Zycoo U50 Quick Install Guide
Contents
1. IP address is usually in the 192 168 1 X range Step2 Start a web browser To use the user interface you needa PC with Internet Explorer version 7 0 or higher Firefox Chrome Step 3 Enter the default address http 192 168 1 100 9999 of the CooVox device into the URL address box Step4 Enter the default username admin and password admin Then click Login to enter the Web based user interface ZX ip pone system Username password M En el English a Default URL address http 192 168 1 100 9999 Default Username admin Default Password admin J 08 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 3 2 Network Configuration Step1 Goto Network Settings Network Network Home Operator Pv4 Settings IPv6 Settings VLAN Settings Basic Inbound Control Ethernet Port Setup Advanced IP Assign Static V Hostname CooVox U50 Network IP Address 192 168 1 100 Static Routing Subnet Mask 255 255 255 0 __ Gateway 192 168 1 1 Dana Primary DNS 8 8 8 8 ERASE Alternate DNS DHCP Server DDNS Settings Virtual Interface SNMPv2 Settings IP AddressV1 Subnet MaskV1 Troubleshooting IP AddressV2 Subnet Maskv2 Security Save Cancel Report System Step 2 Configure the network information There are three types of network connection They are Static DHCP PPPoE Point to Point Protocol over Ether2. only the power adapter provided with IP PBX m Make sure that the supply voltage matches the specifications indicated on the rear panel of IP PBX To avoid the electric accident do not open or remove the cover of IP PBX when it is working as well as off the power m Before cleaning the device cut off the power supply Do not clean it by the waterish cloth and never use any other liquid cleaning method Site Requirements To ensure normal operation and long service life of the device please install it in an environment that meets the requirements described in the following subsection Please keep a proper temperature and humidity in the equipment room Too high low humidity may lead to bad insulation electricity leakage mechanical property changes and corrosions Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device For normal temperature and humidity of the device please check the following table 03 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 Environment Temperature Humidity Operating 0 c 40 C 10 90 RH Non condensing Storage 40 C 70 C 5 90 RH Non condensing Clearness The dust accumulated on IP PBX can be absorbed by static electricity and result in poor contact of metal contact points Some measures have been taken for the device to prevent static electricity but too strong
3. Za Ge We Focus We Deliver IP PHONE SYSTEM CooVox Series USO For Small and Medium Business Quick Installation Guide co uk sales voipon co uk Table of Contents 1 Package Contents Sehat balai 02 2 Hardware Installation aaa 02 2 1 Safety Precautjons 2 cs Pa ee As 03 29 Productimstallation 62 62 een BE Sa 05 2 3 Physical Connection one 06 IA Led Definition see a E ee es 07 3 Basic System Configuration en 08 31 Webilosih ee na 08 3 2 Network Configuration esensi 09 3 3 Choose the Module soon anna 10 JA Reset to factory A SR See A aa 11 4 Further Configuration si sbagai nek tte ban badaaklamag 12 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 1 Package Contents Thank you for purchasing ZYCOO IP phone system These are the items Included with your IP phone system purchase id Power Adaptor QuickInstallation Antenna only for Guide GSM Module Two mounting brackets Warranty Card and fittings 2 Hardware Installation The followings are the instructions for setting up ZYCOO CooVox U50 IP PBX Please refer to the illustration and follow the simple steps below to quickly install your IP phone 02 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 2 1 Safety Precautions Notes To avoid any device damage and bodily injury caused by improper use please observe the following rules E Keep the power off during the installation m Use
4. dule slot through the guide rail 5 Tighten the locking screws on the both ends of the module 05 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 Caution Do not touch any device on the module just to prevent the module from being damaged by static electricity This operation must be done with power cut off The module does not support hot plugging Desktop Installation Please place the IP PBX on a steady platform Caution Please set 5 10cm gaps around the device for air circulation mPlease avoid any heavy thing placed on the device Rack Installation Optional CooVox U50 is not a standard 19 inch rack mountable device but we can provide the mounting brackets to help you install the device to the rack if necessary 2 3 Physical Connection CooVox U50 Analog Phone Router 06 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 2 4 LED Definitions Indication Function Status Explaination On PWR Power Status Off Blink SYS System Status Off Blink ETH Data Status Off USB Data Stat On ata Status Of FXS FXO GSM 1 4 SLOT1 SLOT1 Status E1 T1 BRI FXS 1 4 SLOT2 SLOT2 Status EXO GSM 07 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 3 Basic System Configuration 3 1 Web Login Step 1 Connect a computer and the CooVox device in the same network
5. f 192 168 1 x Press the Reset button and all the system data will be reset to default so if possible back up the configuration file before reset 11 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 4 Further Configuration Thank you for the purchase of ZYCOO products The above steps introduce simple configuration for CooVox U50 For further configuration please refer to the user manual If you have other questions please contact the local dealer or distributor from which you purchased this product You can also browse our online FAQ resource at the ZYCOO Web site first to check if it could solve your issue If you need more support please contact ZYCOO support team ZYCOO online FAQ Http www zycoo com support Support team mail address support zycoo com Copyright Zycoo Co Ltd 2013 11 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 Za de We Focus We Deliver co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1
6. net You can find detailed settings in the user manual WAN Port Setup IP Assign ei DHCP Hostname pppoe IP Address 192 168 1 100 Subnet Mask 255 255 255 0 Gateway 192 168 1 1 Primary DNS 8 8 8 8 Alternate DNS 1 c0 uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 3 3 Choose the Module Go to System gt Module Settings When using the module except FXO FXS GSM you need to set the module parameters with the below page SLOT1 Module Type FXS FXO GSM V Save Cancel Module Type Select the module type of the device slot FXS FXO GSM module Default type You don t need set anything for these modules a 1 T1 module SLOT 1 Module Type E1 T1 E1 T1 Settings Mode ELM Signalling CPE vV Framing CCS v Coding HDB3 V CRC4 v Save Cancel 10 1 co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 m ISDN BRI module SLOT 1 Module Type ISDN BRI 4 BRI Settings Type of Port 1 TE V Type of Port 2 TE V Type of Port 3 TE vi Type of Port 4 TEEN Save Cancel 3 4 Resetto factory To reset the IP address to the default IP Address 192 168 1 100 ETH or reset the login password to default value press the hardware reset button at the front panel more than 5 seconds After the device is rebooted you can login the management WEB interface within the same subnet o
7. static electricity can cause deadly damage to the electronic elements on the internal circuit board To avoid the effect of static electricity on the operation of IP PBX please attach much importance to the following items Dust the device regularly and keep the indoor air clean Keep the device well grounded and ensure static electricity has been transferred Electromagnetic Interference Se O 04 1 co uk sales voipon co uk Tel 44 0 1245 808195 Fax 44 0 1 Electronic elements including capacitance and inductance on the device can be affected by external interferences such as conducted emission by capacitance coupling inductance coupling and impedance coupling To decrease the interferences please make sure to take the following measures Use the power supply that can effectively filter interference from the power grid Keep the devices far from high frequency strong current devices such as radio transmitting station Use electromagnetic shielding when necessary 2 2 Product Installation Module Installation This IP PBX can support installing two extension modules at the same time Optional modules are as follows 4FXS Module 2FXOS Module 4FXO Module 2GSM Module m1E1 T1 Module 1 Check if the module is clean and intact 2 Please ensure power of IP PBX is cut off 3 Please ensure the direction of the module is correct ZYCOO logo side up 4 Push the module into the mo
Download Pdf Manuals
Related Search