Ethernet Media Converter WLI-T1-S11G User`s Manual
Contents
1. s WEP Ket settings Upon completion of the setting click Set NOTE To communicate with a wireless LANdevice for which only one encryption WEP Key can be set enter the WEP Key to 1 only 4 When Setting is complete is displayed setting is complete E Setting the access restriction for the setting You can set the restriction to prevent opening the setting page for wireless and wired communications respectively No search is available even from the Ethernet Converter Manager 1 Open the settings page 2 Click Detailed Settings 3 Click Setting Function Access Click Set 4 When Setting is complete is displayed setting is complete E Checking the AirSattion connection status You can check the connection between the PC and the AirStation with the WLI T1 S11G connected 1 Install Ethernet Converter Manager 2 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager Select Edit Search for an AirStation Confirm that the AirStation is indicated in black characters Select File Test Connectio Diagnosis Connection test will be started Wait until Packets sent reaches 100 Results of connection test are displayed NOarow After the connection status and radio signal status are determined the diagnosis results are displayed Satisfactory No problem in total Non Satisfactory Status is unstable When the diagnosis results are2. Internet Options icon 3 Click the Connections tab 4 When the provider information is listed in the Dial up settings area click the O mark on the left side of Never dial a connection below the area to put a dot mark 5 Click LAN Settings in the Local Area Network LAN settings area to confirm the items with a checkmark For memorandum put a checkmark in the U for the same items below Q Automatically detect settings Q Use Automatic configuration script Q Use a proxy server Q Bypass proxy server for local addresses 6 Upon completion of confirming the items with the checkmark remove the checkmark from all the items 1 2 About WEP Encryption Recommendation of encrypted secure systems Since this Ethernet Converter WLI T1 S11G communicates using radio waves radio packets could be intercepted and analyzed outside To ensure transmission security it is recommended to set an encryption key called a WEP Key in the radio packets during communication This product allows for two types of WEP 128 104 bit and 64 40 bit WEP Setting 128 104 bit WEP 13 alphanumeric ASCII characters or 26 hex digits assures higher security However when communicating with a wireless LAN product compatible only with 64 40 bit WEP 5 alphanumeric ASCII characters or 10 hex digits it is neces sary to use 64 40 bit WEP in this product There are two types of encryption keys of 40 bits and 104 bits for WEP Since 24 bit dat
3. Non Satisfactory try the following measures 1 Place the wireless LAN PC closer to the AirStation Be sure to keep a minimum distance of 30cm 2 Change the AirStation location 3 Remove any object between the AirStation and the wireless LAN PC 4 Confirm that there is no electromagnetic interference source such as a microwave oven near the AirStation or wireless LAN PC Communication status indication Excellent Good Poor Bad Signal status indication Excellent Good Poor Bad No Signal E Setting the setting page password Open the setting page Click Detailed Settings Click Password Input a new password into the New Password field and again in the Password confirmation field iN Even is a password is currently set nothing is displayed in the password field of this page Click Set only to change the password If you click Set with this field blank the current password will be deleted For the password you can enter up to eiight alphanumeric characters and the underscore Thes characters are case sensitive If you lost your password you can press the INIT button on the AlrStation to reset it to the default password If the INIT button is used all other settings will be reset to the default factory settings changing the wireless communication mode For more information about the INIT switch see Component names and Functions NOTE If you have set a new password you will be prompted to enter t
4. AUF FALL Ethernet Media Converter WLI T1 S11G User s Manual A Chapter 1 Before using WLI T1 S11G 1 1 Introducing the Ethernet Media Converter WLI TI S11G The WLI T1 S11G is an Ethernet Media Converter that can create a wireless connection for a conventional Ethernet interface PC A network printer and other network devices may also achieve a convenient wireless connection with this product Features of the WLI T1 S11G are e Comply with IEEE802 11b standard realizing 11Mbps wireless communication e Effective range reaches 50m Indoor Case 1 25m indoor case 2 or 160m outdoor under 11Mbps communication Indoor Case 1 Office with few obstructions Indoor Case 1 Office with few obstructions NOTE The effective range is adversely affected by the operating environment Roaming allows you to connect to a network while mobile e 11 wireless channels lightnen network congestion Support for both 128 104 bit and 64 40 bit WEP Refer to About WEP Encryption Recommendation of encrypted secure system P10 NOTE If you want to use 128 104 bit WEP key the access point must support 128 104 bit WEP too You cannot combine 128 104 bit and 64 40 bit WEP in the wireless network e An AirStation access point is required for this product e Connecting a WLI T1 S11G and a hub is not guaranteed for operate correctly E Required Environment OS e Windows XP 2000 ME 98 95 NT4 0 Web Browser e Internet Explorer 4 0 or l
