- Yoyomotion
Contents
1. Response MMS message containing the images is sent to 46702222222 Example2 30 user emailaddress com Response2 E mail containing the images is sent to user emailaddress com Note The image size is the size set by the Image Size setting default 320 x 240 Note Quantity can be 1 8 for image sizes 160 x 120 and 320 x 240 Quantity must be 1 2 for image size 640 x 480 See mage settings for more information about the image format Request YOYOCam to automatically send images according to a schedule YOYOCam can be set to automatically send images according to a pre set schedule You can set e upto three active periods per day e adifferent schedule for each day for example workdays and weekends To set the time periods and intervals Command 17 6 Day StartTime1 EndTime1 IntervalTime1 StartTime2 EndTime2 IntervalTime2 StartTime3 EndTime3 iIntervalTime3s Example 116 8 0000 0800 60 1 700 2359 60 Response Periodic sending of images parameter is 8HOOOO O800 60 1 700 2359 60 Note Time is expressed as HHMM for example 0000 is midnight 1200 is mid day 1730 is 17 50 5 30pm 2359 is 23 59 11 59PM Note IntervalTime is in the range 10 to 480 minutes Note The image size is the size set by the mage Size setting default 320 x 240 Day s of the week 17 0 Everyday 6 Saturday 8 Monday to Friday To enable disable periodic image sending Turn On 115 1 Response Periodic sending of imag2. Infrared body detector and camera based Infrared LEDs enable the camera to capture movement detection images in the dark Alarm by SMS Images 12 00 12 30 13 00 Receive images at pre set intervals according toa Simple configuration via SMS commands schedule request images by SMS Remote control arms and disarms YOYOCam and Link up to 15 wireless detectors for example has programmable Emergency button window door smoke Get to know your YOYOCam YOYOCam unit Infrared body Power detector switch Status indicator Infrared LED lights Microphone Mount screw Power inlet socket oo O oo oo ooo oo ooo Battery compartment cover Mount screw Status Indicator x searching for network SIM PIN enabled k Armed se aT Alarm triggered Disarmed Waiting for Master number a Cd o No SIM card System error Se Sending messages Ongoing voice call iz 1s Loading wireless remote sensor O Factory reset Loading sensor Key Sef Fast flash two flashes per second gt lt Slow flash one flash per second Two second flash Remote Control Cover slides open amp closed Arm YOYOCam Disarm YOYOCam Indicator LED lights when any button pressed to indicate transmission Emergency button When the Emergency button My is pressed YOYOCam calls the Master and any added Emergency numbers up to three times in sequence until th
3. operation you cannot be heard 1 Dial YOYOCam s number voice call 2 Call rings at YOYOCam for approximately 10 seconds 3 YOYOCam answers and audio from YOYOCam can be heard 4 Hang up the call to end listening Note Only one person can dial in and listen at once Note YOYOCam cannot send SMS or MMS while a call is connected Request Images from YOYOCam Master Users and Guests can request images from YOYOCam at any time YOYOCam can also be 15 set to automatically send images according to a timetable Request one image To request a single image to be sent to your mobile by MMS Command 03 Response MMS message containing the image Note The image size is the size set by the Image Size setting default 320 x 240 See mage settings for more information about the image format Request a sequence of images You can request YOYOCam to take up to 8 images in a sequence The interval between the images is determined by the Image Interval setting default 0 5 seconds The images are sent to the requesting Master or User by MMS To request a sequence of images Command 03 Quantity Response MMS message containing the images Note The image size is the size set by the Image Size setting default 320 x 240 Note Quantity can be 1 8 for image sizes 160 x 120 and 320 x 240 Quantity must be 1 2 for image size 640 x 480 See mage settings for more information about the image format Request a sequence o
4. pixels The images are taken at the interval selected via the Image Interval command Default interval is 0 5 seconds Command 33 Quantity Example 33H 2 Response Number of Alarm images has been set to 2 The Quantity of images you may include in the MMS depends upon the selected Image Size _ Size Minimum Quantity Default Quantity Maximum Quantity 2 5 J 2 eee 8 C 2 ee 8 24 Image Interval This is the time delay between camera snapshots sent in an MMS The default is 0 5 seconds Command 103 Imagelntervalf Example 103 10 Response mage capture interval has been set to 10 Image Interval may take values 3 to 10 Imagelnterval Value in Milliseconds 800 D 6 06 BB 800 0 900 1000 Image Brightness YOYOCam supports five brightness levels to adjust the camera to the ambient light level Brightness level 1 is darkest and 5 is lightest Default is 4 Command 34 BrightnessLevel Example HB4H 3H Response Brightness has been set to 3 Note Check your image brightness setting in each different condition e g daylight night to make sure that the image is captured ok Image Contrast YOYOCam supports five contrast levels to adjust the camera to the ambient conditions Contrast level 1 is softest and 5 is most contrasty Default is 4 Command 38 ContrastLevel Example HSBHSH Response mage contrast has been set to 3 Note Check your image contrast setting in each different con
5. this error is both formats are sent Emergency phone number list is full YOYOCam already has 9 Emergency numbers set up Use Please delete old number s 07 to check and then delete unwanted number s to make space for the new number s Voice Dialling Mode Default option When the Emergency button My is pressed YOYOCam acknowledges with a bleep By default YOYOCam calls the Master and each added Emergency number in turn until someone answers at which point that person can hear the audio from YOYOCam YOYOCam tries each number up to three times in sequence before giving up The call is allowed to ring for approximately 40 seconds before YOYOCam hangs up and rings the next number in the sequence The LED indicator displays w a zet ongoing voice call For example YOYOCam is configured with Master EmergencyNumber1 and EmergencyNumber2 The Emergency button is pressed _Step YOYOCam action What happens next YOYOCam dials Master Call rings 40 seconds at Master s phone 2 YOYOCam dials EmergencyNumber1 Call rings for 40 seconds at No answer EmergencyNumbert1 3 YOYOCam dials EmergencyNumber2 Call rings for 40 seconds at No answer EmergencyNumber2 Call rings 40 seconds at Master s phone 5 YOYOCam dials EmergencyNumbert1 Call rings at EmergencyNumber1 Call is answered inside 40 seconds User hears audio from YOYOCam If YOYOCam is set to call a landline check that hanging up the landline clears the call So
