GSM Terminal Manual - SeNd Technology Ltd
Contents
1. 07 Certification 07 SMS sed a hang 07 Data kaman Lan kae 07 i eae ee S 07 Supplementary services 08 Interfaces 08 Accessories 08 INSTALLATION 09 Package contents 09 Safety and Installation information 09 Mounting the GsmTerminal 09 Front view 10 INTERFACE DESCRIPTION 11 Power Supply 11 SIM card 12 EIA232 veg hana 13 Start Stop input 15 External Antenna type X 16 Internal Antenna type A 17 STARTUP 18 Shutdown 050 18 Permanent operation 18 Hardware controlled operation 18 Software controlled operation 18 OPERATING STATUS INDICATOR 19 Network search 20 Standby 20 Connected 20 COMMAND CONTROL 21 AT command control 21 Firmware Update 21 TRACKING MAINTENANCE 22 Tracking 22 Maintenance 22 Warranties 22 B1010eng GsmTerminal User Guide 4 Product description The GsmTerminal is an industrial GSM modem for the transfer of data SMS and faxes in GSM networks Industrial standard interface and an integrated SIM c2. 4 it s possible to control the GsmTerminal Closing the contact the GsmTerminal will be ignited and becomes operative after few seconds Opening the contact the GsmTerminal will be shut down immediately Leaving external contact open the GsmTerminal can be controlled by means of software control Any activity detected on the EIA 232 port will ignite the GsmTerminal that becomes operative after few seconds Sending specific AT SHDN command the module will be shut down immediately B1010eng GsmTerminal User Guide 18 Operating Status Indicator The light indicator on the front panel display the following operating states of GsmTerminal Operating state LED Indicator Power supply off OFF During startup sequence ON 8 Network search FLASHES RAPIDLY amp SIM card not installed PIN not entered GSM network unavailable Standby FLASHES SLOWLY registered in the network Connected ON data transfer in progress Shutdown 3 FLASHES WITH either hardware or software LONG INTERVAL e Usually the startup takes 1 2 seconds from power on or ignition signal amp The network search takes few seconds till the GsmTerminal is registered If the LED indicator continues to flash rapidly this means that no SIM card is inserted no PIN number is entered or no GSM network is available B1010eng GsmTerminal User Guide 19 Operating Status Indicator Network search In the network search state the GsmTerm
3. Scontrve KESEN Supplied by SeNd Technology Ltd T 08704 58 7363 F 07092 38 3861 www sendtech co uk USER GUIDE The information contained in this document are subject to change without notice Product names corporate names or titles used within this document may be trademarks or registered trademarks of other companies and are mentioned only in an explanatory manner to the readers benefit and without intention to infringe While every effort has been made to make sure the information in this document is correct Contrive can not be liable for any damages whatsoever for loss relating to this document Copyright 2002 CONTRIVE srl ITALY All Rights Reserved B1010ENG ISSUE 02 2002 B1010eng GsmTerminal User Guide 1 Safety Information Radio devices have limitations in the vicinity of electronic devices e Do not install the GsmTerminal near medical devices like pacemakers or hearing aids The GsmTerminal may interfere with the operation of these devices e Switch the GsmTerminal off when flying Secure it so that it cannot be switched on inadvertently fuel depots chemical plants or blasting operations when the GsmTerminal can disturb the operation of technical equipment e Do not install the GsmTerminal near petrol stations e Interference can occur if the device is used near RA televisions radios or PCs pu ar e In order to avoid possible damage we recommend that you only use
4. flashprogrammer software at this e mail address GsmTerminal contrive it B1010eng GsmTerminal User Guide 21 Tracking Maintenance Tracking Each GsmTerminal can be identified by its own IMEI number The IMEI number is printed on the front panel of the GsmTerminal The IMEI number is associated to each product resellers must keep information of customers and associated product IMEI number Maintenance Treat the SIM card with the same care as your credit card Do not bend or scratch SIM card or expose it to static electricity Do not use chemical cleaning agent on the SIM card and the GsmTerminal Do not remove any cover or label from GsmTerminal WARRANTIES