Home

53 , USER`S MANUAL

1. For 16 1FX 24 2FX ports model STATUS CONDITION Switch is receiving power Link Act Port has established a valid link Flashing Data packets being received or sent The connection speed is 100Mbps Yellow The connection speed is 10Mbps FDX ON The connection is Full Duplex OFF The connection is Half Duplex 6 Manage Configure the switch 6 1 Introduction of the management functions This switch is a L2 management switch It supports in band management function from SNMP Http and Telnet interface It also supports out band management function from RS232 console interface Besides it supports network configuration functions like VLAN Trunking Port Mirror QoS spanning tree and software backup update Users can configuration these functions for different network applications The following is a brief introduction about these functions before the detail operation sections 1 VLAN Virtual LAN VLAN can divide the switch to several broadcast domains to prevent network traffic between different user groups This switch supports 802 1Q tag based VLAN Users with the same VLAN ID can transfer data to each other The network traffic will be blocked if they have different VLAN ID 2 Trunk If two switches are cascaded together the bottleneck will happen at the cascading connection If more cables could be used for the cascading connection it will reduce the bottleneck problem In normal case switches will b
2. txtime sub command is used to set the timeout value for the identification request from the switch to users The request will be re tried until the reauthent is met After that authentication fail message will be sent The valid value is 0 65535 rsip sub command is used to set the IP address of RADIUS server authport sub command is used to set the handshaking port number between the switch and RADIUS server It could be different for different RADIUS servers shkey sub command is used to set the security key between the switch and RADIUS server portauth sub command is used to set the authentication mode for a physical port Its syntaxis set dot1x portauth port auto fa fu no auto the authentication mode of the port depending on the authentication result of the port fa force authenticated will force the port always being authentication successful in 802 1x process and the real authentication result will be ignored fu force unauthenticated will force the port always being authentication unsuccessful in 802 1x process and the real authentication result will be ignored 24 none 802 1x function will not be executed on the port i e disabled on the port Note This switch supports MD5 TLS and PEAP authentication types 9 19 set security command This command is used to set the Mac address security mode of physical port Its syntax is gt set security Syntax set security port mode mode
3. negotiation attribute for the speed duplex mode setting And the Auto MDIX function of the port is still enabled If the connected device is auto negotiation enabled and you want to set the speed of the connection for example 10M Half you can select ad mode If the connected device is in forced mode for example 10M Half and it is auto negotiation disabled you can use an mode and set the port to the same configuration as the device in port configuration function You can select an mode or ad mode depending on your applications In most of the connection cases ad mode is suggested 9 10 set port command This command is used to change the connection configuration of ports Its syntax is gt set port 2 Syntax set port port arg_1 data_1 arg_1 data_1 arg_n data_n Argument List name Set port name string admin Set port admin enable disable speed Set port speed auto 10 100 1000 duplex Set port duplex full half flowctrl Set port flowctrl ON OFF User can configure the following items for each port a Name of a port with name sub command b Enable Disable a port with admin sub command c Operation speed of a port with speed sub command d Duplex mode of a port with duplex sub command 17 e Flow Control function of a port with flowctrl sub command There is also a flow control setting command in QoS function Please r
4. 9 11 4 set qos flowctrl command This command is used to configure flow control function of port when QoS is enabled There is also a flow control enable disable function in port configuration Here is the table about the flow control settings Flow control setting in Flow control setting in Flow control operation QoS when QoS Enable port configuration Enable Enable Enable Enable Disable Disable Disable Enable Disable Disable Disable Disable 18 When flow control function is ON the switch will send pause frame to prevent packet lost when traffic congestion happens If flow control function is OFF the switch will drops packets when traffic congestion happens Note QoS and flow control functions are two conflict operations for a switch For real QoS request flow control function should be OFF to allow packets to come in switch and being forwarded by priority when congestion happens But it depends on user s application For example set qos flowctrl 5 off command will disable flow control operation of Port 5 when QoS is enabled 9 11 5 set qos mapping command This command is used to map the 802 1P priority 0 7 to the four priority queues For example set qos mapping 3 1 command will map the 802 1P tag priority 3 to priority queue P1 and packets with tag priority 3 will be forwarded to priority queue P1 of egress port 9 12 set snmp command This command is used to configure SNMP function o
5. N 27 1 Mb with N 29 127 PortNumber Ingress Rate Control Egvess Rate Control 1 P 0127 NoLimt P Q 127 No Limit 2 D a127 NoLimit P 427 No Limit 3 D 127 1280Kb 127 No Limit 4 H Qnt27 NoLimit P 427 No Limit 5 P u127 NoLimit E 127 40Mb 6 H a127 NoLimit P 127 No Limit 7 P a127 NoLimit P 0 127 No Limit 8 P o2 Ham 0 127 No Limit ai The rate control function can limit the maximum traffic rate for each physical port The traffic could be ingress traffic or egress traffic The rate control range is 64Kbps 100Mbps Here is the rule for the setting Maximum Rate Rate Control Number N Rule No Limit 0 0 means no limit 64K 128K 192K 1792Kbps 1 28 Rate N x 64Kbps 2M 3M 4M 100Mbps 29 127 Rate N 27 x 1Mbps For example if you want to limit the download traffic rate of Port 2 to 512Kbps you should set the Egress Rate Control of Port 2 to 8 8 512 64 and egress is for download operation and ingress is for upload operation The Packet Drop for Ingress Limit is for packet dropping operation when ingress traffic rate exceeds the Ingress Rate Control If it is enabled the extra packets will be dropped to limit the ingress traffic rate If it is disabled flow control function will be used to pause the ingress traffic 54 15 Storm Control Storm Control Control Rate 33 EH Apply Broadcast Control C
6. Please refer to the description of Upgrade function in console operation in Section 6 2 3 From web browser Doing by http protocol and by web browser Please refer to the description of Tools function in Section 6 3 61 A Product Specifications Access Method Standards Conformance Communication Rate MDI MDIX Media Supported Indicator Panel Number of Ports Dimensions Certification Power Consumption Temperature Humidity Bridging Function Switching Method Address Table Filtering Forwarding Rate Maximum Packet Size Flow Control VLAN QoS Spanning Tree Trunking Mirror Port SNMP 8 Ports Model Ethernet CSMA CD IEEE 802 3 10BASE T IEEE 802 3u 100BASE TX 10 100Mbps Full Half duplex auto negotiation Auto detect for each port 10BASE T 100 Ohm Category 3 4 5 twisted pair 100BASE TX 100 Ohm Category 5 twisted pair LEDs for each unit Power each port Link Act 100M FDX 8 RJ45 TX ports 250 x 117 x 37 mm CE Mark FCC Class A 10 Watts max Standard Operating 0 to 50 C 5 to 95 Non condensing Filtering forwarding and learning Store and forward 4K entries Line speed 1536 Bytes Auto detect Enable Disable state 802 3x for full duplex backpressure for half duplex 802 1Q VLAN 4 transmit queues per ports for port based 802 1P tagged based priority operation Support IEEE 802 1D protocol 4 groups max 1 capture port for Ingress Egress traffic DA SA filtering
7. ingressfilter Set ingress filter Enable or Disable Create Create new 802 1Q vlan with specified VLAN ID and VLAN Name modify Modify forward and untagged memeber Dvid Set the Port VLANID of specified port mgrpvid Set the Port VLANID of management port priority Set the priority of specified port block Set the Block of VID mode Set the VLAN Mode enable and disable sub commands are used to enable disable 802 1Q VLAN function of the switch ingressfilter sub command is used to enable disable VLAN filtering executed at ingress port Enable the VLAN filtering function will be executed when packet is received at ingress port If the ingress port is in the same VLAN of the received packet this packet will go to forwarding stage Otherwise the packet will be discarded by VLAN filtering at ingress port Disable the VLAN filtering function will be executed when packet is forwarded to egress port create sub command is used to create a static 802 1Q VLAN For example set 1qvlan create ABC 20 will create a static 802 1Q VLAN with name ABC and ID 20 modify sub command is used to modify a static 802 1Q VLAN setting Its syntax is gt set 1qvlan modify Syntax set 1qvlan modify port VLANID 1 lt tagged gt 0 lt untagged gt Examples Set 1qvlan 1 5 7 2 1 Description Add port 1 5 to VLAN 2 as tagged port and remove port 7 from VLAN 2 pvid sub command is us
8. the tag The untagged port will always send out packets without tag If tagged packet is received from ingress port tag will be removed from the packet before forwarded to untagged port Most the network adapters or devices are untagged devices If they are connected to tagged port they will fail to access network because of the tag in packet About Switch Management from Users Only the users in the same VLAN as Management Port PVID set in 802 1Q VLAN Configuration page can manage the switch via Web Telnet SNMP The users in other VLAN cannot manage the switch from network 46 9 Dynamic 802 1Q VLAN Dynamic 802 19 VLAN Show VLAN Table Ma0 VLAN D VLAN Type VLAN Name 1 STATIC Default VLAN U amp S An Untagged and Static member U amp D An Untagged and Dynamic member T amp S A Tagged and Static member T amp D A Tagged and Dynamic member This table will show the activity of 802 1Q VLAN Select a VLAN in Show VLAN Table The 802 1Q VLAN activity status will be shown for the selected VLAN If GVRP protocol is enabled this table will also show the learned remote 802 1Q VLAN 47 10 802 1x Configuration 802 1x Configuration 802 1 System Authentication Status Disable v Authentication Configuration Re authentication Disable D Re authentication Timeout Period 3600 0 65535 seconds R