6. 05555555 46 706666666 Emergency phone number added Note Commands always begin and end with the character and a separates each required parameter Note In some cases all parameters must be supplied in others like the one above as many parameters as required can be supplied Telephone Numbers Some commands require telephone numbers parameters for example when adding a User or an Emergency number You can supply numbers in International format recommended or national format 12 For example International format 46702222222 National format 0702222222 Note Do not include spaces or any other character in phone numbers YOYOCam treats a number in International format as different from one in National format For example if you send 06 46702222222 and 06 46702222222 YOYOCam will not recognise that they are both actually the same user and will configure two users one with the number in each format Switch YOYOCam On and Off Switching On YOYOCam To switch on YOYOCam 1 Slide the Power Switch to the UP position The Status Indicator is orange for a few seconds The Status Indicator turns red for approximately 3 seconds 2 3 we 4 The Status Indicator flashes red while YOYOCam searches for the mobile network 5 YOYOCam bleeps when the network has been found 6 The Status Indicator shows if YOYOCam is armed or 7 if disarmed Switching Off YOYOCAM To switch off YOY
7. 320 x 240 pixels You may wish to have fewer images at higher resolution e g 2 images at 640 x 480 pixels 2 images is the maximum at this resolution Command 433 2 Response Number of Alarm images has been set to 2 Command 32 3 Response mage size has been reset to 3 Size 3 640 x 480 pixels For more information see mage settings Configure the sensors which detect an alarm condition By default YOYOCam detects movement using the infrared body sensor Camera movement detection is also available Infrared Body Sensor Turn On 118 1 Default Response Infrared sensor enabled Turn Off 118 0 Response Infrared sensor disabled Camera Motion Detection Turn On 22 1 Response Motion detection enabled Turn Off 22 0 Default Response Motion detection disabled For more information see Sensor Settings 10 Configure how YOYOCam signals alarms By default YOYOCam sends SMS and MMS to the Master when an alarm is triggered You can also send alarms by E mail and voice calling Additionally YOYOCam can be set to bleep when the alarm is triggered For more information see Alarm Settings Change the Password For security you must immediately change the Password from the default of 1234 to your own value Command 04 0ldPassword NewPassword Example 04 1234 6789 Response Password was successfully changed to 6789 For more information see Guest Users amp Password Add users
8. 33 the Emergency alarm Emergency Numbers The Master can add up to 9 Emergency Numbers To add an Emergency number Use this command to add numbers one by one Use international recommended or national format Command 106 EmergencyNumber Example 106 46703333333 Response 46703333333 Emergency phone number added To add several Emergency numbers in a single command maximum 9 Command 106 EmergencyNumber1 EmergencyNumber2 EmergencyNumber3 Example 106 46704444444 46705555555 46706666666 Response 46704444444 46705555555 46 706666666 Emergency phone number added To delete an Emergency number Command 107 EmergencyNumber Example 107 46703333333 Response 46703333333 Emergency phone number deleted To delete several Emergency numbers in a single command Command 107 EmergencyNumber1 EmergencyNumber2 EmergencyNumber3 Example 107 46704444444 46705555555 46706666666 Response 46704444444 46705555555 46706666666 Emergency phone number deleted To delete all Emergency numbers Command 107 Response Emergency phone number deleted To find out which Emergency numbers are set Command 07 34 Response MMS message including YOYOCam status and Emergency number s Error Responses Emergency phone number already EmergencyNumber has already been set up exists Note that YOYOCam treats the national and international format of the same number as different and will not issue
9. Add users so that other people can also control YOYOCam request images and dial in to hear audio from YOYOCam Command 06 UserNumber Example 06 46702222222 Response 46702222222 USER phone number has been added For more information see Master Users amp Guests Add Remote Controls Before the supplied Remote Controls work with YOYOCam they must be paired You can also configure how YOYOCam responds when the Emergency button is pressed See Using the Remote Control for more information 11 Interacting with YOYOCam General Command Format Commands and Parameters Master and Users interact with YOYOCam by sending SMS messages that contain specially formatted textual commands YOYOCam typically responds with confirmation text by SMS Where the command is a request for images these are sent by MMS or E mail Generic format of a simple command Command CommandCode Example 01 Response YOYOCam is armed Generic format of a command that needs extra information a parameter Command CommandCode Parameter Response SMS confirmation or images by MMS or E mail Example 06 46702222222 Response 46702222222 USER phone number has been added Note There must never be any space characters in a command Generic format of a command taking multiple parameters Command CommandCode Parameter1 Parameter2 Parameter3 Parameter4 Example 106 46704444444 46705555555 46706666666 Response 46704444444 467
10. IR body detection Up to8m SMS MMS Email Voice calls 300 000 pixels 640 x 480 8m 68 degrees JPEG up to6m built in infrared light 2 units included 433 MHz Up to 15 sensors ASK protocol Up to 15m Input 110V 240V Output DC 5 5V 2A Lithium 800mAh Up to 12 hours by SMS 79X125x43 mm 186 grams Copyright 2010 Yoyomotion AB All rights reserved 44
11. MS responses are in Swedish by TDC Song NO 145 TDCNO TDC Song SE 145 TDCSE default Send 127 1 to switch to Telmore DK 1 45 TELMORE English 1 45 UNIVERSAL Ventelo NO 1 45 VENTELONO 8 Network MMS settings are configured Ventelo SE 145 VENTELOSE automatically for the major YOYOCam confirms your phone as Scandinavian networks If your network operator is in the table to the right you must now send the command indicated in order to configure MMS See Mobile Network settings if you need to manually check or configure MMS 9 Arm YOYOCam e Send an SMS with text 01 to arm YOYOCam e Send an SMS with text 02 to disarm YOYOCam YOYOCam is now operational Default Sensor and Alarm Behaviour When armed YOYOCam will raise the alarm when a sensor is triggered By default the built in infrared body sensor is enabled and camera movement detection is disabled See Sensor Settings for more information When a sensor triggers the alarm YOYOCam sends an SMS to the Master followed by an MMS with images Other options include voice call and E Mail alarms Detector image and alarm settings can be configured For more information see Alarm Settings STEP 4 Refine YOYOCam Settings Here are some of the settings that you may like to change in order to configure YOYOCam to your needs Optimize image settings By default YOYOCam takes five images at an interval of 0 5 seconds between each shot The image size is