Contrive guarantees for two years from the date of manufacture of its product to replace or at its option to repair any product or part thereof which is found defective in material or workmanship or which otherwise fails to conform to the description of its sales order Contrive makes no warranty of merchantability or any other warranty express or implied In no event shall Contrive be liable for consequential or special damages of any nature which may arise in connection with such products B1010eng GsmTerminal User Guide 22 G CONTRIVE CONTRIVE S r l 24040 SUISIO Bergamo via Enrico Fermi 18 TEL 39 35 4948236 FAX 39 35 4933759 GsmTerminal contrive it http www burner control com UK Agent SeNd Technology Ltd T 08704 58 7363 F 07092 38 3861
5. SC e The Terminal should be installed and set up only by qualified personnel e If a power supply unit is used to supply the GsmTerminal it must meet the demands placed on SELV circuits in accordance with EN60950 When using batteries and accumulators adhere to relevant regulations e The maximum permissible connection length between GsmTerminal and supply source is 3 m GsmTerminal can be installed on any standard EN 50022 rail by simple snap in A minimum protection degree IP40 must be guaranteed raised to IP54 for open air application B1010eng GsmTerminal User Guide 9 Installation Front view A DB rie af a ff Start Stop contact input EIA 232 interface LED status indicator Power Supply input SIM card holder RG174 cable stub with FME male jack type X only x MOOD gt B1010eng GsmTerminal User Guide 10 Interface description The following interfaces are available on the GsmTerminal e Connector for power supply e Connector for start stop contact input e Mini SIM card holder e EIA 232 interface V 24 V 28 Sub D 9 female e Antenna connector FME male type X Powersupply GsmTerminal receives its power supply from terminal 1 and 2 on the left of bottom side The voltage must be within 8 38 Vdc or 6 29 Vac Polarity reversal protection Since GsmTerminal can be supplied by direct or alternating current the power supply input is polarity independent Overvoltage protection Overvo
6. ard reader mean it can be used rapidly easily and universally as a dual band GSM Terminal Its performance bandwidth and the robust housing make it easier to quickly implement new applications in areas such as telemetry telematics and remote control The features functions and interfaces of the GsmTerminal are described below All the interfaces are integrated in the housing The connections are suitable for use in domestic and industrial environments Sg if PA 7 le li The GsmTerminal is based on proven RF technology By Telit Mobile Terminals S p A B1010eng GsmTerminal User Guide 5 Product description Highlights e Dual band EGSM900 GSM1800 e Data SMS and Fax e R amp TTE approval e Easy to integrate e Industrial interfaces e LED display e Standard industry and automotive voltage range e Highly compact light and powerful e Embedded omnidirectional antenna type A e External antenna connector type X Applications e Teleservice e Security systems e Telematics e Telemetry e Remote monitoring e Remote meter reading e Vending machines e Remote configuration e POS terminals e PDAs e Automotive application and Fleet Management B1010eng GsmTerminal User Guide 6 Features Product data Certification SMS Data Fax e Dual band EGSM900 and GSM1800 e Certified in accordance with GSM phase 2 2 e Output performance Class 4 2W for EGSM900 Class 1 1W for GSM1800 e Control via AT
7. commands e Power supply voltage 8 38 Vdc 6 29 Vac e Power consumption 3 W max e Operating temperature 0 55 C e EN 50022 rail 4 modules enclosure e Weight approx 180 g e Protection class EN 60529 IP40 properly fitted System could operate in extreme functional condition 10 C 65 C e R amp TTE approval Directive 1999 5 EG e Low Voltage Directive 73 23 EEC e EMC directive 89 336 EEC e Point to point MT Mobile Terminated e Point to point MO Mobile Originated e SMS cell broadcast e CSD up to 14400 bps e Group 3 classes 1 2 B1010eng GsmTerminal User Guide 7 Features Supplementary services Interfaces Accessories e Call Barring e Call Forwarding e Advice of Charge e Automatic Answer for Data and Fax e Calling Line Identification Presentation CLIP e Calling Line Identification Restriction CLIR e Closed User Group supplementary services CUG e Phone book e DTMF Dual Tone Multi Frequency e Power supply connector 2 5mm AWG14 e Start Stop input connector 2 5mm AWG14 e Antenna connector FME male type X e EIA 232 interface Sub D 9 female e Omnidirectional planar antenna e Directional high gain antenna e Power supply units e Interface converters B1010eng GsmTerminal User Guide 8 Installation Package contents Safety and Installation information Mounting the GsmTerminal e GsmTerminal 1010 00 00 e User Guide B1010eng e EIA232 cable 1 1 ICOC23
