Home

PCM-3336 - Elhvb.com

1. Pin Function Pin Function 1 RED 9 NC 2 GREEN 10 GND 3 BLUE 11 NC 4 NC 12 NC 5 GND 13 HSYNC 6 AGND 14 VSYNC 7 AGND 15 NC 8 AGND 16 NC Chapter 2 Installation 17 Power supply connector CN5 Power supply connector In single board computer non passive backplane applications you will need to connect power directly to the PCM 3336 board using CNS This connector is fully compatible with the standard PC power supply connectors See the following table for its pin assignments Power connector CN5 Pin Function 1 12V 2 GND 3 GND 4 5V Chapter 2 Installation 18 Parallel port PRINTER PORT CN8 Normally the parallel port is used to for connection the PCM 3336 includes an onboard parallel port accessed through PRINTER PORT for data a 26 pin flat cable connector The CPU card comes with an adapter cable which lets you use a traditional DB 25 connector The cable has a 26 pin connector on one end and a DB 25 connector on the other mounted on a retaining bracket Installing the retaining bracket The retaining bracket installs at an empty slot in your system s chassis It provides an external port that allows your parallel peripheral to access data through the card s parallel port connector 1 Find an empty slot in your chassis 2 Unscrew the plate that covers the end of the slot 3 Screw in the bracket in place of the plate 4 Next attach the flat ca
2. CAN CON WO om Nm N O O OD Co Di bo A O V O O N O N GONG N amp OM ON S N i O OKK O 0 N N J p88 27 86 8 85 41 di eee eva DE 84 33 E 85 73 MW ee 1111111 DAL E eve 81 90 FE DD fw Bo o DAOADADADADACADADADADADAG eee ee De VU U U UTU UTU KS A N sol OK O nol NNON col U se U M 10 col Sh eed fo NO eel Ja Ars eof DOC S 00 Lil 6 col 48 26 Es lo o 6 40 91 XE alo 36 07 a 4 o tke 18 v Ti 2 23 19 Gro D e J 11 68 HH H HOHE A X IHI 0 00 Shaa 5 08 OTA N OND 0 eee pa OMR NO 0 O NO 0 OR N Chapter 2 Installation 10 Setting jumpers You configure your card to match the needs of your application by setting jumpers A jumper is the simplest kind of electric switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the c
3. Chapter 3 AMIBIOS Setup 35 Chipset setup options Function option At Bus Clock 14 318 2 PCLK 2 3 PCLK 2 4 PCLK 2 5 PCLK 2 6 PCLK 2 8 PCLK 2 10 PCLK 2 12 Slow Refresh 15 us 60 us 120 us Memory Hole At 15 16M Disabled Enabled RAS Precharge Time 2 5T 1 5T 3 5T RAS Active Time Insert Wait Disabled Enabled CAS Precharge Time Insert Wait Disabled Enabled Memory Write Insert Wait Disabled Enabled Memory Miss Read Insert Wait Disabled Enabled ISA Write Cycle End Insert wait Enable Disabled Enabled I O Recovery Enabled Disabled 36 PCM 3336 User Manual O Recovery Peried 0 us 0 25 us 0 50 us 0 75 us 1 00 us 1 25 us 1 50 us 1 75 us 2 00 us 2 25 us 2 50 us 2 75 us 3 00 us 3 25 us 3 50 us On Chip I O recovery Disabled Enabled 16 Bit ISA Insert Wait Enabled Disabled IDE controller Secondary Chapter 3 AMIBIOS Setup 37 PCI Plug and play setup 38 PCI PnP setup options are displayed by choosing the PCI PnP setup icon from the AMIBIOS setup main All PCI PnP setup options are described in this section AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Confi
4. PCM 3336 3865X 40 PC 104 CPU Module with LCd amp SSD FCC STATEMENT THIS DEVICE COMPLIES WITH PART 15 FCC RULES OPERA TION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFER ENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASON ABLE PROTECTION AGAINTST HARMFUL INTERFER ENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENER ATES USES AND CAN RADIATE RADIO FREQENCY ENERGY AND IF NOTINSTATLLED AND USED IN ACCOR DANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICA TIONS OPERATION OF THIS EQUIPMENT IN A RESIDEN TIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFER ENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EX PENSE Copyright Notice This document is copyrighted 2000 2001 by AAEON Technology Inc All rights are reserved AAEON Technology Inc reserves the right to make improvements to the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of AAEON Technology Inc Information provid
5. 1999 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Standard CMOS setup for changing time date hard disk type etc ESC Exit T Sel F2 F3 Color F10 Save amp Exit Chapter 3 AMIBIOS Setup 47 48 PCM 3336 User Manual CHAPTER SVGA Setup The PCM 3336 features an on board flat panel VGA interface This chapter provides instructions for installing and operating the software drivers on the included display driver diskette Simultaneous display mode The 65545 VGA BIOS supports monochrome LCD EL color TFT and STN LCD flat panel displays It also supports interlaced and non interlaced analog monitors VGA color and VGA monochrome in high resolution modes while maintaining complete IBM VGA compatibility Digital monitors i e MDA CGA and EGA are NOT supported Multiple frequency multisync monitors are supported as analog monitors Both CRT and panel displays can be used simultaneously The PCM 3336 can be set in one of three configurations on a CRT on a flat panel display or on both simultaneously The system is initially set to simultaneous display mode In the utility diskette th
6. Operating temperature 32 to 140 F 0 to 60 C Board size 3 55 L x 3 775 W 90mm x 96mm Weight 0 6 lb 0 25 Kg PCM 3336 User s Manual Board layout T E E TTI Chapter 1 General Information 5 Board dimensions 90 80 84 33 11 34 9 08 0 00 1 27 Oo O N O N Seo bs Ti O N OMON N Do 0 O NIM O ko N N 88 27 JS 85 41 a an E ete mn W er S 9 Doc 00 O N DOC o o Ve 6 DE fi mn folla 38 s BATTERY n DEBE BERLE ORDER Reo ff HONEHMMEENENHEENEHNMENEOEENEONEHONEN ROR ROBO nono i a aa aa a ada a ad eno N 0 00 5 08 OZS N OND O OR OMR N S GINI 0 ON N 6 PCM 3336 User s Manual CHAPTER Installation This chapter explains set up procedures for the PCM 3336 hardware including instructions on setting jumpers and connecting peripherals switches and indicators Be sure to read all safety precautions before you begin the installa tion procedure Jumpers and connectors Connectors on the board link it to external devices such as hard disk drives a keyboard or f
7. v Move to the next field to the right left above or below lt ENTER gt Select the current field Increments a value Decrements a value lt ESC gt Close the current operation and return to the previous level lt PgUp gt Return to the previous page lt PgDn gt Advance to the next page Alphabetic keys A to Z are used in the Virtual keyboard and are not case sensitive Numeric keys 0 to 9 are in the Virtual keyboard and Numeric keypad Chapter 3 AMIBIOS Setup 27 Standard CMOS setup The AMIBIOS Setup options described in this section are selected by choosing the Standard CMOS Setup from the AMIBIOS Setup main menu selection screen as shown below AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time date hard disk type etc ESC Exit Sel F2 F3 Color F10 Save 8 Exit Press enter the Standard CMOS Setup screen appears AMIBIOS SETUP STANDARD CMOS SETUP C 2000 American Megatrends Inc All Rights Reserved Date mm dd yyyy Fri Jul 2000 Base memo
