"user manual"
Contents
1. 2 Memory function Press COLOR again on Orbit TP the changes will be saved and replaced the prime colors D Note SPEED mode is not functional under RGB mode WHITE 1 Fora quick change of the intensity it be adjusted by gliding the slider on Orbit 2 Memory function Press COLOR again on Orbit TP the changes will be saved and replaced the prime color D Note WHITE only can be applied in CHO4 mode T 021 can not operate this function FADING C Before operate this FADING mode please check every lighting fixtures has set the DMX address correctly 000 o Under the power off circumstances Press RGB and BRIGHTNESS on the device panel at same time and select the numbers of lights by gliding the slider After finished setting press the circle with ON OFF letter to start operating o For DMX address setting please refer user manual of dipswitch page of Orbit lighting include with package o The maximum channel number can set up are 60 groups 1 DMX channel needed for single color led fixture 3 DMX channel needed for tri color led lighting fixture 4 DMX channels needed for four color led lighting fixtures DMX setting example www colorbeam com OPERATION Example 1 a Condition Total 30 units with RGBW 4 color led install in2. resetting is success D Note T 021 can not operate the reset function 2 Original setting MODE 4CH COLOR C01 FADING F01 RGB 000 WHITE 000 BRIGHTNESS 255 LGHTS 12 nos C1 Red C2 Green HH www colorbeam com OPERATION 4 COLOR CHANNEL MODE Fixed Color Effects E 1 There are 11 built in fixed colors The fixed colors be selected by gliding the slider on Orbit TP 2 Adjust the hue spectrum value of fixed colors by touching the slider on Orbit TP and pressing COLOR again to create custom colors When see the display is blinking one time means the custom color is saved 3 Operation Example Condition Adjust C01 to orange color under fixed COLOR mode Touch the bottom RGB and select C01 using slider to select the number 30 o Touch the bottom WHITE to mix the color using slider to select the number 70 Touch the bottom BRIGHTNESS to adjust the brightness to get your favorite light orange color When finish the above steps touch bottom COLOR again to save the new color D Note COLOR mode is not functional under fixed COLOR mode RGB 1 Fora quick change of the color illumination in fixed COLOR mode the colors can a be adjusted touching the slider on Orbit TP Orr Red Orange Yellow Green Blue Indigo Purple White
3. COLORBEAM User Guide 0104 Q 7 4 o RGB 2 oi y coL ORBEA 7 ORBIT TP Easy Touch Panel amp T1021 Remote Control System B 6 C Yani Come SEs Version 1 0 December 2012 CONTENIS 1 2 3 4 5 6 7 8 ITEMS INCLUDED BEFORE UNPACKING FUNCTION SCHEMA amp INSTALLATION WIRING WARNING on mena ena OPERATION oreren mure A qx ORDER INFORMATION c HH www colorbeam com ITEMS INCLUDED Please make sure the below items were inlcuded when unpacking If there is anything missing please call your local dealer immidently 8 COLORBEAM 7 J O R B IT T P Remote Controllor Wall Fixed Plate 1pcs www colorbeam com INTRODUCTION COLORBEAM design simple operation control system ORBIT TP and T021 remote control for ORBIT series lights built in program with 3 channel modes 1 color channel mode 3 color channel mode 4 color channel mode which is suitable with any led lighting fixture in the market The Orbit TP with 11 built in fixed color can be memories easily with adjustable the brightness and color 7 built fading mode can adjust the speed by user s pref
4. 5 groups needed every 6 units in same address total needed 5 DMX address number b DMX address setting Group 1 the first 6 units DMX address setting 1 Group 2 the second 6 units DMX address setting 5 Group 3 the third 6 units DMX address setting 9 Group 4 the fourth 6 DMX address setting 13 Group 5 the fifth 6 units DMX address setting 17 For DMX address setting please refer user manual of dipswitch page of Orbit lighting include with package c CH setting must be 5 for each group under this condition Example 2 a Condition Total 4 units with tri color led every unit need one address total need 4 DMX address number b Group 1 the first unit DMX address setting 1 Group 2 the second unit DMX address setting 4 Group 3 the third unit DMX address setting 7 Group 4 the fourth unit DMX address setting 10 For DMX address setting please refer user manual of dipswitch page of Orbit lighting include with package c CH setting must be 4 for each group under this condition 1 There are 7 preset fading effects G F01 Color fade All the fixtures run the fixed colors in order simultaneously 5 F02 Cross fade All the fixtures will be separated into two groups which based on p odd and even numbers Each group will run a smooth transition from one c solid color to another sequentially F03 Color Cavort An animated color effect will chase in order from the
