user`s manual
Contents
1. you will see the following information About TOSHIBA dynadock Utility TOSHIBA dynadock Utility Version 1 00 00 Copyright C 2006 2008 TOSHIBA Corporation Al rights reserved Le Sample Image About dynadock utility EN 42 User s Manual dynadock Specifications This section summarizes the dynadock s technical specifications Physical Dimensions Weight About 490g 17 2 ounces including the Base Size 42 w x 77 d x 222 h mm 1 7 w x 3 0 d x 8 7 h not including the parts that extend beyond the main body 112 5 w x 130 d x 234 h mm 4 4 w x 5 2 d x 9 3 h including the Base Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C to 35 C 41 F to 95 F 20 to 80 Non operating 20 C to 65 C 4 F to 149 F 10 to 90 Thermal Gradient 20 C per hour maximum Wet bulb Temperature 26 C maximum Power Requirements AC adaptor 100 240 volts AC 50 60 hertz cycles per second 15V DC 3 0 4 0 amperes different for each model User s Manual EN 43 dynadock General Specifications Computer Interface USB 2 0 Ports and Connectors 4 USB 2 0 ports in the back 2 USB 2 0 Powered ports in front 1 x S PDIF optical digital audio output 1 x Ethernet Port 10 100 Base T Ethernet RJ 45 connector VGA x 1 Analog D SUB 15pin Female Connector DVI D x 1 Digital 24 pin2. Output Device Petabade CS 5 D gt Analog Output XM Gd 2 O OL ex O JUUL SIPDIF Output ant Digital Audio 48 KHz Ir 2cH nnn Audio System Status Sample Image S PDIF selection 4 Configure the Audio Output setting of your DVD playback software to use S PDIF Access the software s setup or configuration panel to locate the Audio Out item EN 28 User s Manual dynadock Video Port VGA and DVI Connection The dynadock has both the following types of video ports VGA for connection to VGA interface monitors DVI for connection to DVI interface monitors NOTE Only one monitor can be connected to the dynadock Although the ports and video drivers are different the connection and setup is the same Connect the monitor cable not provided to the video output port on the dynadock and the external monitor This cable can be connected and disconnected any time without disconnecting the dynadock from the USB port on your computer NOTE The dynadock should be connected to a USB 2 0 port for optimal video performance The dynadock will work when connected to a USB1 1 port however video performance will be compromised The USB connector may be plugged and unplugged while the dynadock is on You can customize the video settings of the dynadock See Adjusting Video Settings for more information Viewable screens The dynadock video drivers give you the option of v
3. TOSHIBA Corporation Updates gt Screen Resolution Color Quality Screen Rotation Extend To gt o Extend Mirror Off Sample Image display mode change screen 4 On the Display Settings screen click Advanced Settings Windows Vista Advanced Windows XP and then click Monitor r E TOSHIBA Video Dock USB_0111 0000000000000000 and Mo TOSHIBA Video Dock USB_0111 0000000000000000 2 fX Gi Intel R Graphics Media Accelerator Driver for Mobile General Adapter Monitor Troubleshoot Color Management Adapter Monitor Troubleshoot Color Management Monitor type Monitor Type A TOSHIBA Video Dock USB 0111 0000000000000000 a TOSHIBA Video Dock USB_0111 0000000000000000 Monitor settings Monitor Settings Screen refresh rate Screen refresh rate 60 Hertz ai h l OK JI Cancel J Apply Windows Vista Windows XP Sample Image display setting screen 5 Select a refresh rate from the Screen refresh rate pull down list Be sure to select a refresh rate that is supported for the resolutions and color depth settings as indicated in the table above Then click OK 6 Click OK to close the Display Settings screen If you use multiple dynadocks with a single computer for example one at work and one at home the video settings for each dynadock are saved when you disconnect the computer This enables you to have your dynadock set up with differe
4. CD into your optical disc drive It will run automatically and the dialog box will appear If the auto run function is disabled on your system the program will fail to load automatically Please open the disk in Windows Explorer and double click AutoRun exe NOTE You may need to temporarily disable spyware or anti virus programs while installing the drivers It is also recommended that all other applications are closed as you will need to restart your computer after the drivers are installed You need administrator privilege to install uninstall the utility and drivers 2 Click on Setup to open the dynadock USB Installer The dynadock USB installer enables you to easily install uninstall or update the driver dynadock Install Menu 1 0 0 0 Tosa DES Setup E E nd J Instal Adobe Reader 8 Ext TOSHIBA Sample Illustration dynadock Install Menu User s Manual EN 15 dynadock 3 Click the Install button to install the selected programs The Status area in the right center of the screen indicates the drivers installed dynadock USB installer Select the programs to installuninstal Iv dynadock Utility Iv Network Driver W Audio Driver IV Video Driver Detailed Status Information pe Install Cancel Sample Illustration dynadock USB Installer The following drivers are installed during the installation process Driver Type Driver Name E dynadock Util
5. Shifter controls See page 26 for the SHIFTER Control window sample image NOTE In order to use the S PDIF function in Windows Vista select Start gt Control Panel gt Hardware and Sound gt Sound In the Playback tab set the Digital Output as default device EN 24 User s Manual dynadock Windows XP Operations 1 In the Analog Output section select headphone icon Wd USB Multi Channel Audio Devi a ge Main Setting Mixer Effect Karaoke Magic Voice Inl Output Device 5 LA Analog Output L X zw mU ewe Sample Image Select headphone 2 Onthe panel click the 7 1 Virtual SPEAKER SHIFTER button to enable the virtual multi channel function The icon will turn blue when selected formation DSPMode Sample Image 7 1 Virtual SPEAKER SHIFTER button 3 The button next to DSP Mode string allows you to switch between the SHIFTER control and basic control window formation _ DSPMode Sample Image DSP button Click on the Virtual Speaker Shifter button open the Shifter controls See page 26 for the SHIFTER Control window sample image User s Manual EN 25 dynadock Using the Virtual Speaker Shifter Controls for both Windows XP and Windows Vista 1 evi os Volume control Rotate all the virtual speakers clockwise Rotate all the virtual speakers counterclockwise Manually rotate all the virtual speakers Manual shifting functi
