User Manual
Contents
1. M 16 17 Failure MOdeS m 20 Powering Up the System o ede een ere irte bete een te eo E e ete i e pb ee ede cen emet 20 Placing the Patient ori the Mattress iie ep te RR PEU ec RR eta tette debi oeste eee latis dedo bg eed 20 6 re nc RT RN UH E ated TAE Ed EHE Ever p De NIRE E Rep t eu deed dte 21 Transferring Patient From To a Wheelchair eese eenn tenn stet ten tentent E ainei PVA O REE EERE EE tentent tentent senten 22 Prep ring for CPR Procedure 5 2 o bea I Ue e et t reete t E EE RA ee Nc ua a Aoc des tec din eret ens 22 About Power Outage and Transportation esee eerte ente ennttnttnntnn tentent tnn ten sten ten teen ten teen ttnt eet ten ttn ten teet ttnen tentent tentent teen ttn teet ten entente 23 5 MAINTENANCE AND TROUBLESHOOTING 24 5 24 secre imc X M Q 27 Part No 1171739 3 Invacare Model CG9900 Mattress GENERAL General 1 1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or prope2. published by the Hospital Bed Safety Workgroup located at www invacare com Use the link located under each bed rail product entry to access this bed safety guide Refer to the owner s manuals for beds and rails for additional product and safety information After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Assist rails with dimensions different from the original equipment supplied or specified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury Fire Hazard Smoking DANGER DO NOT SMOKE while using this device A cigarette can burn a hole in the bed surface and cause damage to the mattress Also patient clothing bed sheets etc may be combustible and cause a fire Failure to observe this warning can result in severe fire property damage and cause physical injury or death Smoking by visitors in the room will contaminate the system Therefore visitor smoking is NOT permitted Part No 1171739 lI Invacare APM Model CG9900 Mattress 3 SAFETY Fire Hazard Anesthesia Equipment DANGER There is an explosion risk if used with flammable anesthetics Fire Hazard Oxygen DANGER There is a possible fire hazard when used with oxygen administering equipment other than nasal mask or half bed tent type The oxygen tent should NOT extend below mattress support level Invacare Model CG9900 Mattress 12 Part No 11
3. Refer to Installing the Power Unit on page 14 Check that air hoses and power cord are clear of moving bed components before placing a patient on the bed Operate all bed frame motorized functions through their full range of motion to be certain that there is no pulling interference or pinching DO NOT strap the mattress to the bed frame at the head and foot ends Secure ALL mattress straps Secure the straps to the bed deck at the head and foot ends and to the frame at the center of the bed Otherwise damage to the mattress will occur when the head and foot ends are raised Refer to Mattress Replacement System on page 13 Invacare Model CG9900 Mattress 10 Part No 1171739 3 SAFETY Entrapment May Occur A DANGER Patient entrapment with bed side rails may cause injury or death Mattress MUST fit bed frame and side rails snugly to prevent patient entrapment Follow the manufacturer s instructions Monitor patient frequently Read and understand the Owner s Operator s Manual prior to using this equipment Invacare product manuals are available at www invacare com or your dealer Proper patient assessment and monitoring and proper maintenance and use of equipment is required to reduce the risk of entrapment Variations in bed rail dimensions and mattress thickness size or density could increase the risk of entrapment Visit the FDA website at http www fda gov to learn about the risks of entrapment Review A Guide to Bed Safety
4. The defective unit or parts must be returned for warranty inspection using the serial number when applicable as identification within thirty days of return authorization date DO NOT return products to our factory without our prior consent C O D shipments will be refused please prepay shipping charges LIMITATIONS AND EXCLUSIONS THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE ENCLOSED INSTRUCTIONS IN ADDITION THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE OR PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL PRODUCTS REPAIRED BY ANYONE OTHER THAN AN INVACARE DEALER SUCH EVALUATION SHALL BE SOLELY DETERMINED BY INVACARE THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CO
5. a green LED on either AP or Static or Max Firm illuminates indicating that the control unit is on If the power comes on after a power outage the control unit will go through its system initialization routine for a few seconds and then resume the desired function Part 1171739 17 Invacare Model CG9900 Mattress 4 OPERATION Firm Soft Buttons Soft Select comfort pressure settings by pressing Firm Soft button Soft Button Pressing this button reduces the pressure setting in the mattress Firm Button Pressing this button increases the pressure setting in the mattress The patient comfort pressure ranges from Soft level 0 8 4 mmHg to Firm level 9 32 4 mmHg The Comfort Control LED displays the patient comfort pressure levels from 0 to 9 and provides a guide to the caregiver to set approximate comfort pressure level depending on the patient weight If the patient s weight to height ratio is above average increase the pressure setting by approximately 2076 or raising the control setting by or 2 above the expected setting for that weight Recommended Pressure Settings For rapid inflation of the mattress activate Max Firm by following the Max Firm instructions 2 For extra firm support during patient ingress egress patient wound care patient turning or patient cleaning it is recommended to set the mattress pressure to Max Firm Max Firm l Activate Max Firm by pressing m
6. 71739 4 OPERATION 4 Operation A CAUTION DO NOT strap the mattress to the bed frame at the head and foot ends Secure ALL mattress straps Secure the straps to the bed deck at the head and foot ends and to the frame at the center of the bed Otherwise damage to the mattress will occur when the head and foot ends are raised 4 Mattress Replacement System The powered mattress comes with eight nylon buckle straps l Remove the original mattress from the bed Head Powered Mattress End 2 If necessary lower the side rails to facilitate installation of the mattress 3 Unroll the powered mattress and place it on the bed frame Buckle Straps Ensure that the hose is towards the foot end of the bed 4 Use the buckle straps to secure the powered mattress to the bed deck in the following locations Head End Head End Bed Deck Foot End Foot End Bed Deck oot En DO End Bed ee FIGURE Mattress Replacement System Mattress Replacement Center Center of the Bed Frame System Hose Part No 1171739 13 Invacare Model CG9900 Mattress 4 OPERATION 4 2 Installing the Side Rails WARNING Patient entrapment with bed side rails may cause injury or death Mattress MUST fit bed frame and side rails snugly to prevent patient entrapment Follow the manufacturer s instructions Monitor patient frequently Read and understand the Owner s Operator s Manual prior to using this equipment Invacare product manuals a
7. Invacare Model CG9900 Mattress User Manual For more information regarding bed rail safety refer to the Bed Rail Entrapment Risk Notification Guide at www invacare com This manual MUST be given to the user of the product Before using this product read this manual and save for future reference Yes you can 2011 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Invacare Model CG9900 Mattress 2 Part No 1171739 CONTENTS GENERAL 4 unb jseex DRE 4 Limited arius M 5 2 OVERVIEW 6 I bIJHHerri e 6 Typical Product Parameters deett Mee edle E Moe imde oit eal sealant aaa 7 3 SAFETY 9 terae KCIIRI II 9 4 OPERATION 13 Mattress Replacement BON M 13 Installing the Side Rails ERROR ec eas esac aaa aad nat 14 Installing the Power Unit 14 Connecting the Ose 15 Connecting th POWER
8. NTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Part No 1171739 5 Invacare Model CG9900 Mattress 2 OVERVIEW 2 Overview 2 Label Location DANGER EXPLOSION HAZARD DO NOT use in the presence of flammable anesthetics A WARNING CAUTION Equipment should be connected to a Patient entrapment with bed side rails may cause injury or death Mattress MUST fit bed frame and properly grounded receptacle 3 prong Risk of side rails snugly to prevent patient entrapment Follow the manufacturer s instructions Monitor Electrical shock DO NOT remove back Disconnect patient frequently Read and understand the Owner s Operators Manual prior to using this equipment Invacare product manuals are available at www invacare com or your dealer Reva air hose before administering CPR Invacare Model CG9900 Mattress 6 Part No 1171739 2 20 Typical Product Parameters Electrical Parameters 2 OVERVIEW CG9900 INPUT VOLTAGE AC 90 V INPUT FREQUENCY 60 Hz CURRENT MAXIMUM POWER CONSUMPTION 5 3W CIRCUIT PROTECTION Dual fused 250 V A fast blow fuses MODE OF OPERATION Performance Paramete
9. d or split manifold Unkink manifold or replace split manifold Has power and fuse is good control unit does not come on Send control unit back to factory for repair Not alternating solenoid malfunction Send control unit back to factory for repair No air pump malfunction Send unit for repair Part No 1171739 Control unit off Check power source and turn on unit Power cord disconnected Connect power cord to the power source No power in the power source Check power source has power and turn it On Power outage Wait till the power source has power Blown fuse 27 Replace blown fuse with an equivalent fuse Invacare Model CG9900 Mattress Part No 1171739 Rev A 2 11 Invacare Corporation USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 www invacare com Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800 668 5324 Yes you can
10. derneath the sacral region of the patient s body Ensure that there is 3 to 4 finger width clearance between the bottom of the patient and the bed frame Adjust the comfort setting if needed Wait five minutes for the mattress pressure to stabilize m Repeat STEPS A E until patient has not bottomed out and patient comfort is achieved 10 If the patient feels that the bed is too soft hard press the Soft or Firm button to adjust the comfort settings 1 Use a regular pillow to help support and stabilize the patient s head 4 9 Transferring Patient From To a Gurney A WARNING ALWAYS engage the wheel locks of the bed and the wheel locks of the gurney before transferring the patient between the bed and the gurney Engage the wheel locks of the bed Refer to the owner s manual provided with the bed 2 Engage the wheel locks of the gurney Refer to the owner s manual provided with the gurney 3 Press the Max Firm or Mode button to achieve maximum mattress pressure Part No 1171739 21 Invacare Model CG9900 Mattress 4 OPERATION 4 Raise or lower the bed to match the gurney height Refer to the owner s manual provided with the bed 5 When the mattress has reached maximum firmness perform one of the following Bed to Gurney Transfer Slide the patient onto the gurney Gurney to Bed Transfer Slide the patient onto the bed 4 10 Transferring Patient From To a Wheelchair WARNING ALWAYS engage
11. detergent solution of quaternary cleaner disinfectant or other germicidal detergent solution B Wipe the mattress components with a clean dry cloth Storing the System Ensure that the control unit is off and disconnect the power cord from the wall outlet Clean the system Refer to Cleaning the System on page 24 Disconnect the air hose connector s from the control unit and allow air to vent from the mattress Gently roll up the mattress with minimal handling and agitation Ensure the cover surface is inside the roll Store the unit keeping the mattress with the control unit Replacing Bladders To replace an individual bladder the buttons for the bladder on both sides Cut a small slit on the red female connector Pull apart the cut female end of the connector and bladder from the male end of the manifold Take the new bladder and dampen the inside of the female end of the connector uk wn Push the new female end of the connector and bladder onto the male end of the manifold securely Invacare Model CG9900 Mattress 26 Part No 1171739 5 2 Troubleshooting PROBLEM Mattress not inflating Not alternating properly 5 MAINTENANCE AND TROUBLESHOOTING Mattress hose disconnected SOLUTION Connect hose connectors and lock them in place Air hose kinked or split Unkink hose or replace split hose Major leak in the air cushions Replace leaking air cushions Kinke
12. dications AN Electrical A WARNING ALWAYS consult the patient s physician before using the CG9900 system DANGER Electrical shock hazard DO NOT remove cover Refer to qualified service personnel WARNING Before performing any maintenance to the power unit disconnect the power cord from the wall outlet DO NOT insert items into any openings of the control unit Doing so may cause fire or electric shock by shorting the internal components The control unit MUST be kept away from all heat sources and radiators during operation Connect the equipment to properly grounded three prong wall outlet using 10 14 ft hospital grade power cord provided with the product Grounding reliability depends upon a properly grounded receptacle 3 prong Part No 1171739 9 Invacare APM Model CG9900 Mattress 3 SAFETY Installation WARNING The CG9900 system is recommended to be installed on medical bed frames with bed side or assist rails It is preferred that the rails be in the raised position whenever a patient is on the bed Health care professionals assigned to each case should make the final determination whether side or assist rails are warranted after assessing patient risks of entrapment and falls in accordance with State patient restraint legislation or facility interpretation of such legislation Controls on the footboard may be obstructed by the power unit on a few bed frames It may be necessary to relocate the power unit
13. e from defects in materials and workmanship for a period of one year from the date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty Invacare warrants the control unit when purchased new and unused to be free from defects in materials and workmanship for a period of one year from the date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty If within such warranty period any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option with refurbished or new parts This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Product repairs shall not extend this warranty coverage for repaired product shall end when this limited warranty terminates Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover Provide dealer s name address model number and the date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Invacare Corporation will issue a return authorization
14. els If soiled the cover should be removed cleaned and decontaminated 8 Perform the following steps to clean the mattress cover A Using a clean sponge or paper towel Scrub the area with freshly prepared effective phenolic detergent disinfectant solution B Remove the cover and launder it using the following method A CAUTION Laundry workers should always wash their hands before working with clean bedding DO NOT overload the machine DO NOT use chlorine bleach because it may damage the fabric coating High air temperatures will damage the fabrics and void the Invacare warranty i Place the cover in a washing machine ii Wash with warm water below 120 iii Add detergent and disinfectant according to the manufacturer s instructions iv Remove excess water v Set the dryer to the lowest setting below 120 vi Dry the cover until it is completely dry 9 Perform the following steps to clean the control unit and hose fittings A Wipe all controls chassis and hose fittings with a quaternary disinfectant solution B Using a nylon brush gently clean all crevices as they can harbor microorganisms C Air dry all treated surfaces Part No 1171739 25 Invacare Model CG9900 Mattress 5 MAINTENANCE AND TROUBLESHOOTING 10 Perform the following steps to clean the mattress components air cushions mattress base etc A Using a clean sponge or paper towel wipe down the mattress components with a dilute
15. hooting 5 1 Cleaning the System A WARNING Before cleaning or disassembling the CG9900 mattress check the underside of the mattress folds for sharp objects such as scissors needles etc These objects should be removed and discarded before proceeding with further cleaning or disassembly otherwise injury or damage to the product may occur Because of potential risk of infectious exposure cleaning with the patient on the bed is not recommended All equipment should be inspected Any item that is visibly soiled with the patient s blood or other body fluids should be properly cleaned or removed Laundry workers should treat all soiled bedding as if it were contaminated with pathogenic microorganisms Remove the bedding If necessary inflate the mattress Ensure that the control unit is off Unplug the power cord from the wall outlet Ensure that the underside of the mattress is clear of all sharp objects Examine the surface of the control unit and mattress assembly components for visible blood or body fluids Ur hec E Perform one of the following fblood is present decontaminate the product i Remove all visible soil with disposable paper towels ii Scrub the area with freshly prepared effective phenolic detergent disinfectant solution Invacare Model CG9900 Mattress 24 Part No 1171739 5 MAINTENANCE AND TROUBLESHOOTING fblood is not present remove any soil from the cover with paper tow
16. ode key Max Firm LED will light up this mode The Max Firm is used to rapidly inflate the mattress Max Firm Mode will deactivate after 44 minutes at which point the LED will curn off and the unit will default to its previous setting In this mode the entire mattress will be pressurized to 35 5 mm Hg It takes 40 60 minutes for the mattress to inflate fully inflation time depends on size of mattress It is recommended that Max Firm setting be used during patient ingress egress patient wound care patient turning or patient cleaning Invacare Model CG9900 Mattress 18 Part No 1171739 4 OPERATION Static To set static mode press the Mode key until the Static LED is lit In static mode all the air cushions in the mattress will be maintained at constant pressure Alternating Pressure To set alternating pressure A P mode press the Mode key until the A P alternating pressure LED is lit 2 n the A P mode the even numbered air cushions in the mattress will deflate while the odd numbered cushions remain at constant pressure When 10 minutes has elapsed the even numbered air cushions will inflate while the odd numbered cushions remain at constant pressure When 10 minutes has elapsed again the odd numbered air cushions deflate while the even numbered cushions remain at constant pressure The air cushions continue to inflate or deflate like this as long as the alternating pressure mode is selected Adjus
17. re available at www invacare com or your dealer Refer to the instructions provided with the side rails for the installation procedure Installing the Power Unit l Swing out the bed hooks on the back of the control unit 2 Place the control unit on the footboard If the bed does not have a footboard place the control unit on a flat surface leaving room for the hose to hang down Invacare Model CG9900 Mattress 14 Bed Hooks FIGURE 2 Installing the Power Unit Part No 1171739 4 OPERATION 43 Connecting the Hose A CAUTION Ensure that the hose connecting the control unit to the mattress is routed such that it cannot be stepped on kinked squeezed or otherwise damaged Locate the hose at the foot end of the mattress Locate the control unit connectors on the right side of the control unit Squeeze and hold the tabs on the hose connectors BABowM gt Push the hose connectors onto the control connectors until an audible click is heard The audible click indicates that the hose connectors are properly engaged with the control connectors Control Unit Connectors Hoses Tab Hose Connector FIGURE 3 Connecting the Hose Part No 1171739 15 Invacare Model CG9900 Mattress 4 OPERATION 4 4 Connecting the Power Cord WARNING DO NOT alter plug to fit a non conforming outlet Instead have an electrician install a properly grounded 3 prong outlet Failure to use
18. rs CG9900 WEIGHT CAPACITY 350 Ibs PRESSURE ZONE 2 MAXIMUM FLOW 12 4LPM MAXIMUM FLOW PRESSURE 35 5 mmHg 45 minutes 20 45 minutes MAXIMUM FLOW TIMER SUPPORT SURFACE INFLATION TIME Part No 1171739 7 Continuous CG9900 PATIENT COMFORT CONTROL PRESSURES SOFT PRESSURE FIRM PRESSURE CYCLE TIME 8 4 mmHg 32 4 mmHg 10 minutes PATIENT CONTACT Control unit and mattress have Latex Free components Invacare APM Model CG9900 Mattress 2 OVERVIEW Mechanical Parameters CONTROL UNIT CG9900 DIMENSIONS 9 x 4 5 x 5 LX W X H WEIGHT 5 Ibs POWER CORD 10 14 Feet Long Hospital Grade CONNECTION Two Flow Couplings PACKAGING piece box AIR FILTER None Environmental Parameters CG9900 OPERATING CONDITIONS AMBIENT TEMPERATURE RELATIVE HUMIDITY ATMOSPHERIC PRESSURE 50 104 F 30 75 Non Condensing 70 106 kPa STORAGE AND SHIPPING CONDITIONS AMBIENT TEMPERATURE RELATIVE HUMIDITY ATMOSPHERIC PRESSURE Invacare Model CG9900 Mattress 40 158 F 10 100 Non Condensing 50 106 kPa Part No 1171739 3 SAFETY 3 Safety 3 1 General Guidelines 1 NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact Invacare Carrier for further instruction Contrain
19. rty damage See the information below for definitions of the signal words DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use Invacare APM Model CG9900 Mattress 4 Part No 1171739 GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the mattress and cover when purchased new and unused to be fre
20. sportation or power failure as long as the mattress is connected to the control unit 47 Powering Up the System For this procedure refer to FIGURE 4 on page 17 Turn on the power to the system by pressing the Power button on the control unit Once the button is released a green LED illuminates when the unit is on 4 8 Placing the Patient on the Mattress l Press the Mode button to select Max Firm Mode In this mode the Max Firm LED lights up 2 After the mattress is fully inflated place the patient on the mattress 3 Ensure that the patient s feet are towards the foot end of the mattress the end with the hose Invacare Model CG9900 Mattress 20 Part No 1171739 4 OPERATION 4 Center the patient on the bed from side to side and head to foot Special positioning may be required with contracted patients to provide comfortable positions After placing the patient make certain no objects will fall under the patient such as feeding tubes IV s etc Wait five minutes for the mattress pressure to stabilize Once the mattress inflates to its normal size set the comfort pressure to the desired comfort level Wait five minutes for the mattress pressure to stabilize 50 09 5 Verify that the patient has not bottomed out by performing the following steps Ensure that the patient is lying flat on his her back in the middle of the mattress Place four fingers between the air cushions directly un
21. the correct plug and outlet can result in a potential safety hazard CAUTION Ensure that the power cord of the control unit is not pinched or has any objects placed on it and also ensure it is not located where it can be stepped on or tripped over Examine the hospital grade power cord supplied with the control unit 2 Perform one of the following Ifthe cord is damaged Call your supplier for a replacement hospital grade cord Ifthe cord is not damaged Plug the end of the supplied hospital grade power cord into the power outlet on the side of the control unit 3 Plug the other end of the plug into a properly grounded outlet on the wall Once the unit is plugged in an amber LED on the control unit is lit indicating that the system is in STAND BY mode Invacare APM Model CG9900 Mattress 16 Part No 1171739 4 OPERATION 4 5 Using the Front Panel Patient Weight Ibs 405 140 175 210 245 280 315 350 Alarm Power Fail LED 70 Fower Fail Low Pressure ow Pressure LED Alternating Static Max Firm Soft Button Standby 49 2 Firm Button Static Alternating See Pressure and Max LCD Displa Power Button ee Firm Button FIGURE 4 Using the Front Panel Power Button l turn the control unit on or off press and release the Power button Once the unit is plugged in an amber LED on the control unit is lit indicating that the system is in stand by mode Once the Power button is pressed and released
22. the wheel locks of the bed and the wheel locks of the wheelchair before transferring the patient between the bed and the wheelchair Engage the wheel locks of the bed Refer to the owner s manual provided with the bed Engage the wheel locks of the wheelchair if applicable Refer to the owner s manual provided with the wheelchair Press the Max Firm or Mode button to achieve maximum mattress pressure Raise or lower the bed to match the wheelchair height Refer to the owner s manual provided with the bed Unc ce codo NM s When the mattress has reached maximum firmness perform one of the following Bedto Wheelchair Transfer Slide the patient onto the wheelchair e Wheelchair to Bed Transfer Slide the patient onto the bed 4 11 Preparing for CPR Procedure For this procedure refer to FIGURE 5 Press and hold the tabs on hose connector while pulling the hose from the control unit Invacare Model CG9900 Mattress 22 Part No 1171739 4 OPERATION Control Unit Connectors Mattress Hose Connector Hoses FIGURE 5 Preparing for CPR Procedure 4 12 About Power Outage and Transportation If the hoses remain connected to the control unit the mattress retains air during a power outage during transportation when the control unit is unplugged or when the control unit is turned Off Part No 1171739 23 Invacare Model CG9900 Mattress 5 MAINTENANCE AND TROUBLESHOOTING 5 Maintenance and Troubles
23. ting the Minimum Pressure Setting A P Low The minimum pressure setting during alternating pressure is set to 0 3mm Hg at the factory This means the mattress will deflate as much as possible during the deflation time when using the A P mode The setting can be changed so the mattress will only deflate to 5076 of the selected pressure setting l Ensure the standby LED is lit 2 Perform the following e Press and hold the Firm and Mode keys while in standby 3 Read the LCD display The LCD display will flash 2 UNIT WILL DISPLAY 0 FOR LOW A P SET TO 0 3 mmHg E UNIT WILL DISPLAY 5 FOR LOW A P SET TO 50 OF High 4 Perform one of the following to toggle between the two settings PRESS MODE KEY TO TOGGLE LOW SIDE A P PRESSURE PRESS ON STANDBY KEY TO END ROUTINE Part No 1171739 19 Invacare Model CG9900 Mattress 4 OPERATION 4 6 Failure Modes Power Fail LED In the event of power outage Power Fail LED flashes AMBER The control unit has internal memory and retains the previous settings during the power outage During a power outage the mattress retains the air as long as the mattress is connected to the control unit Low Pressure LED In the event that the mattress hose disconnects or low pressure is detected an alarm sounds and Low Pressure LED flashes AMBER Once the low pressure problem is fixed the control unit resumes operation in the previously set mode The mattress will hold air during tran
Download Pdf Manuals
Related Search