9. 0 disable Mac address security operation 1 Accept mode only the user with the static address can access the port 2 Reject mode only the user with the static address cannot access the port For examples set security 1 1 will set Port 1 to accept the users with the static Mac addresses configured on Port 1 Please refer to set arl command for static address setting Or you can set static address from the Dynamic Mac Address Table in web interface The table will show the learned Mac addresses and you just need to select from the learned address list Note Here is an Application Note for Mac address filter in function It needs two conditions for Mac address filter in function working 1 The port security mode is set to Accept 2 Static Mac address is assigned on Port for example Mac 1 on Port 1 In this case only Mac 1 can access network through Port 1 But there is also a limitation for Mac 1 it can access network through Port 1 only because it is a static fixed address on Port 1 9 20 set ratecontrol command This command is used to set the maximum traffic rate to from physical ports of the switch Its syntax is gt set ratecontrol Syntax 1 Set ratecontrol drop 0 1 Examples Set ratecontrol drop 1 Description Set drop packet for ingress limit enable Syntax 2 Set ratecontrol ingress egress port 0 127 Examples Set ratecontrol ingress 1 10 Description Set
10. 0 gateway 192 168 1 154 will set these parameters as the IP address configuration of the switch After the command you can use show net to verify the setting Note After IP configuration is modified the switch will reset itself set idle command This command is used to set idle time for console connection If no any key operation in this idle time the switch logout automatically for security Its syntax is gt set idle Syntax Set idle timeout value For example set idle 300 will change the idle time to 300 seconds It is 10 minutes default Its valid range is 30 3600 seconds set igmp command This command is used to enable disable IGMP snooping function for IP multicast operation Its syntax is gt set igmp Command List enable Enable igmp snooping function disable Disable igmp snooping function set mirror command This command is used to configure mirror port function The following is the sub command for it gt set mirror Command List E Help commande help Help commands ingress Set mirror ingress setting egress Set mirror egress setting port Set mirror capture port setting enable Enable mirror function disable Disable mirror function 15 9 7 1 set mirror and set mirror help command This command can show the sub command list for set mirror command 9 7 2 set mirror ingress command This command is used to con
11. 05148 RP 1708I USER S MANUAL Intelligent Switch User s Manual We make no warranties with respect to this documentation and disclaim any implied warranties of merchantability quality or fitness for any particular purpose The information in this document is subject to change without notice We reserve the right to make revisions to this publication without obligation to notify any person or entity of any such changes Trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies Contents 1 INTRODUCTION tere etekge eet EN Nee eege dh SRNEK Eeer hanain nananana aawa 1 Tal PACKAGE CONTENTS ee AE AE ee 1 2 WHERE TO PLACE THE INTELLIGENT SWITCH c csessseeeeeeeeeeeeeeeeenees 2 3 CONFIGURE NETWORK CONNECTION c cccceceseseeeeeseeeeeeeseeeeeseeeeeeesenseeeees 3 3 1 CONNECTING DEVICES TO THE INTELLIGENT SWITCH n sssssssssesesesesesesesesesesesesesene 3 3 2 CONNECTING TO ANOTHER ETHERNET SWITCH HUB nsssssssosesesesesesesesesesesesesesesene 3 3 3 APPLICATION adeleg tadeweveevebvseadaven adedvievaaavaseveede Gul ousievevdnee EA Eo 3 4 ADDING MODULE EEN 5 4 1 ADDING 100BASEFX MODULE FOR 16 1FX 24 2FX MOpEL 5 5 LEDS CONDITIONS DEFINITION c cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeseseeenens 6 5A LEDS DEFINED saci cosecetcdtes deed ENEE Eeer En 6 6 MANAGE CONFIGURE THE SWITCH ccccccccseseseseeeeeeeeeeeeeeeeeseeeeeeeseeeeeeees 7 6 1 INTRODUCTI
12. 33 is DYNAMIC in port 2 If the Mac address is not in ARL table it will be shown as follow gt find arl 00 c0 f6 77 88 99 Failed 12 Note Dynamic means the Mac address could be dynamic learning and aging by the switch Static means the Mac address is fixed in ARL table 4 Exit command This is a logout command the same as Logout command 5 Help command This is a help command the same as command and the switch will prompt command list for this command 6 Logout command This is a logout command the same as Exit command 7 Ping command User can use this command to ping another network device to verify the network connection and activity It is similar to the ping command in MS DOS Enter ping at the prompt the command syntax will be shown gt ping Syntax ping n count H length LO w timeout ip n count Number of echo requests to send length Send buffer size and length is between 64 8148 t Ping the specified host until stopped by lt ESC gt key W Timeout in milliseconds to wait for each reply ip IP address XXX XXX XXX XXX For example ping 192 168 1 80 Ctrl C can be used to break continuous ping operation 8 Reset command The command can be used to reset switch or restore factory default setting Enter reset at the prompt the command syntax will be shown gt reset Syntax reset configuration system reset configurat
13. 7 r a ors r D Down B Enable M a Hal D Apply Users can find the link status Link It shows the link status of each port Disable You can disable a port here Auto You can enable disable the auto mode of ports here If auto is disabled the Speed and Duplex setting will become active The auto mode could be auto negotiation or auto detect You can select the auto mode in System Configuration page Speed You can select the operation speed here when auto is disabled Duplex You can select the operation duplex mode when auto is disabled Flow Control On Flow Control function is disabled by default You can enable it here Click Apply after any modification 39 In the page users can enable disable spanning tree function and configure the bridge parameters Please refer to 9 14 of Section 6 2 for the details of these parameters Press Apply after any modification Configuring port parameters for spanning tree press Configuration STA Port and the configuration page will appear gt rate pen Te EE z n E a r De mm ooo p eitegs 1 Users can select a port number and check its spanning tree status Users can also modify these parameters Please refer to 9 14 of Section 6 2 for the details of these parameters Press Apply after any modification 40 4 Dynamic Mac Address Table Dynamic MAC Address Table Destination Port MAC Address 00 00 61 08 45 95 O0 aa
14. Description Set storm control rate as 3 3 Rate Control Rate 0 3 3 1 5 2 10 3 20 set stormcontrol bc this subcommand is for broadcast storm control set stormcontrol mc this subcommand is for multicast storm control set stormcontrol fd this subcommand is for flooding storm control Syntax set stormcontrol bc mc fd all none byport port 1 0 Examples 1 Set stormcontrol bc all Description Set storm control to suppression broadcast packet for all port Examples 2 Set stormcontrol mc none Description Set storm control not to suppression multicastcast packet for all port Examples 3 Set stormcontrol fd byport Description Set storm control to suppression flooding packet according to each port setting Examples 4 Set stormcontrol fd 1 1 Description Set storm control to suppression flooding packet for port 1 enabled 10 Show command This command is used to show configurations of the switch Here is the sub command for showing different configuration gt show Command List Penia Help commands Help commands 26 atl Show ARL table dynamic Show dynamic learning table Clg Show system configuration Show network configuration Show IGMP configuration Show mirror configuration E Show Auto mode setting Show switch port configuration Show QoS configuration Show snmp configuration Show all TRUNK groups with their members KS Show Spanning Tree setting L Show HTTP Pro
15. aa aa aa bb 00 20 ed 37 29 11 O0 e0 18 al o4 d 00 80 c8 bf 10 b6 00 c0 f5 b0 23 2d 00 c0 f6 b2 8b 2a 00 c0 5 00 83 12 00 dd dd 00 00 01 EISES P Add to Static Address Table This web page will show the Mac address table content of the switch for connection ports Select the port first and the Mac address learned by the switch on the port will be shown Up to 128 Mac addresses will be shown Users can select the Mac addresses that will be assigned as the static Mac addresses for the port here Click Add to Static Address Table after the selection Then the selected Mac addresses will be moved to Static Mac Address table and will not be shown in this table any more Users can click Static Address Table at the left side of the web page to check the static address assignment For the details about Static Address please refer to Section for Static Address Table Note Because of aging time operation of switch wrong Mac addresses could be found in the Mac Address Table sometimes These wrong Mac addresses are the machines that had ever accessed to the port and the switch learns them into the learning table The switch will clear them when the aging time is up Users can shorten the aging time and refresh the web page when they want to get the correct Mac address table content Then recover the aging time when the correct Mac address table content is got 41 5 Static Addre
16. full duplex backpressure for half duplex 802 1Q VLAN 4 transmit queues per ports for port based 802 1P tagged based priority operation Support IEEE 802 1D protocol 4 groups max 1 capture port for Ingress Egress traffic DA SA filtering function is supported Ver 1 Supports MIB II Interface Bridge MIB Etherlike MIB Private MIB Static Mac ID Access Limit Static Mac address access limit on port 802 1x Rate Control IGMP Out band Management In band Management Software Update Backup Yes support Authentication and Transparent modes Yes from 64Kbps to 100Mbps for both ingress and egress traffic Yes IGMP snooping function Console Telnet http SNMP by TFTP protocol Xmoden for firmware configuration 63 24 2FX Ports Model Access Method Standards Conformance Communication Rate MDI MDIX Media Supported Indicator Panel Number of Ports Dimensions Certification Power Consumption Input Power Temperature Humidity Bridging Function Switching Method Address Table Filtering Forwarding Rate Maximum Packet Size Flow Control VLAN QoS Spanning Tree Trunking Mirror Port SNMP Ethernet CSMA CD IEEE 802 3 10BASE T IEEE 802 3u 100BASE 10 100Mbps Full Half duplex auto negotiation Auto detect for each port 10BASE T 100 Ohm Category 3 4 5 twisted pair 100BASE TX 100 Ohm Category 5 twisted pair LEDs for each unit Power each port Link Act FDX 24 RJ45 TX ports 1 100F
