T68 PAINTBALL MARKER
Contents
1. 2 Donotremove ortamper any labels on the marker Warranty will be voided if any part of the label is removed tampered or damaged Date 05 21 05 Page 2 T68 PAINTBALL MARKER Barrel Components Alignment Metal Handguard 1 Loosen 1 4 screws and remove 2 2 Loosen 3 in the rear cap to align the rear cap 4 3 Tighten all screws after re aligned 1 2 4 Fiber Handgua rd 1 Loosen 1 and 2 2 Align front sight and handguard 3 then tighten all screws Note The barrel is tightened by the strength of an individual user Applying more or less force each time may require realignment of the components 1 2 Bolt and Hammer Lubrication 1 Remove 1 upper 2 and lower 3 screws Slide butt assembly 4 to rearward 3 Remove hammer cushioning rubber and bolt by releasing upper and lower receiver knobs 4 Clean check and lubricate O rings of hammer and bolt 5 Replace O ring when it is required Always check the bolt pin is in tightened condition any loosen of the pin will cause the bolt and hammer stuck and the marker will have no any reaction when Date 05 21 05 Page 3 T68 PAINTBALL MARKER the trigger is pulled Insert hammer bolt into upper and lower receiver chambers Push cushioning rubber into lower receiver 1 4 inch 6 mm depth 8 Install upper and lower receiver 5 6 knobs Note During tightening and pushing inadvertent pushing of the hammer bolt and knobs will cau2. T68 PAINTBALL MARKER USER MANUAL Introduction T68 series patented paintball markers use 0 68 paintballs and provide the advanced and professional paintball marker systems to all users Thank you for using T68 Paintball Marker products Warning THE USER MUST READ THIS MANUAL PRIOR TO USE OF THESE PRODUCTS Warning Handle and operate this product with care to avoid any injury Copyright is reserved T68 Paintball Markers are patented All patented items have legal protection and any unauthorized copy will be prosecuted to the fullest extent of the law 1 This marker is intended for shooting paintballs unless otherwise labeled 2 This marker must be used by adults of 18 years or older only 3 Read the manual completely before using this product 4 This marker is not a toy It cancause injury to persons animal or objects nearby 5 Goggles and mask for eye and skin protection must be worn at all times during operation assemble cleaning and maintenance on this product 6 Do not point or fire the marker at any human animal and object Do not point or fire the marker at anyone that does not have the appropriate head throat eyes and body protection 7 This marker should only be used at a licensed and insured paintball field or designated training center When using this product obey all local laws and your country of operation If you are not sure Call the non emergency phone number listed for your local police departme
3. fication or conversion of any air pressure regulator part is prohibited 18 Do not damage or modify any part of this product 19 Handle with care when using this product all parts of the gun can cause injury if improperly used 20 Donotfire the marker to at any distance less than 25 feet or serious injury may result Date 05 21 05 Page 1 T68 PAINTBALL MARKER 21 Over tighten any screws will cause the thread destroyed 22 The O rings must be replaced after any part of component is removed 23 168 Paintball Marker is not responsible for any damage or personal injury when any part of the high pressure tube tube connector or the relevant air pressure system is removed or loosen or turned 24 Donot remove or tamper any labels on the marker Warranty will be voided if any part of the label is removed tampered or damaged General Operation Basic Steps Visit http rap4 com for addition service information 1 Push to safe 2 Install cylinder or remote adaptor 3 Push the safe from the other side 4 Pull charging handle 3 and ready to fire Adjust the velocity by turning the velocity screw Note Leave the velocity screw fully loosens and release the charging handle when the marker is not in use WARNING 1 T68 Paintball Marker is not responsible for any damage or personalinjury when any part of the high pressure tube tube connector or the relevant air pressure system is removed or loosen or turned
4. nt 8 Looking into the muzzle and bore is prohibited under any conditions 9 Be aware of unexpected human beings and animals intruding into the shooting area Clearing the shooting area before using the marker is mandatory 10 Keeping this product safely stored away from children This is mandatory when storing the paintballs cylinders cartridges marker and the relevant equipment 11 Packing the marker into a suitable carrying case is mandatory during transportation 12 When performing maintenance or repairing the marker the battery power must be turned off and magazine cylinder cartridge must be removed Magazine spring release switch must be pushed to release forwarder Magazine must not be loaded during maintenance or repair 13 Turn off and remove the battery power remove the cylinder or cartridge install a plug in the barrel and magazine release the charging handle and unload the paintballs is required when the marker is not in use 14 Always keep your finger or any objects away from the trigger assembly when the marker is not in the firing condition 15 Itis prohibited to modify convert or transform this product under any condition Unless noted otherwise professional repair or maintenance must be performed by a qualified technician 16 Do not damage the high pressure tube The high pressure tube can be damaged by striking or gashing Discontinue use if damaged as this may cause injury 17 Unauthorized modi
5. se the O rings to become worn or damaged If you are not sure or do not desire to perform this service we will do it for you 9 Drop silicon oil on the pressure tube end 7 is mandatory 10 Align tube and connector 8 then slide butt assembly to main body Caution Smoothly slide the base 4 to pressure tube 7 Inadvertently push will cause the O ring 9 damaged 11 Tighten the lower screw 3 first then upper screw 2 on regulator assembly base 4 Basic Maintenance The following items are required after one use 1 Check and secure all screws 2 Clean the bore upper and lower receiver chambers 3 Check and lubricate O rings on bolt and hammer WHEN DOING MAINTENANCE USE SILICON OIL ONLY ANY FLAMMABLE OIL WILL DAMAGE O RINGS Date 05 21 05 Page 4 T68 PAINTBALL MARKER REGISTRATION Congratulations You now posses a high powered paintball marker which when cared for will provide many years of enjoyment In order to receive authorized factory service please fill out this registration form and mail this form a long with your original purchasing receipt to T68 PAINTBALL MARKER 5151 Lafayette Street Santa Clara CA 95054 USA MODEL NUMBER SERIAL NUMBER DATE OF PURCHASE PURCHASED FROM YOUR NAME ADDRESS PHONE NUMBER EMAIL ADDRRESS Date 05 21 05 Page 5
Download Pdf Manuals
Related Search