8. 30 PCM 3336 User Manual Quick Boot Set this option to Enabled to instruct AMIBIOS to boot quickly when the computer is powered on This option replaces the old Above 1 MB Memory Test Advanced Setup option Setting Description Disabled AMIBIOS tests all system memory AMIBIOS waits up to 40 seconds for a READY signal from the IDE hard disk drive AMIBIOS waits for 5 seconds after sending a RESET signal to the IDE drive to allow the IDE drive time to get ready again AMIBIOS checks for a lt Del gt key press and runs AMIBIOS Setup if the key has been pressed Enabled AMIBIOS does not test system memory above 1 MB AMIBIOS does not wait up to 40 seconds for a READY signal from the IDE hard disk drive If a READY signal is not received immediately from the IDE drive AMIBIOS does not configure that drive AMIBIOS does not wait for 5 seconds after sending a RESET signal to the IDE drive to allow the IDE drive time to get ready again You cannot run AMIBIOS Setup at system boot because there is no delay for the Hit lt Del gt to run Setup message Boot Up Num Lock Set this option to Off to turn the Num Lock key off when the computer is booted so you can use the arrow keys on both the numeric keypad and the keyboard The settings are On or Off The default setting is On Chapter 3 AMIBIOS Setup 31 Floppy Drive Swap Set this option to Enabled to permit drives A or B to be swapped The settings are Enabled or Disa
9. Installation 23 Floppy drive connector CN10 You can attach up to two floppy disks to the PCM 3336 s on board controller You can use any combination of 514 360 KB and 1 2 MB and or 3 2 720 KB 1 44 MB and 2 88 MB drives The PCM 3336 CPU card comes with a 34 pin daisy chain drive connector cable On one end of the cable is a 34 pin flat cable connector There are two sets of floppy disk drive connectors one in the middle and one on the other end Each set consists of a 34 pin flat cable connector usually used for 3 5 drives and a printed circuit board connector usually used for 5 25 drives Connecting the floppy drive 1 Plug the 34 pin flat cable connector into the floppy disk connector 2 Attach the appropriate connector on the other end of the cable to the floppy drive s You can use only one connector in the set The set on the end after the twist in the cable connects to the A floppy The set in the middle connects to the B floppy Chapter 2 Installation 24 Pin assignments The following table lists the pin assignments for the floppy disk connector 2 34 0000000000 0000000 0900000 0000000000000 1 33 FLOPPY DISK Connector FLOPPY CON CN10 Pin Signal Pin Signal 1 33 odd GND 2 DENSEL 4 6 UC 8 INDEX 10 MTRA 12 DRVB 14 DRVA 16 MTRB 18 DIR 20 STEP 22 WDATA 24 WGATE 26 TKO 28 WPT 30 RDATA 32 SIDE1 34 DSKCHG Chapter 2 Installation 25 Chapter 2 I
10. Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Save Settings and Exit Exit Without Saving Write the current settings to CMOS and exit ESC Exit V Sel F2 F3 Color F10 Save 8 Exit Chapter 3 AMIBIOS Setup 45 Save settings and exit If you select this option and press lt Enter gt the values entered in the setup utilities will be recorded in the chipse s CMOS memory The microprocessor will check this every time you turn your system on and compare this to what it finds as it checks the system This record is required for the system to operate AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Exit without saving the current settings ESC Exit V Sel F2 F3 Color F10 Save amp Exit 46 PCM 3336 User Manual Exit without saving Selecting this option and pressing lt Enter gt lets you exit the Setup program without recording any new values or changing old ones AMIBIOS SETUP BIOS SETUP UTILITIES C
11. The instructions in this manual assume that you understand elementary concepts of MS DOS and the IBM Personal Comput er Before you attempt to install any driver or utility you should know how to copy files from a floppy disk to a directory on the hard disk understand the MS DOS directory structure and know how to format a floppy disk If you are uncertain about any of these concepts please refer to the DOS or Windows user reference guides for more information before you proceed with the installation Before you begin Before you begin installing software drivers you should make a backup copy of the display driver diskette and store the original in a safe place The display driver diskette contains drivers for several versions of certain applications You must install the correct version in order for the driver to work properly so make sure you know which version of the application you have 52 PCM 3336 User s Manual Windows setup These drivers are designed to work with Microsoft Windows 3 1 You may install these drivers through Windows or in DOS Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it is working correctly Step 2 Place the display driver diskette in drive A In Windows Program Manager choose File from the Options Menu Then from the pull down menu choose Run At the command line prompt type A WINSETUP Press the lt ENTER gt key or click OK to begin the installa
12. User s Manual VGA drivers and utilities 1 8 pin 4 x 2 pin header for KB amp PS 2 mouse e 1 Hard disk drive IDE interface cable 44 pins 1 Floppy disk drive interface cable 34 pins 1 SVGA adapter 16 pins 1 parallel port adapter 26 pins 2 Serial port adapters 10 pins 1 bag of screws and miscellaneous parts If any of these items are missing or damaged contact your distribu tor or sales representative immediately Notice Dear Customer Thank you for purchasing the PCM 3336 board The user manual is designed to help you to get the most out of the PCM 3336 please read it thoroughly before you install and use the board This product that you have purchased comes with a two years limited warranty AAEON will not be responsible for any misuse of the product Therefore we strongly urge that user first read the manual before using the product To receive the lastest version of the user manual please visit our Web site at Taiwan www aaeon com tw U S A www aaeon com Contents General Information 1 Introduction lt isssesaassssassatvaa saan saa ara aa dveveassaiesesesdstesoasvoassoes 2 SD CITICATIONS iiscaissecccinceccsvarsevecedocnccedsosecesseaesssukedestessdeccsnssesdue 3 Board layout ccsseact coseacs aa wa pa ENT Saanaa Nanna cenare 5 Board dimensions 6 s Osa Agengan naa ag et aa ag Ee 7 Jumpers
13. and connectors 8 Board Layout ssccsdssscstsscdessconsiossesssccssoecssnessecscsavecesasaseonsseceeses 9 Setting jumpers 10 Safety Precautions 11 IDE hard drive connections HDD CON CN1 12 Connecting the hard drive ii 12 Keyboard connector PS2 KB CN2 14 Display connector VGA CON FLAT PANEL CON CN4 CN6 x aa a aa secs a avi 15 Power supply connector CN55 17 Parallel port PRINTER PORT CN 9 5 18 Serial ports COM1 CN9 COM2 CNI11 20 Reset switch RST SW J2 ii 21 HDD LED HD LED J1 mens 21 Clear CMOS CLEAR CMOS J7 oosessesosssssensssseessssereessene 21 LCD Power Select J4 ii 22 LCD Panel Shift C10CK I8 nn 22 Floppy drive connector CNI10 23 Connecting the floppy drive 23 AMIBIOS Setup 26 General information 27 Starting AMIBIOS setup e ae Unen nenen 27 AMIBIOS main menu i 27 Using a mouse with AMBIOS setup 28 Using the keyboard with AMIB
