MV3-E Series Installation and Operation Manual for Hybrid Engine
Contents
1. for two years from the product manufacture date except where Teleflex Marine products are used commercially or in any rental or other income producing activity then this warranty is limited to one year from the date of original purchase for mechanical and electrical products Teleflex Marine Inc products found to be defective and covered by this warranty will be replaced or repaired at Teleflex Marine s option and returned to the customer Items must be returned freight prepaid within the warranty period to the dealer from whom such products were purchased or directly to Teleflex Marine Teleflex Marine s sole responsibility under this warranty is limited to the repair or replacement of product that is in Teleflex Marine s opinion defective Teleflex Marine is not responsible for charges connected with the removal of such product or reinstallation of replacement or repaired parts We will have no obligations under this warranty for any product which was improperly installed was used in an installation other than as recommended in our installation or operation instructions or specifications failed or was damaged due to an accident or abnormal operation including racing misuse or alterations outside our factory was repaired or modified by entities other than Teleflex Marine was used on an engine boat combination where the engine horsepower exceeds the rating established by the boat manufacturer was used with other pr2. provided with two positions for attaching the shift cable one for the standard travel and one for the longest travel Page 8 User Manual MV3 E Hybrid Controls Installation Throttle Wiring Harness Installation of the Wiring Harness A wire harness must be prepared for connection of the MV3 E control head to the engine TAC module Every boat is different and there may be several ways to route the harness Inside the boat there is often a channel or conduit used for wiring This can also be used to route the wire harness for the MV3 E control When routing the wiring harness care must be taken not to damage the cable insulation If a harness is short replace it with a correct length harness Don t add a short harness to make up the required length Run the harness over the shortest and straightest possible path Secure the harness every 2 feet 0 6 m with stainless steel screws and mounting head ties or clamps Excess harness length should be neatly coiled and secured with nylon ties The mounted harness should be as far as practical from high current wires or wiring runs and should not be subjected to water fuel lubricants or excess heat Preparation of the Control Head Wiring Harness Measure from the control head mounting location along unobstructed wire runs to the engine module Round measurement to the next whole foot and add additional length if uncertain Prepare harness as shown in the diagram on the next page It is recommended
3. ELPHI PACKARD P N 1 0 0 80 12124075 TAC MODULE CABLE SEAL 0 50 0 35 12124076 CABLE O D mm DELPHI PACKARD P N TAC MODULE CAVITY PLUG DESCRIPTION DELPHI PACKARD P N CAVITY PLUG 12059168 Page 10 User Manual MV3 E Hybrid Controls Installation Mount the Control 1 Run the cable which is connected to the control back to the shift location of the engine and drive 2 The cables should run as straight as possible avoiding any sharp bends Make no bends in the cable of less than 8 inch 203 2 mm radius 3 Shift the control into Forward to move shift arm out of the way This allows the control to be inserted into the cut out 4 When satisfied with the position of the control fasten the housing to the mounting surface with three 3 10 thread cutting screws One screw is 1 50 inches 38 1 mm 24 0 609 mm m edi Minimum Swivel P gt Bracket RA P Loose tie for cable movement Shift Cable Connection and Adjustment The shift cable must be connected so that the Forward Neutral and Reverse positions of the control shift lever will coincide with the forward neutral and reverse positions of the transmission lever Readjust the cable terminals until the correct function of the shift lever is achieved Proper adjustment of the shift cable will result in a much better operating control Overjamming the transmission stop on either end of the shift travel may I Cause exce
4. Meleflex MARINE MV3 E Series Installation and Operation Manual for Hybrid Engine Controls ISCHMV3E Revision 1 0 Notice to Boat Manufacturer Installer and Consumer Please read these instructions through carefully and entirely before beginning installation or operation This manual must be accessible to the owner user of this Teleflex Marine product Throughout this manual warnings are used to alert the installer operator to special instructions concerning a particular service or operation that may be hazardous if performed incorrectly or carelessly Observe these alerts carefully These safety alerts alone cannot eliminate the hazards that they signal Strict compliance to these special instructions when performing installation operation and maintenance plus common sense operation are the most effective accident prevention measures A WARNING This device should not be used as a navigational aid to prevent collision grounding boat damage or personal injury When the boat is moving water depth may change too quickly to allow time for you to react Always operate the boat at very slow speeds if you suspect shallow water or submerged objects This product contains lead a chemical known to the State of California to cause cancer birth defects and other reproductive harm Disassembly and repair of this electronic unit should only be performed by authorized service personnel Any modification of the serial number or att