6. device below to modify its settings Speakers E ET Digital Output Speakers Realtek H Configure Speakers e Working Sound playback 9 Default device D SoundMAX Digital Audio Volume E Sound recording A Default device 1 SoundMAX Digital Audio Test Disable olume MIDI music playback Sis Default device 2222 Microsoft GS Wavetable SW Synth Volume About Use only default devices Show Disabled Devices Show Disconnected Devices About Software MIDI Synthesizer Properties Configure Windows Vista Windows XP Sample Image Change Sound Device screen Select Update Support Choose the Update support option User can receive the update information from the e mail used for registration There would be a dialog to prompt user Update Support TOSHIBA dynadock URI For updated drivers FAQ information and other dynadock information please go to User Support USA http www dynadock com User Support EU http computers toshiba europe com User Support Other regions http www pc support global toshiba com User Registration and Update http www csd toshiba com cgi bin tais su su sc notifyList isp Notification USA Sample Image Support information User s Manual EN 41 dynadock Select Help If you select Help the online user manual opens Select About If you select About
7. or right click the icon in the system tray notification area Sample Image system tray notification screen 2 Select Extend from the menu Updates Screen Resolution Color Quality Screen Rotation Extend To gt Extend Mirror Off Advanced Sample Image display mode change screen NOTE Depending on your computer and operating system you may need to uncheck the Extend my Windows desktop onto this monitor box in Display Properties when the dynadock is disconnected EN 30 User s Manual dynadock Switching from Extended Mode to Mirror Mode Follow these steps to change the video output to Mirror Mode 1 Click or right click the icon in the system tray notification area Sample Image system tray notification screen 2 Select Mirror from the menu TOSHIBA Corporation Updates gt Screen Rotation Extend To Extend Miror Off Advanced ENT Lr Sample Image display mode change screen NOTE You can also use the Windows Display properties screen to switch between Extended Mode and Mirror Mode User s Manual EN 31 dynadock Adjusting Video Settings There are three components that make up the screen mode Resolution In common usage this refers to the number of pixels displayed on the screen horizontally and vertically Color Depth This defines the number of different colors that can be shown on t
8. s Manual EN 17 dynadock Connecting the dynadock to the Computer 1 Plug the AC adaptor cord cable into the DC IN on the back of the dynadock Sample Illustration Connecting the AC adaptor cord to the dynadock 2 Connect the AC Power Adaptor with the AC power cord cable and then connect the AC power cord cable to a live electrical outlet The power indicator on the front panel glows blue when the dynadock is powered on 3 Plug the square end of the USB cable into the USB upstream port on the back of the dynadock Sample Illustration Connecting the USB cable to the dynadock EN 18 User s Manual dynadock 4 Plug the other end of the USB cable into an available USB 2 0 port on your computer Sample Illustration Connecting the USB cable to your computer NOTE Some computers may not immediately recognize the dynadock is connected upon start up This is not malfunction of the dynadock it is related to the computers BIOS start up sequence lf this occurs follow the steps below 1 Turn off the computer 2 Disconnect the dynadock from the computer 3 Turn the computer back on 4 Connect the dynadock to the computer once the computer s operation system has loaded Please note these steps may need to be repeated every time you start the computer User s Manual EN 19 dynadock Uninstalling To remove the dynadock Utility and all the drivers from your computer p
9. EE EE rtr Rr RES 40 Select Update Support aii ence dec tienen rinanta 41 leg jo RR 42 select About nom er aree pat ep bide ee AEG 42 DPOCITICAHONS cd CE 43 EN 2 User s Manual dynadock Regulatory Compliance FCC Information FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures EH Reorient or relocate the receiving antenna E Increase the separation between the equipment and receiver W Connect the equipment into an outlet on a circuit different from that to which the receiver is connected E Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications made to this equipment no
10. EH Never leave small parts such as covers caps and screws within the reach of infants or small children Swallowing a small part may cause choking and suffocation resulting in death or serious injury If a part is swallowed immediately take appropriate emergency action and consult a doctor Avoid liquids moisture and foreign objects E Never allow any liquids to spill into any part of your product and never expose the product to rain water seawater or moisture Exposure to liquid or moisture can cause electric shock or fire resulting in damage or serious injury If any of these eventualities should accidentally occur immediately 1 Turn off the product 2 Disconnect the AC adaptor from the power plug socket and product Do not turn on the power again until you have taken the product to an authorized service center Failure to follow these instructions could result in serious injury or permanent damage to the product Never place your product in locations with excess heat E Never place your product where it will be exposed to excess heat such as in direct sunlight an unventilated vehicle or near a heater This may result in a system failure malfunction loss of data or damage to the product User s Manual EN 7 dynadock Never place your product in a location with extremely low temperatures E Never place your product in a location where it will be exposed to extremely low temperatures This may result in a sys