14. 0 2004 O 0 200 ell 0 200 3 350 Y 0 3 550 PC 104 module dimensions inches 5 68 PCM 3336 User s Manual APPENDIX LCD Display BIOS Configuration This appendix gives instructions for configuring various LCD displays Configuring various LCD display Follow the instructions below to integrate an LCD VGA BIOS into the PCM 3336 system BIOS 1 Combine the VGA BIOS with the system BIOS following the instructions at the DOS prompt DEBUG N SBC 355 ROM L 4000 0 N lt VGABIOS DAT gt L 4000 0 R CX CX 2000 0 R BX BX 0000 12 N lt Newfile ROM gt W 4000 0 Q DOS utility program lt ENTER gt lt ENTER gt lt ENTER gt Read STN DAT in BIOS files for example lt ENTER gt lt ENTER gt lt ENTER gt lt ENTER gt lt ENTER gt lt ENTER gt Assign new file name to new SBC 355V BIOS lt ENTER gt Write the BIOS back to disk lt ENTER gt 2 Use the utility program AMIFLASH COM to write the system BIOS file you just created to the BIOS chip on board AMIFLASH lt Newfile ROM gt 70 PCM 3336 User s Manual
15. 2 O 16 33 SAI 34 NC 35 SAO 36 SA2 37 HDCSO 38 HDCS1 39 ACT 40 GND 41 VCC 42 VCC 43 GND 44 NC Chapter 2 Installation 14 Keyboard connector PS2 KB CN2 The PCM 3336 provides a 8 pin header for KB amp PS 2 connection 2 6 O O o O 0 0 o 1 7 Keyboard connector PS2 KB CN2 Pin Function KBDATA KBCLOCK KGND KVcc MSDATA MSCLOCK GND N OJO By Go Po Chapter 2 Installation 15 Display connector VGA CON FLAT PANEL CON CN4 CN6 The PCM 3336 CPU card s SVGA connector VGA CON with PCI bus supports monochrome display as well as high resolution color displays The card also features an LCD connector FLAT PANEL CON which allows you to connect various flat panel displays The following table lists their pin assignments 2 44 o 00 O I IS OI I 00000000000000 1 43 LCD connector FLAT PANEL CON CN6 Pin Function Pin Function 1 12 Voc 2 12 Vi 3 GND 4 GND 5 LCDV 6 LCDV 7 FPVEE 8 GND 9 PO 10 P1 11 P2 12 P3 13 P4 14 P5 15 P6 16 P7 17 P8 18 P9 19 P10 20 P11 21 P12 22 P13 23 P14 24 P15 25 P16 26 P17 27 P18 28 P19 29 P20 30 P21 31 P22 32 P23 33 GND 34 GND 35 LCD clock SHCLK 36 FLM V SYS 37 ACDCLK M 38 LP H SYS 39 GND 40 ENABKL 41 GND 42 ASHCLK 43 GND 44 GND Chapter 2 Installation 16 00000000 00000000 SVGA connector VGA CON CN4
16. 5 from the previous page Besides the special display drivers marked by an asterisk you should be able to use the following standard drivers VGA 640x480 16 colors Super VGA 800x600 16 colors 54 PCM 3336 User s Manual Panning Drivers Special panning drivers are provided to allow high resolution modes to be displayed on a flat panel or CRT These drivers will show a section of a larger screen and will automatically pan or scroll the screen horizontally and vertically when the mouse reaches the edge of the display Linear Acceleration Drivers A special high performance linear acceleration driver is provided for 256 color modes This driver may require special hardware and may not be supported on all systems It is only available for Windows3 1 Chapter 4 SVGA Setup 55 AutoCAD R12 These drivers are designed to work with Autodesk AutoCAD R12 They conform to the Autodesk Device Interface ADJ for Rendering drivers and Display drivers These display list drivers accelerate redraw pan and zoom functions Driver installation Step 1 Place the display driver diskette in drive A Type A lt ENTER gt to make this the default drive Type SETUP lt ENTER gt to run the SETUP program Press any key to get to the applica tions list Using the arrow keys select AutoCAD Release 12 and press lt ENTER gt This will display a list of supported driver resolutions Using the arrow keys and the lt ENTER gt key select the resolut
17. 640 PC 104 4 port RS 232 Module PCM 3660 PC 104 Ethernet Module e PCM 3718H 30 KHz A D Module e PCM 3724 48 channel DIO Module PCM 3840 DiskOnChip 2000 Flash disk Module lt PCM P50 PC 104 Vehicle Power Supply Module Installing these modules on the PCM 3336 is a quick and simple operation The following steps indicate how to mount the PC 104 modules Stepl Step2 Step3 Remove the PCM 3336 from your system paying particular attention to the safety instructions already mentioned above Make any jumper or link changes required to the CPU card now Once the PC 104 module is mounted you may have difficulty in accessing these Normal PC 104 modules have male connectors and mount directly onto the main card Please refer to the PC 104 module mounting diagram on the following page After this is in place you have the correct mounting connector to accept your PC 104 module 66 PCM 3336 User s Manual Step4 Mount the PC 104 module onto the CPU card Do this by pressing the module firmly but carefully onto the mounting connectors Step5 Secure the PC 104 module onto the CPU card using the four mounting spacers and screws PC 104 Mounting Support Male gt PCM 3336 CPU Card PC 104 Module PC 104 Module Mounting Diagram Appendix A Installing PC 104 Modules 67 3 500 3 250 3 775 3 57554 3 575 0 0000000000000000000
18. BIN or C UTILS After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS Step 2 To install the VESA driver type either VESA lt ENTER gt or VESA lt ENTER gt at the DOS prompt The optional command line parameter enables all of the available modes Make sure that your monitor is capable of displaying these high resolu tion modes before enabling them NOTE If the video BIOS already supports VBE extended video modes DO NOT use this driver Run the VTEST EXE program to see if the video BIOS supports the VBE modes 60 PCM 3336 User s Manual Word These drivers are designed to work with Microsoft Word 5 0 and 5 5 Driver installation If you have already installed Word on your computer go to Step 2 to install the new video driver Step 1 Install Word as normal Step 2 After you complete the Word installation place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applica tions Use the arrow keys to select Word and press lt ENTER gt Use the arrow keys to select the desired screen resolution and press lt ENTER gt make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displaye
19. IOS setup nean 28 Standard Setup issccscccccsessesocnssenscesscssnneisonsssatacssecsasencsatecssetsevs 29 Advanced Setup 31 Advanced chipset Setup 36 PCI Plug and play setup 39 Peripheral setip asesenengan sag ana NGENE gana DTT Sona vsv ssve tsss 42 Change supervisor password 44 Auto configuration with optimal settings se 45 Auto configuration with fail safe settings 46 Save settings and exil 47 Exit without saving 48 SVGA SOUDE nest et 50 Simultaneous display mode 51 Sleep MOG sisscsscccccsccsvsscssonssseedevscesdbedcenstessvaedsebesoasesecsecesneees 51 Software SUPPOTt cccccsssssssssssssscssssssssscsssscssssssssssssssscssssees 52 Driver Installation cvs cscisceecccoeuseescesdssonssseoctessnstssecssesesscossesse 53 Windows setup San ule ees a a e vu 54 AUTOCAD R 2 3 8 KIN INN cede TA 57 Lotus 1 2 3 and Lotus Symphony 59 NESS AT 43 Nord AASIA oe A eS May a ua 61 WordPert Gts2 ua z i sete asa ni 62 Installing PC 104 Modules 66 Installing PC 104 mod
20. IRQ from the pool of available IRQs passed to BIOS configurable devices The available IRQ pool is determined by reading the ESCD NVRAM If more IRQs must be removed from the pool the end user can use these PnP Setup options to remove the IRO by assigning the option to the ISA setting Onboard I O is config urable by AMIBIOS The IRQs used by onboard I O are config urable by AMIBIOS The IRQs used by onboard I O are config ured as PnP The settings are PnP or ISA The default settings are PnP Chapter 3 AMIBIOS Setup 39 40 Standby mode timeout This sets the period of system inactivity after which the system goes into Standby mode the intermediate power saving state The settings range from 10 seconds to 2 hours and can be set manually when power management is in SMI The default setting is Dis abled When the system goes into power saving mode power management will skip to the next mode in the sequence if this is disabled Suspend mode timeout This sets the period of system inactivity after which the system goes into Suspend mode the maximum power saving state The settings range from 10 seconds to 2 hours and can be set manually when power management is in SMI The default setting is Dis abled When the system goes into power saving mode power management will skip to the next mode in the sequence if this is disabled PCM 3336 User Manual Peripheral Setup Peripheral Setup options are displayed by choosing the Periph
