Home

i i i i i i i i i i i

1. OPERATION MANUAL UNIVERSAL BINARY SENSOR FGBS 321 EN A v1 00 The Universal Binary Sensor is a wireless module that makes it possible to improve the functionality of any sensor with a binary output by allowing it to communicate with the wireless network Z WAVE and the FIBARO building intelligence system Moreover the module allows for wireless communication between the system and the DS18B20 temperature sensors The device can service up to two binary sensors and up to four DS18B20 temperature sensors The Sensor was designed for installation in the housing of a sensor or another device the functionality of which we wish to improve The Universal Binary Sensor may be used whenever wireless collection of data from sensors is required Once additional safety housing have been installed the Sensor can also be used in areas with high humidity and high temperature The Sensor s main function is the integration of the wireless FIBARO system with the existing wire based and wireless alarm and measurement systems As an element of the safety system the device is transparent for parametric alarm lines Technical data Supply voltage 9 30V DC 10 Input 2 potential free inputs 1 digital input 1 wire Output 2 potential free outputs Maximum current carrying 150mA capacity of outputs Maximum voltage at output 36V DC 24V AC 5 contacts Operating temperature 0 40 C Number of servicing 4 temperature sensors Measuremen
2. Default value 200 s Possible parameter settings 0 255s 0 deactivating the function Note Frequent sending of temperature condition reports is reasonable when the sensor is located somewhere where can occure rapid changes of ambient temperature In other cases it is recommended to leave the parameter set to the default value Parameter no 12 Insensitiveness to temperature changes This is the maximum acceptable difference between the last reported temperature and the current temperature taken from the sensor If the temperatures differ by the set value or more then a report with the current temperature value is sent to the device assigned to association group no 3 Intervals between taking readings from sensors are specified by parameter no 10 Default value 8 0 50C Possible parameter settings 0 255 OoC to 160C 0 oF 28 80F In order to set the appropriate value of the parameter the following formula should be used x deltaTx16 for Celsius x delta T x 80 9 for Fahrenheit x parameter value delta T maximum acceptable temperature gradient in Celsius or Fahrenheit If the value is set to 0 then information about the temperature will be sent every time immediately once the readings have been taken from the sensor Parameter no 8 Value of the parameter specifying the forced level of dimming opening sun blinds when comes switch on open command to devices from associat
3. IN1 and IN2 by distinguishing the actions of keys connected to those inputs For example double click would activate the scene goodnight and triple click would activate the scene morning Scene ID is assigned in the following manner input IN1 switch from off to on ID 10 switch from on to off ID 11 remaining IDs are recognized correctly if the value of parameter no 3 was set to 2 holding down ID 12 releasing ID 13 double click ID 14 triple click ID 15 input IN2 switch from off to on ID 20 switch from on to off ID 21 remaining IDs are recognized correctly if the value of parameter no 4 was set to 2 holding down ID 22 releasing ID 23 double click ID 24 triple click ID 25 NOTE Inputs IN1 and IN2 are used to control the condition of the device Each of them may force two conditions for corresponding device channels on alarm off no alarm If monostable keys are used and the value of parameter no 3 or no 4 is set to 2 change of the state of corresponding channel will be able after a single click VI Additional functionality Alarm frame servicing The Fibaro system makes it possible to set the device s reaction to alarm events reaction to the frame SENSOR_ALARM_REPORT The Fibaro Sensor transmits alarm frames of different types depending on the settings in parameters no 5 and 6 The user should correctly declare the type of alarm frame for
