Instruction Manual - Maxi-Cosi
Contents
1. Base cien Front of vehicle Adjustable Headrest 5 position Air Protect Technology N d We M gt f Adjuster Latch y Tether Stra AN Anchor Fitting Buckle C Forward Facing Splitter Plate CFA Belt Path Rearward Facing Stabilising Arm Belt Path Fig 2 Fig 3 ANCHORAGE FITTING INSTALLATION Read and follow all of the installation instructions for maximum protection If you have any questions regarding the installation or use of this restraint please con tact IGC Dorel or a child restraint fitting station authorised by the relevant State Government body or in New Zealand to consult the agent for the vehicle This restraint must be used with an adult lap or lap sash seat belt Do not modify or alter this restraint in any way Use only IGC Dorel recommended parts and accessories Protect all webbing from possible damage by sharp edges and corners Check your vehicle owner s handbook for the location of correct anchorage points and the possible need for spacers If a suitable anchorage point cannot be found contact a child restraint fitting station for recommendations about your vehicle Some vehicles may have anchor points which are recessed below the vehicle trim spacers are supplied to raise the anchor point if required Extension straps and extra fittings are available from various stores INSTALLING LOCKING CLIP OPTIONAL Using the seat belt locking clip2. forget to remove the instruction manual Machine wash in cold water delicate cycle Tumble dry 10 15 minutes on low heat Do not dry clean All other surfaces should be cleaned with a mild soap and water Never clean with bleach or spirit type cleaners Do not use the restraint without the cover Check the webbing for fraying REMOVE TRIM FOR CLEANING Hemove Harness Straps From Splitter Plate Fully loosen harness straps From the back of the restraint remove both harness straps from splitter plate Remove Harness Straps Feed harness straps throught headrest To Remove trims Headrest Trim Move headrest to highest position Remove trim from 2 plastic hooks at back of headrest Pull the plastic harness guide with one hand while pulling off the headrest trim around it Repeat same process on the other side and remove trim Seat Trim Adjust backrest to lowest position Release the elastic straps on the back of the child restraint Pull pad off the top of child restraint and around headrest Replace trim by reverse order 19 CARE INSTRUCTIONS VERY IMPORTANT Only use this child restraint with the cover supplied or a manufacturer authorized replacement cover with identical shoulder height markers HOOD FITMENT If supplied Hood To fit the hood line up the press stud with the one in the trim press firmly Refer to Fig 40 Repeat on the next side Match up velcro on the back of the hoo
3. plug from the parcel shelf floor roof and install the attachment bolt as shown in Fig 7 Attachment Bolt Lock Washer CAUTION DO NOT OVER TIGHTEN Anchor Fitting THE ATTACHMENT BOLT FeA Spacers if required MAXIMUM TORQUE 2 e eie Tum 20 Nm Newton Metre AR LA Vehicle Metal Structure amp FRONT OF VEHICLE E e Front of vehicle i Fig 7 If the car is not fitted with a child restraint anchorage point For sedans only Drill a 9mm diameter hole in the parcel shelf on the centre line of the seating position as shown in Fig 8 Install the anchor bolt as shown in Fig 9 For vehicles other than sedans In Australia consult your nearest child restraint fitting station or traffic authority for vehicle inspection to find the best correct position for the placement of the anchorage point and for the correct attachment bolt length and use of spacers In New Zealand consult the agent for the vehicle WARNING CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND METAL OR TO WOOD OR SYNTHETIC STRUCTURES WHEN DRILLING THE 9MM HOLE DO NOT DRILL THROUGH FUEL LINES FUEL TANKS ELECTRICAL WIRING OR RADIO SPEAKERS WEBBING STRAPS MUST BE PROTECTED FROM SHARP CORNERS AND EDGES THE ANCHOR FITTING MUST BE USED ONLY AS DIRECTED ABOVE IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT TN B Attachment Bolt Anchor Fitting Spacers ep if required 3 ies c Vehicle Trim Vehicle Centre line of