11. Female Connector 1 x microphone 3 5 mm mono audio in 1 x headphones 3 5 mm stereo audio out 1 x line out 3 5 mm stereo audio out 1 x DC in plug 1 x Cable Lock Slot Supported Video Display Modes Depending on operating system Windows XP Mirror Desktop Extended Desktop Primary Display Windows Vista Mirror Desktop Extended Desktop Primary Display Some built in video adapters may prevent a second monitor from being the primary display Specifications are subject to change without further notice EN 44 User s Manual
12. GA or DVI component first starts it will extend the primary monitor Changes to the screen mode and VGA or DVI component operation mode can be made under the Windows display properties If no output is seen on the monitor connected to the VGA or DVI component it may be in a mode which cannot be displayed by the monitor This can happen if the monitor does not report its supported modes to the VGA or DVI component Reduce the resolution of the primary display and in turn the resolution of the VGA or DVI component display until an image is shown NOTE Placing the monitor into an unsupported mode for long periods can damage it Adjusting the Video Settings for the monitor connected to the dynadock 1 Click or right click the icon in the system tray notification area Sample Image system tray notification screen 2 Tochange the screen resolution or color quality select those options on the screen Be sure to select one of the supported resolutions and color quality numbers in the table above For an external monitor you can also select any resolution or color quality supported by that monitor Updates b Screen Resolution Color Quality Da Screen Rotation Extend To gt Extend Mirror Off Advanced Sample Image display mode change screen User s Manual EN 33 dynadock 3 To change the refresh rate select Advanced from the menu this will open the Windows Display Properties
13. User s Manual dynadock TOSHIBA Leading Innovation gt gt gt dynadock Contents WTOC UCTON E 11 FO AUIS is 11 gocce H 12 Back panel 2 21 25 5 nnn ii eee I Re EE E 13 Uil M 14 Computer Requirements ssessseeee emen 14 p crc 14 hcm 15 Installing the Drivers eiecit enitn entem innen 15 Background Utility Program eseen 17 Connecting the dynadock to the Computer 18 Uninstalling m R 20 Using the dynadock ear eem enne nnns 21 IU olore dolio 21 USB2 0 POMS ies nete napi o netter Mieres 22 Ethernet Prt e n 22 MICFOPNONG POM e 23 Headphone Port 1 n ren tH EE Mr Rs ieee 23 Stereo lineout port ioci riter tton eene negem 23 Video Port VGA and DVI nennen 29 How Standby Sleep or Hibernation Mode Affects Devices Attached to the dynadock TM reatar 35 Using the dynadock Utility 22 1 cc e ccscceseeseceedeseceeeseceseeseeeedeeeeseeeeseneeeee 35 labs M 35 Eject Dock and Slgep se saum eie cite rte i 37 Changing the dynadock Utility Settings 38 Select Audio Device irte PED
14. ce peripherals through one USB cable to just about any Windows based notebook The dynadock is software upgradable to enable you to keep your dynadock in line with technological advances Visit dynadock com for the latest software driver support updates Single USB cable connection to your computer Upright slim design saves desktop space Easily accessible ports located on the front Supports resolution up to 1920 x 1200 VESA CVT standard Video Electronics Standards Association Coordinated Video Timing video on external monitor Hot swappable you can add or remove most devices without rebooting the computer Virtual 7 1 channel surround sound Includes all video and audio drivers to get you started Please visit www dynadock com for the latest software driver updates Includes TOSHIBA dynadock Utility to customize dynadock settings Charges your USB peripherals with the front powered USB ports The undock button allows you to easily and safely dock and undock the dynadock from your computer User s Manual EN 11 dynadock Front panel DC IN LED Glows blue when power is being correctly supplied from the AC power adaptor 5 Status LED Indicates the status of docking undocking o and charging functions Docking Flashes green during the docking process glows green when docked Undocking Flashes orange during the undocking process stops flashing orange when undocked Charging Glows orange whe
15. ce to optimize your audio effects Most of the settings can be adjusted using the available sliders images or buttons Just make the adjustments to suit your personal preferences NOTE You can connect the headphone or the speaker to the headphone port however the lineout port has the audio higher quality for the external Speaker Using Virtual 7 1CH Function on 2CH Speakers headphones The audio output port is used to connect stereo speakers or headphones Although 2CH speakers may be connected a virtual 7 1CH surround sound experience is possible using the software s virtual multi channel function To enable the virtual 7 1CH audio function on 2CH speakers or headphones User s Manual EN 23 dynadock Windows Vista Operations 1 Inthe Analog Output section select headphone Output Mode Analog Output Output Device 2 Speakers Digital Audio 48 KHz q 3 S PDIF Output Pem Sample Image Select headphone 2 Onthe panel click the 7 1 Virtual SPEAKER SHIFTER button to enable the virtual multi channel function The icon will turn blue and a mark will be shown in the rightside window when selected DSP Mode LS DSP Effect Sample Image 7 1 Virtual SPEAKER SHIFTER button 3 The button next to DSP Mode string allows you to enter the SHIFTER control window DSP Mode ES Virtual Sample Image DSP button Click on the Virtual Speaker Shifter button to open the