5. for the desired color 666 2 For a quick change of the speed in FADING mode the colors can be adjusted by gliding the slider on Orbit TP BRIGHTNESS 1 For a quick change of the brightness in COLOR and FADING mode the colors can be adjusted by touching slider on Orbit TP D NOTE In FADING mode the lowest brightness value can only be adjust to the 100 3E COLORBEAM 3 COLOR CHANNEL MODE C 1 In3 color channel mode only WHITE can t be display The other functions are the 6 same as 4 Color channel Mode 008 1 COLOR CHANNEL MODE 1 In 1 color channel mode only the slider can adjust BRIGHTNESS will be amp amp shown when press other button Press the button to turn on off the device 1 Press to see the present channel mode 2 To adjust the channel mode press and hold the buttom still for seconds until the display flickering then select the channel mode After finished setting press 1 tooperating the device Press and 79 toselect the fading mode Press and 79 toselectthe fixed color Press and to adjust the fading speed Press toadjustthe brightness When the device is power off press or buttom to change th
6. e numbers of the light address group Press after finished setting COLORBEAM T021 ORDER INFORMATION FORM CONTROLLER ITEM a SPEC PART NUMBER ORBIT TP __ GOBCO 111 ORBIT TO21 S 7 7 B030210001 ACCESSORY ITEM SPEC PART NUMBER 4 PIN CABLE for ORBIT Series 1M D03 994001 002 www colorbeam com COLORBEAM CO LTD 314 3F No 87 Minguang E Rd Taoyuan City Taiwan 33052 TEL 886 3335 7716 FAX 886 3 331 3386 E MAIL sales colorbeam com W www colorbeam com
7. e unit ON OFF 9 Wo The display will fade out when turning off the device When the device is turned on will be displayed and it will start the last used mode amp 2 Memory function Memory function The controller will automatically memories the last setting when turn off the unit and will continue to perform when turn on the unit again CHANNEL MODE SETTINGS 4 1 Orbit TP is suitable for single color 1CH tri color RGB 3CH four color RGBW ACH fixtures Please kindly note that the channels need to be set accurately before operations ep 2 Setting Press RGB and WHITE on the device panel together and select the channels by slider while the device is turned off The display will show 3 after finished the setting After finished the setting touch the button ON OFF to start operating the device Channel Mode First Light 1 Color CH Mode 1CH W 3 Color CH Mode 1CH R 2CH G 3CH B 4 Color CH Mode 1CH W 2CH R 3CH G 4CH B RESET 1 This function is for user to reset to original setting from factory Make sure the panel device is in OFF condition and the display shown 3 Touch and hold the BRIGHTNESS and SPEED together until 5 vanish and A the display show C014 When see the display show C014 means the
8. erences Features 1 Easy wiring 2 Easy operation by touch panel IR remote control 4 Friendly Interface 5 3 Channel modes 6 11 fixed color mode 7 fading mode 8 RGB and WHITE adjusting 9 BRIGHTNESS and SPEED adjusting 10 Memory Capability H www colorbeam com SPECIFICATION Electrical Power Voltage 24 VDC ORBIT TP Power Requirement Lithium Battery model no CR2025 T021 Communication USITT DMX512 A address setting Function Power on off Channel mode single color 3colors 4colors 11 pre set static colors 7 pre set fading mode RGB White adjustment individual opeed adjustment Brightness adjustment otorage function Housing Dimension mm ORBIT TP L90 x W90 x H21 5 T021 L82 89 x W30 89 x H9 4 Weight ORBIT TP 138 5 g T021 16 5 Color White Listing Certifications CE RoHS WEEE DIMENSIONS 30 89mmM_ 21 5mm 90mm OO OO O O 82 89mm QOO QOO QF TO21 ORBIT TP www colorbeam com FUNCTION SCHEMA INSTALLATION FUNCTION SCHEMA On Off Channel Mode Key Terminal Block of Wiring Lights Adjustment Key Seven Segment Displays Touch Panel Wiring Information D Symbol Cable Color Description DH White DMX D o Green DMX 0 0 Sl Touch Slide GND Black GROUND Red DC24V INSTALLATION Please unplug from the mains before installation 1 Pass the wires