4. to convert a lap sash belt to a lap only belt NOTE Locking clip can be fitted on either side depending on the vehicle seatbelt and child restraint configuration 1 Using a locking clip Fig A to convert a lap sash belt to a lap only belt 2 Hold the lap and sash straps Fig B together Thread webbing still pinched into the locking clip one side at a time Fig C amp D 3 Repeat step 2 for the other slot in the locking cip Fig E amp F Feed the straps through the locking clip to remove any slack 5 If the locking clip is on correctly it will hold the lap belt securely if the lap belt slips repeat the previous steps 6 Locking clips are available from most speciality outlets or from IGC Dorel Customer Service 1300 809 526 Fig 4 JI 9 IMPORTANT Child restraints must be used correctly to provide proper protection for your child The new type of clip anchorage system on child restraints must be used in the correct way Be especially careful to use the clip in the following way RIGHT Make sure there is no slack in the top strap and the attachment clip is upright in the anchorage fitting WRONG The clip must not lie flat on the anchorage fitting ANCHORAGES IN VERTICAL PANEL AT REAR OF VEHICLE If the car is fitted with a child restraint anchorage point Locate the anchorage point behind the rear seating position consult the car owner s handbook for the location of the anchorage point Remove the thread
5. Dorel or agent or a child restraint fitting station authorised by the relevant transport authority or in New Zealand to consult the agent for the vehicle No child restraint can guarantee absolute protection from a crash However proper use of this restraint may reduce the risk of injury or death To be used only in a rearward facing position for an infant until their shoulders reach the lower shoulder height marker approximately 12 months of age Then to be used in forwardfacing position until their shoulders reach the upper shoulder height marker approximately 4 years of age Continue to use this child restraint until the child reaches this limit Do not use forward facing until child s shoulders are above the lower shoulder height marker Infants are at risk of serious injury if they face forward too early Children are at risk of serious injury if they move to booster seats too early Children that have outgrown this restraint are safest in a booster seat until their shoulders reach the upper shoulder height marker of the booster seat TO BE USED WITH ALAP SASH LAP ONLY SEAT BELT IN THE FRONT BACK OF MOST CARS WITH FORWARD FACING SEATS CHECK THAT THIS CHILD RESTRAINT WILL FIT IN YOUR CAR NOTE CHECK THE MEASUREMENTS BETWEEN THE SEAT BACK OF THE REAR SEAT AND ALL FRONT SEATS IN THE VEHICLE IN WHICH THE CHILD RESTRAINT IS INTENDED TO BE USED TO ENSURE THAT THE SPACE IS SUFFICIENT THIS RESTRAINT MUST BE ATTACHED TO A CHILD RES
6. IG DOREL Pty Ltd Instruction Manual CONVERTIBLE CAR SEAT CCA 2010 FORWARD FACING 12 months to approximately 4 years of age Illustrations are representative only Design and style may vary IMPORTANT KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT Before You Start Thank you for purchasing this child seat This product is suitable for toddlers and older children We welcome you as a valued customer and trust that your child will enjoy many years of comfort and safety No child restraint can guarantee absolute protection from a crash However proper use of this restraint may reduce the risk of injury or death CONTENTS Page2 3 Page 4 Page 5 7 Warnings Parts List Anchorage Fitting Installation Locking Clip Page 8 Page 9 Page 11 Page 10 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Preparing Infant Seat To Fit Your Child Base Adjustment Correct Rearward Facing Vehicle Position Adjusting Tether Strap Shoulder Marker Height Rearward Facing Rear Facing Installation Correct Forward Facing Vehicle Position Shoulder Marker Height Forward Facing Forward Facing Installation The next seat for your child Cleaning Instructions For Buckle Care Instructions Hood Fitment Read and follow all of the installation instructions for maximum protection If you have any questions regarding the installation or use of this restraint please contact IGC
