AIO571/573 Modules P7C Controller
Contents
1. and Acronysms List at the beggining of this document AlO57 1 573 n Ref PMU107001 Version 1 0 07 Release 10 20 10 70 User Manual P7C Controller Technical Specifications Power Supply Consumption Operation temperature Storage temperature Humidity Module weight Dimensions BAH tecnologia Automa o Industrial 5 Vdc supplied by main rack 0 7 W 0 to 60 C 25 C to 80 C lt 90 without condensation 0 06 Kg approximately 85 W x 83 H x 27 L mm Technical Data Input Output PT100 input Analog input Analog input protection Analog output Analog output protection Process Interface X1 process connector numbered from 1 to 8 X2 process connector numbered from 1to8 q d i L q a a i a i a a 4 L EFi 2 pt100 3 wires sensor channels with the standard operation range of 10 150 C Reading maximum error 0 5 full scale 4 10 bits resolution channels with option of connec tions with signals from 0 to 20 mA 4 a 20 mA im pedance of 125 Q and 0 to 10 Vdc impedance of 10 KQ Against overvoltage 2 10 bits resolution channels for signals from 0 to 20 mA1 or 4 to 20 mA Short circuit protected Gain adjust trimpots from pt100 channels Channels and supervison leds identifying pt100 inputs EO to E1 Channels and supervision leds identifying analog inputs from E2 to E5 Channels and supervision leds identifying analog2. is 10 to 150 C and full scale can be calibrated from 120 to 250 C The reading maximum error is 0 5 full scale The Pt100 second negative input must be connected to signal OV X1 5 The temperature values provided by the module for the Ladder program are set in Celsius degrees x 10 thus Standard Temp C Value obtained from Ladder program Description 10 to 150 100 to 1500 100 10 0 C 1500 150 0 C Utilisation examples of analog inputs of instrumentation 12 30Vdc 01 2 Wires Transmitter 02 3 Wires Transmitter Cable 03 4 Wires Transmitter Shielding Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors 1 Check the Notes and Acronysms List at the beggining of this document AlO571 573 Ref PMU107001 Version 1 0 07 Release 10 20 10 15 rae ta HI tecnologia Automa o Industrial User Manual P7C Controller Utilisation examples of analog outputs of instrumentation Current 20 mA 4 70 mA 124465 6 J0Vde Cable 7 Shielding 12 i Operation from 0 to 10V The analog input can operate on a range from 0 to 10V In this case the configuration from O to 20mA must be kept and it also must be closed the configuration strap associated to the output Strap J3 Related to S0 output Strap J4 Related to S1 output Others voltage configurations It is poss
3. outputs from SO to 51 d Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors 1 Check the Notes and Acronysms List at the beggining of this document AlO57 1 573 Ref PMU107001 Version 1 0 07 Release 10 20 10 71 att HI anil User Manual P7C Controller Connections The modules AlO571 573 have two process interface connectors identified as X1 8 terminal blocks and X2 8 terminal blocks These terminal blocks are numbered as the following tables will show X1 Terminal Block Signal 1 EO temperature sensor negative input EO temperature sensor positive input E1 temperature sensor negative input E1 temperature sensor positive input Analog inputs reference OV E2 analog input channel E3 analog input channel CON DO OO FB WwW ND E4 analog input channel X2 Terminal Block Signal 1 E5 analog input channel Analog inputs reference OV SO analog output channel SO analog output channel Analog outputs reference OV Analog outputs supply Analog outputs power supply reference CONDO OO FB WwW ND Cable shielding nected at the terminal blocks X2 6 24vdc and X2 7 OV amp IMPORTANT The analog outputs need an external 24Vdc power supply that can be con For analog signals use cables with shielding connecting them to the terminal block X2 8 1 Check the Notes and Acronysms List at the beggining of this docume
4. BA O Mal BR elo LE Automa o Industrial AI0571 573 Modules P7C Controller HI tecnologia B E1 tB E2 B E38 E48 E58 soa sn uv ive The content of this document is part of P7C User Manual PMU1070011 The Notes and Acronyms full list is at the complete version of the manual To get it please access www hitecnologia com br AR HI tecnologia User Manual P7C Controller Automa o Industral Al0571 573 Technical Specifications Presentation AlO571 573 are the P7C analog inputs outputs and pt100 channels modules providing to the user 4 analog inputs channels of 10 bits resolution configurable for current or voltage 2 analog outputs of 10 bits resolution and 2 channels with inputs for pt100 3 wires all them with individual leds to indicate the status leds Module with automatic addressing being allowed the simultaneous use of modules at P7C a P ka gt 4 gt r E a s y gt s t s Ww 2 amp z cy a s e a Nea eae 2224224 44444484 A T B Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors Compatibility The following table presents the CPU modules compatible with the modules used P7C Controller Module CPU300 CPU301 AlO571 Yes Yes AlO573 No Yes It must not be used with controllers that have 2 expansion racks 1 Check the Notes
5. E S O and 1 On Detected connec tion with the pro cess S O and1 Off No connection with Equipment turned off the process or parameterization fail of the analog module Condition Diagnosis S O0 and 1 On Detected connec tion with the pro cess S O and1 Off No connection with Equipment turned off the process or parameterization fail of the analog module Leds Status Condition DIETO LAKOXE S O0 and 1 On Continuously ON not depending on the output if it is connected to the process or not S O and 1 Off No 24V power sup Equipment turned off or ply module not operational Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors 1 Check the Notes and Acronysms List at the beggining of this document AlO57 1 573 Ref PMU107001 Version 1 0 07 Release 10 20 10 78 ao HI tecnologia User Manual P7C Controller 24Vdc module power supply Status Condition DIETO ALORI E 24V On There is analog out put power supply 24V Off Equipment turned off or module not operational 24V Blinking There is no analog output power supply Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors Dimensions mm 96 60 110 80 BEREREEE Eee rn U fU Product Part Number Part Number Identification 300 107 571 000 Module with 2 pt100 3 wires inputs 4 ana
6. er to unlock the plastic frontal At this moment pull them in order to remove them from the rack 1 Press the locks one against the other using the two hands it is not necessary to use a lot of force for that just the enough to unlock Each lock needs be moved at 3mm as indicated at the picture 2 With the locks pressed pull them in order to disconnect the module from the rack as indicated at the picture Configurations The analog inputs E2 E3 E4 and E5 are configurable by using a keys set available on a Dip Switch SW1 The access to the keys is at the module component face The others configurations of the module are executed using an specific software SPDSW Analog Input DIP8 Current Voltage SW1 E2 1 ON OFF 2 OFF ON E3 3 ON OFF 4 OFF ON E4 5 ON OFF 6 OFF ON E5 7 ON OFF 8 OFF ON IMPORTANT The current offset 0 to 20mA or 4 to 20mA is configured using SPDSW from the version 2 x xx on 1 Check the Notes and Acronysms List at the beggining of this document AlO57 1 573 n Ref PMU107001 Version 1 0 07 Release 10 20 10 74 ay HI tecnologia gt Industrial User Manual P7C Controller Pt100 Inputs utilisation examples The inputs E1 and EO connection scheme when connected to the sensor pt100 3 wires will be exemplified as it follows 2345678 In this case the PLC will be able to read the temperature at channels EO and E1 The standard range
7. ible to obtain other voltage ranges by using an external resistor as the following example shows By using a 2500 external resistor it is possible to obtain a range from 0 to 5V ATTENTION To use an external resistor keep straps J3 and J4 open Voltage 250 2 0 5V pa gt m p AE F 3 gt Cable Shielding 12 30Vdc 1 Extenal Resistor Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors 1 Check the Notes and Acronysms List at the beggining of this document AlO571 573 Ref PMU107001 Version 1 0 07 Release 10 20 10 76 AR HI tecnologia Automag o In i User Manual P7C Controller Process interface leds operation pt100 pies OHSA at the range from 10 to 150 C Leds Status Condition Diagnosis E 0 and 1 On pt100 sensor con Operational channel nected E O and 1 Off pt100 sensor nega Sensor fail discon tive input discon nected equipment nected turned off or analog module parameteriza tion fail Leds Status Condition Diagnosis E 2 and 5 On There is current sig Operational channel nal at the input E 2 and 5 Off There is no current Open channel equip signal at the input ment turned off or pa or current smaller rameterization fail of then the range con the analog module figured Analog inputs configured for current at the range from 0 to 20 mA Leds Status Conditio
8. log inputs and 2 analog outputs compatible with CPU300 301 300 107 573 000 Module with 2 pt100 3 wires inputs 4 analog inputs and 2 analog outputs compatible with CPU301 1 Check the Notes and Acronysms List at the beggining of this document A10571 573 n Ref PMU107001 Version 1 0 07 Release 10 20 10 79
9. n Diagnosis E 2 to On Note1 Operational channel E 5 FEZ to Off Inoperational chan Equipment turned off E 5 nel or parameterization fail of the analog module Note1 When the channel off set Current Voltage is zero the condition led on indicates that the channel is operational Analog inputs configured for voltage at the range from 2 to 10V Leds Status Condition Diagnosis E 2 and 5 On There is voltage signal at the input E 2 and 5 Off There is no voltage Open channel equip signal at the input ment turned off or pa or voltage smaller rameterization fail of then the range con the analog module figured Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors 1 Check the Notes and Acronysms List at the beggining of this document AlO57 1 573 n Ref PMU107001 Version 1 0 07 Release 10 20 10 TT HI tecnologia User Manual P7C Controller Analog inputs configured for voltage at the range from 0 to 10 V Leds Status Condition DIET ILORI E E 2 to On Note1 E 5 E 2 to Off Inoperational chan Equipment turned off E 5 nel or parameterization fail of the analog module Note1 When the channel off set Current Voltage is zero the condition led on indicates that the channel is operational Analog outputs configured for current at the range from 4 to 20 mA Leds Status Condition DIETS ILORI
10. nt AlO57 1 573 n Ref PMU107001 Version 1 0 07 Release 10 20 10 72 as Tike ologia User Manual P7C Controller Block Diagram yO BUS 2 Bus Interface 7 g 2 Local Processor Ni wy w cc Cc i a ez i ao o Outputs Temp Temp ED emess E5 SO Si OV 24V E0 E1 al Ground connector There are two ground connectors at the module side which are responsible for the contact with the main rack structure IMPORTANT When handling the module be careful to not hurt yourself with the ground con nectors because they have a sharp surface CALITION TE Els a cru Ez E E3 E Pa 5E my 50m 51 E Giu dy E Ty Compatible with the module AlO571 Note The modules can have lever connectors for the new modules or screw connectors Module Addressing The modules AlO571 573 have not addressing configuration using hardware strap switch It is provided automatically by the controller firmware when connected to the rack 1 Check the Notes and Acronysms List at the beggining of this document AlO57 1 573 Ref PMU107001 Version 1 0 07 Release 10 20 10 73 y D HI tecnologia User Manual P7C Controller Automa o Industral Removing the module from the rack AlO571 573 modules CAN be replaced with the device turned on Hot Swap To remove the module from the main rack push the two locks one against the oth
Download Pdf Manuals
Related Search