21. ated Device Electronics hard disk drives to the PCM 3336 s internal controller The card comes with a 40 pin flat cable Connecting the hard drive Wire number 1 on the cable is red or blue and the other wires are gray 1 Connect one end of the cable to the IDE connector Make sure that the red or blue wire corresponds to pin 1 on the connec tor which is labeled on the board on the right side 2 Plug the other end of the cable to the Enhanced IDE hard drive with pin on the cable corresponding to pin 1 on the hard drive See your hard drive s documentation for the location of the connector Unlike floppy drives you can make the connections with any of the connectors on the cable If you install two drives you will need to set one as the master and one as the slave You do this using jumpers on the drives If you install just one drive set it as the master 2 44 S I S S S S 000000000 00000 0000000000000000000000 1 43 Chapter 2 Installation 13 Pin assignments The following table lists the pin numbers and their respective signals IDE Connector HARD DISK Driver CON CN1 Pin Signal Pin Signal 1 Reset 2 GND 3 HD7 4 HD8 5 HD6 6 HD9 7 HD5 8 HD10 9 HD4 10 HD11 11 HD3 12 HD12 13 HD2 14 HD13 15 HD1 16 HD14 17 HDO 18 HD15 19 GND 20 NC 21 NC 22 GND 23 IOW 24 GND 25 IOR 26 GND 27 IORDY 28 BALE 29 VCC 30 GND 31 IRQ14 3
22. ble connector to PRINTER PORT Wire 1 of the cable is red or blue and the other wires are gray Make sure that Wire 1 connects to Pin 1 of PRINTER PORT Pin 1 is on the right side of PRINTER PORT Chapter 2 Installation 19 2 26 0000000000000 00000 00 000000 1 25 Pin assignments PRINTER Connector PRINTER PORT CN8 Pin Signal Pin Signal 1 Strobe 2 RAF 3 PDO 4 PERR 5 PD1 6 PINIT 7 PD2 8 PSLIN 9 PD3 10 GND 11 PD4 12 GND 13 PD5 14 GND 15 PD6 16 GND 17 PD7 18 GND 19 PACK 20 GND 21 PBUSY 22 GND 23 PPE 24 GND 25 PSEL 26 NC Chapter 2 Installation 20 Serial ports COM1 CN9 COM2 CN11 The PCM 3336 offers two serial ports RS 232 These ports let you connect to serial devices a mouse printers etc or a communica tion network N o oo oo oo oo wo OO COM1 connector CN9 Pin Signal DLSD1 SIN1 TxD 1 DTR1 GND DSR 1 RTS 1 CTS 1 RI 1 0 NC 0 CO NI D Oo AR O N COM2 connector CN11 Pin Signal RLSD2 485Tx SIN2 485 TX TXD2 422 Rx DTR2 422 Rx GND DSR 2 RTS 2 CTS 2 RI 2 0 NC O CO NI O 01 B P Chapter 2 Installation 21 Reset switch RST SW 2 You can connect an external switch to easily reset your computer This switch restarts your computer as if you had turned off the power then turned it back on The following ta
23. ble shows the pin assignments for the RST SW Reset switch RST SW 2 Pin Function 1 Reset 2 GND HDD LED HD LED 1 You can connect a LED to indicate that an IDE device is in use The pin assignments for this jumper are as follows HDD LED pin assignments HD LED 1 Pin Function 1 R W IDE 2 Pull high Clear CMOS CLEAR CMOS J 7 You can use J7 to clear the CMOS data if necessary to reset the CMOS data place a jumper cap on J7 pin 1 2 for just a few second and then remove the jumper cap to J7 pin 2 3 Clear CMOS CLEAR CMOS 7 Clear CMOS Normal 1 2 3 1 2 3 9 0 O 00 Chapter 2 Installation 22 LCD Power Select J 4 You can use J4 jumper to select the voltage setting for the LCD power To select a certain voltage level close the corresponding pin numbers with a pin cap Pin 1 2 will provide 5 volt of power and pins 2 3 will provide 3 3 volt of power LCD Power Select J 4 5 V 3 3 V 123 123 9 0 O e e default Shift Clock Select J 8 J8 jumper is designated for the LCD monitor a specified setting should be provided in your manufacturer manual Shfclk is the raising edge setting and the falling edge setting is the AShfclk By using this jumper the enhancement of the monitor can be effected Shift Clock Select Shfclk AShfclk 12 3 Coe S default Chapter 2
24. bled The default setting is Disabled PS 2 Mouse Support When this option is set to Enabled AMIBIOS supports a PS 2 type mouse The settings are Enabled or Disabled The default setting is Enabled System Keyboard This option specifies that a keyboard is attached to the computer The settings are Present or Absent The default setting is Present Primary Display This option specifies the type of display monitor and adapter in the computer The settings are Mono CGA40x25 CGA80x25 VGA EGA or Absent The default setting is EGA VGA Display Device This option allows user to select the display device The settings are CRT LCD and Both The default setting is Both 32 PCM 3336 User Manual LCD type This option allows the user to select the LCD type The PCM 3336 supports the following LCD types Brand 640x480 16bit Color DSTN TFT LM64C08P 640x480 8bit Dual Scan Mono STN LM64P 11 640x480 8bit Dual Scan EL LJ64H052 800x600 18bit Color TFT NL8060AC26 11 640x480 4 bit PLASMA PG6404SORM16 3 Password Check This option enables password checking every time the computer is powered on or every time AMIBIOS Setup is executed If A ways is chosen a user password prompt appears every time the computer is turned on If Setup is chosen the password prompt appears as AMIBIOS is executed The default is Setup Wait for F1 if Error AMIBIOS POST error messages are followed by Press lt F1 gt to continue If this optio
25. ctions CPU ALi M6117C Intel 80386SX 40 compatible CPU type Onboard SQFP Bus interface PC 104 bus BIOS AMI 128KB FLASH BIOS Chipset ALi M6117C I O Chipset ITE8661F Memory Onboard 4 Mbytes Fast Page DRAM Enhanced IDE Supports up to two IDE devices FDD interface Supports up to two floppy disk drives 5 25 360KB and 1 2MB and or 3 5 720KB 1 44MB and 2 88MB Parallel port One bi directional parallel port Supports SPP ECP and EPP modes Serial port One RS 232 and one RS 232 422 485 serial ports Ports can be configured as COM1 COM2 COM3 COM4 or disabled individually 16C550 equivalent KB Mouse connector 8 pin 4 x 2 pin header connector supports PC AT keyboard and PS 2 mouse Battery Lithium battery for data retention Watchdog timer Can generate a system reset IRO15 or NMI Software selectable time out interval 30 5 us 512 sec 30 5 us step DMA 7 DMA channels 8237 equivalent Interrupt 15 interrupt levels 8259 equivalent Flat Panel CRT Interface Chipset C amp T 65545 Display memory Onboard 1 MB display memory Display type Supports non interlaced CRT and LCD TFT DSTN and MONO displays Can display both CRT and Flat Panel simultaneously Resolution Up to 800x600 256 colors Chapter 1 General Information 3 4 SSD Interface One 32 pin DIP socket supports M Systems DiskOnChip 2000 series up to 288MB Mechanical and Environmental Power supply voltage 5V 4 75V to 5 25V