9. first fixture to the last one F04 Color Sweep A smooth color transition will spread from the first fixture to the last one F05 Rainbow Cavort A sequence of rainbow colors will chase from the first fixture to the last one in one direction F06 Rainbow Sweep Asequence of rainbow colors moving in one direction gradually F07 Color fade All the fixtures run the fixed color C1 and C2 in order simultaneously example 1 2 1 2 1 C2 2 The FADING effects can be selected by gliding the slider on Orbit TP 3 Memory function In fading mode the changes are saved automatically each time when enter a new value 4 Operation Example Condition Under the FADING mode adjust BRIGHTNESS and SPEED of F01 To adjust the brightness of F01 touch BRIGHTNESS bottom first and slide the slider to get favorite brightness O To adjust the speed of F01 touch the SPEED bottom first and slide the slider to get the favorite speed o The adjustment of BRIGHTNESS and SPEED will save automatically Please do not touch FADING bottom again D NOTE RGB and White mode cannot be used in FADING mode the display will shown 3 only the BRIGHTNESS and SPEED can be adjusted e NOTE In FADING mode the lowest brightness value can only be adjust to the 100 H www colorbeam com OPERATION amp ORDER INFORMATION SPEED 6 1 In FADING mode it can adjust from value 1 10
10. s with local electrical codes Do not expose the device to heat source corrosive flammable or explosive area Do not block any of ventilation openings Do not open the device and try to repair the device personally m CAUTION 2 Operation Determinations N For non Colorbeam fixtures refer to the The device must only be used indoor wiring diagram for installation If the device has been exposed to drastic temperature fluctuation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Only operate the device after having checked the housing which is firmly closed and all screws are tightly fastened Do not shake the device Avoid brute force when installing or operating the device Operate the device only after having familiarized with its functions Do not permit operation by persons who are not qualified for operating the device Most damages are the result of unprofessional operation The maximum ambient temperature 40 degree must never be exceeded Please consider that unauthorized modifications on the device are forbidden due to safety reasons www colorbeam com OPERATION Attention It is import to read this manual before you install or use this product NL color gon t B wr yea POWER ON OFF 1 Power ON OFF G Press the circle with ON OFF letter on the panel to turn th
11. through the metal backplate and tighten the plate on the wall with 4 screws 2 Connect the wires to the customized terminal block in accordance with D D GND 3 Place Orbit TP the metal backplate NOTICE 1 Please notice the idea of the wiring for all Colorbeam fixture is in series connection 2 he warranty will be invalid when the fixture is not under normal usage including trimming the cable and do wiring by user Please contact with your sales representative for the detailed information if the trimming will be happen eri www colorbeam com Read the instructions carefully before you install or powering CAUTION Be careful with your operations You can suffer a dangerous electric shock when touch the wires inside the unit 1 Safety Instructions Every person involved with installation and maintenance of the this device has to be qualified following the instructions of manual Please make sure that there are no obvious transport damages Please immediately contact the local dealers as the device is in fault operation or damage Damages caused by the disregard of this user manual or unauthorized modification to products are not subject to warranty Important Keep this driver away from rain and moisture Unplug mains lead before opening the housing Make sure the plug is tightly connected with outlet Make sure all connector are connected properly Make sure the AC power that complie
Download Pdf Manuals
Related Search