16. dynadock Handling the AC adaptor and power cables cords or plugs When handling the power cable cord follow these precautions Never tamper with the power cable cord or plug Never splice or alter a power cable cord Never bend or twist a power cable cord Never pull on a power cable cord to remove a plug from a socket Always grasp the plug directly Never place heavy objects on a power cable cord Never run a power cable cord through a pinch point such as a door or window Never place a power cable cord near a heat source Never use nails staples or similar objects to fasten or attach cord in place Never attempt to disassemble or repair an AC adaptor Doing any of the above may damage the cables and or result in a fire or electric shock possibly resulting in serious injury Attaching the power cable cord Always confirm that the power plug and extension cable plug if used has been fully inserted into the socket to ensure a secure electrical connection Failure to do so may result in a fire or electric shock possibly resulting in serious injury Be careful if you use a multiple connector An overload on one socket could cause a fire or electric shock possibly resulting in serious injury Dust on the power plug connectors or connector base If dust gets on the power plug connectors or connector base turn the power off and disconnect the power plug Then clean the connector and or connector base with a dry c
17. he screen at the same time Refresh rate Measures the speed that the entire screen is rescanned Higher frequencies reduce flicker Below is a list of refresh rates supported at various resolutions and color depths for the VGA and DVI component Color Resolution Depth 640x480 800x600 1024x768 1280x768 1280x960 1280x1024 16 bit 60 7275 566072 607075 607585 6085 60 75 85 75 85 85 32 bit 60 7275 566072 607075 607585 6085 60 75 75 85 85 1280x800 1440x900 1600x1200 1680x1050 1920X1200 16 bit 60 60 60 60 60 32 bit 60 60 60 60 60 Note that interlaced modes are not supported and the resolutions listed above may not be supported by your monitor Additional modes may be offered depending upon the connected monitor but these are not currently guaranteed If the monitor does not advertise the supported modes the VGA or DVI component will choose a set of common screen modes If cloning the primary display the VGA or DVI component will try to use the preferred monitor mode In some cases this may not be the most appropriate mode for the mirrored desktop It is recommended that the primary display resolution be changed to closer match the default resolution of the dynadock monitor NOTE For more information on supported modes be sure to check the documentation supplied with your monitor EN 32 User s Manual dynadock Initial Use When the V
18. he use of this product in these working environments is maybe restricted or cannot be recommended Possible consequences of the use of this product in non verified working environments can be Disturbances of other products or of this product in the nearby surrounding area with temporarily malfunction or data loss corruption as result Example of non verified working environments and related advices Industrial environment e g environments where a mains voltage of 380V three phase is being used mainly Danger of disturbances of this product due to possible strong electromagnetic fields especially near to big machinery or power units Medical environment The compliance to the Medical Product Directive has not been verified by Toshiba therefore this product cannot be used as a medical product without further verification The use in usual office environments e g in hospitals should be no problem if there is no restriction by the responsible administration This product is not certified as a medical product according to the Medical Product Directive 93 42 EEC Automotive environment Please search the owner instructions of the related vehicle for advices regarding the use of this product category Aviation environment Please follow the instructions of the flight personnel regarding restrictions of use EN 4 User s Manual dynadock Additional environments not related to EMC Outdoor use As a typical home office equ
19. iewing a total of three screens 1 The screen on the notebook 2 An external monitor connected to the video port on the notebook if available 3 An external monitor connected to the dynadock NOTE The external monitor connected to the dynadock may be identified as either 2 or 3 on the Windows Display Properties screen depending on your model although there may not be a total of 3 viewable screens Video Modes The dynadock video output works in two modes E Mirror Mode B Extended Mode User s Manual EN 29 dynadock Mirror Mode This mode mirrors creates an identical display from your computer screen to the external monitor This is useful for example if you want to use a larger desktop monitor rather than the computer screen In Mirror Mode the dynadock automatically selects the settings screen resolution color quality and refresh rate for the external monitor that will allow the best resolution based on your computer s settings Extended Mode Extended Mode lets you split your display across multiple monitors This provides a number of advantages to increase productivity EH View your large spreadsheets across two or three screens with display continuity EH Multitask more effectively without overlapping windows E Compare two documents simultaneously across two three screens EH View videos TV on one screen and reviews on the other Set up the dynadock for Extended Mode 1 Click
20. ipment this product has no special resistance against ingress of moisture and is not strong shock proofed Explosive atmosphere The use of this product in such special working environment Ex is not allowed WEEE Information Following information is only valid for EU member States Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste The black bar indicates that the product was placed on the market after August 13 2005 By participating in separate collection of products you will help to assure the proper disposal of products and thus help to prevent potential negative consequences for the environment and human health For more detailed information about the collection and recycling programmes available in your country please visit our website http eu computers toshiba europe com or contact your local city office or the shop where you purchased the product FC CE x Safety Instructions Always read the safety instructions carefully Do not disassemble modify tamper with or repair your product E Do not attempt to disassemble modify tamper with or repair product including AC adaptor Disassembly modification tampering or repairing the product could cause fire or electric shock possibly resulting in serious injury Please contact an authorized Toshiba service provider for any repair service User s Manual EN 5