26. d Use the backspace key to erase this and type in your Word directory After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS Step 3 Copy the driver file for the desired resolution that was just installed to SCREEN VID Chapter 4 SVGA Setup 61 WordPerfect These drivers are designed to work with WordPerfect 5 0 or 5 1 They support 132 column display in editing mode and high resolution graphics display in PreView mode Driver installation Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applications Use the arrow keys to select WordPerfect and press lt ENTER gt A list of supported screen resolutions will be displayed Use the arrow keys to select the desired screen resolution and press lt ENTER gt make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displayed Use the backspace key to erase this default and type in the WordPerfect directory At this point you may be asked to create the target directory if it does not already exist After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exi
27. ed in this manual is intended to be accurate and reliable However AAEON Technology Inc assumes no responsibility for its use nor for any infringements upon the rights of third parties which may result from its use Acknowledgements ALI is a trademark of Acer Laboratories Inc AMI is a trademark of American Megatrends Inc Cyrix is a trademark of Cyrix Corporation IBM PC AT PS 2 and VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp Part No 2047333602 3rd Edition Printed in Taiwan Nov 2000 A Message to the Customer AAEON Customer Services Each and every AAEON product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments Whether your new AAEON equipment is destined for the laboratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name AAEON has come to be known Your satisfaction is our primary concern Here is a guide to AAEON s customer services To ensure you get the full benefit of our services please follow the instructions below carefully Technical Support We want you to get the maximum performance from your products So if you run into technical difficulties we are here to help For the m
28. eral Setup icon from the AMIBIOS Setup main menu All Peripheral Setup options are described in this section AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Configure peripheral feautres ESC Exit T Sel F2 F3 Color F10 Save 8 Exit AMIBIOS SETUP PERIPHERAL SETUP C 2000 American Megatrends Inc All Rights Reserved Available Options Onboard Serial Port 1 Auto Disabled Onboard Serial Port 2 Auto Enabled Onboard Ir Port Disable Onboard Ir Mode HPSIR Onboard Ir Duplex Half Onboard Parallel Port Auto Onboard Parallel Port Mode Normal ESC Exit V Sel Onboard Parallel Port IRQ Auto PgUp PgDn Modify Onboard Port DMA Channel N A F2 F3 Color Onboard Parallel Port This option enables the parallel port on the motherboard and specifies the parallel port base I O port address The settings are Disabled 278 378 and 3BC The default setting is Enabled Parallel Port Mode This option specifies the parallel port mode ECP and EPP are both bidirectional data transfer sechemes that adhere to the IEEE P1284 specification The set
29. ere are three COM files which can be used to select the display Simply type the filename at the DOS prompt CT COM Enables CRT display only FPCOM Enables panel display only SM COM Enables both displays at the same time Sleep mode 50 The display driver diskette contains two files that support sleep mode Simply type the filename at the DOS prompt ON COM switches to normal display mode OFF COM switches to sleep mode PCM 3336 User s Manual Software support The drivers support the following applications using the filenames and resolutions listed Application Filename Resolution Colors Windows 3 1 LINEAR4 DRV 640x480 16 800x600 16 1024x768 16 LINEAR8 DRV 640x480 256 800x600 256 1024x768 256 LINEAR16 DRV 640x480 64K LINEAR24 DRV 640x480 16M AutoCAD R12 RCTURBOC EXP 640x480 16 800x600 16 1024x768 16 640x480 256 800x600 256 1024x768 256 640x480 32K 640x480 64K 640x480 16M Lotus 1 2 3 2 0 and Lotus Symphony 1 0 1 1 V132X25 DRV 132x25 Text 16 V132X50 DRV 132x50 Text 16 VESA 1 2 VESA COM 800x600 16 1024x768 16 640x400 256 640x480 256 800x600 256 1024x768 256 640x480 32K 640x480 64K Chapter 4 SVGA Setup 51 Word 5 0 VGA600 VID 800x600 16 VGA768 VID 1024x768 16 Word 5 5 VGA55600 VID 800x600 16 VGA55768 VID 1024x768 16 WordPerfect 5 0 CHIPS600 WPD 800x600 16 CHIPS768 WPD 1024x768 16 WordPerfect 5 1 VGA600 VRS 800x600 16 VGA768 VRS 1024x768 16 Driver installation Necessary prerequisites
30. guration with Fail Safe Settings Save Settings and Exit Exit Without Saving Configure PCI Plug and Play features ESC Exit Sel F2 F3 Color F10 Save 8 Exit Plug and Play Aware OS Set this option to Yes if the operAZting system installed in the computer is Plug and Play aware AMIBIOS only detects and enables PnP ISA adapter cards that Are required for system boot The Windows 95 operating systems detects and enables all other PnP aware adapter cards Set this option to No if the operating system such as DOS OS 2 Windows 3 x does not use PnP You must set this option correctly or PnP aware adapter cards installed in your computer will not be configured properly The settings are Yes or No default settings is no PCM 3336 User Manual AMIBIOS SETUP PCI PLUG AND PLAY SETUP C 2000 American Megatrends Inc All Rights Reserved Available Options DMA Channel 0 Enabled PnP No DMA Channel 1 PnP Yes DMA Channel 3 PnP DMA Channel 5 PnP DMA Channel 6 PnP DMA Channel 7 PnP IRQ3 PnP IRQ4 PnP IRQ5 PnP IRQ7 PnP IRQ9 PnP IRQ10 PnP IRQ11 PnP ESC Exit J1 Sel IRQ14 PnP PgUp PgDn Modify IRQ15 PnP F1 Help F2 F3 Color IRG3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 These options specify bus that the named interrupt request lines IRQs are sued on These options allow you to specify IRQs for use by legacy ISA adapter cards These options determine if AMIBIOS should remove an
31. he Advanced CMOS Setup icon from the AMIBIOS Setup main menu to enter Advanced CMOS setup The Advanced CMOS Setup options described in this section are the standard options as shown on the following screen AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Advanced CMOS setup for configuring system options ESC Exit f9 Sel F2 F3 Color F10 Save 8 Exit Press enter the Advanced CMOS Setup screen appears AMIBIOS SETUP ADVANCED CMOS SETUP C 2000 American Megatrends Inc All Rights Reserved Quick Boot Disabled Available Options 1st Boot Device IDE 0 Disabled 2nd Boot Device Floppy Enabled 3rd Boot Device Disable Try Other Boot devices Yes BootUp Num Lock Disable Floppy Drive Swap Disabled Floppy Drive Seek On PS 2 mouse Support Enabled System Keyboard Enable Primary Display VGA EGA Display Device Both LCD Type 640 18BTFT 1 Password Check Setup Wait For F1 if error Enabled C000 32k Shadow Disabled C800 32k Shadow Disabled ESC Exit T Sel D000 32k Shadow Disabled PgUp PgDn Modify D800 32k Shadow Disabled F2 F3 Color