7. TRAINT ANCHORAGE POINT IN THE CAR REFER TO CAR OWNER S HANDBOOK FOR LOCATION OF ANCHORAGE POINTS REFER TO A CHILD RESTRAINT FITTING STATION IF NO ANCHORAGE POINTS ARE IN THE MOTOR CAR THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE ANCHORAGE STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK E G HATCHBACK OR WAGON NOTE An extension strap may be needed to fit this child restraint into the vehicle Extension straps 300mm ref no 921 and 600mm ref no 922 and an anchor bolt kit ref no 525 are available from various stores 2 deo aes To ensure that your child gets all the protection designed into this restraint you MUST read and Use the restraint exactly as shown in the instructions Fit the restraint firmly to the car seat Fit the harness firmly to the child A loose restraint or harness is dangerous Do not alter or modify this restraint DO NOT USE A REAR FACING CHILD RESTRAINT WHERE AN AIRBAG IS FITTED IN FRONT OF THE SEATING POSITION DO NOT USE THIS SAFETY SEAT WITHOUT ITS COVER Supervision of children is needed because they may be able to undo buckles Failure to follow these instructions may result in your child striking the vehicle s interior during a sudden stop or crash To ensure baby s back is evenly supported do not put more than one nappy on the baby and make sure the nappy is not thickly folded at the back Repairs must only be done by the manufacturer or agent Destroy the restraint i
8. ar seat is equipped with a buckle designed to give your child maximum protection during proper use When working properly your buckle should always fasten with an audible click If sticky liquids such as baby food fruit juice etc get into the buckle it may become sluggish and you will not hear a click The buckle should be cleaned by following the steps below into slot Fig 36 1 Fold seat cover and foam back from buckle using a flat edged screwdriver gently lift one end of rod out releasing crotch buckle repeat for other side 2 As illustrated in Fig 34 place the buckle unit under running water 40 degrees celcius Let the water flow through the mouth of the buckle for one minute 3 Simultaneously latch and unlatch the tongues into the buckle several times until a strong audible click is heard Refer to Fig 35 4 If you still cannot hear a strong audible click after latching the buckle several times repeat steps 2 and 3 5 DO NOT oil any part of the buckle 6 Allow buckle to dry 7 Refit crotch buckle ensuring RED button is facing out 8 Thread the webbings as shown with arrows in Fig 36 9 Put the 2 metal rods back into the webbing loops and push into the slots 10 Pull the buckle to make sure that it is fitted properly 11 If the buckle does not return to original working order contact IGC Dorel Customer Service on 1300 809 526 18 CARE INSTRUCTIONS Seat trim may be removed for cleaning Don t
9. d with velcro on seat trim press the 2 pieces of velcro together firmly Refer to Fig 41 BACK VIEW Fig 40 Fig 41 20 NOTE 21 NOTE 22 IES DOREL Pty Ltd GUARANTEE IGC Dorel Pty Ltd warrants your new product to be free from defects in materials and workmanship for 6 years on the seat amp 2 years on the trim from the date of purchase provided that the product is used in accordance with accompanying recommendations or instructions where provided The benefit of this warranty is in addition to your rights under the Australian Consumer Law and to other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates IGC Dorel Pty Ltd will provide you with your choice of a refund repair or exchange where possible for this product if it becomes defective within the warranty period IGC Dorel Pty Ltd will bear the reasonable expense of claiming the warranty This warranty will no longer apply where the defect is a result of alteration accident misuse abuse or neglect Please retain your receipt as proof of purchase and contact our Customer Service Centre on Ph 1300 809 526 or alternatively via our website at www igcdorel com au for any difficulties with your product Warranty claims and claims for expense incurred in returning this product can be addressed to our Customer Service Centre at 655 685 Somerville Road West Sunshine VIC 3020 Hours 8 30 am