17. function is supported Ver 1 Supports MIB II Interface Bridge MIB Etherlike MIB Private MIB Static Mac ID Access Limit Static Mac address access limit on port 802 1x Rate Control IGMP Out band Management In band Management Software Update Backup Yes support Authentication and Transparent modes Yes 64Kbps 100Mbps for ingress egress traffic Yes IGMP snooping function Console Telnet http SNMP by TFTP protocol Xmodem for firmware configuration 62 16 1FX Ports Model Access Method Standards Conformance Communication Rate MDI MDIX Media Supported Indicator Panel Number of Ports Dimensions Certification Power Consumption Temperature Humidity Bridging Function Switching Method Address Table Filtering Forwarding Rate Maximum Packet Size Flow Control VLAN QoS Spanning Tree Trunking Mirror Port SNMP Ethernet CSMA CD IEEE 802 3 10BASE T IEEE 802 3u 100BASE 10 100Mbps Full Half duplex auto negotiation Auto detect for each port 10BASE T 100 Ohm Category 3 4 5 twisted pair 100BASE TX 100 Ohm Category 5 twisted pair LEDs for each unit Power each port Link Act FDX 16 RJ45 TX ports 1 100FX module slot Port 17 430W x 105D x 44H mm CE Mark FCC Class A 12 Watts max Standard Operating 0 to 50 C 5 to 95 Non condensing Filtering forwarding and learning Store and forward 4K entries Line speed 1536 Bytes Auto detect Enable Disable state 802 3x for
18. is private This switch supports up to five trap receivers with different trap community names 60 7 Software Update and Backup This switch supports software configuration backup and update restore functions It could be done in three ways 1 From console when booting by Xmodem protocol and doing by terminal program This function can be used for run time code and boot code updating Boot code works only at boot time before the main program starts Press Ctrl C when the switch is booting the following message will be shown Boot Menu 0 Start the Run time code 1 Upgrade Run time code 2 Upgrade Boot Code gt Select a Start Run time code This option will continue the booting process b Upgrade Run time code This option will try to update run time code main code from terminal program with Xmodem protocol If this option is selected the following message will be shown Waiting to receive file by Xmodem Then user can select Send File function of terminal program and select Xmodem protocol and the update file then start the file upgrade c Upgrade Boot Code This option will try to update boot code from terminal program with Xmodem protocol User can select Send File function of terminal program and select Xmodem protocol and the update file then start the file upgrade 2 From console Telnet when running Doing by TFTP protocol and it will need a TFTP server in network
19. port 1 ingress rate control with 10 64K 640K Rate No Limit N 0 Rate N 64 Kb with N 1 28 Rate N 27 1Mb with N 29 127 set ratecontrol drop 0 1 this subcommand is used to enable disable the packet dropping operation when ingress traffic exceeds the maximum ingress rate If it is set to disable flow control operation will be used instead of packet dropping 25 set ratecontrol ingress egress port 0 127 this subcommand is used to set the maximum traffic rate for ingress egress traffic through physical ports of the switch The rate control could be from 64Kbps to 100Mbps N 0 rate control is disable rate No Limit N 1 28 rate Nx64Kbps for rate 64K 128K 1792Kbps control N 29 127 rate N 27 x1Mbps for rate 2M 3M 100Mbps control 9 21 set stormcontrol command This switch supports broadcast storm multicast storm and flooding storm control functions With this command you can configure the storm control function of the switch Syntax set StormControl arg_1 data_1 arg_1 data_1 arg_n data_n Argument List rate Set Control Rate for Storm Control bc Set Broadcast Control for each Port UE Set Multicast Control for each Port fAs Set Flooding Control for each Port set stormcontrol rate this subcommand is used to set the maximum storm rate that is allowed for the control Syntax set stormcontrol rate rate Examples Set stormcontrol rate 0
20. show dot1x config radius port config show 802 1x protocol status radius show radius server status port show ALL ports status For example gt show dot1x config 802 1x Configuration 802 1x Protocol Disabled Re authentication Disabled Re authentication Timeout Period 3600 Re authentication Max Count 2 Max Request Count 2 Server Timeout Period 30 Supplicant Timeout Period 30 Quiet Timeout Period 60 Tx Timeout Period 30 gt show dot1x radius Redius Server Configuration Menu Redius Server IP Address 192 168 1 222 Redius Server Port Number 1812 Security Key 12345678 gt show dot1x port 802 1X Port Authentication Configuration Menu PORT Status Au Mode ONOORWONM i m gt The Auth Mode could be Auto FA Forced Authenticated FU Forced Unauthenticated and No No 802 1x function 10 18 show security command will show current Mac address security mode for port Its syntax is gt show security MAC Security Configuration Port Static MAC Number Security Control 1 0 No Security 2 0 No Security 32 3 0 No Security 4 0 No Security 5 0 No Security 6 0 No Security 7 0 No Security 8 0 No Security The Security Control could be No Accept Reject modes No is for no Mac address security Accept is for only the static Mac address can access Reject is for only the static Mac address cannot access 10 19 show ratecontrol command will show current
21. 0m 328 feet 10BaseT FS Cat 3 4 5 Twisted pair cable e e PC Max 100m 328 feet 3 2 Connecting to Another Ethernet Switch Hub This Intelligent Switch can be connected to existing 10 Mbps or 100 Mbps hubs switches Because all UTP ports on the Intelligent Switch support Auto MDI MDI X function you Can i connect from any UTP port of the lt Ger Intelligent Switch to the MDI or Bee ES MDI X port of another hub switch with Straight Through or Crossover cables Max 100m 328 feet TO MDI or MDL X port 3 3 Application A switch can be used to overcome the hub to hub connectivity limitations as well as improve overall network performance Switches make intelligent decisions about where to send network traffic based on the destination address of the packet As a result the switch can significantly reduce unnecessary traffic The example below demonstrates the switch ability to segment the network The number of nodes on each segment is reduced thereby minimizing network contention collisions and boosting the available bandwidth per port With management function of the switch network administrator is easy to monitor network status and configure for different applications Another Ethernet Switch SC Hub Switch P Hub Switch Vs e Ras sg Sen k Power User SS Ne Workgroup Workgroup LU ef 4 Adding Module 4 1 Adding 100BaseFX Module for 16 1FX 24 2FX model The 16 1FX 24 2FX model ha
22. 4 5 6 7 8 Monitored Port s m m e ef ffe e D D Filter Mode allPackes DA SA Capture Frequency Mirror one of Packets Apply Follow the steps to configure Mirror function a Enable Mirroring first b Select the capture port c Select the monitored port from Ingress or Egress table depending on the traffic direction d Select the capture mode All packets or for some special DA SA address If DA SA is selected enter the special Mac address in XX XX XX XX XX XX format e Select the capture frequency f Press Apply button If users want to disable Mirror function select Disable and click Apply Note For 24 2FX model the capture port and monitored port is suggested at the same port groups Port 1 8 9 16 17 24 are three port groups 51 13 QoS Qos QoS Enable Disable Apply Port Priority Port Number a a a Ee a es Ers Deh Ieleteielelieteleleieleleleleleie Low eleleieleieleieieleieieleieiels Apply Flow Control Port Number a a ea a EAEAN eee BEG On lolololclelolclolo o lololel solelo Of elce elelelelejlelejlelejlelejlejleje Apply This switch supports four priority queues on each port for QoS operation Follow the steps to configure QoS function a b Enable QoS first If port based priority is used select ports for High and Low priorities The packets from High
23. 5 0 KE FOR TART Tn ALA GE Inteligent Switch CEA G URRE Outlook Expws C BAManmalEtherSW CEA Photolmpect EI Red Miam 75am fo EF OS Left part of the homepage is a function list Users can select one of them for status monitoring or switch configuration 35 Upper part of the homepage is the link status of the switch Three different colors are used to show different status of ports Link Up Link Down and Port Disable Middle part of homepage is the main operation area for each function The details about management with http connection will be shown in the following sub sections 36 1 System Configuration EELER emis fe eee Ee a pums mm Network Mask 2552552550 i 37 System Configuration is the homepage of the switch Users can find firmware version and Mac address of the switch in this page And users can configure the following items in this page a Auto Mode User can select the auto function of connection port here For Auto Negotiation mode the switch will do auto negotiation ON OFF when the auto mode of port is enabled disabled But the Auto MDIX function will also be disabled when the auto negotiation function of port is OFF For Auto Detect mode the switch will always keep auto negotiation function ON but just modify its attribution if the auto mode of port is disabled The Auto MDIX function will be always enabled in this mode For applications you shou
24. AN status and settings Its syntax is gt show iqvlan Syntax show 1qvlan status static table pvid 30 status show 802 1q Ingress Filter and GVRP protocol status static show STATIC VLAN table content table show ALL VLAN table content pvid show the PVID of ports For example gt show iqvlan status 802 1Q VLAN Enable Ingress Filter Disable Curent Block 0 Active VID lt 0 511 gt Curent VLAN Mode SVL gt show iqvlan static Static 802 1Q VLAN Table VLAN ID 1 0x001 VLAN Name Default VLAN Tagged Member Port Untagged Member Port 1234567 8 VLAN ID 2 0x002 VLAN Name Tagged Member Port Untagged Member Port ee Finish gt show iqvlan table All 802 1Q VLAN Table VLAN Type STATIC VLAN ID 1 0x001 VLAN Name Default VLAN Tagged Member Port Untagged Member Port 1234567 8 VLAN Type STATIC VLAN ID 2 0x002 VLAN Name Tagged Member Port Untagged Member Port SES Finish gt show iqvlan pvid PORT PVID The PVID of Management Port is for the management interface of the switch Only the users in the VLAN with VLAN ID equal to the PVID of Management Port can manage the switch from network because they are in the same VLAN 31 10 17 show dot1x command will show current 802 1x status and settings Its syntax is gt show dot1x Syntax
25. Al C None ByPort Ami Multicast Control C AN C None De Ee E Flooding Control C Al None ByPort Am Pot Broadcast Multicast Flooding 1 e e O 2 a a a 3 D IR BR WEE m D RE RE I 5 e e P 6 a m D 7 P e D _ m D wg L The storm control function can limit the maximum traffic rate for packet storm There are three traffic storms could be limited broadcast storm multicast storm and flooding packet storm You can enable the storm control by port Follow the steps to do the storm control settings 1 Select the control rate 2 Select which storm will be controlled and which ports will be applied all of the ports none of the ports or selected by port in the table 3 If By Port is selected select the ports that will apply the storm control Note Broadcast it is one to all traffic Every port will receive the packets Multicast it is one to many traffic Some ports in a group will receive the packets Flooding it is one to all traffic caused by Mac address not found in the switch Every port will receive the packets 55 16 SNMP In this page users can configure GET SET Trap Community Name and the IP address for trap operation Then users can manage this switch with these settings from SNMP management program 56 17 IGMP IGMP IGMP Snooping Enable C Disable Apply Member