32. ions that are appropriate for your monitor When all of the desired resolutions have been selected press lt END gt to begin the installation At this point you will be asked for a drive and directory to copy the driver files Enter the drive and directory that contains the installed AutoCAD R12 If the destination directory does not exist you will be asked for confirmation When the installation is complete press any key to continue Press lt ESC gt followed by Y to exit to DOS Step 2 Go to the AutoCAD directory where the new drivers were installed and run the driver installation program by typing ACAD12 r lt ENTER gt This program will configure your AutoCAD R12 to use the new display drivers Select TurboDLD Classic Configuring TurboDLD Select Configure Video Display In Display Device Configuration choose Select Graphics Board Resolution Then choose Select Display Graphics Board After choosing a graphics board go to Select Display Resolution After selecting the display resolution save the new configuration and return to the main menu 56 PCM 3336 User s Manual Basic Configuration Menu This menu allows you to modify Number of AutoCAD Command Lines Font Size 6x8 8x8 8x 14 8x 16 12x20 12x24 Dual Screen Enable Disable User Interface Configuration Double Click Interval Time BP Button BP Highlight Patt Line Xor Rect Both BP Refresh Enable Disable BP Cache Enable Disable Expert Configuration Menu This menu al
33. is working correctly Then exit Windows Step 2 Place the display driver diskette in drive A Type A lt ENTER gt to make this the default drive Type SETUP lt ENTER gt to run the driver SETUP program Press any key to get to the applications list Using the arrow keys select Windows Version 3 1 and press the lt ENTER gt key Press the lt ENTER gt key to select All Resolutions and then press lt END gt to begin the installation At this point you will be asked for the path to your Windows System directory default C WINDOWS When the installation 1s complete press any key to continue Press lt ESC gt followed by Y to exit to DOS Step 3 Change to the directory where you installed Windows usually C WINDOWS Step 4 Type SETUP lt ENTER gt to run the Windows Setup program It will show the current Windows configuration Use the up arrow key to move to the Display line and press lt ENTER gt A list of display drivers will be shown Use the arrow keys to select one of the drivers starting with an asterisk and press lt EN TER gt Step 5 Follow the directions on the screen to complete the setup In most cases you may press lt ENTER gt to accept the suggested option When Setup is done it will return to DOS Type WIN lt ENTER gt to start Windows with the new display driver Changing Display Drivers in DOS To change display drivers from DOS change to the Windows directory and run Setup repeating steps 4 and
34. lip To open a jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either pins 1 and 2 or 2 and 3 Open Closed Closed 2 3 The jumper settings are schematically depicted in this manual as follows D 2073 00 ce 0 00 Open Closed Closed 2 3 A pair of needle nose pliers may be helpful when working with jumpers If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representa tive before you make any changes Generally you simply need a standard cable to make most connec tions Chapter 2 Installation 11 Safety precautions Warning Always completely disconnect the power cord from Caution your chassis whenever you are working on it Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power Only experienced electronics personnel should open the PC chassis Always ground yourself to remove any static charge before touching the CPU card Modern electronic devices are very sensitive to static electric charges Use a grounding wrist strap at all times Place all electronic components on a static dissipative surface or in a static shielded bag when they are not in the chassis Chapter 2 Installation 12 IDE hard drive connector HDD CON CN1 You can attach two Enhanced Integr
35. loppy drives In addition the board has a number of jumpers that allow you to configure your system to suit your application The table below lists the function of each of the board jumpers and connectors Jumpers and connectors Number Function J1 HDD LED J2 Reset Switch J3 DOC Address Setting J4 LCD Power Select J5 COM2 RS 232 422 485 select J6 COM2 RS 232 422 485 select for Data In J7 Clear CMOS J8 LCD Panel Shift Clock Select Number Function CN1 HDD connector CN2 KB PS2 connector CN3 PC104 connector CN4 SVGA connector CN5 Power connector CN6 LCD connector CN7 PC104 connector CN8 Printer connector CN9 COM1 connector CN10 Floppy disk connector CN11 COM2 connector Chapter 2 Installation 8 Board Layout co 0 Z Z O O s s sns 1 AMAA OA NAAA a Ca a ah TTYTTTTITIT 6 O Doc LAMINA AMA Se E k ge B od E ooo x J7 QI INFN KI HIHIKIKI HI TANTA OF O TA TE FE HHH EE EU EU EEE KHHOHEOHMKHEHE FEE ZI EO apa jaja TTO ET TI HART HI s at ons al PC 104 CONNECTOR Chapter 2 Installation 9 Mechanical Drawing
36. lows you to modify Display List Enable Disable Drawing Cache Enable Disable Use Acad 31 bit space Yes No Internal Command Echo Enable Disable BP Zoom Mode Freeze Float Regen Mode Incremental Fast If your previously installed driver is not TurboDLD you will have to reconfigure the RENDER command the first time you use it Chapter 4 SVGA Setup 57 Lotus 1 2 3 and Lotus Symphony These drivers are designed to work with Lotus 1 2 3 versions 2 0 2 01 and 2 2 and with Lotus Symphony versions 1 0 and 1 1 Driver installation Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applications Use the arrow keys to select Lotus Symphony and press lt ENTER gt A list of supported screen resolutions will be displayed Use the arrow keys to select the desired screen resolution and press lt ENTER gt Make sure your monitor is able to display the resolution desired Press lt END gt to begin the driver installation process A default drive and directory path will be displayed Use the backspace key to erase this default and type in the 123 directory At this point you may be asked to create the target directory if it does not already exist After the files have been installed press any key to return to the list of supported applications Press lt ESC gt followed by Y to exit to DOS C
37. lso coordinates communications between the conventional ISA bus and the PCI bus It must be stated that these items should never need to be altered The default settings have been chosen because they provide the best operating conditions for your system AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setu PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Advanced chipset setup for configuring chipset features ESC Exit T Sel F2 F3 Color F10 Save amp Exit AMIBIOS SETUP ADVANCED CHIPSET SETUP C 2000 American Megatrends Inc All Rights Reserved Available Options Slow Refresh US 15us 14 318 2 Memory Hole at 15 16M Disabled PCLk2 3 RAS Precharge time 2 5T PCLK 2 4 RAS Active Time Insert wait Enabled PCLK 2 5 CAS Precharge Time Insert Wait Enabled PCLK 2 6 Memory Write Insert Wait Enabled PCLK 2 8 Memory Miss Read Insert Wait Enabled PCLK 2 10 SA Write cycle end Insert Wait Enabled PCLK 2 12 O Recovery Enabled O Recovery Period 10 75 us On Chip I O Revocery Disable ESC Exit j1 Sel 16Bit ISA Insert Wait Enabled PgUp PgDn Modify DE Controller Primary F2 F3 Color