5. Frequency Range Mid Frequency or Television Communications Distance Depending on ambient 25m indoors 50m outdoors at 11Mbps 35m indoors 70m outdoors at 5 5Mbps 40m indoors 90m outdoors at 2Mbps conditions 50m indoors 115m outdoors at 1Mbps Cn Power Current 3W Max 700mA Max consumption Operating 0 C to 40 C 20 to 80 no condensation Temperature Humidity Weight 120g without AC Adapter 58mm x 120mm x 89mm W x D x H LAN Interface
6. S ID area Click Scan to show the AirStation list Select Communication via the AirStation and click OK Set the same WEP as the selected AirStation and click OK AirStation search will start When the selected AirStation is found communication can be made between the WLI T1 S11G and the AirStation 8 Close Ethernet Converter Manager The WLI T1 S11G_ is complete NOOSA The procedure for using your PC as a wireless PC is complete You can use the WLI T1 11G as is You can check the status of the connection with the AirStation by referencing Checking the AirStation connection status on page 9 Step A4 Installing the WLI T1 S11G Upon completion of settings connect the WLI T1 S11G to a network printer Disconnect the LAN cable UTP straight between the PC and the WLI T1 S11G and reconnect the WLI T1 S11G to the network printer Step A5 Verifying the WLI T1 S11G settings Upon completion of WLI T1 S11G installation verify that the WLI T1 S11G is correctly configured 1 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager Ethernet Converter Manager will be activated to automatically begin device searching 2 The setting is correct and complete when the WLI T1 S11G is displayed Click Close to close the Ethernet Converter Manager E Setting from a PC equipped with a wireless LAN board card Execute steps B1 and B2 before connecting the AC adapter to the
7. S11G is complete Click Close to close the Ethernet Converter Manager E Chapter 3 Detailed Setting 3 1 Setting the Communication Environment E Displaying the setting page 1 Install Ethernet Converter Manager by referencing Installing Ethernet Converter Manager on page 5 2 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager Device search will be automatically started NOTE When the WLI t1 s11g is directly connected to the PC s LAN port select Edit Search for an Ethernet Converter to search for the WLI T1 S11G 3 Select the indicated WLI T1 S11G and then select Settings IP Setting Of more than one WLI T1 S11G is displayed specify your WLI T1 S11G by checking the MAC address Enter the IP address of your WLI T1 S11G and click OK Select your WLI T1 S11G with its IP address set and then select Settings WEB Setting 6 When the network password input window appears enter as shown below and click OK User name root Password leave blank default setting If you changed the password be sure to input the correct password 7 The WEB browser opens to display the settings page C1 3 2 Changing and checking the settings E Displaying the setting page Use the following procedure to set the encryption WEP Key in the WLI T1 S11G 1 Open the setting page 2 Click Detailed Settings 3 Select On and enter the WEP Key according to the AirStation
8. WLI T1 S11G Step B1 Installing Ethernet Media Converter Manager Install Ethernet Converter Manager to set the WLI T1 S11G Step B2 Disabling the AirStation WEP The WLI T1 S11G is preset to automatically connect to a nearby as the default setting however no communication can be made if any WEP is set on the AirStation In this case you need to disble the target AirStation WEP By referencing the manual included with the AlrStation open the AirStation configuration screen via the web browser and disable WEP by removing the checkmark from the Use WEP Key box This is a temporary setting and should be reset to use WEP after performing steps B3 and B4 Step B3 Preparing for WLI T1 S11G setup 1 Connect the AC adapter to the WLI T1 S11G 2 The Wireless LED illuminatesfor a few seconds and then goes off lt lt When the Wireless LED blinks immediately after the AC adapter is connected gt gt 1 Press the INIT switch on the WLI T1 S11G only once 2 Confirm that the Wireless LED illuminatesfor a few seconds and then goes off 3 If the AirStation is near the WLI T1 S11G it is automatically connected and the Wireless LED illuminates again lt lt When the Wireless LED does not illuminate gt gt 1 Check that the AirStation operates normally 2 Place the WLI T1 S11G near the AirStation Step B4 Configuring the WLI T1 S11G settings Configuring the WLI T1 S11G settings via the AirStation 1 Select Start Programs AirStation Util