26. ON OF THE MANAGEMENT EUNGCTIONS 7 6 2 MANAGEMENT WITH CONSOLE CONNECTION sssssssssssesesesesesesesesenesenesenesesesesene 10 6 3 MANAGEMENT WITH HTTP CONNECTION 35 6 4 ABOUT TELNET INTERFACE sonssnnesonooennnenooosennrereoosernrererossnnrerrrosennnrrrresennrnrene 60 6 5 ABO T SN MEINEBENEE eisir A0 eege eege deg Ee 60 7 SOFTWARE UPDATE AND BACKUP seen 61 A PRODUCT SPECIFICATIONG ccccccceeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeseseseeeeeseesesenees 62 B COMPLIANCE EE 65 C WARRANTY ccccccccetesenesenesenesseesseesessaessaessnesseesaessaessneseneusneaseesseesaeeaaeeaa 66 1 Introduction There are three models for the Intelligent Switch Series 8 UTP ports model 16 UTP 1 100BaseFX module ports model and 24 UTP 2 100BaseFX module ports model This Intelligent switch is a Layer2 management switch with lots of advanced network functions including VLAN trunking spanning tree mirror port IP multicast rate limit and port configuration It supports console telnet http and SNMP interface for switch management IEEE 802 1x is supported for port security application These functions can meet most of the management request for current network 1 1 Package Contents One Intelligent Switch One AC power cord for AC power model One console cable Two rack mount kits and screws for 16 1FX 24 2FX model only This user s manual 2 Where To Place the Intelligent Switch This Intelligent Switch can be place
27. X module slot for one or two 100FX port Port 25 26 440W x 172D x 43H mm CE Mark FCC Class A 13 Watts max Full range 100 to 240V 50 to 60 Hz Standard Operating 0 to 50 C 5 to 95 Non condensing Filtering forwarding and learning Store and forward 4K entries Line speed 1536 Bytes Auto detect Enable Disable state 802 3x for full duplex backpressure for half duplex 802 1Q VLAN 4 transmit queues per ports for port based 802 1P tagged based priority operation Support IEEE 802 1D protocol 4 groups max 1 capture port for Ingress Egress traffic DA SA filtering function is supported Ver 1 Supports MIB II Interface Bridge MIB Etherlike MIB Private MIB Static Mac ID Access Limit Static Mac address access limit on port 802 1x Rate Control IGMP Out band Management In band Management Software Update Backup Yes support Authentication and Transparent modes Yes from 64Kbps to 100Mbps for both ingress and egress traffic Yes IGMP snooping function Console Telnet http SNMP by TFTP protocol Xmodem for firmware configuration 64 B Compliances EMI Certification FCC Class A Certification USA Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A digital device pursuant to Sub
28. a specified trunk group Ee Destroy a specified VLAN gt Delete static entries in ARL table gt del arl 11 Del ARL xx xx xx xx xx Xxx port XX XX XX XX XX XX s a assigned static Mac ID in ARL table of the switch You can remove it from the table with the command For example del arl 00 11 22 33 44 55 3 will delete the Port 3 static Mac ID 00 11 22 33 44 55 from ARL table gt Disable Mirror function gt del mirror Disable mirror function gt Remove All Ports in a Trunk Group gt del trunk Syntax Del TRUNK trunk trunk is the trunk group number and all the trunk ports in this trunk will be removed by this command For example del trunk 3 will remove all trunk ports from Trunk 3 and Trunk 3 becomes a null trunk gt Delete a802 1Q VLAN gt del 1qvlan Syntax del 1qvlan Vid This command will delete the 802 1Q VLAN with the VLAN ID For example del 1qvlan 5 will delete the 802 1Q VLAN with VLAN ID 5 3 Find command The find command can find an Mac address in the ARL table Enter find at the prompt the command syntax will be shown gt find Command List KEE EEN Help commande help Help commands ar Search a specified MAC address in ARL table The syntax is as follow gt find arl Find ARL Xx xx xx xX XX Xx If the Mac address is in ARL table it will be shown as follow gt find arl 00 c0 f6 1 1 22 33 This MAC 00 c0 f6 1 1 22
29. an one switch in the network users can configure this function for their network spanning tree application 4 Port Mirror This switch operates in store and forward algorithm so it is not possible to monitor network traffic from another connection port But the port mirror function could copy packets from some monitored port to another port for network monitor This switch also provides DA SA filtering function for monitoring the traffic to from some user 5 QoS For Quality of Service request in a network packets could be classified to different forwarding priorities For real time network traffic like video audio it needs higher priority than normal network traffic With the definition of packet priority it could have 8 priority levels from 0 to 7 This switch supports four priority level queues on each port It could be configured for port based or 802 1P tagged based User can define the mapping 0 7 to the four priority queues 6 Static Mac ID in ARL table The switch can learn the Mac address from user s packets and keep these Mac address in the ARL table for store and forward table lookup operation But these Mac addresses will be deleted from ARL table after some time when users do not send any packets to the switch This operation is called aging and the time is called aging time It is 5 minutes normally it could be changed by users If users want to keep a Mac address always in ARL table for some port they can assign
30. and you can find the command list as follow gt help Command List ee Ae Help commande backup Backup run time firmware or configuration file del Del commande find Find commands ect Logout help Help commands logout Logout ping Ping a specified host with IP address reset Reset system or reset factory default setting Set Set commands Show Show commands Upgrade Upgrade run time firmware or configuration file Here is the detail about these commands 1 Backup command This switch supports TFTP protocol for firmware and configuration update and backup You should select backup firmware or configuration first And provide the IP address of the TFTP server and the backup file name for the backup operation Enter backup at the prompt the command syntax will be shown gt backup Syntax backup firmware config ip filename For example back config 192 168 1 80 abcd will backup the configuration to TFTP server 192 168 1 80 and its file name is abcd 2 Del command The del command can delete staic entries in ARL table disable Mirror function remove ports in a trunk group remove forwarding ports for trunk port Enter del at the prompt the command syntax will be shown gt del Command List e e Help commande wives Help commands Delete a specified MAC address from ARL table Sege Disable mirror and delete mirror capture port Laken tae Destroy
31. d on a flat surface your desk shelf or table Place the Intelligent Switch at a location with these connection considerations in mind The switch configuration does not break the rules as specified in Section 3 The switch is accessible and cables can be connected easily to it The cables connected to the switch are away from sources of electrical interference such as radio computer monitor and light fixtures There is sufficient space surrounding the switch to allow for proper ventilation the switch may not function according to specifications beyond the temperature range of 0 to 50 degrees C For 16 1FX 24 2FX model you can also install this Intelligent switch on a 19 rack with the rack mount kits as the picture 3 Configure Network Connection 3 1 Connecting Devices to the Intelligent Switch Connection Guidelines For 10BaseT connection Category 3 or 5 twisted pair Ethernet cable For 100BaseTX connection Category 5 twisted pair Ethernet cable For UTP cable connection always limit the cable distance to 100 meters 328 ft as defined by IEEE specification f your switch has 100BaseFX port you can connect long distance fiber optic cable to the switch depending on the module Because this switch supports Auto MDI MDI X detection on each UTP port you can use normal straight through cable for both workstation connection and hub switch cascading 100BaseTX Cat 5 Twisted pair cable Max 10
32. de will disable 802 1x operation on this port 49 11 Trunk Trunk Trunk Function Enable Disable Apply Port Humber 1 2 3 4 5 6 T 8 Group 1 eoleolelolaloflala Group 2 C C E e C Group 3 C oO C O C C S Group 4 C C O O O C C Non trunk C C c C C This switch supports 4 trunk groups and they are null by default If users want to use trunk function follow the steps to configure it a Enable Trunk function first b Assign ports to the trunk Then click Apply c If you want to remove ports from trunk put them to Non trunk and click Apply The selected ports will be removed from trunk groups If users want to disable trunk function select Disable and click Apply button The switch will clear the Trunk configuration About redundant application The trunk connection supports redundant function If any trunk cable is broken the traffic going through that cable will be transferred to another trunk cable in the trunk connection automatically 50 12 Mirror Mirror Mirroring Enable Disable Port Number i 2 3 4 5 6 7 8 Capture Port Ze C C Ingress Port Number 1 2 3 4 5 6 7 3 Monitored Port s D e E e e E E Filter Mode Al Pakes DA C SA Capture Frequency Misc one of Packets Egress Port Number 1 2 2
33. e authentication Max Count P 1 10 Max Request Count 2 1 10 Server Timeout Period jo 0 65535 seconds Supplicant Timeout Period 30 0 65535 seoonds Quiet Timeout Period ei 0 65535 seconds Tx Timeout Period 30 0 65535 seconds Apply Radius Server Configuration Radius Server IP Address i92 168 1 222 Radius Server Port Number pr Security Key 12345678 Apply The 802 1x function can limit the port access for authentication users only needs a RADIUS server for the authentication process and the switch acts as an authenticator The function here is for 802 1x function configuration 1 802 1x System Authentication Status Enable Disable Transparent Enable enable 802 1x function in authentication mode Disable disable 802 1x function Transparent only forwarding 802 1x packets Re authentication enable disable Timeout Period and Max Count The re authentication function will re authenticate users after the timeout period The Max Count is the maximum re try count between the switch and users before authentication fail Max Request Count and Server Timeout Period 48 The Server Timeout Period is the timeout period for the request between the switch and RADIUS server The Max Request Count is the maximum re try count between the switch and RADIUS server before authentication fail Supplicant Timeout Period This is the timeout value between the