10. f it has been in a severe crash even if no damage is visible Do not allow the restraint to come into contact with polishes oils bleach and other chemicals Clean with mild soap and water Do not allow sharp or heavy objects to be loose in the vehicle Anything loose can be deadly in a crash Premature infants may have difficulty breathing when in a sitting position Consult your doctor before using this or any restraint with a premature infant Child restraints and their components can become very hot in sunlight Always check the restraint for heat before putting a child in the seat Make certain children are shaded from direct sunlight while in a well ventilated vehicle Do not allow a child to have anything like a bottle lollipop or ice cream on a stick A bump or swerve could cause these objects to injure your child Straps may be damaged by unsecured cargo in a collision Secure or remove hazardous cargo before using this strap Hatch back or wagon Do not use the child restraint where this strap may fall into a split in the seat back Always attach hook and remove slack DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR Please contact IGC Dorel Customer Service with any questions or concerns PARTS LIST MA Hood Attachment if supplied Tether Strap Insert Belt Mates Stabilising Arm if supplied Design and style may vary Instruction Manual Adjuster Belt Anchorage bag Base adjuster 3 position Recline Arm
11. he lower shoulder height marker Infants are at risk of serious injury if they face forward too early NOTE If the baby s neck muscles are unable to support their head then the child should remain rear facing NOTE Turn the seat to forward facing when the child s shoulders reach the lower height marker 12 REARWARD FACING INSTALLATION Set base in position 3 High Swing stabilising arm into position Fig 23 Place restraint facing rearwards on back seat of vehicle in line with an anchorage strap anchorage point Thread the vehicle seat belt through the BLUE belt path at the front of the restraint and fasten buckle 5 Press the child restraint into the vehicle seat and remove belt slack Attach the anchorage strap to the anchorage point Adjust until all the slack is removed Ensure Base of seat is not lifted Fig 24 PRESS HERE REARWARD FACING BELT PATH REARWARD FACING BELT PATH 13 CORRECT FORWARD FACING VEHICLE POSITION INCORRECT USE SHOULDER MARKER HEIGHT FORWARD FACING Strap can slot above Ad X FORWARD FACING 6 months to 4years Child Shoulders gt are nearest to the child s shoulders but not Strap cannot more than 25 mm below the child s shoulders be more than 25mm below SHOULDERS MUST BE BELOW THIS LINE UPPER label Cc us Front of vehicle SHOULDER MARKER To be used in forward facing position until their shoulders reach the uppe
12. r shoulder height marker approximately 4 years of age Continue to use this child restraint until the child reaches this limit Do not use forward facing until child s shoulders are above the lower shoulder height marker Infants are at risk of serious injury if they face forward too early Children are at risk of serious injury if they move to booster seats too early Children that have outgrown this restraint are safest in a booster seat until their shoulders reach the upper shoulder height marker of the booster seat NOTE The child should not sit forward facing until the baby s neck muscles are able to support their head CHECK POSITIONING OF STRAPS AND ADJUST HEADREST PRIOR TO INSTALLATION 15 FORWARD FACING INSTALLATION TODDLER 12MONTHS TO 4YEARS OLD PUSH base adjuster in red under front seat and rock seat to adjust the base 3 positions FORWARD FACING Red base adjuster BELT PATH under front of seat 1 Adjust the child restraint to the forward facing position Fold the Stabilizer Arm if the restraint has been used for rear facing 2 Adjust the base to suit your child as fitment in some vehicles can be impacted due to the location of anchorage points or the shape of rear seats 3 positions base adjustment 3 Adjust the shoulder straps and headrest to fit your child Refer to page 8 4 Place restraint facing forwards on back seat of vehicle inline with an anchorage strap anchorage point 5 Th