12. OCam e Slide the Power Switch to the DOWN position Battery and External Power Notifications YOYOCam warns you by SMS when external power is connected and disconnected External power applied External power resumed External power removed External power lost Running on battery For more information see SMS Notification when power supply changes Arm and Disarm YOYOCam When YOYOCam is armed it will raise the alarm when a sensor is triggered When YOYOCam is disarmed it will not raise any alarms YOYOCam is typically disarmed when the property is attended for example during working hours when normal movements would cause only false alarms YOYOCam is armed when the property is unattended for example outside office hours YOYOCam can be manually armed or disarmed Alternatively YOYOCam can automatically arm and disarm itself according to a schedule 13 Arming and Disarming YOYOCam by SMS To arm YOYOCam by SMS Command 01 Response YOYOCam is armed Status Indicator To disarm YOYOCam by SMS Command 02 Response YOYOCam is disarmed w Status Indicator ees Arming and Disarming YOYOCam using the Remote Control Note The Remote Control must first be paired with YOYOCam See Pairing your YOYOCam with a Remote Control for more information To arm YOYOCam using the Remote Control 1 Press the E button on the Remote Control 2 YOYOCam bleeps 3 Status Indicator shows To disarm YOYOCa
13. Please read the description and perform the test as described for emergency numbers Precedence Where multiple alarm options are enabled the precedence is SMS first MMS Email Voice Call last To check Alarm settings Command 07 Response An MMS containing the status of these settings Image settings Image settings allow you to set up the built in camera and optimise picture quality 23 Image Size This setting defines the size of images taken by the built in camera Command 32 Size Example HILHIH Response mage size has been reset to 3 You can chose from three image sizes Default is Size 2 Width x Height Image Image size Application Pixels Quantity Transmit Default Max time 25 sec phone not recommended QVGA 50 sec VGA 75 sec best resolution 1 If you select size 3 image quantity is automatically changed to 2 2 Image size and Transmit time are approximate 3 MMS Transmit time is calculated as approximately 1 11 x Image Size x Image Quantity assuming default Quantity 4 Additional time is taken for the MMS to be transmitted through the mobile network and downloaded to the destination mobile phone 5 This setting sets the size of image that YOYOCam sends in response to the 03 Capture Image s command Image Quantity This setting defines how many images are included in the MMS message that YOYOCam sends upon alarm YOYOCam defaults to 5 images at size 2 320 x 240
14. User Guide YOYOCam G2 GSM Remote Surveillance Camera YOYOMOTION Important Information Please read this information before using your YOYOCam General YOYOCam G2 is a GSM 2G product Make sure your SIM card and subscription support services over 2G for SMS MMS and voice calls All GSM based functions such as calls and SMS messaging are dependent on network performance and availability While YOYOCam G2 is on a voice call Alarm call Emergency call dial in to listen call it is unable to send SMS or MMS messages Test any Voice Call Alarm and Emergency Alarm calls to landlines to make sure that YOYOCam does not block the landline user from making further calls This is a property of the landline telephone network from some providers Photography in public places may be subject to restrictions make sure YOYOCam is operated according to all applicable laws Safety and Usage Guidelines YOYOCam must be used according to the instructions in this User Guide When inserting or removing the SIM card do not touch the gold connectors Use only the approved YOYOMotion AC power adaptor The AC Power adaptor is for indoor use only and must not be used in damp conditions Treat your YOYOCam carefully store it safely and do not drop or throw it or otherwise subject it to shock Do not expose your YOYOCam to dust liquid moisture or humidity Do not use or store your YOYOCam at extreme high or low temperatures Do n
15. a sequence of images Command 03 Password Quantity Response MMS message containing the images Note The format of the image is controlled by the Master Note Quantity can be 1 8 for image sizes 160 x 120 and 320 x 240 Quantity must be 1 2 for image size 640 x 480 Request a sequence of images send to any required mobile phone or E mail address Master and users can request images to be sent to any mobile phone by providing the mobile phone number or to any E mail address You can request YOYOCam to take up to 8 images in a sequence The interval between the images is determined by the Image Interval setting default 0 5 seconds The images are sent by MMS if a mobile number is provided or E mail using the mobile operator s MMS service to send to the E mail address if an E mail address is provided To request a sequence of images to another mobile number or E Mail Command 30 Password NumberOrEmail Quantity Example1 30 1234 46702222222 2 Response1 MMS message containing the images is sent to 46702222222 Example2 30 Password user emailaddress com Response2 E mail containing the images is sent to user emailaddress com Note The format of the image is controlled by the Master Note Quantity can be 1 8 for image sizes 160 x 120 and 320 x 240 Quantity must be 1 2 for image size 640 x 480 38 Factory Reset If the Master phone is lost or you want to set up YOYOCam again from the beginning you can use Facto
16. ait approximately 60 seconds for the mode to time out Error Responses Sensor list is full Please delete old YOYOCam already has 15 sensors added sensor first Delete one first to create a space to add the new one YOYOCam bleeps repeatedly Sensor is already added Indicator light flashes red green for Sensor has not been detected approximately 60 seconds Check that you correctly activated the sensor Checking wireless sensors To check which wireless sensors are present Command 07 Response MMS message including sensor list Deleting Wireless Sensors To delete a wireless sensor Command 112 SensorDescription Example 112 FrontDoor Response Sensor deleted successfully FrontDoor 26 To delete several wireless sensors in one command Command 112 SensorDescription1 SensorDescription2 SensorDescription3 Example 112 FrontDoor BackDoor SmokeAlarm Response Sensor deleted successfully FrontDoor BackDoor SmokeAlarm To Delete all sensors Command 112 Response Sensor deleted successfully Advanced Settings Status Indicator on off You can disable the status indicator if you want YOYOCam to have no visual status indication Turn On 143 1 Default Response Status LED OFF Turn Off 143 0 Response Status LED ON SMS Notification when power supply changes YOYOCam can notify you when the power supply switches between external power adaptor and internal battery To switch SMS po