38. n is set to Disabled AMIBIOS does not wait for you to press the lt F1 gt key after an error message The setting is Enabled or Disabled The default setting is Enabled Chapter 3 AMIBIOS Setup 33 34 ROM Location Setting C000 32K Shadow C800 32K Shadow D000 32K Shadow D800 32K Shadow These options control the location of the contents of the 16KB of ROM beginning at the specified memory location If no adapter ROM is using the named ROM area this area is made available to the local bus The settings are Setting Description The contents of C000h D800 are written to the same address in system memory RAM for faster execution Enabled If an adapter ROM will be using the named ROM area ROM area are written to the same address in system memory RAM for faster execution Also the contents of the RAM area can be read from and written to cache memory Disabled The video ROM is not copied to RAM The contents of the video ROM cannot be read from or written to cache memory PCM 3336 User Manual Advanced chipset setup Select the Advanced Chipset Setup from the AMIBIOS Setup main menu to enter the Chipset Setup The following configurations are based on the manufacturer s default settings This section allows you to configure the system based on the specific features of the installed chipset This chipset manages bus speeds and access to system memory resources such as DRAM and the external cache It a
39. nstallation 26 CHAPTER AMIBIOS Setup This chapter describes how to set the BIOS configuration data General information AMIBIOS Setup configures system information that is stored in CMOS RAM Starting AMIBIOS setup As POST executes the following appears Hit lt DEL gt if you want to run SETUP Press lt DEL gt to run AMIBIOS setup AMIBIOS main menu The AMIBIOS setup screen appears as follows AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 1999 American Megatrends Inc All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Standard CMOS setup for changing time date hard disk type etc ESC Exit JT Sel F2 F3 Color F10 Save 8 Exit 26 PCM 3336 User Manual Using a mouse with AMIBIOS setup AMIBIOS Setup can be accessed via keyboard mouse The mouse click functions are single click to change or select both global and current fields double click to perform an operation in the selected field Using the keyboard with AMIBIOS setup AMIBIOS Setup has a built in keyboard driver that uses simple keystroke combinations Keystroke Function gt lt 4
40. opy all the files that were just created in the temporary directory onto a formatted floppy diskette Step 2 Go to your 123 directory and start the installation program Type the following commands C lt ENTER gt INSTALL lt ENTER gt Step 3 The Lotus installation program will load and present the installation menu From this menu select Advanced Options From the Advanced Options menu select Add New Drivers To Library From the Add New Drivers Menu select Modify Current Driver Set From the Modify Driver Set Menu select Text Display From the Text Display menu select one of drivers Step 4 After the selection of the appropriate VGA display driver you will need to exit this menu and return to the Main Lotus Installation Menu Do this by selecting Return To Menu Step 5 At the Lotus Installation Menu select Save Changes 58 PCM 3336 User s Manual Step 6 At this point the Installation Menu will prompt you for the name of your new Lotus configuration file The Lotus system will prompt you with the default value 123 SET but you may want to use a filename that indicates the resolution of its driver For example if you installed the 132 column by 25 line driver you could name this driver 132X25 SET or if you installed the 80 by 50 driver you may want to call the file 80X50 SET Step 7 The installation of your Lotus 1 2 3 driver is now complete You will need to exit the Lotus installation program at this point At
41. ormance ESC Exit LT Sel F2 F3 Color F10 Save 8 Exit Chapter 3 AMIBIOS Setup 43 Auto configuration with optimal settings You can load the optimal default settings for the AMIBOIS setup options by selecting it from the main menu The optimal default settings are best case values that should optimize system perfor mance If CMOS RAM is corrupted the optimal settings are loaded automatically AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Supervisor Password Change Language Setting Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Load failsafe configuration settings ESC Exit LT Sel F2 F3 Color F10 Save 8 Exit 44 PCM 3336 User Manual Auto configuration with fail safe settings You can load the Fail Safe settings for the AMIBOIS setup options by selecting it from the main menu The Fail Safe settings provide the most stable settings though they may not provide optimal performance Use this option as a diagnostic aid if the system is behaving erratically AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Set Advanced CMOS Setup Advanced Chipset Setup PCI Plug and Play Setup
42. ost frequently asked questions you can easily find answers in your product documentation These answers are normally a lot more detailed than the ones we can give over the phone So please consult this manual first If you still cannot find the answer gather all the information or questions that apply to your problem and with the product close at hand call your dealer Our dealers are well trained and ready to give you the support you need to get the most from your AAEON products In fact most problems reported are minor and are able to be easily solved over the phone In addition free technical support is available from AAEON engineers every business day We are always ready to give advice on application requirements or specific information on the installa tion and operation of any of our products Product Warranty AAEON warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of shipment This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel autho rized by AAEON or which have been subject to misuse abuse accident or improper installation AAEON assumes no liability under the terms of this warranty as a consequence of such events Because of AAEON s high quality control standards and rigorous testing most of our customers never need to use our repair service If an AAEON
43. product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU type and speed AAEON products used other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return material authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of pur chase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Packing list Before you begin installing your card please make sure that the following materials have been shipped e 1 PCM 3336 CPU card Quick Installation Guide e Support CD contains the following
44. ry 640MB Time hh mm ss 12 19 46 Extd memory 3MB Floppy Drive A 1 44 MB 3 Floppy Drive B Not Installed LBA Bik PIO 32Bit Type Size Cyln Head WPcom Sec Mode Mode Mode Mode Pri Master AUTO Off Pri Slave AUTO Off Boot Sector Virus Protection Disabled Month Jan Dec Esc Exit T Sel Day 01 31 PgUp PgDn Modify Year 1901 2099 F2 F3 Color 28 PCM 3336 User Manual Date and Time Configuration Select the Date and Time icon in the Standard CMOS setup The current values for each category are displayed Enter new values through the keyboard or hit the or key to change values Floppy A Floppy B Select the appropriate specifications to configure the type of floppy drive that is attached to the system 360 KB 514 1 2 MB 544 720 KB 3 and or 1 44 MB 342 The settings have not been pre installed Master Disk Slave Disk Select the appropriate values to configure the hard disk type you are using for the master and the slave Available types are 1 46 USER AUTO Not Installed and CDROM The settings have not been preinstalled Boot Sector Virus Protection Enabling this option allows the system to issue a warning when any program or virus issues a disk format command or attempts to write to the boot sector of the hard disk drive Further confirmation is required before accessing this particular section of the hard disk drive Chapter 3 AMIBIOS Setup 29 Advanced CMOS setup Select t