13. read the vehicle seat belt through the YELLOW belt path 6 Press the child restraint into the vehicle seat and remove slack 7 Attach the anchorage strap to the anchorage point Adjust until all the slack is removed Refer to page 10 NOTE If the car seatbelt is not long enough to secure the child restraint DO NOT USE SEAT BELT EXTENDERS c NOTE Infant Insert where supplied shall not be used in forward facing position Only used in seat on bottom two slots when rear facing Infant Insert 16 THE NEXT SEAT FOR YOUR CHILD SHOULDERS MUST BE BELOW THIS LINE UPPER label Docs Front of vehicle gt SHOULDER MARKER To be used only in a rearward facing position until the infant s shoulders reach the lower shoulder height marker approximately 12 months of age Then to be used in forward facing position until the shoulders reach the upper shoulder height marker approximately 4 years of age THE NEXT SEAT Booster seat Children that have outgrown this restraint are safest in a booster seat until their shoulders reach the upper shoulder height marker of the booster seat NOTE This illustration is representative only Design and style may vary Fig 33 17 CLEANING INSTRUCTIONS FOR BUCKLE Follow the manufacturer s instructions at all times Before removal ensure you have carefully noted the way which the various parts are attached to the seat so as to facilitate reassembly Your child c
14. seat to adjust the base 3 positions Red base adjuster under front of seat ADJUSTING TETHER STRAP PULL TO LOOSEN M NC SN SA AU Y M TO ADJUST TETHER STRAP BUTTON To loosen Press on the adjuster button with thumb and pull strap back through to loosen anchorage strap using strap which is attached to the seat FIG A To Tighten Adjust anchorage strap and remove slack Pull loose end of strap to tighten FIG B Ec s Front of vehicle FORWARD FACING REARWARD FACING Fig 16 Fig 17 10 CORRECT REARWARD FACING VEHICLE POSITION CORRECT USE CORRECT USE 640mm Fig 20 ANGLE CONFIGURATION FOR SEAT Position seat ensuring that the angle is no greater than 40 from horizontal plane Angular adjustment is achieved by adjusting the base See page 9 for base adjustment 11 SHOULDER MARKER HEIGHT REARWARD FACING REARWARD FACING Newborn to 12 months The shoulder straps must be in the slots which are nearest to the child s shoulders but not lower than the child s shoulders Shoulder strap MUST BE REAR FACING WHEN SHOULDERS BELOW THIS LINE Lower label 1 CALLS Front of vehicle SHOULDER MARKER To be used only in a rearward facing position for an infant until their shoulders reach the lower shoulder height marker approximately 12 months of age Fig 22 Do not use forward facing until child s shoulders are above t
15. seating position Reinforcing Metal Structure Washer Lock Washer FRONT OF VEHICLE PP Securing Nut lt FRONT OF VEHICLE Fig 9 PREPARING INFANT SEAT TO FIT YOUR CHILD You MUST make these adjustments with your child before you install the child restraint in the vehicle Please adjust harness according to the infants shoulder height prior to installation CONFIGURING THE HARNESS BELT FOR SHOULDER HEIGHT Lift the harness release lever at the front of seat e O Pull one side of the shoulder strap to loosen amp Press red button to release buckle assembly for ease of child fitment Pull harness straps over sides of infant seat Place child in seat ADJUST HEADREST HEIGHT Rotate harness height adjustment levers inward Move headrest to the proper height and lock into place Q Fasten buckle assembly See Page 9 Pull the adjuster belt at the front of the seat until the harness belt lies firmly against the child Failure to fasten and tighten the harness system correctly can result in serious injury or death PREPARING INFANT SEAT TO FIT YOUR CHILD TO FASTEN BUCKLE ASSEMBLY Step 1 Insert one buckle tongue as shown above Step 2 Insert the second buckle tongue as illustrated above Listen for a CLICK Step 3 Remember to always pull up on the harness straps to make sure buckle is locked tightly BASE ADJUSTMENT PUSH base adjuster in red under front seat and rock
16. to 4 30 pm Monday to Friday For New Zealand please contact Customer Service Centre 14 Sir William Avenue East Tamaki Auckland 2013 Auckland 09 274 1040 NZ wide 0800 628 000 Toll Free Hours 8 00 am 4 00 pm Monday to Friday Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure IMPORTANT KEEP THIS INSTRUCTION MANUAL IN THE POCKET PROVIDED AT THE REAR OF THE SEAT Ref 012162 Australian 02 42 Standard ASINZS 1754 Lic 1491 SAI Global dad i v O tae o v Q En Q U
Download Pdf Manuals
Related Search