4. REGON 301595664 2 The Manufacturer is responsible for equipment malfunction resulting from physical defects manufacturing or material of the Device for 12 months from the date of its purchasing 3 During the Guarantee period the Manufacturer shall remove any defects free of charge by repairing or replacing at the sole discretion of the Manufacturer any defective components of the Device with new or regenerated components that are free of defects When the repair impossible the Manufacturer reserves the right to replace the device with a new or regenerated one which shall be free of any defects and its condition shall not be worse than the original device owned by the Customer 4 In special cases when the device cannot be replaced with the device of the same type e g the device is no longer available in the commercial offer the Manufacturer may replace it with a different device having technical parameters similar to the faulty one Such activity shall be considered as fulfilling the obligations of the Manufacturer The Manufacturer shall not refund money paid for the device 5 The holder of a valid guarantee shall submit a guarantee claim through the guarantee service Remember before you submit a guarantee claim contact our technical support using telephone or e mail More than 50 of operational problems is resolved remotely saving time and money spent to initiating guarantee procedure If remote support is insufficie
5. based systems establish a direct connection between the receiver and the transmitter The radio signal is attenuated by every obstacle along its path in the household e g walls furniture etc In the worst case the radio system ceases to function The advantage of the FIBARO system is the fact that the devices act not only as a signal receiver and transmitter but also as a signal repeater If a direct radio link between the transmitter and the receiver cannot be established the connection will be carried out with the use of other devices participating in communication FIBARO is a bidirectional wireless system This means that the signal is not only sent to the receivers but also the receivers send feedback confirming the reception of the signal This also confirms the condition of receivers which allows us to check whether or not a device has actually been switched on The safety of transmission of the FIBARO system is comparable with a wire linked bus system FIBARO operates in the free band for data transmission The frequency depends on radio regulations in individual country Each FIBARO network has its own unique network identification number home ID which is why it is possible to co operate two or more independent systems in a single building without any interference Although the Z Wave technology is fairly new it has already been accepted as an official standard just like Wi Fi Numerous manufacturers from various f
6. ALARM CO 3 Frame ALARM CO2 4 Frame ALARM HEAT 5 Frame ALARM WATER 255 Control frame BASIC_SET Parameter no 6 Type of transmitted control frame for association group 2 activated via input IN2 The parameter allows to specify the type of alarm frame or to force transmission of control commands BASIC_SET Default value 255 BASIC SET Possible parameter settings 0 Frame ALARM GENERIC 1 Frame ALARM SMOKE 2 Frame ALARM CO 3 Frame ALARM CO2 4 Frame ALARM HEAT 5 Frame ALARM WATER 255 Control frame BASIC_SET Parameter no 7 Value of the parameter specifying the forced level of dimming opening sun blinds when comes switch on open command to devices from association group no 1 In the case of alarm frames the alarm priority is specified Default value 255 Possible parameter settings 1 99 and 255 Value of 255 makes it possible to activate the device when using the Dimmer module it means activating the device and setting it to the previous stored condition e g when Dimmer is set to 30 then deactivated and then reactivated using command 255 it will automatically be set to the previous condition i e 30 Parameter no 11 Interval between forcing to send report concerning the temperature conditions The forced report is sent immediately after the next reading of temperature from the sensor irrespective of the settings of parameter no 12
7. THE DS18B20 SENSOR The DS18B20 sensor may easily be installed wherever very precise temperature measurements are required Moreover if proper protective measures are undertaken the sensor may be used in humid environments or under water it may be embedded in concrete or placed under the floor GLOSSARY OF TERMS e INCLUSION the device sends out a Node Info frame which makes it possible to add it to the Fibaro system Home Center e EXCLUSION removal of device from the Fibaro system e ASSOCIATION controlling other devices of the Fibaro system e MultiChannel Association controlling other multi channel devices of the Fibaro system lll Fibaro Sensor start up 1 Installation of the Universal Binary Sensor Module STEP 1 Connect the device according to the electrical diagram shown in figure 1 Engage the supply voltage Inclusion Exclusion of the Fibaro Sensor to from the Z Wave network STEP 2 The Fibaro Module must be in range of the Home Center 2 controller because the procedure of inclusion to the Fibaro system requires direct communication with the controller STEP 3 Recognition of B button which allows for proper inclusion of device STEP 4 Setting the Home Center 2 controller to the inclusion or exclusion mode see Home Center 2 controller instructions STEP 5 The Fibaro Sensor is added to the network by quickly pressing the B button three times the button is located in the center of
8. ar of the Device and its components listed in the operating manual and in technical documentation as such elements have a defined operational life 16 If a defect is not covered by the guarantee the Manufacturer reserves the right to remove such defect at its sole discretion repairing the damaged or destroyed parts or providing components necessary for repair or replacement 17 This guarantee shall not exclude limit or suspend the Customer rights when the provided product is inconsistent with the purchase agreement This Device may be used with all devices certified with Z Wave certificate and should be compatible with such devices produced by other manufacturers Any device compatible with Z Wave may be added to Fibaro system FIBARGROUP FIBARO In case of any technical questions contact customer service centre in your country www fibargroup com
9. caused by malfunctioning software attack of a computer virus or by failure to update the software as recommen ded by the Manufacturer e damages resulting from surges in the power and or telecommuni cation network improper connection to the grid in a manner inconsistent with the operating manual or from connecting other devices not recommended by the Manufacturer e damages caused by operating or storing the device in extremely adverse conditions i e high humidity dust too low freezing or too high ambient temperature Detailed permissible conditions for operating the Device are defined in the operating manual e damages caused by using accessories not recommended by the Manufacturer e damages caused by faulty electrical installation of the Customer including the use of incorrect fuses e damages caused by Customer s failure to provide maintenance and servicing activities defined in the operating manual e damages resulting from the use of spurious spare parts or accessories improper for given model repairing and introducing alterations by unauthorized persons e defects caused by operating faulty Device or accessories 15 The scope of the guarantee repairs shall not include periodic maintenance and inspections in particular cleaning adjustments operational checks correction of errors or parameter programming and other activities that should be performed by the user Buyer The guarantee shall not cover natural wear and te
10. ce will be reset 3 Controlling the Fibaro Sensor with the Home Center 2 controller The FGBS221 Sensor is a multi channel device This means that it is equipped with two independent input circuits and a 1 wire bus allowing it to be connected to four DS18B20 temperature sensors As a result each device connected to the Sensor is represented by an independent icon in the system After the Fibaro Sensor has been added to the network it shall be represented by appropriate icons in the Home Center 2 controller depending on the number of connected devices 3 7 icons Universal Sensor 4 Fig 1 Fibaro Sensor icon in the Home Center controller In the event of including the Sensor without any sensors connected or with sensors connected only to IN1 and IN2 the device will be represented by three icons If DS18B20 sensors are also connected the devices will be represented by additional temperature icons Note If the number of temperature sensor icons is different than the actual number of sensors connected to the device or if the temperature readings are incorrect you should inspect the connections on the 1 wire bus in particular the connection between respective sensor outputs and the line and the total length of the bus bus bar which should not exceed 30m IV Association Association allows the Fibaro Sensor to directly control another device of the Z wave network e g Dimmer Switch ON OFF Roller Shutte
11. device Default value 20 s Possible parameter settings 1 255 s Note taking temperature readings from the sensor does not result in sending a temperature condition report to the central hub Parameter no 13 Transmitting the alarm or control frame in broadcast mode i e to all devices within range information sent in this mode is not repeated by the mesh network Default value 0 Possible parameter settings 0 IN1 and IN2 Broadcast inactive 1 IN1 broadcast mode active Sensor 2 broadcast mode inactive 2 IN1 broadcast mode inactive Sensor 2 broadcast mode active 3 INI and IN2 broadcast mode active NOTE If the broadcast mode of information transmission is activated for a given channel then transmission of information in singlecast mode to devices assigned to the association group of this channel is deactivated Parameter no 14 Scene activation functionality Default value 0 Possible parameter settings 0 deactivation of functionality 1 activation of functionality The device offers the possibility of sending commands compatible with Command class scene activation Information is sent to devices assigned to association group no 3 Controllers such as Home Center 2 are able to interpret such commands and basing on these commands they activate scenes to which specific scene IDs have been assigned The user may expand the functionality of the button connected to inputs
12. each connected sensor inputs IN1 and IN2 For example for a smoke detector connected to input IN1 the user should declare the frame type 1 ALARM SMOKE value of 1 should be entered to ensure that the remaining devices will correctly recognize information on smoke detector alarm Vil Sensor operation The Fibaro Sensor may be operated with the following operator elements e Any controller compatible with the system e g Home Center 2 controller e Cellular phone e g iPhone or phones of other manufacturers with the proper control application e PC with the use of an Internet browser e Tablet devices e g iPad e With the use of the maintenance button B located inside the housing Vill Procedure to be followed in the case of interference The Device does not react to a programmed transmitter e Make sure that the maximum range was not exceeded and that there are no obstacles along the signal path which contain metal surfaces e g metal cabinets ferroconcrete ceiling and load bearing walls etc e Make sure that the device is not in the programming mode e Possibly repeat the programming process IX GUARANTEE 1 The Guarantee is provided by FIBAR GROUP Sp z o o hereinafter Manufacturer based in Poznan ul Lotnicza 1 60 421 Poznan entered in the register of the National Court Register kept by the District Court in Pozna VIII Economic Department of the National Court Register no 370151 NIP 7811858097
13. from metal elements connection conductors ring brackets etc in order to prevent any interference of the radio signal Metal surfaces in close vicinity e g metal embedded boxes metal door trims may impair the reception capability You should not cut off or shorten the antenna Its length is suited ideally to the band at which the system functions ANT GND TD TP OUT 2 IN2 IN1 GND OUT 1 ev Ee Diagram 1 general NC NC TMP TMP COM 12V ALARM MOTION DETECTOR SYSTEM HUB Diagram 2 connection to a regular alarm line COM AUX COM Z1 ALARM SYSTEM HUB NC NC TMP TMP COM 12V MOTION DETECTOR Diagram 3 connection to a parametric alarm line BELL PUSH PRECIPITATION SENSOR Diagram 5 example connection to a precipitation sensor max30m GND DS18B20 12 3 BOTTOM VIEW GND 9 30V 909 gaa G Ee Diagram 4 connection to DS18B20 sensors Note Do not remove the protective layer surrounding the module Make sure that no metal parts of other devices or conductors come into close contact with the installed Sensor Note Condition of outputs OUT1 and OUT2 is dependent only on the condition of corresponding inputs irrespective of parameter settings or addition of device to the Z wave network Note It should be noted that only the B button starts the device s programming process Include Exclude INSTRUCTIONS FOR ARRANGEMENT OF
14. ields offer solutions based on Z Wave technology which are compatible with one another This makes the system fit for the future and allows for further development For more information go to www fibaro com FIBARO establishes a dynamic network structure From the moment of start up the location data of respective devices of the FIBARO system is updated automatically in real time by confirming their condition in the working mesh network ll Sensor Installation 1 Before the installation make sure to switch off the alarm system or any other system to which the device is to be connected 2 Connect the Fibaro Sensor according to the diagram 3 Place the Fibaro Sensor in the sensor housing 4 Arrange the antenna instructions can be found below the diagrams EXPLANATION OF CONDUCTOR MARKINGS P POWER power supply conductor red GND GROUND ground conductor blue OUT1 output no 1 assigned to input IN1 OUT2 output no 2 assigned to input IN2 TP TEMP_POWER power supply conductor of the DS18B20 temperature sensor brown 3 3V TD TEMP_DATA signal conductor of the DS18B20 temperature sensor white ANT antenna black OUT1 output no 1 assigned to input IN1 OUT2 output no 2 assigned to input IN2 B maintenance button used to add devices to and remove devices from the system ANTENNA ARRANGEMENT INSTRUCTIONS Lay down the antenna as far as possible