34. ecome unstable because of traffic looping when more than one cable is connected between them If the switches support trunk function they can treat these cables as one connection between them The traffic looping will not happen between these cables and the switches will work stable with bigger bandwidth between them This switch supports trunk function and users can configure it with the following steps a Enable trunk function b Select the port partition for trunk c Assign ports to a trunk For example assign Port 1 2 3 for Trunk 1 Notes About redundant application The trunk connection supports redundant function If any trunk cable is broken the traffic going through that cable will be transferred to another trunk cable automatically For example if user port Port 6 is assigned to Port 1 in a Trunk and Port 1 connection breaks Port 2 will take over the traffic for Port 6 automatically It could be used for redundant application 3 Spanning Tree Protocol Spanning tree is a protocol to prevent network loop in network topology H network loop happens it will cause switches in the network unstable because more and more traffic will loop in the network If network loop happens spanning tree protocol will block one connection in the loop automatically But it will also cause a 30 seconds delay if any network connection is changed because of the network topology detection operation of the protocol Because there could be more th
35. ed to set Port VLAN ID The Port VLAN ID is used as the VLAN ID for tag adding when untagged packet is translated to tagged packet For example set 1qvlan pvid 3 10 will set the PVID of Port 3 as 10 mgrpvid sub command is used to select the VLAN group that is allowed to management the switch Only the users in the selected VLAN can manage the switch by Http Telnet and SNMP For example set 1qvlan mgrpvid 5 will allow the users in the VLAN with VLAN ID 5 to manage the switch remotely priority sub command is used to set port priority for tag adding when untagged packet is translated to tagged packet For example set 1qvlan 22 priority 3 2 will set the port priority of Port 3 as 2 The priority information in tag will be filled with 2 when the untagged packet coming to Port 3 is translated to tagged packet block sub command is used to set active VLAN ID block range for 802 1Q VLAN operation The valid VLAN ID number is 1 4094 Because this switch can support up to 512 active VLAN ID number the valid VLAN ID number is divided into eight blocks as below Syntax set 1qvlan block Block Examples Set 1qvlan block 0 Description Set current block as 0 and active VID 1 511 Block Active VID Block Active VID 0 1 511 4 2048 2559 1 512 1023 5 2560 3071 2 1024 1535 6 3072 3583 2 1536 2047 7 3584 4094 Select one of the blocks and only the selected VLAN ID range is active for 802 1Q VLAN operation of the switch mode sub com
36. efer to the description for set qos flowctrl command for the details For exampe set port 1 name YYY admin enable speed 10 duplex half command will enable Port 1 and set it to 10Mbps Half Duplex and name it as YYY 9 11 set qos command This command is used to configure QoS function of the switch Its syntax is gt set qos Syntax set QoS arg_1 data_1 arg_1 data_1 arg_n data_n Argument List enable Set QoS enabled disable Set QoS disabled priority Set QoS priority of specified port flowctrl Set QoS flow control of specified port mapping Set 802 1p priority to priority queue mapping This switch supports four priority queues on each port PO P1 P2 and P3 Both port based priority and 802 1P tag priority are supported This function can be used to configure the priority queues of the switch Here are the details about these sub commands 9 11 1 set qos enable command This command is used to enable QoS operation 9 11 2 set qos disable command This command is used to disable QoS operation 9 11 3 set qos priority command This command is used to configure port based priority All packets coming from high priority port will always be forwarded to highest priority queue P3 All packets coming from low priority port will always be forwarded to lowest priority queue PO For example set gos priority 3 high command will set Port 3 as a high priority port
37. eticmole vih Repet foncion e Mew i OO u ajvo Sj i wy El O fee ioe o Apply This function is used to set the security modes for static Mac address on the port There could be three options for this function 1 No Security No any Mac address access limitation for the port i e every Mac address could access network via the port 2 Static mode with Accept function Only these static Mac address can be accepted by the port i e only the user with the static Mac address can access network via the port 3 Static mode with Reject function Only the static address will be rejected by the port i e other Mac address except the static Mac address can access network via the port 43 7 802 1Q VLAN Configuration 802 1Q VLAN Configuration GVRP Protool C Enable Disable Ingress Filter C Embe Disable VLAN Mode on C WL C SVLNL Apn y d 2 d Active VLAN ID BlockO 1 511 d zech Port VID Management Port EO O Apy 1 ft fo D 2 z ox a Ee e A This function is used to configure 802 1Q VLAN function 802 1Q VLAN This function can enable disable 802 1Q VLAN operation GVRP Protocol The GVRP protocol can learn remote 802 1Q VLAN on other devices and add to dynamic 802 1Q VLAN table You can enable disable the operation of this protocol Ingress Filter The ingress filter function is for doing VLAN
38. f the switch Its syntax is gt set snmp Syntax set snmp arg_1 data_1 arg_1 data_1 arg_n data_n Argument List name Set system name location Set system location contact Set system contact name getcommunity Set GET community setcommunity Set SET community trapcommunity Set TRAP community trapip Set TRAP IP address txtrap Send Trap for test User can use the command to configure the following items for SNMP operation a Name of the switch with name sub command b Location of the switch with location sub command c Contact for the switch with contact sub command d GET Community string with getcommunity sub command e SET Community string with setcommunity sub command f TRAP Community string with trapcommunity sub command g TRAP IP Address with tapip sub command h Test TRAP Operation with txtrp sub command For example set snmp name ABC location AAA 1F contact Jack command will set these SNMP information to switch 9 13 set trunk command 19 This switch supports four trunk groups Trunk 1 4 maximum They are disabled and null trunk groups default Users can use this command to configure trunk function of the switch Its syntax is gt set trunk Syntax Set trunk enable Description Enable trunk function Syntax Set trunk disable Description Disable trunk function Syntax Set trun
39. figure the mirror operation for ingress traffic Its syntax is gt set mirror ingress Syntax set mirror ingress arg_1 data_1 arg_1 data_1 arg_n data_n Argument List div Set mirror ingress egress div d mode Set mirror ingress egress mode ALL SA DA MAC Set mirror ingress egress Mac xx Xx XX XX XX XX monitor Set mirror ingress egress monitor xx xx xx set mirror ingress div x every x packets capture one for mirror For example set mirror ingress div 10 will capture one packet from every ten packets from ingress traffic set mirror ingress mode xx mirror all packets or mirror packets with some DA or SA only For example set mirror ingress mode all will mirror all packets set mirror ingress mac XX XX XX XX XX XX if the mirror mode is for the packets with some DA SA users can assign the DA SA here set mirror ingress monitor xx xx xx set the monitored ports here For example set mirror ingress monitor 1 2 5 will mirror the ingress traffic from Port 1 2 5 Notes If the monitored traffic exceeds the maximum bandwidth of capture port flow control function will work on these monitored ports 9 7 3 set mirror egress command This command is used to configure the mirror operation for egress traffic Its syntax is similar to the mirror operation for ingress traffic Please refer to set mirror ingress command section 9 7 4 set mirror port command This command i
40. filtering at ingress port If the VLAN of the packet is in the same VLAN of the ingress port it will be forwarded to egress port Otherwise it will be discarded 44 VLAN Mode This function can select different VLAN modes of 802 1Q VLAN operation There are three modes for VLAN function SVL Shared VLAN IVL Individual VLAN and SVL IVL SVL mode the switch will do packet forwarding according to its Mac address only IVL mode the switch will do packet forwarding according to its Mac address and its VLAN ID SVL IVL mode its operation is the same as IVL mode but for untagged port is used as the uplink port in MDU MTU application For most VLAN applications SVL mode is OK Active VLAN ID This function is used to set active VLAN ID block range for 802 1Q VLAN operation The valid VLAN ID number is 1 4094 Because this switch can support up to 512 active VLAN ID number the valid VLAN ID number is divided into eight blocks as below Block Active VID Block Active VID 0 1 511 4 2048 2559 1 512 1023 5 2560 3071 2 1024 1535 6 3072 3583 3 1536 2047 7 3584 4094 Select one of the blocks and only the selected VLAN ID range is active for 802 1Q VLAN operation of the switch Port VID This setting is for untagged packet translated to tagged packet The Port VID and Priority Setting will be used for tag adding in the translation The Management Port is the management interface of t
41. he switch You can configure its PVID here It will limit only the users in the VLAN with VLAN ID equal to Management Port PVID can manage the switch from network by Http Telnet and SNMP 45 8 Static 802 1Q VLAN Static 802 1Q VLAN Create New Static VLAN VLAND Eji VLAN Name i T l if Maximum length 16 Create Show Static VLAN Table Select VLAN 1 x001 e VLAN D VLAN Type VLAN Name 1 STATIC Default VLAN Peer 1 2 3 4 5 6 7 8 S O T 12 13 4 15 t6 Del e lelelel ele elelelel elelelelele Tat Ieleleieleieieleieleieleleielelie Namme CO TolTo eloe elole cle clelele ec e You can create static 802 1Q VLAN group here You need to input the VLAN ID and VLAN Name to create a VLAN The valid VLAN ID is 1 4094 The VLAN ID should be in the active VLAN ID block set in 802 1Q VLAN Configuration page After a VLAN is created you can select the VLAN in Show Static VLAN Table to get the configuration of the VLAN The new VLAN is empty by default You can select the port for the VLAN and tagged untagged for it After that click Apply to complete the VLAN configuration About Tagged Untagged The tagged port will always send out packets with tag If untagged packet is received from ingress port tag will be added with the PVID setting of ingress port before forwarded to tagged port The 802 1Q VLAN information will be carried in