8. inal searches for a GSM network in order to register to main operator or to the roaming service provider Standby In the Standby state the GsmTerminal is registered in the network and ready to send and receive Paging is performed with the GSM network in order to obtain synchronisation with the GSM network Power consumption in this state depends on the current network availability It s possible to activate the energy saving function that reduces the power consumption during idle time see AT CFUN command Connected In this state a connection has been established between two subscribers via the GSM network Power consumption is at maximum and depends on the GSM network availability and several conditions hopping sequences antenna coupling B1010eng GsmTerminal User Guide 20 Command control AT command control The GsmTerminal is controlled and programmed by means of AT commands Full set of AT commands are available on the technical literature T1010eng Data transfer between host DTE and GsmTerminal during data transfer is limited to 14400 bps Data transfer between host DTE and GsmTerminal during command mode can reach 115200 bps The user can modify the data transfer rate by means of AT commands Factory default configuration is AUTOBAUD mode the GsmTerminal can automatically detect the host DTE data rate Firmware update The firmware update for the GsmTerminal takes place via the EIA232 interface Request the
9. ltages are suppressed by internal varistors on the power supply input Fuses An internal automatic fuse ensures electrical safety in the event of faults If an external protection should be provided connect a fast 1 5 A fuse on the positive line of the power supply Interference immunity e The cable length must not exceed 3 m e Max load current 1 5 A e Nominal signal range 0 40V e Electrical fast transient burst protection requirements in accordance with ETS 300 342 1 e Electrostatic discharge requirements in accordance with ETS 300 342 1 e Immunity RF common mode 0 15 80 MHz in accordance with ETS 300 342 1 e Voltage dips and interruption B1010eng GsmTerminal User Guide 11 Interface description SIM card The SIM card receptacle is intended for 3V SIM cards in accordance with GSM 11 12 phase 2 to operate the GsmTerminal The SIM card must be inserted in the card holder to put GsmTerminal into operation 1 Make sure that there is no voltage applied to GsmTerminal 2 Operate the eject mechanism yellow pin next to the card holder to open the card holder by pressing it down with a pen for example Ni 3 Insert the SIM card in the SIM card holder and push it back into the housing Interference immunity e Electrostatic discharge requirements in accordance with ETS 300 342 1 B1010eng GsmTerminal User Guide 12 Interface description EIA232 The EIA232 interface is the interface for the ap
10. nected to terminal 3 and 4 on the top left side Use any mechanical or electromechanical switch with 40V min 20mA min DC rating Polarity Using electronic switches the terminal 3 is the positive and terminal 4 is the input Overvoltage protection Overvoltages are suppressed by internal varistors on the start stop contact input Interference immunity e The cable length must not exceed 3 m e Nominal signal range 0 40V e Max load current 1A e Electrical fast transient burst protection requirements in accordance with ETS 300 342 1 e Electrostatic discharge requirements in accordance with ETS 300 342 1 e Immunity RF common mode 0 15 80 MHz in accordance with ETS 300 342 1 B1010eng GsmTerminal User Guide 15 Interface description External Antenna A dual band antenna GSM900 1800 must be type X connected to the RF interface available on the type model X The connection is implemented as a 50Q FME male coaxial jack at the end of a short RG174 cable stub exiting from the upper terminal side of the device Interference immunity e Electrical fast transient burst requirements cable gt 3m e Surge immunity requirements not specified e Electrostatic discharge requirements in accordance with ETS 300 342 1 e Immunity RF common mode 0 15 80 MHz in accordance with ETS 300 342 1 Purpose of the connections PIN Signal 1 0 Description Inner RF I O RF input output Outer GND X Frame connection B1010eng G