45. t to DOS Step 2 Start WordPerfect and press lt SHIFT gt lt F1 gt to enter the setup menu Select D for Display and G for Graphics Screen Type and then choose the desired Chips VGA resolution 62 PCM 3336 User s Manual Configuring WordPerfect 5 0 for 132 columns Follow these instructions to configure WordPerfect 5 0 for 132 column text mode Step 1 To use the SETCOL program to set 132 columns and 25 rows type the following command SETCOL 132 25 lt ENTER gt Step 2 Start WordPerfect The program will detect the number of rows and columns automatically If for some reason WordPer fect is unable to adapt to 132 columns by 25 rows start WordPer fect with the following command WP SS 25 132 lt ENTER gt Configuring WordPerfect 5 1for 132 columns Start WordPerfect and press lt SHIFT gt lt F1 gt to enter the setup menu Select D for Display and T for Text Screen Type and then select Chips 132 Column Text Chapter 4 SVGA Setup 63 64 PCM 3336 User s Manual APPENDIX Installing PC 104 Modules This appendix gives instructions for installing PC 104 modules Installing PC 104 modules The PCM 3336 s PC 104 connectors give you the flexibility to attach PC 104 expansion modules These modules perform the functions of traditional plug in expansion cards but save space and valuable slots Modules include PCM 3115B PCMCIA Module Two slot PCM 3610 Isolated RS 232 422 485 Module PCM 3
46. the main Lotus Installation Menu select Exit NOTE If your driver set is not 123 SET you have to type the filename of your driver set in the command line when you start Lotus 1 2 3 For example if you named your driver set 132X25 SET type the following to start Lotus 1 2 3 123 132X25 SET lt ENTER gt Chapter 4 SVGA Setup 59 VESA The Video Electronics Standards Association VESA has created a standard for a Super VGA BIOS Extension VBE This defines a standard software interface to allow application programs to set and control extended video modes such as 800x600 graphics on video adapters from different manufacturers The VESA driver adds this Super VGA BIOS Extension to the VGA BIOS Any application program which supports the VESA standard driver interface can be used with this driver This VESA driver conforms to the VESA Super VGA Standard VS891001 Driver installation Step 1 Place the display driver diskette into drive A Make A the default drive by typing A lt ENTER gt Run the SETUP program by typing SETUP lt ENTER gt Press any key to display a list of supported applications Use the arrow keys to select VESA Driver Version 1 2 and press lt ENTER gt Press the lt ENTER gt key to select All Resolutions and press lt END gt to begin the installa tion A default drive and directory path will be displayed Use the backspace key to erase this and type in a directory that is in the directory path such as C
47. tings are Chapter 3 AMIBIOS Setup 41 42 Setting Description Normal The normal parallel port mode is used This is the default setting EPP The parallel port can be used with devices that adhere to the Enhanced Parallel Port EPP specifi cation EPP uses the existing parallel port signals to provide asymmetric bidirectional data transfer driven by the host device ECP The parallel port can be used with devices that adhere to the Extended Capabilities Port ECP specification ECP uses the DMA protocol to achieve transfer rates of approximately 2 5 Mbs ECP provides symmetric bidirectional communica tions PCM 3336 User Manual Change supervisor password 1 Select this option from the main menu 2 Enter the Password and Press lt Enter gt 3 Retype the Password and Press lt Enter gt If you forget the password please contact your distributor for another password which you can use to enter the AMIBIOS setup and change your own password AMIBIOS HIFLEX SETUP UTILITY VERSION 1 23 C 2000 American Megatrends Inc All Rights Reserved Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup Peripheral Setup Auto Detect Hard Disks Change User Password Change Language Setting Auto Configuration with Optimal Settings Auto Configuration with Fail Safe Settings Save Settings and Exit Exit Without Saving Load configuration settings giving highest perf
48. tion At this point the setup program locates the directory where Windows is installed For proper operation the drivers must be installed in the Windows subdirec tory Press lt ENTER gt to complete the installation Once com pleted the Display Driver Control Panel appears on the screen This Control Panel allows you to select and load the installed drivers Another method of installing these drivers is through the File Manager Click on Drive A Then double click on WINSETUP EXE to begin installation Changing Display Drivers in Windows To change display drivers in Windows select the Windows Setup icon from the Main window You will be shown the current setup configuration Select Change System Settings from the Option menu Click on the arrow at the end of the Display line You will be shown a list of display drivers Click on the driver you want Then click on the OK button Follow the directions to complete the setup Changing Color Schemes After you change display drivers you may notice that the color scheme used by Windows looks strange This is because different drivers have different default colors To change the color scheme select the Control Panel from the Main window Select the Color icon You will be shown the current color scheme Choose a new color scheme and click the OK button Chapter 4 SVGA Setup 53 DOS Setup Step 1 Install Windows as you normally would for a VGA display Run Windows to make sure that it
49. ules 67 LCD Display BIOS Configuration 70 Configuring various LCD display 71 CHAPTER General Information This chapter provides background information for the PCM 3336 Sections include e Card specifications e Board layout Introduction The PCM 3336 comes equipped with an embedded microcontroller ALI M6117C which is Intel 3865X 40 compatible In addition it comes with two serial ports RS 232 one bi directional printer port supporting SPP ECP and EPP modes an IDE HDD interface and a floppy disk controller With its industrial grade reliability the PCM 3336 can operate continuously at temperatures up to 140 F 60 C The PCM 3336 is specially designed as a compact all in one CPU card which incorporates a PC 104 connector into its design making non passive backplane SBC applications possible The numerous features provide an ideal price performance solution for high end commercial and industrial applications where stability and reliability are essential The PCM 3336 features an SVGA interface which supports CRT and Flat Panel TFT STN Mono and EL displays with 1 MB onboard display memory Features Onboard ALi M6117C Intel 386SX 40 compatible CPU e Onboard 4 Mbytes Fast Page DRAM e C amp T 65545 LCD controller with 1 MB display memory 2 PCM 3336 User s Manual Specifications General Fun

PCM-3336 - Elhvb.com

Contents

Download Pdf Manuals

Related Search

Related Contents