17. arm enabled Motion detection disabled Infrared lights on Notification by e mail upon motion detection alarm disabled Voice call to preset number upon emergency alarm enabled Voice call to preset number upon alarm enabled 28 Alarm image quantity 5 Image size 320 240 Image direction 0 Image contrast 4 Image interval 5 Image brightness 4 Image compression 1 sensitivity of motion detection 4 Periodic sending of images disabled Day Monday Friday Time 0000 0800 Image capture interval 60 1700 2358 Image capture interval 60 Periodic arming and disarming enabled Parameters are Day daily Time 0800 1700 Warning signal enabled Infrared sensor enabled MASTER phone number 46701111111 USER phone number 46 702222222 46703333333 Sensor Emergency phone number 46701111111 4670555555 Get help with commands You can get a reminder of YOYOCam s commands by sending 09 To get a command list 29 Command 09 Response 00 Set as Master 01 Arm YOYOCam 02 Disarm YOYOCam 03 Password Quantity Request images 04 O0ldPassword NewPassword Change 4 digit password 05 SensorDescription Load sensor 06 number Add USER phone number 07 Report Status 08 Password Reset to default settings 22 0 Disable motion detection 22 1 Enable motion detection Mobile Network settings YOYOCam uses MMS Multimedia Messaging Service to send images and Email mes
18. call Note YOYOCam cannot send MMS images while a voice call is in progress To set Voice Dialling mode Command 39 0 Response Voice call to preset number upon emergency alarm enabled SMS MMS Mode When the Emergency button N is pressed YOYOCam acknowledges with a bleep and sends an SMS alert followed by an MMS with an image to the Master and each added Emergency number SMS Alert Alarm from remote control received To set SMS MMS mode Command 39 1 Response SMS and MMS notification upon emergency alarm enabled 36 Remote Control Battery The remote control uses one CR2032 type 3 Volt battery When the battery runs low YOYOCam bleeps and a warning SMS is sent to the Master 37 Guest Commands This page describes the command s that are available to Guests The Master does not need to add Guest users to YOYOCam Instead the Master gives the Guest the Password and the Password has to be included in the commands that the Guest sends to YOYOCam Request one image To request a single image to be sent to your mobile by MMS Command 03 Password Response MMS message containing the image Note The format of the image is controlled by the Master Request a sequence of images You can request YOYOCam to take up to 8 images in a sequence The interval between the images is determined by the Image Interval setting default 0 5 seconds The images are sent to the requesting Master or User by MMS To request
19. dition e g daylight night to make sure that the image is captured ok Wireless Sensors You can add up to 15 external wireless sensors which operate on the 433MHZ standard When YOYOCam is armed and a sensor is triggered YOYOCam will emit a warning bleep and raise an 29 alarm by SMS only or SMS followed by MMS according to the way the sensor is configured Adding Wireless Sensors To add a Wireless Sensor 1 Make sure the wireless sensor is powered on 2 Send the command to add the sensor to YOYOCam Command 05 SensorDescription SMS notification upon alarm Command 05 SensorDescription SMS and MMS notification upon alarm Example 05 FrontDoor Note SensorDescription is a textual name up to 15 numbers and letters that you choose to identify the sensor If no name is supplied YOYOCam names the sensors 1 2 3 YOYOCam emits a bleep tone and the indicator flashes alternate red and green YOYOCam sends a notification SMS YOYOCam is ready to connect a sensor Please activate the sensor now 5 Activate the sensor For example open the door if you are adding a door sensor Note You have approximately 60 seconds to activate the sensor before YOYOCam cancels the add operation and reverts to normal state 6 When YOYOCam receives the sensor activation signal it will emit a bleep and sent a notification message by SMS SensorDescription has been successfully loaded 7 To exit sensor addition mode press the SET key or w
20. e call is answered at which point the audio from YOYOCam is heard SMS MMS mode can be used as an alternative When the Emergency button is pressed YOYOCam acknowledges with a bleep and sends an SMS alert followed by an MMS with an image to the Master and each added Emergency number See Emergency Button for further information Note The remote control needs to be paired with YOYOCam before use see Pairing your YOYOCam with a Remote Control Getting started STEP 1 Prepare YOYOCam G2 1 Slide the battery compartment cover downwards 2 Lift the battery cover away from the device 6 6 a N 3 Hold the SIM card in line with the slot gold contacts on the underside and slide it in to position e WARNING Always be sure to switch off YOYOCam and disconnect the power before inserting or removing the SIM card e WARNING Do not touch the gold contacts of the SIM Card e Note The SIM PIN must be disabled Use an ordinary mobile phone to check and if necessary turn off SIM Lock 4 Replace the battery compartment cover STEP 2 Mount YOYOCam G2 A mounting bracket is included with YOYOCam To mount YOYOCam 1 2 3 4 5 Locking screw Fixing hole Mount the bracket on the wall ceiling or other surface as required Attach YOYOCam to the threaded tip of the bracket Screw the round lock nut towards YOYOCam to secure YOYOCam on the mo