21. ity dynadock Utility II W Network Driver AX88772A amp AX88772 W Audio Driver USB Multi Channel Audio Device E Video Driver DisplayLink Core Software TOSHIBA dynadock In addition these icons are added to the Notification Area System Tray La Toshiba dynadock Utility E USB Multi Channel Audio Device pee DisplayLink Core Software EN 16 User s Manual dynadock 4 Follow the on screen directions to finish the installation If there s any previous version installed dynadock setup package will auto detect the installed version and pop up the following screen Please follow the on screen directions to finish the installation TOSHIBA Select the programs to install uninstall IV dynadock Utility dynadock USB installer dynadock setup has detected previously installed drivers Click Yes to remove the drivers and update dynadock Click No to cancel the update Yes No i Select All Detailed Status Information Uninstall Install Cancel Sample Illustration Updating Screen Background Utility Program After the dynadock utility is installed and the computer is restarted a program named TOSDockApp exe will run automatically in the background It can be viewed in the Windows Task Manager The program detects the insertion and removal of the dynadock NOTE The utility program does not impact any other programs on your computer Please do not turn it off User
22. lease follow the following procedures NOTE a gt HG Before starting the steps below you must eject the dynadock from your computer using the undock button or TOSHIBA dynadock utility icon on your Notification Area System Tray Disconnect the dynadock from the computer Any devices connected to the dynadock will be disabled Close all other programs and applications Do not use any other previous dynadock CD Open the uninstall screen by one of the following two ways Click Start gt All programs gt dynadock USB gt Uninstall dynadock USB or Insert the provided Installation CD into your optical disc drive It will run automatically and the dialog box will appear dynadock Install Menu 1 0 0 0 rosea rm Setup 3 Hana J Instal Adobe Reader 8 n Ext TOSHIBA Sample Illustration Initial Screen EN 20 User s Manual dynadock 2 Click on Setup on the above screen Then click Uninstall button to start to uninstall the programs you select dynadock USB installer TOSHIBA Select the programs to install uninstall IV dynadock Utiity Iv Network Driver Iv Audio Driver select all programs and dick the Uninstall button below Video Driver 1 dynadock Utility has been installed 2 Network Driver has been installed 3 Audio Driver has been installed Select All Detailed Status Information Uninstall Instal Cancel Sample Ill
23. loth Continuing to use the product without cleaning the power plug may result in a fire or an electric shock possibly resulting in serious injury Only use TOSHIBA AC adaptor Always use the TOSHIBA AC adaptor that was provided with your product that may have been provided with your product or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the product Use of an incompatible AC adaptor could cause fire or damage to the product possibly resulting in serious injury TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor or charger EN 6 User s Manual dynadock Use correct power source E Never plug the AC adaptor into a power source that does not correspond to both the voltage and the frequency specified on the regulatory label of the unit Failure to do so could result in a fire or electric shock possibly resulting in serious injury Only use approved power cables cords W Always use or purchase power cables cords that comply with the legal voltage and frequency specifications and requirements in the country of use Failure to do so could result in a fire or electric shock possibly resulting in serious injury Do not handle the power plug with wet hands EH Never attempt to connect or disconnect a power plug with wet hands Failure to follow this instruction could result in an electric shock possibly resulting in serious injury Choking hazards
24. n charging 2 USB 2 0 powered ports Connects and charges select USB peripherals for example PDA MP3 players and cell phones even when undocked 3 5 mm mono microphone input port For connection to an external mono microphone 3 5 mm stereo headphone output port For connection to stereo headphones Sample Illustration Indicators and connectors on the front of the dynadock EN 12 User s Manual dynadock Back panel JO ot JO 0 Lu umi Cor ie of q 3 5mm stereo lineout port For connection to stereo speakers Optical S PDIF digital audio output port Use an optical S PDIF cable not provided to connect to your digital audio equipment e g Dolby Digital Surround Sound receiver and speaker system To use this connection your receiver must have an optical S PDIF input 10 100 BASE TX Ethernet For connection to the Ethernet network via a network cable not provided 4 USB 2 0 ports A type female connector For connection to USB peripherals VGA video output port For connection to a VGA monitor Please note you can only use one video por
25. nd shall in no event be liable for any loss of profit or any commercial damage including but not limited to special incidental consequential or other damage March 2008 Rev1 0 Trademarks Intel Intel Core Pentium and Celeron are trademarks or registered trademarks of Intel Corporation Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries AMD AMD K6 Athlon and Duron are registered trademarks or trademarks of Advanced Micro Devices Incorporated Ethernet is a registered trademark and Fast Ethernet is a trademark of Xerox Corporation Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Other brands and product names are trademarks or registered trademarks of their respective companies User s Manual EN 9 dynadock Precautions for Microsoft Windows XP Microsoft Windows Vista The Fn F5 functionality detailed in the electronic User s Guide for your TOSHIBA computer only controls the internal video controller of your computer The TOSHIBA dynadock utilizes an advanced video graphics controller to display the video on the external monitor connected to it However due to USB 2 0 transfer speed limitations some or all portions of DVD playback may appear slow or choppy This is not a malfunction of the dynadock Move the vide