42. igned to ports with fast connections Higher values will be blocked and should be assigned to ports with slow connections The suggestion values are 100 50 600 for 10M 19 10 60 for 100M and 4 3 10 for 1000M connections 9 15 set http command This command is used to enable disable the http function of the switch Because hacker or worm virus like ColdRed often attacks http server this command is provided to disable http to prevent it If this switch is installed in public Internet without any firewall protection we suggest users to disable the http interface and use Telnet or SNMP instead Its syntax is gt set http Syntax Set http enable Description Enable http protocol function Syntax Set http disable Description Disable http protocol function 9 16 set gvrp command This command is used to enable disable the GVRP function for 802 1Q VLAN If this function is enabled this switch will learn the 802 1Q VLAN from another 802 1Q network devices if it receives their packets The learned remote 802 1Q VLAN will be shown in the dynamic 802 1Q VLAN table 21 Its syntax is gt set gvrp Syntax set gvrp 1 0 lt 1 enable 0 disable gt 9 17 set 1qvlan command This command is used to configure 802 1Q VLAN of the switch Its syntax is gt set 1qvlan Syntax set 1qvlan arg_1 data_1 arg_1 data_1 arg_n data_n Argument List enable Set 802 1Q VLAN enabled disable Set 802 1Q VLAN disabled
43. ion will restore the configuration to the factory default setting reset system will reset the switch and the switch will reboot 9 Set command This command can be used to configure most functions of the switch Lots of sub commands are needed for this command Enter set at the prompt the sub command list will be shown gt set Command List CN Help commande help Help commands admin Set administrator name and password ar Add a static MAC address in ARL table etho Set network ethO configuration 13 idle Set idle time for CLI session igmp Set IGMP configuration mirror Set mirror configuration AGE eee Set switch age automode Set Auto Negotiation or Auto Detect mode port Set switch port configuration oos Set QoS configuration Snmp Set snmp configuration trunk Set a port to join leave a specified Trunk Group Sta Set Spanning Tree setting Set HTTP Protocol setting Set GVRP Protocol setting DE Set 802 1q VLAN Configuration GER Set 802 1x Configuration security Set MAC Security Configuration ratecontrol Set Rate Control Configuration stormcontrol Set Storm Control Configuration 9 1 set and set help command These two commands will show the sub command list for set command 9 2 set admin command This command can be used to modify the user name and password for administrator 9 3 set arl c
44. ion to prevent illegal users access network through the switch This switch supports MD5 TLS and PEAP authentication types 8 Rate Control This function can limit the burst traffic rate for physical ports The traffic could be ingress traffic or egress traffic This function can protect the network bandwidth usage by different users 9 IP Multicast with IGMP Snooping IP multicast function can forward packets to a group of users connected on different ports The user group is learned by the switch from the packets from IGMP active router with IGMP snooping function It is often used for video applications 10 Software Backup Update This switch supports backup and update functions for its internal software and its network configuration It could be done in three ways a From console when booting doing by Xmodem protocol and by terminal program for boot code and run time code updating b From console Telnet when running doing by TFTP protocol and it will need a TFTP server in network for run time code and configuration backup update c From web browser doing by http protocol and by web browser for run time code and configuration backup update 6 2 Management with Console Connection Please follow the steps to complete the console hardware connection first 1 Connect from the console port of the switch to COM port of PC with the console cable 2 Start the terminal program of Windows Create a new connection and select COM po
45. k port trunk Examples Set trunk 1 5 7 1 Description Add port 1 5 to trunk group 1 and remove port 7 from trunk group 1 a enable and disable sub commands are used to enable disable trunk function of the switch b set trunk port trunk is sub command to add remove ports to from trunk groups Only Port 1 8 is available for trunk operation 9 14 set sta command This command is used to configure spanning tree protocol of the switch Its syntax is gt set sta Command List ee Help commande bein Help commande enable Enable Spanning Tree function disable Disable Spanning Tree function bridge Set Spanning Tree bridge configuration port Set Spanning Tree port configuration a set sta and set sta help commands will show the sub command list b set sta enable and set sta disable commands will enable disable spanning tree function of the switch c set sta bridge command is used to configure for the switch Its syntax is gt set sta bridge Syntax set sta bridge arg_1 data_1 arg_1 data_1 arg_n data_n Argument List priority Set bridge priority hello Set bridge hello time Set bridge maximum age Set bridge forward delay time priority 0 65535 Bridge priority is for selecting the root device root port and designated port The device with the highest priority lowest value becomes the STA root device If all devices have the same priori
46. ld select Auto Detect mode if the connected device is auto negotiation enabled And you can select Auto Negotiation mode if the connected device is auto negotiation disabled For most applications Auto Detect mode is OK Aging time Users can enable disable the aging operation of the switch and modify the aging time here Default is 300 seconds System Name Location Contact These information is useful for switch management in a network system It is the same information used in SNMP protocol DHCP IP Address Network Mask Gateway This switch supports DHCP client function If DHCP Client is enabled this switch will try to get the IP configuration from DHCP server If DHCP server is not found it will use the default IP 192 168 1 5 instead If DHCP Client is disabled you can set IP address configuration of the switch here This switch will reboot itself after any IP configuration is modification Administrator Configuration This is for network administrator to change his her username and password Default is admin 123456 If any modification click Apply to activate the new setting 38 2 Port Configuration Port Configuration Port Number Link Disable Avto Speed Duplex Flow Control On 3 Down Li Enable e Dm ES a 3 Down D Enable fiom Half gt H 4 Down RW Enable fiom d Half D 5 Down D Enable e Dm a Hal x P 6 Down E Enable fiom d Half e
47. mand is used to select the VLAN mode for 802 1Q VLAN operation There are three modes for VLAN function SVL Shared VLAN IVL Individual VLAN and SVL IVL Syntax set 1qvlan mode 0 SVL 1 IVL Examples Set 1qvlan mode 0 Description Set current vlan mode as SVL 0 SVL mode 1 IVL mode 2 SVL IVL mode SVL mode the switch will do packet forwarding according to its Mac address only IVL mode the switch will do packet forwarding according to its Mac address and its VLAN ID SVL IVL mode its operation is the same as IVL mode but for untagged port is used as the uplink port in MDU MTU application For most VLAN applications SVL mode is suggested 9 18 set dot1x command This command is used to configure the 802 1x function of the switch Its syntax is gt set dot1x Syntax set dot1x arg_1 data_1 arg_1 data_1 arg_n data_n Argument List enable Set 802 1x enable disable Set 802 1x disable transparent Set 802 1x transparent re au Set 802 1x Re authentication reauthtime Set 802 1x Re authentication Timeout Period reauthcnt Set 802 1x Re authentication Max Count reqcnt Set 802 1x Max Request Count sertime Set 802 1x Server Timeout Period supptime Set 802 1x Supplicant Timeout Period quiettime Set 802 1x Quiet Timeout Period txtime Set 802 1x Tx Timeout Period 23 SIP eee Set Radius Server Address authport Set Authenticate Port
48. n Users can manage the switch with Http Web Browser connection Before http connection IP address configuration of the switch should be done first Please follow the instruction in Section 6 2 to complete the console connection and use show net command to check IP address of the switch first If users want to change the IP address of the switch use set ethO ip xxx xxx xxx xxx netmask XXxX xXX XXX XXX gateway XXX XXX XXX XXX command to modify the IP address of the switch The default IP configuration is 192 168 1 5 and mask 255 255 255 0 After IP address configuration done and the switch is connected to network users can start Http connection by entering IP address of the switch to the web address line in Web Browser A login screen will be prompted for user name and password The default user name and password is admin 123456 Then the management homepage will appear Web Based Masayement Funchon Microsoft Internet Explorer 2 5 x GZD WO MO OARA IAM Ne vi gt x 2 me year G en BR JB ED E ie wei i68 1 2 gt EI GE Moron Antivies G Link Up Link Down Post Disable System Configuration Main Board Information Fre Verson 2 08 02 e Dec 4 2003 17 27 16 gt Mac Address 00 C0 F6 74 L1 11 Port Number 16 ARL Agng Ente Disable ARL Aging Time seconds 15 System Information System Name Location P Addes 192 168 1272 Nerwock Mask 255 255 25
49. of Radius Server shkey Set 802 1x Security Key portauth Set 802 1x port auth mode enable sub commands is used to enable 802 1x authentication function disable sub command is used to disable 802 1x function transparent sub command is used to set the operation of 802 1x function to transparent mode In this mode the switch will forward the 802 1x packets only re_au sub command is used to enable the re authentication function of the switch When the re authentication time is up the switch will start the re authentication process reauthtime sub command is used to set the timeout period of the re authentication process reauthcnt sub command is used to set max count for re authentication request in the re authentication process If the max count is met it will become un authentication state The valid value is 1 10 reqcnt sub command is used to set max request timeout count between the switch and RADIUS server before authentication fail The valid value is 1 10 sertime sub command is used to set the request timeout value between the switch and RADIUS server The valid value is 0 65535 supptime sub command is used to set the timeout value between the switch and users called supplicant in 802 1x after first identification The valid value is 0 65535 quiettime sub command is used to set the quiet time value between the switch and the user before next authentication process when authentication fail