21. er s mobile phone you can send the 07 Check Status amp Settings command to get the Master number If you have lost the Master number you must perform a Factory Reset and reconfigure YOYOCam from the beginning To change Master number Command 14 NewMasterNumber Example 14 46702222222 Response New MASTER phone number is 46702222222 Note response is sent to the old master number No response is sent to the new Master number WARNING Be very careful to send the correct NewMasterNumber If you get it wrong you must either send this command from the number you entered in error or perform a Factory Reset and reconfigure YOYOCam from the beginning User The Master can add up to 10 users To add a user Command 06 UserNumber Example O6 46 7022222228 Response 46702222222 USER phone number has been added Error Responses UserNumber USER phone UserNumber has already been set up number already exists Note that YOYOCam treats the national and international format of the same number as different and will not issue this error if both formats are sent USER phone number list is YOYOCam already has 10 User numbers set up Use 07 to check full Please delete old and then delete unwanted number s to make space for the new numbers first number s To add several users in one command Command 06 UserNumber1 UserNumber2 UserNumber3 UserNumber4 Example 06 46702222222 46703333333 46704444444 Re
22. es enabled Turn Off 115 0 Default Response Periodic sending of images disabled YOYOCam Settings Master Users amp Guests YOYOCam has three levels of user e Master has complete control over YOYOCam receives alarms amp notifications and can request images e User has some control over YOYOCam and can request images e Guest can request images using the Password supplied by the Master Master The Master has complete control over YOYOCam and can use any command The Master sets up Users and configures YOYOCam as required There is one Master If necessary someone else can be the initial Master and perform the configuration then use the Change Master Number command to hand YOYOCam to the person who will be Master YOYOCam leaves the factory with no Master user defined Performing a Factory Reset operation also clears the Master user and it must be set again as if for the first time To set Master user for the first time From your mobile phone either 1 Send an SMS with text 00 to YOYOCam 2 YOYOCam confirms your phone as Master by SMS V lkommen till YOYOCam L sen ar 1234 Welcome to YOYOCam The default password is 1234 You are now the Master and have full control over YOYOCam 18 Error Responses MASTER phone number YOYOCam already has a Master number configured already exists Note YOYOCam gives this response if you send 00 from the configured Master phone From the Master s or a Us
23. f images send to E mail address You can request YOYOCam to take up to 8 images in a sequence The interval between the images is determined by the Image Interval setting default 0 5 seconds The images are sent to the requesting Master or User by E Mail To request a sequence of images to my E mail address Command 03 Quantity 1 Response SMS message Sending to me myemail com with Quantity pictures E mail message containing the images Note The image size is the size set by the Image Size setting default 320 x 240 Note Quantity can be 1 8 for image sizes 160 x 120 and 320 x 240 Quantity must be 1 2 for image size 640 x 480 Note User s E mail address must have been configured See mage settings for more information about the image format Request a sequence of images send to any required mobile phone or E mail 16 address Master and users can request images to be sent to any mobile phone by providing the mobile phone number or to any E mail address You can request YOYOCam to take up to 8 images in a sequence The interval between the images is determined by the Image Interval setting default 0 5 seconds The images are sent by MMS if a mobile number is provided or E mail using the mobile operator s MMS service to send to the E mail address if an E mail address is provided To request a sequence of images to another mobile number or E Mail Command 30 NumberOrEmail Quantity Examplel 30 46702222222 2
24. f images configured in the image settings default 5 images of 320 x 240 pixels Turn On 110 1 Response E mail notification upon Alarm enabled Turn Off 110 0 Default Response E mail notification upon Alarm disabled Note if both Email and MMS are enabled the MMS message is sent first then the Email 22 See mage settings for more information about the image format To add or change the Email address Master and Each user can add their Email address by sending this command from their mobile phone Command 108 EmailAddress Example 108 night warden yoyomotion com Response Current alarm notification Email address is night warden yoyomotion com To delete all E mail addresses Command 109 Response E mail address deleted Voice Call YOYOCam calls the Master and each added User number in turn until someone answers at which point that person can hear the audio from YOYOCam YOYOCam tries each number up to three times in sequence before giving up The call is allowed to ring for approximately 40 seconds before YOYOCam hangs up and rings the next number in the sequence The LED indicator displays 70 Ongoing voice call Turn On 13 1 Response Call MASTER upon Alarm enabled Turn Off 13 0 Default Response Call MASTER upon Alarm disabled WARNING If Master or any User number is a landline YOYOCam could block the landline and prevent it from hanging up the call to dial other calls
25. m using the Remote Control 1 Press the co button on the Remote Control 2 YOYOCam bleeps e 3 Status Indicator shows 5 To receive SMS notification when YOYOCam is armed or disarmed using the Remote Control Turn On 137 1 Response SMS upon status change by remote control enabled Turn Off 137 0 Default Response SMS upon status change by remote control disabled Arming and Disarming YOYOCam by Schedule Day and Time YOYOCam can be set to automatically arm and disarm itself according to a pre set schedule You can set e upto three armed periods per day 14 e _a different schedule for each day for example workdays and weekends To set the armed periods Command 129 Day Armlimet DisarmTimet ArmTime2 DisarmTime2 ArmTime3 Disarm Time3 Example 129 0000 0800 1 700 2359 armed outside working hours 0800 1700 Response Parameter is 0000 0800 1 700 2359 Note Time is expressed as HHMM for example 0000 is midnight 1200 is mid day 1730 is 17 50 5 30pm 2359 is 23 59 11 59PM Every day Monday 6 Saturday _8 Monday to Friday To enable disable Arm Disarm by schedule Turn On 128 1 Response Scheduled arming and disarming activated Turn Off 128 0 Default Response Scheduled arming and disarming deactivated Dial in and listen to audio Master and Users can dial in to YOYOCam and listen to the audio picked up by the built in microphone YOYOCam is silent throughout this