26. nt video settings for different locations The settings will be retained each time you use the dynadock with your computer EN 34 User s Manual dynadock How Standby Sleep or Hibernation Mode Affects Devices Attached to the dynadock External Monitors The external monitor connected to the dynadock will go blank if the computer goes into Standby Sleep or Hibernation Mode When in Mirror Mode the external monitor keeps the same settings it had before the computer went into Standby Sleep or Hibernation Mode once the computer returns to an active state When in Extended Mode windows that were previously on the external monitor will not move back to that external monitor once the computer returns to an active state Also if the external monitor is in Extended Mode and the computer requires a login after Standby Sleep or Hibernation Mode the login screen appears on the primary computer monitor not the external monitor This is consistent with Windows Operating System standards Other Devices If another device is connected to a port on the dynadock and the computer goes into Standby Sleep or Hibernation Mode that device will not function For example if you are using the Ethernet port for high speed network access network access will not be available until the computer returns to an active state Using the dynadock Utility Eject Dock When the dynadock is connected to your computer the TOSHIBA dynadock Utilit
27. o playback from the external monitor to your computer display for optimal video performance when viewing DVDs On Windows XP systems DVDs may not display correctly on an external monitor Use your computer s built in monitor to view DVDs This product does not support 3D programs In some software application programs that utilize certain directdraw commands such as some 2D Games the display on the external monitor connected to the dynadock will not be supported If you want to play these games in fullscreen we suggest you disconnect the dynadock This product is unable to enter full screen DOS mode when using the external monitor connected to the dynadock The internal speakers on your computer maybe disabled when the dynadock is connected See Select Audio Device section for further information The sound may be distorted or delayed when you play some media files If it couldn t be played normally we suggest you play it without connecting the dynadock Depending on your computer system you may receive a warning message if the external monitor connected to your dynadock is used as your primary display USB CPU resources mouse movement and other devices may be affected when playing movies or transferring large amounts of data via the dynadock EN 10 User s Manual dynadock Introduction Features Thank you for purchasing the Toshiba dynadock the universal docking station that enables you to connect your deskspa
28. ompt message User s Manual EN 39 dynadock Show unexpected remove message option lets users see a warning dialog box like the following when the user disconnects the USB dock directly HIBA dynadock Utility Warning You have unplugged or ejected dynadock without stopping it Unplugging or ejecting dynadock without first stopping it may cause your computer to crash and lose valuable data NOTE Be sure to use the same USB port on your computer every time you connect the dynadock otherwise you may need to restart your computer Don t show this message again Sample Image Warning message Select Audio Device Once dynadock is installed the sound on the notebook will be disabled enabling you to connect external speakers To re enable sound through your notebook please follow these steps 1 Click or right click the icon in the system tray notification area EBC O ac tan tom Sample Image system tray notification screen 2 Select Select Sound Device from the menu Eject Dock Eject and Slee Select Sound Device Update Suppo Settings Help About Sample Image Select Sound Device screen EN 40 User s Manual dynadock 3 Change the Sound playback default device to other than 3 USB Multi Channel Audio Device A Sound Sounds and Audio Devices Properties Playback Recording Sounds o Volume Sounds Audio Voice Hardware Select a playback
29. on You can drag a specific virtual speaker to the preferred position to enhance an individual channel output For example a low volume center for dialog can be enhanced by being dragged closer to you Reset the speakers to default settings Sample Image Shifter Controls EN 26 User s Manual dynadock Using the Basic Controls Windows XP only 1 To adjust reset the volume of the left and right channel of your speakers headphones 2 To test the left and right channel of your speakers headphones 3 Stops the audio test 1 t Sample Image Basic controls screen User s Manual EN 27 dynadock Digital S PDIF Output Windows XP only Using the S PDIF output function you can directly output the digital sound source from the computer to your home theater equipment without loss of sound quality To experience true digital sound quality 1 Make sure your DVD content supports Dolby Digital or DTS format 2 Make sure your external decoder AV receiver that connects to the dynadock supports Dolby Digital or DTS decoding capability 3 Turn on the S PDIF function in the USB Multi Channel Audio Device utility On the Main Setting tab of the utility click the button next to the S PDIF Output string and select Digital Audio 48KHz from the drop down menu Gd USB Multi Channel Audio Device ot Mains vetting Mixer Effect Karaoke Magic Voice Information