15. ion group no 2 In the case of alarm frames the alarm priority is specified Default value 255 Possible parameter settings 1 99 and 255 Value of 255 makes it possible to activate the device when using of the Dimmer module it means activating the device and setting it to the previous stored condition e g when Dimmer is set to 30 then deactivated and then reactivated using command 255 it will automatically be set to the previous condition i e 30 Parameter no 9 Deactivating transmission of the frame cancelling the alarm or the control frame deactivating the device Basic It allows for disabling the deactivation function or the alarm cancellation function for devices associated with the appropriate input of the Fibaro Sensor Default value 0 in the case of association group no 1 and 2 the information is sent Possible parameter settings 0 in the case of association group no 1 and 2 the information is sent 1 in the case of association group no 1 the information is sent In the case of association group no 2 the information is not sent 2 in the case of association group no 1 the information is not sent In the case of association group no 2 the information is sent NOTE Information concerning alarm violation or activation commands for devices from association groups are always sent Parameter no 10 Interval between successive readings of temperature from all sensors connected to the
16. nt the Customer shall fill the guarantee claim form using our website www fibargroup com in order to obtain claim authorization When the guarantee claim form is submitted correctly the Customer shall receive the claim confirmation with an unique number Return Merchandise Authorization RMA 6 The claim may be also submitted by telephone In this case the call is recorded and the Customer shall be informed about it by a consultant before submitting the claim Immediately after submitting the claim the consultant shall provide the Customer with the claim number RMA number 7 When the guarantee claim form is submitted correctly a representative of the Authorised Guarantee Service hereinafter as AGS shall contact the Customer 8 Defects revealed within the guarantee period shall be removed not later than 30 days from the date of delivering the Device to AGS The guarantee period shall be extended by the time in which the Device was kept by AGS 9 The faulty device shall be provided by the Customer with complete standard equipment and documents proving its purchase 10 Parts replaced under the guarantee are the property of the Manufacturer The guarantee for all parts replaced in the guarantee process shall be equal to the guarantee period of the original device The guarantee period of the replaced part shall not be extended 11 Costs of delivering the faulty device shall be borne by the Customer For unjustified se
17. r or scenes scene control is only possible via the Home Center 2 controller NOTE Association allows for direct transmission of control commands between devices and takes place without the participation of the main controller Owing to this mechanism the Sensor may communicate with devices even if the central control hub is completely destroyed e g in the event of a fire The Fibaro Sensor makes it possible to configure three association groups Group is assigned to input IN1 Group II is assigned to input IN2 Group III reports on the condition of the device only one device may be assigned to the group The Fibaro Sensor allows for control over 5 regular devices and 5 multi channel devices per group out of which 1 field is reserved for the network controller In order to add an association with the use of the Home Center 2 controller go to device options by clicking this icon a Select the device options tab Next specify which devices will be associated and with which groups Sending of changed configuration to the device might take couple of seconds V Configuration The Universal Binary Sensor offers a wide range of advanced settings the parameters listed below are available in the Fibaro configuration interface In order to configure the Fibaro Sensor using the Home Center 2 controller go to the device options by clicking on the icon yy Next select the device options tab Device parame
18. rvice calls the Service may charge the Customer with travel expenses and handling costs related to the case 12 AGS shall not accept a complaint claim only when e the Device was misused or the manual was not observed e the Device was provided by the Customer incomplete without accessories or nameplate it was determined that the fault was caused by other reasons than a material or manufacturing defect of the Device e the guarantee document is not valid or there is no proof of purchase 13 The Manufacturer shall not be liable for damages to property caused by defective device The Manufacturer shall not be liable for indirect incidental special consequential or punitive damages or for any damages including inter alia loss of profits savings data loss of benefits claims by third parties and any property damage or personal injuries arising from or related to the use of the Device 14 The guarantee shall not cover e mechanical damages cracks fractures cuts abrasions physical deformations caused by impact falling or dropping the device or other object improper use or not observing the operating manual e damages resulting from external causes e g flood storm fire lightning natural disasters earthquakes war civil disturbance force majeure unforeseen accidents theft water damage liquid leakage battery spill weather conditions sunlight sand moisture high or low temperature air pollution e damages