26. me telephone networks do not clear the call when the called end hangs up making it impossible to dial a new call You must make a test call to ensure that the Emergency Number is not blocked by the call from YOYOCam 1 Add the landline as an Emergency number 2 Press the Emergency button 3 Let the call ring at the Master phone but do not answer or allow voicemail to take the call 4 When the call rings at the landline answer and check that you can hear audio from YOYOCam 35 Hang up the call at the landline Wait 10 seconds 7 Pick up the Landline e If you hear dialling tone and can make another call your line is not blocked e Ifyou still hear YOYOCam the incoming call is blocking your landline This is a property of your telephone network 8 Hang up the call again 9 If your line was blocked now wait 3 or 5 minutes to see if the landline network disconnects the call 10 Pick up the Landline e If you hear dialling tone and can make another call your line is now unblocked You should only dial this landline if the user has an alternative means of dialling a call for example using a separate mobile phone e If you still hear YOYOCam the incoming call is still blocking your landline You must not program YOYOCam to dial this line Mobile phone networks normally allow the called party to end the call and are therefore emergency calls to mobile phones should be able to end the call and immediately make a new
27. n you first set uo YOYOCam do not leave it set at the default 1234 Note If you have lost the Password you must perform a Factory Reset and reconfigure YOYOCam from the beginning 20 Sensor Settings You can set up which sensors trigger the alarm when YOYOCam is armed Infrared Body Detector The infrared body detector works by detecting the heat emitted from a body moving in front of it Turn On 118 1 Default Response Infrared sensor enabled Turn Off 118 0 Response Infrared sensor disabled Note When YOYOCam is operating on low battery the infrared body detector is automatically disabled It is not possible to re enable it until the battery has been charged or external power is connected Camera Motion Detection YOYOCam takes images periodically and compares the latest image with the previous one If there is a significant difference YOYOCam assumes something has moved for example a person has walked in front of the camera YOYOCam raises the alarm Turn On HOOK 1 Response Motion detection enabled Turn Off 22 0 Default Response Motion detection disabled Note When YOYOCam is operating on low battery the camera movement detector is automatically disabled It is not possible to re enable it until the battery has been charged or external power is connected Note Be careful to position YOYOCam so that there is no unwanted motion in view for example a tree shaking in the wind
28. of the same number as two different numbers Possible Solution Set up User number in national or international format and re test Set twice in both formats The network is busy No image has been sent Check that MMS settings are correct ERR_IND 4 _0 Wrong parameters Please check and try again YOYOCam did not understand the parameters 40 included with the SMS command For example in command 33 Quantity 33 1 will fail because Quantity must be between 2 and 8 41 Command Summary These tables summarise the most useful YOYOCam commands MASTER There is one Master user who has complete control over YOYOCam Master only commands Text to send 00 14 NewMasterNumber 04 OldPassword NewPassword Add a User o O 06 UserNumber Add a User 113 UserNumber Delete a User 106 EmergencyNumber Add Emergency Number called when emergency button pressed on remote 107 EmergencyNumber Delete Emergency Number 127 LanguageCode Set Language 0 Swedish default 1 English For example Send 04 1234 6789 to change password to 6789 Send 06 0702222222 to add 0702222222 as a user MASTER amp USER Up to 10 Users set up by the Master can access YOYOCam Master and Users can send these commands Set image size 1 160x128 2 320x240 default 3 640x480 Set quantity of images to take when triggered 1 8 default 3 note 1 Disable 0 infrared body detection enable 1 default Di
29. ol with YOYOCam ar 1 Press the SET button YOYOCam bleeps and LED flashes orange 70 indicating pairing mode 2 Press any button on the remote control YOYOCam bleeps and LED turns green 9 for2 e seconds then returns to orange flashing 7 ready to pair another remote control 3 Press SET to exit pairing mode In any case pairing mode times out after 15 seconds Note If the battery in the remote control is low YOYOCam emits three bleeps and exits learning mode Replace the battery in the remote control and try again To un pair all Remote Controls Command 1117 Response All remote controls have been deleted Arming and Disarming YOYOCam Press A to arm YOYOCam The Status indicator shows when armed Press CT to disarm YOYOCam The Status indicator shows LA when disarmed Emergency Button When the Emergency button My is pressed YOYOCam acknowledges with a bleep By default YOYOCam calls the Master number When the Master answers the audio from YOYOCam can be heard If the Master does not answer YOYOCam will call twice more total three attempts before giving up YOYOCam can be configured to call additional numbers called Emergency Numbers Alternatively YOYOCam can be set to send MMS instead of making voice calls Note YOYOCam responds to the Emergency button N in both Armed and Unarmed states If YOYOCam is busy for example sending images the ongoing operation is cancelled in order to action
30. or a cat jumping in to the field of vision Wireless Sensors You can also add external wireless sensors which trigger the alarm Alarm Settings You can tell YOYOCam what to do when the alarm is triggered 21 Warning Bleep from YOYOCam YOYOCam bleeps for approximately 5 seconds when the alarm is triggered Turn On 130 1 Response Warning signal enabled Turn Off 130 0 Default Response Warning signal disabled SMS Message YOYOCam sends the Master an SMS when the alarm is triggered for example Alarm from IR sensor received Image quantity is 5 Turn On 11 1 Default Response SMS notification upon Alarm enabled Turn Off 11 0 Response SMS notification upon Alarm disabled MMS Message YOYOCam sends the Master an MMS including the number and size of image configured in the image settings default 5 images of 320 x 240 pixels The MMS includes text with a timestamp and the sensor which triggered the alarm for example YOYOCam 203849 Infrared In this example the timestamp is 20 38 49 8 38pm and 49 seconds and the trigger sensor is the infrared movement detector Turn On 124 1 Default Response MMS notification upon Alarm enabled Turn Off 12 0 Response MMS notification upon Alarm disabled See mage settings for more information about the image format Email Message YOYOCam sends an Email to the configured Email address including as attachments the number and size o