30. r s power is off When the charge function is active the Status LED will glow orange You can press the undock button to switch between charge and non charge TOSHIBA dynadock Utility Select the behaviors you want Undock Service IV Set charge mode after undock Notify Message v Show undocking complete message iv Show unexpected remove message Sample Image charge mode screen EN 38 User s Manual dynadock Notify Message Service The Notify Message Service shows warning messages when you undock the dynadock By default the boxes are checked NOTE TOSHIBA recommends that you do not uncheck these boxes If the boxes are unchecked there will be no warning messages if the dynadock is improperly ejected disconnected TOSHIBA dynadock Utility Select the behaviors you want Undock Service Iv Set charge mode after undock Notify Message IV Show undocking complete message IV Show unexpected remove message Sample Image Notify message service screen Show undocking complete message option lets users see a dialog box like the following to announce that undocking is successful IBA dynadock Utility Eject Dock is complete You can safely remove the dynadock from your computer NOTE Be sure to use the same USB port on your computer every time you connect the dynadock otherwise you may need to restart your computer Don t show this message again Sample Image Pr
31. red according to your network environment If you are unsure about the settings consult your network administrator for assistance NOTE The LAN port does not support wake up on LAN The Local Area Connection icon in the System Tray Notification Area will not show a connection Open Network Connections to view the Ethernet Connection EN 22 User s Manual dynadock Microphone Port To connect a microphone plug the 3 5mm microphone jack into the microphone input port Headphone Port To connect headphones plug the 3 5mm headphone jack into the headphone port After installing the provided audio software a USB Multi Channel Audio Device utility is installed in your computer It can be accessed by double clicking the USB Multi Channel Audio Device icon on the system tray notification area The icon may be hidden if the Windows operating system recognizes it as inactive Sample Image USB Multi Channel Audio Device NOTE Once dynadock is installed the sound on the computer will be disabled enabling you to connect external speakers For information on how to re enable sound through your computer see the Select Audio Device section on page 40 The USB Multi Channel Audio Device is not the default playback device after installation Stereo lineout port To connect external stereo speakers plug the 3 5mm speaker jack into the stereo lineout port The utility comes with a friendly graphic user interfa
32. t expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC Conditions This equipment has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3000 User s Manual EN 3 dynadock EU Declaration Comformity This product and if applicable the supplied accessories are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC and or the EMC Directive 2004 108 EC Responsible for TOSHIBA EUROPE GMBH Hammfelddamm 8 CE marking 41460 Neuss Germany Manufacturer Toshiba Corporation 1 1 Shibaura 1 chome Minato ku Tokyo 105 8001 Japan The complete official EU CE Declaration can be found at http epps toshiba teg com Working Environment Legal Text in EU Countries The Electromagnetic Compliance EMC of this product has been verified typically for this product category for a so called Residential Commercial amp Light Industry Environment Any other working environment has not been verified by Toshiba and t
33. t at a time DVI D video output port For connection to a DVI monitor USB Upstream Connector Connects and dynadock to the computer DC IN For connection to the provided AC power adaptor The dynadock always needs an external power supply for operation as it does not take power from the USB bus of the computer Cable Lock Slot Allows you to connect a cable lock to help prevent theft Sample Illustration Connections on the back of the dynadock User s Manual EN 13 dynadock Top panel Undock button Controls dock undock and charging functions For more detailed information see the Undock button section on page 21 Computer Requirements B 1 2GHz or higher processor Intel Pentium Celeron family or AMD K69 AMD Athlon AMD Duron family or compatible processor recommended Intel Core 2 Duo 2 0 GB or higher processor recommended for optimal video performance 512 MB memory or higher 1 GB memory or higher recommended USB 2 0 port 30 MB of available disk space Microsoft Windows XP 32bit edition with SP2 SP3 and Microsoft Windows Vista 32bit and 64bit edition with SP1 Assembly Slide the dynadock onto the base as shown below Sample Illustration Assembling the dynadock and base EN 14 User s Manual dynadock Installation Installing the Drivers 1 Insert the provided Installation
34. tem failure malfunction or loss of data Never subject your product to sudden temperature variations EH Never subject your product to sudden temperature variations This may result in condensation causing a system failure malfunction or loss of data Never place your product or AC adaptor on a heat sensitive surface E Never place your product or AC adaptor on a wooden surface furniture or any other surface that could be marred by exposure to heat since the product base and AC adaptor s surface increase in temperature during normal use W Always place your product or AC adaptor on a flat and hard surface that is resistant to heat damage Never operate your product during a thunderstorm EH Never operate your product on AC power during a thunderstorm If you see lightning or hear thunder immediately turn off the product An electric surge caused by the storm may result in a system failure loss of data or hardware damage EN 8 User s Manual dynadock Copyright Statement No part of this publication may be reproduced in any form by any means without prior written permission Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies Disclaimer Information in this document is subject to change without notice The manufacturer does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document a