19. t range 55 C 126 C Radio protocol Z Wave 868 4 MHz for EU 908 4 MHz for US 921 4 MHz for AUS NZ BRA Radio frequency Range up to 30 m in buildings depending on the construction materials up to 50m in the field Dimensions L x W x H 27 3 x 14 5 x 12 mm Technical information e Controlled with FIBARO system devices or any Z Wave controller e Microprocessor based control e Compatible with regular and parametric alarm lines can be connected to 2 alarm detectors e Compatible with binary sensors can be connected to 2 binary outputs e Compatible with DS18B20 temperature sensors can be connected to four DS18B20 temperature sensors e In order to connect the DS18B20 sensors it is recommended to use conductors made from a single wire with a length of up to 30 meters DANGER The Sensor is powered with secure voltage nevertheless the user should be extra careful or should commission the installation to a qualified person Hint The outputs of the device should not be loaded with a current value exceeding 150mA Hint Connections should be made specifically according to the diagrams presented in this manual Incorrect connection may lead to hazards GENERAL INFORMATION ON THE FIBARO SYSTEM FIBARO is a system that does not require any additional conductors it is based on the Z Wave technology FIBARO offers a wide array of advantages in comparison to other similar systems In general radio
20. ters Parameter no 1 Input alarm cancellation delay Additional delay after an alarm from input IN1 has ceased The parameter allows you to specify additional time after which the input no 1 alarm is cancelled once its violation has ceased Default value 0 Possible parameter settings 0 65535 s Parameter 2 byte Parameter no 2 Input Il alarm cancellation delay Additional delay after an alarm from input IN2 has ceased The parameter allows you to specify additional time after which the input no 2 alarm is cancelled once its violation has ceased Default value 0 Possible parameter settings 0 65535 s Parameter 2 byte Parameter no 3 Type of input no 1 Default value 1 INPUT_NC Normal Close Possible parameter settings 0 INPUT_NO Normal Open 1 INPUT_NC Normal Close 2 INPUT_MONOSTABLE 3 INPUT_BISTABLE Parameter no 4 Type of input no 2 Default value 1 INPUT _NC Normal Close Possible parameter settings 0 INPUT_NO Normal Open 1 INPUT_NC Normal Close 2 INPUT_MONOSTABLE 3 INPUT_BISTABLE Parameter no 5 Type of transmitted control frame for association group 1 activated via input IN1 The parameter allows to specify the type of alarm frame or to force transmission of control commands BASIC_SET Default value 255 BASIC SET Possible parameter settings 0 Frame ALARM GENERIC 1 Frame ALARM SMOKE 2 Frame
21. the device STEP 6 Correct inclusion of the device to the network will be signaled by Home Center 2 see Home Center 2 central hub operation instructions Note Do not connect other sensors than DS18B20 to the 1 wire line terminals TP and TD Note Every time when any changes are made to the configuration of TP and TD lines 1 wire e g when DS18B20 sensor s is are included excluded it is necessary to execute the procedure of exclusion and repeated inclusion of the sensor module to the central hub It should be remembered that the system shall enter into the programming mode only once all the connected sensors have been detected about 10 s Note It is prohibited to connect the TP and TD lines to devices that are not compatible with the 1 wire protocol Unused lines should be left insulated 2 Resetting the Fibaro Sensor There are two procedures you can follow in order to reset the Fibaro Sensor Method Resetting in the course of the procedure of excluding the Fibaro Module from an existing Z wave network Devices may be excluded with the use of a controller which offers the option to exclude devices from or include devices to the Z wave network see controller instructions Method II Resetting by cutting off the power supply and re connecting the power supply while holding down the B button after 10 seconds after another cut off and re connection of power supply the settings of the devi

i i i i i i i i i i i

Contents

Download Pdf Manuals

Related Search

Related Contents