5. empt to repair the original equipment or accessories by unauthorized individuals will void the warranty Handling and or opening this unit may result in exposure to lead in the form of solder The information contained in this manual is believed to be accurate at the time of going to print but no responsibility direct or consequential can be accepted for damage resulting from the use of this information The manufacturers reserve the right to make changes without notice to any of its products Page 2 User Manual MV3 E Hybrid Controls Table of Contents lineup P 4 Important Safety NOES Kc 4 Control iM ANE irc ivi 4 Moor e 5 Neutral Locking Rifle ae 5 Neutral Throttle Warm up Biblica 5 Installati n ee 6 Locate oro 6 Measuring the she 6 Inboards and ieri bee 6 Side Mount Cabling ARRE RR AEREA 7 Shift Cable Co nection Engine bidelli 8 Shift Cable Connection eil 8 Connect litbsdrodiso on site 8 Throttle Wiring A AGN SS vaso TEN E EE TOT LETS LTD 9 Installations OF the Wiring Haiti iaia 9 Preparation of the Control Head Wiring Halles 9 Connection ofthe Wiring miste 9 MV3 E Throttle Wiring Connections ae 10 Mount he COMTO RENE MR RE ETT 11 Shift Cable Connection and ACdjUStmMeht sse
6. ive instructions for shift cable connection Shift Cable Connection Control End Connect Shift Cable To Control 1 Insert shift cable through opening in hanger assembly in line with shift arm pivot attachment hole and lock cable in hanger slot 2 Screw pivot onto cable rod allowing threads to protrude through pivot 1 8 for standard travel or 1 4 for long travel 3 Lubricate pivot with grease then insert into required hole in shift arm Fasten with cotter pin Tighten cable nut against pivot Brass pivot Cable jam nut Cable rod 125 3 17 mm Standard travel 25 6 35 mm Long travel To obtain standard 2 3 4 inch cable shift travel at the engine use the shift arm on the control at the short pivot hole location For Mercury long 3 inch cable shift travel at the engine is necessary Assemble the shift arm to the control using longest pivot hole location CAUTION The pivot must be in the hole nearest to the cable entry end of the control Using the hole in the shift arm furthermost away from the cable mounting support will produce unequal shift travel between the neutral to forward and the neutral to reverse positions resulting in improper shift action NOTE The Control Shift Lever and the Transmission Shift Lever must coincide at the Forward Neutral and Reverse positions Different makes of transmissions my require different amounts of shift travel For this reason the Control Shift Lever is
7. oduct s which in Teleflex Marine s opinion are incompatible with the Teleflex Marine product THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF TELEFLEX MARINE AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL TELEFLEX MARINE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state Teleflex Marine products returned under this warranty must be tagged with the customer s name street address and phone number to ensure proper handling and returned freight prepaid to the selling dealer or to the appropriate Teleflex Marine manufacturing facility User manual contains the facility return addresses User Manual MV3 E Hybrid Controls Page 15 Ifeleflex MARINE Teleflex Marine 640 North Lewis Road Limerick Pennsylvania 19468 610 495 7011 www teleflexmarine com Teleflex Marine is a division of Teleflex Incorporated 2006 Teleflex Inc Page 16 User Manual MV3 E Hybrid Controls
8. s and the recommended clearance around and behind the mounting surface 2 Allow adequate clearance under the console or in the gunwale for the cables AND allow a minimum of 36 from the cable nest connection with no restraint When supporting the cables beyond 36 do not tie or clamp tightly 3 After a suitable location for the control is determined use the separate mounting template to make the cut out The templates are supplied with the control also see mounting dimensions on page 14 4 Closely follow the instructions provided on the template Cut and drill the mounting holes required Measuring the Shift Cable Measure the cable routing path from the control head connection to the engine connection To outboard or stern drive shift connection Inboards amp Stern Drives Measure from the control connection along an unobstructed cable routing to the SHIFT connection Round this dimension UP to the next whole foot and order the required cable part number Last two digits of the Teleflex cable number equal the length of the cable in feet NOTE To determine the correct control assembly for inboards with hydraulic transmissions you must determine if the Shift Cable pulls or pushes to go into forward Page 6 User Manual MV3 E Hybrid Controls Installation Side Mount Cabling User Manual MV3 E Hybrid Controls Page 7 Installation Shift Cable Connection Engine End See engine or stern dr
9. sserserserrsesrsrrrsrrrsrrrrrsrrrnrrsrrsr rs rr PER UG E ERI DUE IU AUNT ER DPI I E 11 Malllelilite E A E N E EE T 9 12 Maintenance and Corrosion Pilla 12 General Control Dimensions 13 Mounting DIMENSIONS sss ssssessssse ssssvs ssssas0v ssesesessssssesessovasessens esssss n vsssessesessassssessarssdess sessssesssasssesssesssessnsss 14 WALT AV 15 User Manual MV3 E Hybrid Controls Page 3 Introduction The Teleflex Marine MV3 E Control is designed to provide convenient one hand single lever operation of shift and throttle for most popular inboards equipped with hydraulic reverse gears and stern drives with MEFI V engine control module A safety feature of the MV3 E is a Neutral Locking Hand Lever It can only be disengaged from Neutral by raising the lifter under the ball knob The MV3 E accepts Teleflex Marine 33 style cables Important Safety Notices Teleflex Marine Controls highly recommends the installation and usage of an engine emergency shut off switch as an important safety feature for Class A and Class 1 boats This switch should be connected by a cord to the boat driver This shut off switch is not a standard part of the control you are using Control Configurations The MV3 E Control can only be mounted in a horizontal position WARNING Do not remove the hand lever to change position Page 4 User Man
10. ssive wear of the drive and the shift gear 2 Result in a heavy feel of the hand lever and or 3 Over stress and damage the cable User Manual MV3 E Hybrid Controls Page 11 Maintenance Maintenance and Corrosion Protection For maximum protection especially in a saltwater environment the control head and hand lever should be washed lightly with fresh water on a regular basis Periodically check the control head mechanism for loose fasteners and signs of wear on moving parts Keep moving parts well lubricated with a moisture displacing lubricant Periodically check the cables and engine connections for signs of wear and corrosion Replace as necessary Page 12 User Manual MV3 E Hybrid Controls General Control Dimensions Front View BLACK KNOB 3 10 18 1 it i CHROME HANDLE j M 2 15 69 9 MAX WALL THK 5 00 127 1 11 197 3 User Manual MV3 E Hybrid Controls Page 13 Mounting Dimensions MV3 E Side Mount Control Note These dimensions are NOT to scale When mounting use the template 311370E which is included with this control 4 04in 102 6mm R 1 00in 25 4mm 4 87in 123 7mm Page 14 User Manual MV3 E Hybrid Controls Warranty Teleflex Marine 2 Year Limited Warranty We warrant to the original retail purchaser that Teleflex Marine products have been manufactured free from defects in materials and workmanship This warranty is effective
11. that conductors be stranded tinned copper UL 1426 or equivalent 18 AWG min Colors shown are optional Connection of the Wiring Harness NOTE Always connect the wiring harness to the Control Head before connecting to the engine The engine connection should not be made until the control has been completely installed Ensure that the watertight seal is in place and connect the 6 pin connector from the completed harness assembly into the rear ofthe potentiometer mounted on the control head mechanism The connector should be fully seated and latched for proper operation User Manual MV3 E Hybrid Controls Page 9 Installation MV3 E Throttle Wiring Connections xx LENGTH 538 F Yellow i PPS2RTN p NE vung Blue PPS 2 C gz Qu Orange i PPS 2 REF SE im TO MV3 E te D Black PPS 1 REF B x x gt TO ENGINE BOAT CONTROL 8 C G i99 O pL Green I LPPS1RIN TOT TAC MODULE was Red PPS 1 uz a x a 6 im A TRAE i 8 T Seal all unused SHIELD cavities to maintain x watertight connection TAC MODULE CONNECTOR BODY BOAT CONTROL CONNECTOR BODY DESCRIPTION DELPHI PACKARD P N Cable seal included 10 POSITION HOUSING 12065425 CABLE O D mm TERMINAL POSITION 12124264 ASSURANCE TPA 2 66 2 00 2 15 1 65 TAC MODULE FEMALE TERMINALS 1 85 1 47 CABLE RANGE mm2 DELPHI PACKARD P N 1 0 0 80 12048074 BOAT CONTROL FEMALE TERMINALS 0 50 0 35 12084200 CABLE RANGE mm2 D
12. ual MV3 E Hybrid Controls Operation MV3 E Side Mount Control Neutral Interlock Ring 7 7 7 7 7 JJ To prevent bumping the MV3 E side mount control out ofneutral a Neutral Interlock Ring has been installed as a preventative safety feature Operation When the Control Hand Lever is in Neutral lift the Neutral Interlock Ring and move the lever forward or reverse to engage the gears Neutral Throttle Warm up Button This feature provides a Throttle Only option to operate the engine throttle without going into gear Operation e When the Control Hand Lever is in Neutral lift the Neutral Interlock Ring and pull out the Neutral Throttle Warm up button at the same time e While holding the ring and button releases move the lever forward to throttle up the engine e When the handle is returned to the Neutral position the releases will reset automatically e Once the releases reset the Control Hand Lever will work both shift and throttle functions User Manual MV3 E Hybrid Controls Page 5 Installation Location of Control Choose a mounting location for the control head which will provide comfortable operation of the hand lever unobstructed movement of mechanism arms and a clear path for cables to engine 1 Allow adequate clearance for hand and lever swing forward and reverse positions See page 13 for the control dimension
Download Pdf Manuals
Related Search