock Electrical Information OPlace the unit on a level sturdy section of the floor elf unit falls over it may spill water and damage belongings or cause electrical shock or fire 8Do not use in areas where chemicals are handled This will cause unit deterioration due to chemicals and solvents dissolved in the air OSDo nat climb up on or sit on the
22. unit eYou may be injured if you fall or if the unit falls over ODo not place flower vases or other water containers on top of the unit Water may spill into the inside of the unit causing insulation failure and electrical shock or fire The manufacturer s nameplate is located on the rear panel of the unit and contains electrical and other technical data specific to this unit e Be sure the unit is properly grounded To minimize shock and fire hazards proper grounding is important The power cord is equipped with a three prong grounding plug for protection against shock hazards e Your unit must be used in a properly grounded wall receptacle If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker have a qualified electrician install the proper receptacle Ensure the receptacle is accessible after the unit installation Do not use extension cords or an adapter plug with this unit If it is necessary to use an extension cord use an approved Dehumidifier extension cord only available at most local hardware stores To avoid the possibility of personal injury always disconnect the power supply to the unit before installing and or servicing Control Pads On The Dehumidifier NOTE The control panel of the unit you purchased may be slightly different according to the models Clean Filter Indicator Light z D Filter O Comfort Dehumidifying
23. y from the wall e Otherwise it may cause lt may cause electric shock lt may cause electric shock electric shock or fire due to or fire due to heat or fire excess heat generation generation Mi pawer eord is damaged IPmusthe replaced by a qualified professional ODo not modify power cord SDo nat insert or pull out plug OSDo not place the unit near a length or share the outlet with wet hands heat source with other appliances 6 t may cause electric shock elt may cause electric shock Plastic parts may melt and or fire due to heat cause a fire generation ODisconnect the power if SYou should never try to take OBefore cleaning turn off the strange sounds smells or apart or repair the unit by power and unplug the unit smoke comes from it yourself Failing to do so may cause elt may cause failure of eFailing to do so may cause fire and electric shock machine or electric shock electrical shock or injury ODo not use the unit near SDo not drink or use the ODo not take the water flammable gas combustibles water drained from the unit bucket out during operation such as gasoline benzene thinner etc lt may cause an explosion elt contains contaminants and lt may cause malfunction of or fire could make you sick unit s bucket full feature and cause electrical shock Safety Precautions continued Do not use the unit in small spaces Lack of ventilation can cause overhea
Download Pdf Manuals
Related Search