9. a initialization vector is added to these keys during actual communication 40 bit WEP and 104 bit WEP may also be refered to 64 bit WEP and 128 bit WEP Ee Chapter 2 Installing WLI T1 S11G This chapter describes how to make the WLI T1 S11G settings using a Windows PC 2 1 Overview There are two typesof setting methods from the wired or the wireless LAN card on the Windows PC Select the applicable method according to your PC configuration 2 2 Setup Procedure E Setting from a PC equipped with a wired LAN board card Step A1 Preparing for WLI T1 S11G setup 1 Connect the WLI T1 S11G to the PC s LAN port using the included straight cable 2 Connect the AC adapter to the WLI T1 S11G Be sure to use the AC adapter included with this product Step A2 Installing Ethernet Converter Manager 1 Insert the Ethernet Converter CD into the CD ROM drive of the Windows PC The installer will start automatically 2 Click Next 3 Confirm the License Agreement and click Next 4 Confirm the location to install the Ethernet Converter Manager and click Next 5 Confirm that a checkmark is placed for the Ethernet Converter and click Next 6 Click Finish Step A3 Configuring the Ethernet Converter Settings 1 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager 2 Select File Manual Setting 3 Input the ESS ID of the target AirStation into the ES
10. ater e Netscape Navigator 4 0 or later NOTE A Web browser is required when you configure this product from an HTTP interface H Contents of this package WLI T1 S11G AC Adapter International AC Adapters LAN Cable UTP straight Ethernet Converter CD User s Manual this manual Be sure to read additional information on the seperate sheet included with the product Wireless LED Green ON During wireless link Blinking Communicating Ethernet LED ON During wired link Blinking Communicating Front View Diagram Bottom View Diagram INIT Switch Press to initialize the WLI T1 S11G Alternatively each time the switch is pressed the wireless communication mode is changed The current mode can be checked with the wireless LED status immediately after the switch is LAN Port pressed Blinks for a few seconds then goes off Adhoc mode Wireless PCs can communicate with DC Connector each other however communication is not available with wireless LAN PCs Turns on for a few seconds then off Infrastructure mode Communication is available with the AirStation Rear View Diagram D E Checking the browser settings only for making detailed WLI T1 S11G settings Be sure to invalidate the dial up settings and proxy settings under the browser settings The following procedure uses Internet Explorer 5 0 or later for example 1 Select Start Settings Control Panel 2 Double click the
11. he password each time the setting page is opened See Section 3 1 number about inputting the password a E Setting the IP address of the WLI T1 S11G For making detailed WLI T1 S11G settings it is necessary to set the IP address 1 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager Device search will be automatically started NOTE When the WLI t1 s11g is directly connected to the PC s LAN port select Edit Search for an Ethernet Converter to search for the WLI T1 S11G Select the indicated WLI T1 S11G and then select Settings IP Setting Enter the IP address of your WLI T1 S11G and click OK Confirm that the correct IP address is set Click Close to close the Ethernet Converter Manger Enter the IP address of your WLI T1 S11G oR WP Restoring the WLI T1 S11G settings to the default values Open the setting page Click Device Diagnostics Click Reset Click Reset Follow the instructions on the subsequent pageson the computer screen AUN oo Chapter 4 Specifications Product Specifications Wireless LAN Conforming Standards IEEE802 11b Wireless LAN Standard Protocol Interface FCC 15 247 ETS300 328 Data Transfer Method DS SS Simplex Half Duplex 1 2 5 5 11Mbps Auto Sense Infrastructure Mode Adhoc Mode 2 412 to 2 484 MHz No conflict with cell or cordless phones Radio Data Transfer Rate Access Method
12. ity Ethernet Converter Ethernet Converter Manager Ethernet Converter Manager will be activated to automatically begin device searching 2 When the WLI T1 S11G is diplayed select it and click Connect Input the ESS ID of the target AirStation into the ESS ID area Click Scan to show the AirStation list Select Communication via the AirStation and click OK Set the same WEP as the selected AirStation and click OK AirStation search will start An error message is diplayed to indicate Logon failure due to differences in the WEP settings between the WLI T1 S11G and the AirStation Click OK anyway 8 Close Ethernet Converter Manager The WLI T1 S11G is complete w NOOA Step B5 Re enabling the AirStation WEP Re enable the AirSattion WEP disabled in Step B2 Open the AirStation configuration screen via the web browser and enable WEP by insert ing a checkmark in the Use WEP Key box Step B6 Installing the WLI T1 S11G Connect the WLI T1 S11G to shared devices such as the network printer using the LAN cable UTP straight Step B7 Verifying the WLI T1 S11G settings Upon completion of WLI T1 S11G installation verify that the WLI T1 S11G is correctly configured 1 Select Start Programs AirStation Utility Ethernet Converter Ethernet Converter Manager Ethernet Converter Manager will be activated to automatically begin device searching 2 The setting is complete when the WLI T1
Download Pdf Manuals
Related Search