31. ot expose your YOYOCam to naked flames lit tobacco products or other heat sources Do not use your YOYOCam in hospitals or near medical equipment If you have personal medical devices such as a pacemaker consult your physician and the manufacturer for advice Do not use your YOYOCam in aircraft or in any place where use of radio transmitters is prohibited Do not use your YOYOCam in places where a potentially explosive atmosphere is present Do not use YOYOCam in proximity to car airbags Do not attempt to take your YOYOCam apart there are no user serviceable components inside the product Do not allow children to play with your YOYOCam small parts such as SIM cards could be detached and represent a choking hazard For optimum performance do not cover your YOYOCam position it with good access to the mobile signal GSM calls and GSM messages Emergency calls calls and messages via the GSM network cannot be guaranteed in all circumstances There is no guarantee that calls can be connected or messages can be sent in all areas or in all mobile networks as the functionality of the GSM based functions are dependent on network performance and availability You should not rely on any voice call capability that your YOYOCam provides for emergency or essential communications Battery Battery performance device runtime depends on signal strength temperature usage pattern and other factors The battery may have temporarily reduced ca
32. ou need to find out the settings for your mobile operator They are often published in the support or help section of the operator s website YOYOCam requires two settings e MMS Center also known as MMS Homepage Message Server e MMS Internet Access Point and WAP Gateway Both must be configured in order for MMS to work YOYOCam automatically selects between WAP or HTTP configuration To configure MMS Center MMSC setting manually Command 124 MMScenter 31 Example 1 24 hitp mmsc t mobile co uk 8002 Response MMS configuration successful http mmsc t mobile co uk 8002 To configure MMS Internet Access Point Settings manually Command 125 GatewaylP WAPGatewayPort HTTPGatewayPort APN APNusername APNpassword Example 125 149 254 201 1354 8080 8002 general t mobile uk user tm Response Set MMS parameter successfully 149 254 201 135 8080 8002 general t mobile uk user tm Reset MMS Configuration To clear out any manual settings and return to automatic MMS configuration Command 54 Response MMS Settings removed New MMS parameter is auto changed to MMSC http mmsc t mobile co uk 8002 IP 149 254 201 135 WAP Port 9201 HTTP Port 8080 APN general t mobile uk APN User user APN Password one2one 32 Using the Remote Control Pairing your YOYOCam with a Remote Control Before use each Remote must be paired with your YOYOCam Up to five remotes can be paired two are supplied To pair a Remote Contr
33. out of credit or there is a temporary network problem Possible Solution Make sure your GSM subscription has sufficient credit Wait for the network to recover or contact your network service provider for assistance Problem YOYOCam rejects my phone call Possible Causes The caller s phone number is not recognised as the Master or a User Possible Solution Check and make sure you are calling from the correct phone number and that your phone is sending the number Calling Line Identification and your phone number is added to YOYOCare Master can check the user list by sending SMS command UL Problem Cannot receive MMS from YOYOCam Possible Causes The MMS service is not activated The MMS profile has incorrect parameters There is a temporary network problem Possible Solution Test the SIM in a regular cell phone to verify the MMS service is activated and that correct MMS settings are used Check the MMS settings in YOYOCare by sending the SMS command 55 MMS messages take normally longer time to deliver compared to SMS messages Problem SIM Card requires a PIN Possible Solution Insert the SIM in to another Mobile Phone and access the Settings to disable the SIM PIN Problem Cannot dial in and listen Possible Cause The number was set up in national format and when the Master or User dials in the mobile network presents the number in International format or vice versa YOYOCam treats national and international format
34. pacity when new or after a prolonged period without use Charge the battery completely when using YOYOCam for the first time Turn of the device and disconnect the power adaptor before removing or inserting the battery Do not allow the battery contacts to touch any metal object The battery should not be exposed to temperatures above 60 C Use only the supplied battery or accessory service replacement battery from YOYOMotion Dispose of any old battery in accordance with the disposal guidelines below WARNING The battery can explode if the product is disposed of in fire Disposal and Recycling Do not dispose of your YOYOCam with normal household waste Dispose of your YOYOCam at an appropriate collection point for electronic equipment For more information contact your local authority your household waste collection depot or the retailer where you bought your YOYOCam About this Guide YOYOMotion AB 2011 Revision 0 5 All trademarks and registered trademarks used in this document are the property of their respective owners Improvements and changes to this text necessitated by typographical errors inaccuracies of current information or improvements to products may be made by YOYOMotion AB at any time and without notice Product specifications are subject to change without prior notice YOYOCam G2 Features Insert a SIM card perform a few simple configuration steps and YOYOCam is ready to guard your property
35. ry Reset to set all settings and parameters back to the factory default Following Factory Reset you will need to re pair the remote controls and any remote sensors re enter any mobile network MMS settings and reconfigure all users etc To perform Factory Reset Reset Key method 1 a 3 Switch Off YOYOCam and wait at least 20 seconds Press and hold the Reset key Switch on YOYOCAM while the Reset key is still pressed After approx 10 seconds YOYOCam bleeps and the indicator LED goes green and ay A4 then flashes red You may now release the Reset key To perform Factory Reset by SMS Master only Command 08 Password Response YOYOCam has been reset to default settings 39 Troubleshooting Problem YOYOCam cannot register a Master Possible Causes YOYOCare has already a registered Master Possible Solution Master Reset your YOYOCare and then register again Problem Master is not recognized Possible Cause The master number was presented to YOYOCam in national format when set up and now the number is being presented in International format or vice versa YOYOCam treats national and international format numbers as different Problem Service Registration fails Possible Causes Temporary network problem Possible Solution Make sure your GSM subscription supports GPRS and that you have the right network specific parameters Problem Cannot receive SMS from YOYOCam Possible Causes Subscription can be