11. plication software and the connection to PC The customer application communicates with GsmTerminal by means of AT cellular commands The EIA232 interface is implemented as a 9 pin D Sub female socket with a screw fitting Interference immunity e The cable length must not exceed 1 8 m e Nominal signal range 15V e Max load current 1 e Electrical fast transient burst requirements not specified e Surge immunity requirements not specified e Electrostatic discharge requirements in accordance with ETS 300 342 1 e Immunity RF common mode 0 15 80 MHz in accordance with ETS 300 342 1 B1010eng GsmTerminal User Guide 13 Interface description Purpose of the connections PIN Signal 1 DCD 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI Input O Output I O Description O T 0 oF o l Zu 559 pdf NLE Wo a oz X Og NT Zz gt o ou 5209 x0 Zu Dm LL rog w W TB 0 Fs ke 0 Parameters gt 5V HIGH ACTIVE lt 5V LOW gt 5V HIGH LOGIC O lt 5V LOW LOGIC 1 gt 2 4V HIGH ACTIVE lt 1 8 LOW gt 2 4V HIGH ACTIVE lt 1 8 LOW ov gt 5V HIGH ACTIVE lt 5V LOW gt 2 4V HIGH ACTIVE lt 1 8 LOW gt 5V HIGH ACTIVE lt 5V LOW gt 5V HIGH ACTIVE lt 5V LOW B1010eng GsmTerminal User Guide 14 Interface description Start Stop input GsmTerminal receives the ignition signal from an external SPST contact con
12. smTerminal User Guide 16 Interface description Internal Antenna An internal dual band antenna GSM900 1800 type A is provided on the front panel of the type model A This internal omnidirectional antenna can work properly if the front side of the GsmTerminal is not shielded by metallic frames i e the GsmTerminal is installed inside a metal cabinet Interference immunity e Electrostatic discharge requirements in accordance with ETS 300 342 1 e Immunity RF common mode 0 15 80 MHz in accordance with ETS 300 342 1 B1010eng GsmTerminal User Guide 17 Shutdown Permanent Operation Hardware Controlled Operation Software Controlled Operation Before startup the external components must be connected The SIM card must be inserted in a deenergized state GsmTerminal is ready for operation when supply voltage is applied and the ignition contact is closed The GsmTerminal starts the network search and registers with network operator Please read the following conditions for switching the GsmTerminal on and off When the light indicator flashes 3 times with long interval between the GsmTerminal is powered but not operative To let GsmTerminal operate continuously put a wire jumper between terminal 3 and 4 At each power on the ignition sequence will take place and after few seconds the light turns into slow flashing and the terminal becomes operative Using an external SPST contact connected to terminal 3 and
13. the specified accessories These have been tested and shown to work well with GsmTerminal However the warranty does not cover these accessories The warranty does not apply in the event of improper use B1010eng GsmTerminal User Guide 2 Safety Information GsmTerminal is not authorized for use as critical component in life support devices or systems unless a specific written agreement regarding such intended use is entered into between the customer and Contrive prior to use Life support devices or systems are devices or systems intended for surgical implantation into the body or to sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labelling and user s manual can be reasonably expected to result in significant injury No complex software or hardware system is perfect Bugs are always present in a system of any size In order to prevent danger to life or property it is the responsibility of the system designer to incorporate redundant protective mechanisms appropriate to the risk involved All GsmTerminals are 100 functionally tested Specifications are based on characterization of tested sample units rather than testing over temperature and voltage of each unit B1010eng GsmTerminal User Guide 3 PRODUCT DESCRIPTION 05 Highlights 06 Applications 06 FEATURES 07 Product data
14. www sendtech co uk info sendtech co uk B1010eng GsmTerminal User Guide 23
Download Pdf Manuals
Related Search