50. ommand This command is for adding static Mac ID to ARL table of the switch It syntax is gt set arl Set ARL xx xx xx Xxx Xxx xx port For example set ARL 00 c0 f6 1 1 22 33 5 will add a static Mac ID 00 c0 f6 1 1 22 33 to ARL table for Port 5 and this Mac ID will never be aged out from Port 5 Note Because the static Mac address is fixed on the assigned port by the switch the static Mac address can access network through the assigned port only It will fail to access network through other ports of the switch 9 4 set eth0 command This command is used to configure IP address of the switch Its syntax is gt set ethd Syntax set eth0 arg_1 data_1 arg_1 data_1 arg_n data_n Argument List Chases Set DHCP client Set IP Address estes Set netmask bau Set gateway IP address 14 9 5 9 6 9 7 This switch supports DHCP client function If you set DHCP enable it will try to get IP configuration from DHCP server when it boots up You can use show net command to check the DHCP setting and current IP configuration of the switch If DHCP is enable and the switch cannot find a DHCP server in the network a message BOOTP DHCP failed on eth0 will be shown and it will use 192 168 1 5 255 255 255 0 as its IP configuration If you set DHCP disable you can set the IP configuration with jp netmask and gateway commands For example set ethO ip 192 168 1 250 netmask 255 255 255
51. part B of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures are required to correct the interference CE Mark Declaration of Conformance for EMI and Safety EEC This is to certify that this product complies with ISO IEC Guide 22 and EN45014 It conforms to the following specifications EMC EN55022 1988 CISPR 22 1985 class A EN60555 2 1995 class A EN60555 3 IEC 1000 4 2 1995 4kV CD 8kV AD IEC1000 4 3 1995 3V m IEC1000 4 4 1995 1kV power line 0 5kV signal line This product complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC Warning Do not plug a phone jack connector in the RJ 45 port This may damage this device 65 C Warranty We warrant to the original owner that the product delivered in this package will be free from defects in material and workmanship for a period of warranty time from the date of purchase from us or the authorized reseller The warranty does not cover the product if it is damaged in the process of being installed We recommend that you have the company from whom you purchased this product install it 66
52. priority port will be forwarded to highest priority queue on egress port And the packets from Low priority port will be forwarded to lowest priority queue on egress port There is also a Flow Control ON option in Port Configuration page If Flow Control is ON at both Port Configuration page and QoS page the Flow Control function of a port is ON Otherwise it is OFF If you don t expect any packet lost set the Flow Control function ON But it will conflict with the real QoS request because packets will be paused by the switch when congestion happens And the switch can not do the QoS request for the packets For 802 1P tagged packet its priority value is 0 7 Select the ports that enable the 802 1P priority function i e it will forward packet with the priority information in tag Then you can configure the 802 1P priority mapping to priority queue of port Please see the picture below Click Apply to activate the setting after configuration If you want to disable QoS operation select Disable and click Apply button 52 802 1P Priority Tag 7 802 1P Priority Tag 6 802 1P Priority Tag 5 802 1P Priority Tag 4 802 1P Priority Tag 3 802 1P Priority Tag 2 802 1P Priority Tag 1 802 1P Priority Tag 0 53 14 Rate Control Ingress Egress Rate Control Packet Drop for Ingress Limit C Enable Disable Apply rate N 64Kb with N 1 28
53. rate control setting for each port For example gt show ratecontrol Rate Control Configuration Drop Packet for Ingress Limit Disable Port Ingress Egress 1 Disable Disable 2 Disable Disable 3 1280Kb Disable 4 Disable Disable 5 Disable 40Mb 6 Disable Disable 7 Disable Disable 8 Disable Disable 9 Disable Disable 10 Disable Disable 11 Disable Disable 12 Disable Disable 13 Disable Disable 14 Disable Disable 15 Disable Disable 16 Disable Disable 10 20 show stormcontrol command will show current packet storm control settings This switch supports broadcast storm multicast storm and flooding storm control functions With this command you can find the maximum storm rate setting and the port list doing the storm control For example gt show stormcontrol Storm Control Configuration Control Rate 3 3 Broadcast Control By Port Multicast Control By Port Flooding Control By Port 11 Upgrade command This switch supports firmware or configuration upgrade with TFTP protocol This command is used to upgrade firmware or configuration to the switch Its syntax is gt upgrade Syntax upgrade firmware config ip filename ip is the IP address of TFTP server filename is the upgrade file name in the TFTP server For example upgrade config 192 168 1 80 abcd command will load file abcd from TFTP server 192 168 1 80 as its configuration setting 34 6 3 Management with Http Connectio
54. ress 224 0 0 9 Member Port 1 Group 2 IP Address 224 0 0 2 Member Port 1 Group 3 IP Address 224 2 188 136 Member Port 4 5 10 7 show mirror command will show mirror function configuration of the switch For example gt show mirror Mirror Configuration Mirror Switch Disabled Capture port 1 Ingress DIV 3 Mode SA MAC 00 C0 F6 1 1 22 33 Port List 2 Egress DIV 1 Mode ALL MAC 00 00 00 00 00 00 Port List This setting will mirror those packets that with source Mac address OOCOF6112233 ingress to Port 2 to Port 1 for every three matched packets 10 8 show automode command will show current auto mode setting for port configuration It could be Auto Negotiation and Auto Detect For Auto Negotiation mode the switch will do auto negotiation ON OFF when the auto mode of port is enabled disabled But the Auto MDIX function will also be disabled when the auto negotiation function of port is OFF For Auto Detect mode the switch will always keep auto negotiation function ON but just modify its attribution if the auto mode of port is disabled The Auto MDIX function will be always enabled in this mode For applications you should select Auto Detect mode if the connected device is auto negotiation enabled And you can select Auto Negotiation mode if the connected device is auto negotiation disabled For most applications Auto Detect mode is OK 10 9 show port command will show status and configuration of each switch port For e
55. rt of PC used for the console Set the configuration of the terminal as 38400 8 N 1 You can find the terminal program in Start gt Programs gt Accessory Programs gt Communication gt Terminal If you cannot find it please install it from your Windows Installation Disk Please refer to your Windows user manual for the installation 3 Power on the switch If everything is correct the booting screen will appear in the terminal program when the switch is powered on It will stop at the following screen after some initializing messages Booting Program Version 1 01 00 built at 16 06 25 Feb 19 2003 RAM 0x00000000 0x00800000 0x0000cc78 0x007f3000 available FLASH 0x05800000 0x05900000 16 blocks of 0x00010000 bytes each gt enter C to abort booting within 3 seconds Start to run system initialization task System Configuration Company Name Model Name Intelligent Switch MAC Address 00 C0 F6 71 71 71 Firmware Version 2 08 02 Press lt ENTER gt key to start UCD SNMP version 4 1 2 Press Enter key user name and password will be requested The default user name and password is admin 123456 After login the switch a prompt will be shown Because this switch supports command line for console interface you can press or help to check the command list first Note Management with Telnet connection has the same interface as console connection 10 With help comm
56. s Group Total 3 Group Group Address Members Port 224 0 0 2 3 239 255 255 250 224 0 0 9 The IGMP function is for IP multicast operation in network This switch can do IGMP Snooping function to get the IP multicast group information from IGMP active device The learned IP multicast member group will be shown in the IGMP web page This switch will forward IP multicast traffic to these member ports that it learned in the group information The IGMP snooping function can be enabled disabled in this page 57 18 Statistics Users can find the traffic statistics here Select port number to get the counters for different port Users can modify the refresh interval to get different counter updating period Click Refresh button can update the counter immediately Users can reset counters to zero with the Reset Statistics button 58 19 Tools Maintenance Tools System Backup Please press the Backup Setting button to save the configuration data to your pe Backup Setting Enter the path and name of backup file then press Restore Setting button COO O O System Restore Factory Default Settings Please press the Restore button to restore the factory default settings of the Device Restore System Reset In the event that the Device stops responding corectly or in some way stops functioning you can perform a reset Please press the Reset b
57. s a module slot for 100BaseFX connection extension at front panel You can add a 100BaseFX module to the switch and this switch gets one 100BaseFX port Port 17 25 for long distance fiber optic cable connection For 24 2FX model the module could have one or two 100FX ports with different modules and the FX port will be Port 25 26 Note This switch does not support hot swap function Turn off the power first before adding or removing module Otherwise the switch and module could be damaged Module Slot Es A P EECHER y A d eS lo y SE a d Please follow the steps to add the module to the switch Turn off the switch first Loosen the screws of slot cover and remove the cover from the module slot Slide in the module into the module slot Tighten the screws of the module to the switch Connect the fiber optic cable to the FX port of the module Power on the switch Check Port 17 25 26 configuration from Console Telnet or Web interface It should be 100Mbps full duplex AO OT CO Ns 5 LEDs Conditions Definition 5 1 LEDs Defined The LEDs provide useful information about the switch and the status of all individual ports For 8 ports model STATUS CONDITION Switch is receiving power Link Act Port has established a valid link Flashing Data packets being received or sent The connection is 100Mbps The connection is 10Mbps FDX ON The connection is Full Duplex OFF The connection is Half Duplex
58. s used to set the capture port for mirror operation For example set mirror port 3 will capture the mirror traffic to Port 3 9 7 5 set mirror enable command This command is used to enable the mirror operation 9 7 6 set mirror disable command This command is used to disable the mirror operation Note For 24 2FX model the capture port and the monitored port are suggested in the same port group Port 1 8 9 16 17 24 are three port groups 9 8 set age command This command is used to change the aging time of the switch 16 Its syntax is gt set age Syntax set age time The aging time is 300 seconds default and its valid range is 0 65535 If time is set to 0 the aging function will be disabled Notes It is different from static Mac ID in ARL table The connection port is fix for a static Mac ID but the connection port could be changed for a Mac ID with no aging 9 9 set automode command This command is used to set the auto mode function of connection ports There are two modes for it an auto negotiation and ad auto detection an mode if the auto mode of a port is disabled in port configuration the switch will disable its auto negotiation function and the Auto MDIX function of the port is also disabled That is the real force mode setting of the port ad mode the auto mode of a port is disabled in port configuration the switch will not disable its auto negotiation function but just modify its auto