35. th USB powered ports on the front of the dynadock These ports charge select USB peripherals for example PDA MP3 Players and Cell phones even when undocked NOTE When the dynadock is not connected to your computer or the computer s power is off only two front USB ports have the charge function The charge and non charge function depends on the charge mode setting in the dynadock utility See page 38 for setting the charge mode Not all devices can be charged through these ports USB 2 0 Ports Connect any USB device to one of the dynadock s six USB ports Wi f your USB device such as a printer or optical drive etc came with its own AC adaptor make sure that it is plugged into the device and a live electrical outlet Ethernet Port Connect one end of a network cable not provided to the Ethernet port RJ 45 on the dynadock and the other end to your network for high performance network access To configure the network properties of the Ethernet adapter In Windows Vista select Start gt Control Panel gt View network status and tasks gt Manage network connections In Windows XP select Start gt Connect to gt Show all Connections In the Network Connections folder double click the connection icon for the dynadock s Ethernet adapter which is indicated by ASIX AX88772A USB2 0 to Fast Ethernet Adapter This will open the Local Area Connection Properties window for you to configure the network settings as requi
36. the same USB port on your computer every time you connect the dynadock otherwise you may need to restart your computer Don t show this message again Sample Image Warning message CAUTION It is important that you correctly disconnect the dynadock by following the steps above Failure to do so may cause data loss and or damage to your computer and devices connected through the dynadock EN 36 User s Manual dynadock Eject Dock and Sleep When the dynadock is connected to your computer the TOSHIBA dynadock Utility can remove all devices and let the system sleep instantly with one click Please follow these steps 1 Click or right click the icon in the system tray notification area ee mmm Sample Image system tray notification screen 2 Point to Eject and Sleep and select Hibernation or Standby from the sub menu Eject and Sleep gt Select Sound Device Update Support Settings Help About Sample Image Eject and Sleep screen 3 Wait before removing the dynadock from the system Undocking now Sample Image Undocking screen If the dynadock is removed from the system successfully the icon in the system tray notification area will disappear If the dock is removed unexpectedly the software can detect this event and will give the user an Unexpected remove dialog box as shown below TOSHIBA dynadock Utility Warning You have unplugged or ejected dynadock wi
37. thout stopping it Unplugging or ejecting dynadock without first stopping it may cause your computer to crash and lose valuable data NOTE Be sure to use the same USB port on your computer every time you connect the dynadock otherwise you may need to restart your computer Don t show this message again Sample Image Warning message User s Manual EN 37 dynadock 4 After the dynadock is removed from the system successfully the system will go into sleep mode CAUTION It is important that you correctly disconnect the dynadock by following the steps above Failure to do so may cause data loss and or damage to your computer and devices connected through the dynadock Changing the dynadock Utility Settings The TOSHIBA dynadock Utility setting program allows users to change the Eject Dock setting Opening the Setting Dialog box 1 Click Start and then click Control Panel 2 Double click the TOSHIBA dynadock Utility icon Note If you can not find the TOSHIBA dynadock Utility icon please click classic view on the left of the control panel window 3 Setting dialog will appear Setting charge mode This will allow users to set the charge mode after the dynadock is disconnected from computer or the computer s power is turned off EH Check the Set charge mode after undock box to enable the USB charge function when the dynadock is disconnected from the computer or the compute
38. ustration Uninstalling Screen 3 Follow the on screen directions to finish the uninstall Using the dynadock You may connect devices to the appropriate ports on the dynadock while your computer is running A slight delay and display flickering is normal before the computer recognizes the new device NOTE You can also unistall the dynadock drivers from the control panel Undock button The Undock button enables you to easily and safely dock and undock the dynadock to from your computer and provides other convenient functions When the dynadock is docked to your computer Press the Undock button once to undock your computer and the dynadock To reconnect the dynadock and your computer press the Undock button again and it will reconnect When you press the Undock button the Status LED will flash orange during the undocking process and flash green during the docking process as listed below Docking Flashes green during the docking process glows green when docked Undocking Flashes orange during the undocking process stops flashing orange when undocked Charging Glows orange when charging User s Manual EN 21 dynadock When the dynadock is not connected to your computer or the computer s power is off Press the Undock button once to put the dynadock into charging mode The Status LED will glow orange when charging Press the Undock button again to stop the charging process This applies to bo
39. y can remove all devices with one click You can eject the dock by using one of the following two options Option 1 pressing the undock button 1 Press the undock button on the top panel once and the dynadock will undock TOSHIBA dynadock Utility P c Undocking now Eo Sample Image Undocking screen Note The status LED will flash orange When the undocking is finished the status LED will stop flashing Pressing this button again will re dock the computer to the dynadock User s Manual EN 35 dynadock Option 2 clicking the icon in the system tray notification area 1 Click or right click the icon in the system tray notification area oO utm rm Sample Image system tray notification screen 2 Select Eject Dock from the menu E Sleep gt Select Sound Device Update Support Settings Help About Sample Image Eject Dock screen 3 The dynadock will undock Undocking now Sample Image Undocking screen If the dynadock is removed from the system successfully the icon in the system tray notification area will disappear If the dock is removed unexpectedly the software can detect this event and will give the user an Unexpected remove dialog box as shown below Warning You have unplugged or ejected dynadock without stopping it Unplugging or ejecting dynadock without first stopping it may cause your computer to crash and lose valuable data NOTE Be sure to use
Download Pdf Manuals
Related Search