36. sable 0 camera based motion detection default enable 1 39 1 SMS MMS mode when Emergency button is pressed YOYOCam sends SMS and MMS 143 0 or 143 1 Disable 0 indicator LED enable 1 default Master amp Users can also call YOYOCam and listen in via the built in microphone 42 GUEST Guest users are people who do not normally need access but might be asked to check the protected area because they are nearby for example Guest users do not need to be pre defined to YOYOCam but do require the PIN Guest commands Text to send What it does 03 Password Take one image and send it to the requesting guest 03 Password Quantity Take a number Quantity 1 8 of images note 1 30 Password lo Quantity Take a number Quantity 1 8 of images and send to a phone or E mail address To is the mobile number or E Mail address note 1 Note 1 Maximum Quantity is limited to 2 when image size is set to 3 43 Specifications GSM Frequency Bands Working temperature Working Humidity Alarm detection Movement detection distance Alarm modes Camera resolution Camera maximum distance Camera capture angle Picture file format Built in microphone distance Night vision Remote control External wireless 433 MHz sensors Receiving distance sensors Power adapter Built in battery Battery back up Low battery alarm Size Weight 900 1800 MHz 10 to 45 centigrade 10 to 90 Motion detection and
37. sages YOYOCam automatically configures the necessary MMS settings for the major Scandinavian networks If your SIM is issued by some Mobile Virtual Network Operators MVNO then you may need to enter the correct settings Checking MMS Configuration To check presently configured MMS parameters Command 55 Example MMSC http mmsc t mobile co uk 8002 IP 149 254 201 135 WAP Port 8080 HTTP Port 8002 APN general t mobile uk APN User user APN Password tm To check if MMS is configured and working Command 03 Response Request Received YOYOCam images are being sent by MMS YOYOCam s status indicator flashes gt lt while the MMS is sent Images are received MMS is configured The network is busy No image has been sent MMS not configured or wrongly configured 30 Quick Settings for Scandinavian MVNOs YOYOCam has quick settings for the major Scandinavian MVNOs simply send the MVNO name to YOYOCam To enter MMS settings for Scandinavian MVNOs Command 145 Name Example 145 ACN Response ACN MMS settings configured Error Response YOYOCam returns a list of valid names Note Some MVNOs such as TELE2 can be detected from the SIM card and do not require a quick setting because they are automatically configured To view the list of settings for Scandinavian MVNOs Command 145 Response YOYOCam returns a list of valid names Manual MMS Configuration To configure MMS manually y
38. sponse 46702222222 46703333333 46704444444 USER phone number has been added 19 Error Responses as above To find out which User numbers are set Command 07 Response MMS message including YOYOCam status and User number s To delete a user Command 113 UserNumber Example 113 46703333333 Response 46703333333 USER phone number has been deleted To delete several Users in a single command Command 1134 UserNumber1 UserNumber2 UserNumber3 UserNumber4z Example 113 46704444444 46705555555 46706666666 Response 46704444444 46705555555 46706666666 USER phone number has been deleted Guest Users amp Password The Master can invite guests to access YOYOCam Guests can request and view images from YOYOCam The Master does not need to pre define Guests to YOYOCam Instead the Master gives guests YOYOCam s phone number and Password default 1234 Guests have to include the password in the commands they send to YOYOCam To withdraw access from Guests the Master simply changes the Password To change the Guest Password Command 04 0 dPassword NewPassword Example O4 1234 6 89 Response Password was successfully changed to 6789 Error Responses Wrong password OldPassword is incorrect You are not authorized to use this Only the Master can change the password command Password should be a 4 digit number Password must be exactly 4 digits long Note You should change the default password whe
39. unt Loosen the locking screw so that the angle can be adjusted Tighten the screw to fix YOYOCam in the desired position Note There is a second mount position on the underside of YOYOCam The mount screw threads are standard photographic size so YOYOCam can for example be mounted on a camera tripod For best results Avoid pointing YOYOCam at bright lights or windows Position high up so that the camera is angled at least 30 degrees downwards Position in a location where there is adequate GSM signal strength Make test shots e g using command 03 to check image quality Adjust angle and or position of YOYOCam until images are optimal Check that the infrared body detection and or camera movement detection is working STEP 3 Set Up YOYOCam 1 Connect the cable from the power adaptor to the power inlet socket on the back panel as shown e 2 Plug the power adaptor in to a wall outlet or socket strip Slide the power switch to the UP position to turn on YOYOCam 4 After approximately 40 seconds YOYOCam bleeps to indicate that the GSM network has been found From your mobile phone send an SMS with text 00 to YOYOCam Network Operator Command to send Master by SMS V lkommen till H454ACN Chess NO 145 CHESSNO to YOYOCam The default password is Glocalnet 145 GLOCALNET 1234 You are now the Master and Halebop 145 HALEBOP 145 PARLINO have full control over YOYOCam 145 SUPERSTAR 7 The S
40. wer notification on and off Turn On 144 1 Default Response SMS notification upon power source change enabled Turn Off 144 0 Response SMS notification upon power source change disabled Notifications when enabled External power applied External power resumed External power removed External power lost Running on battery Auto Disarm YOYOCam In some circumstances YOYOCam may be repeatedly triggered for example by an employee at work who does not know how to disarm YOYOCam You can configure YOYOCam to stop sending alarm messages after a given number of times by auto disarming 2 To set number of alarms before auto disarm Command 139 Times Example 139 3 Response Disarm the YOYOCam after 3 alarms Note Times must be at least 1 Note After the given number of alarms YOYOCam auto disarms and sends an SMS YOYOCam has auto disarmed Note The counter is reset each time YOYOCam is manually disarmed or armed To enable or disable auto disarm Turn On 138 1 Response Disarm the YOYOCam after several alarms enabled Turn Off 138 0 Default Response Disarm the YOYOCam after several alarms disabled Language English 127 1 Response Language set to English Turn Off 127 0 Default Response Svenska installt Check Settings amp Status View Current Settings To view current settings Command 07 Example Response Disarmed SMS upon alarm disabled MMS upon al
Download Pdf Manuals
Related Search