59. ss Table Static Address Table MAC Address XX XX XX XX XX XX e Destination Port EZ ID MAC Address Destination Port P 00 a0 c5 16 76 63 3 Delete 2 et 8 al of d 3 Des 3 KEEN 3 Deel This switch supports static Mac address assignment Users can assign static Mac addresses by the two methods a Select from the Mac address list in Dynamic Mac Address Table page b Assign manual Enter a Mac address and select the port then add this entry to the static Mac address table The switch will not age out these static Mac addresses But there is a limitation for these static Mac addresses they are allowed to work on the assigned port only because they are static fixed on the assignment port If users want to delete an entry in the static Mac address table click Delete button of the entry and the static Mac address will be removed from the table About Port Security function You can configure Mac Security Configuration function for port access security with Mac address There are Accept and Reject modes for it Accept mode Only the static address can access network via the port Reject mode Only the static address cannot access network via the port 42 6 Mac Security Configuration MAC Security Configuration Era bake Static MAC Number Security Control 1 Staticmode with Acceptfunction Mew SI No Security X S
60. switch and users called supplicant in 802 1x after first identification The valid value is 0 65535 Quiet Timeout Period This is the quiet time value between the switch and the user before next authentication process when authentication fails Tx Timeout Period This is the timeout value for the identification request from the switch to users The request will be re tried until the Re authentication Max Count is met After that authentication fail message will be sent The valid value is 0 65535 Radius Server Configuration This is for configuration between switch and RADIUS server Port Authentication Configuration Port Status Authentication Mode ci ZEN Yes Auto x Yes ai E Zaue E Force Authorizad Force Authorizad w Op HW mi Si wl b Force Authorizead The Port Authentication Configuration is used to select the authentication mode for each port of the switch 1 Auto This is the normal 802 1x operation mode The authentication status authenticated or unauthenticated depends on the authentication result of port 2 Force Authorized This mode will force the port always being authentication successful in 802 1x process and the real authentication result will be ignored 3 Force Unauthorized This mode will force the port always being authentication fail in 802 1x process and the real authentication result will be ignored 4 None This mo
61. the Mac address to ARL table These Mac ID are called Static Mac address This switch supports static Mac address assignment The static Mac address assignment will also limit the Mac address could be used or rejected on the assigned port only with the port security configuration function For example assigning 00 c0 f6 11 22 33 to Port 5 will always keep this Mac ID alive on Port 5 but also limit this Mac address could work on Port 5 only or rejected from Port 5 depending on the setting of its port security mode Note About Static Mac Address Filter in port binding function There is a Mac Security Configuration function for port security mode If it is set to Accept mode only these static Mac addresses can access network through the assigned port The other Mac addresses will be forbidden for network access through that port This function can be used for port binding security application Please refer to Section 6 2 6 3 for the details of the Mac address filter in operation of the switch 7 IEEE 802 1x Port Security Function If the 802 1x function is enabled the switch will act as an authenticator for users accessing network through the switch It will need a RADIUS server for the authentication function Users will be asked for username and password before network access If the RADIUS server authenticates it the switch will 8 enable the port for network access This function is very useful for network security applicat
62. tocol setting Show GVRP Protocol Status Show 802 1q VLAN Configuratuin Show 802 1x Protocol Status security Show MAC Security Configuration ratecontrol Show Rate Control Configuration stormcontrol Show Storm Control Configuration 10 1 show and show help commands will show the sub command list 10 2 show arl command will show static Mac ID setting in ARL table For example gt show arl Item Port Mac Address 1 5 00 C0 F6 1 1 22 33 10 3 show dynamic command will show current Mac address table content of the switch For example gt show dynamic Dynamic Adress Learning Table Item Port Mac Address VID The extra port is the interface to internal CPU 10 4 show cfg command will show Model Name Mac ID of the switch and Firmware version For example gt show cfg System Configuration Company Name Model Name Intellignet Switch MAC Address 00 C0 F6 FF 0D 01 Firmware Version 2 08 02 lt Dec 4 2003 17 27 16 gt 10 5 show net command will show current IP address configuration of the switch For example gt show net ethO Network Configuration DHCP ENABLE 27 IP Address 192 168 1 5 Netmask 255 255 255 0 Gateway 192 168 1 120 10 6 show igmp command will show current IGMP snooping function enable disable status and the IP multicast groups that learned by the switch For example gt sh igmp IGMP Configuration IGMP Switch Enabled Total Groups 3 Group 1 IP Add
63. ty the device with the lowest MAC address will then become the root device 20 hello 0 65535 the period to send the spanning tree maintenance packet if the switch is the root of the spanning tree Default is 2 seconds age 6 40 the spanning tree aging time if no spanning tree maintenance packet is received It will cause the spanning tree to re create Default is 20 seconds delay 4 30 the maximum waiting time before changing states i e listening to learning to forwarding This delay is required because every device must receive information about topology changes before it starts to forward frames In addition each port needs time to listen for conflicting information that would make it return to a blocking state otherwise temporary data loops might result d set sta port command is used to configure for ports of the switch Its syntax is gt set sta port 1 Syntax set sta port port arg_1 data_1 arg_1 data_1 arg_n data_n Argument List priority Set port priority COST Set port path cost priority 0 255 If the path cost for all ports on a switch are the same the port with the highest priority lowest value will be forwarded when looping happens If more than one port have the same highest priority the port with lowest port number will be forwarded cost 1 65535 It is used to determine the best path between devices if looping happens Lower values will be forwarded and should be ass
64. ty function status for each port 10 11 show snmp command will show SNMP configuration of the switch For example gt show snmp SNMP Configuration System Name Switch Location dis Contact name Jack Get Community public Set Community private 29 Trap Community 1 public Trap IP 1 0 0 0 0 Trap Community 2 public Trap IP 2 0 0 0 0 Trap Community 3 public Trap IP 3 0 0 0 0 Trap Community 4 public Trap IP 4 0 0 0 0 Trap Community 5 public Trap IP 5 0 0 0 0 10 12 show trunk command will show trunk configuration of the switch For example gt show trunk Trunk Group Setting Trunk Setting Enabled TRUNK Port List 10 13 show sta command will show spanning tree configuration of the switch For example gt show sta Spanning Tree Configuration SPT Setting Disabled Bridge Priority 32768 Bridge Hello Time 2 Bridge Max Age 20 Bridge Forward Delay 15 Port Priority 1 128 2 128 3 128 4 128 5 128 6 128 7 128 8 128 Port Path Cost 1 19 2 19 309 4 19 509 6 19 7 19 Gig It shows the Bridge and Port spanning tree configuration 10 14 show http command will show http enable disable state For example gt show http HTTP Protocol Setting HTTP Setting Enabled 10 15 show gvrp command will show the GVRP function status for 802 1Q VLAN operation For example gt show gvrp GVRP Protocol Disable 10 16 show 1qvlan command will show current 802 1Q VL
65. utton E System Upgrade Enter the path and name of the upgrade file then click the START button TC START Four functions are supported as the system maintenance tools a System Backup Backup Setting will backup the configuration of the switch to the web management PC Restore Setting will get the configuration backup file from the web management PC and restore it to the switch b System Restore Factory Default Setting This function will restore the switch configuration to factory default setting c System Reset This function will cause the switch reset d System Upgrade This function will upgrade the system operation software from the web management PC 59 6 4 About Telnet Interface If you want to use Telnet to management the switch from remote site you have to set the IP Mask Gateway address to the switch first from console Then use telnet lt IP gt command in DOS Its operation interface is the same as console interface 6 5 About SNMP Interface If you want to use NMS to management the switch from remote site you have to set the IP Mask Gateway address to the switch and configure the SNMP setting of the switch from console first Then you can use SNMP management program to manage this switch This switch supports SNMP Version 1 agent function and MIB II Interface Bridge MIB Etherlike MIB and Private MIB The default GET community name is public and SET community name
66. xample gt show port Port Configuration 28 Port Name Status Disable Auto Speed Duplex Flow Control 1 10 100Mbase T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF 10 100M base T DOWN NO ON 10 Half OFF ONOaAARWDPD 10 10 show qos command will show QoS configuration of the switch For example gt sh qos QoS Configuration Qos setting Disabled 802 1p Priority Tag 7 gt P3 802 1p Priority Tag 6 gt P3 802 1p Priority Tag 5 gt P2 802 1p Priority Tag 5 gt P2 802 1p Priority Tag 3 gt P1 802 1p Priority Tag 2 gt P1 802 1p Priority Tag 1 gt PO 802 1p Priority Tag 0 gt PO Port Priority Port Priority Port Priority Port Priority 1 Low 2 Low 3 Low 4 Low 5 Low 6 Low 7 Low 8 Low Port FlowCtrl Port FlowCtrl Port FlowCtrl Port FlowCtrl 1 OFF 2 OFF 3 OFF 4 OFF 5 OFF 6 OFF 7 OFF 8 OFF Port 802 1p Port 802 1p Port 802 1p Port 802 1p 1 OFF 2 OFF 3 OFF 4 OFF 5 OFF 6 OFF 7 OFF 8 OFF The first part is the mapping of 802 1P priority values O0 7 to the four priority queues of the switch The second part is the port based priority setting The third part is the flow control setting for each port when congestion happens The fourth part is the 802 1P priori

53 , USER`S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents