Quick Setup Guide - Devon Medical Products
Contents
1. DEVON MEDICAL PRODUCTS ArterioFlow 7500 Quick Setup Guide www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 LB05 0003 Rev B 20140314 DEVON MEDICAL PRODUCTS setup H Therapy Setup H TABLE OF CONTENTS Customer Set P Treatment www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 DEVON MEDICAL PRODUCTS SETUP Open the shipping box and lift device up and Out of box 7 Check to make sure the box also contains 1 POWER CORD 1 AIR BLOCKER and a USER MANUAL E Remove the protective foam covers on each side and the plastic bag Not Pictured l Place the device on a flat and stable surface near the patient Ik Unwrap the POWER CORD from the box and plug it into the back of the machine Plug the device into a safe and properly grounded outlet www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 DEVON MEDICAL PRODUCTS TH E RA PY S ETU P Settings can only be modified or restored before or in between treatments There are two operating modes with this device e Factory Default Device comes with a factory default setting providing a compression pressure at 120mmhg with a one second delay between the foot and calf 20 second cycle time 30 minute treatment time e Customer Set his mode allows you to set2. Pressure can range from 25 125 mmHg increments of 1 mmHg E 2 rime 4 Push the SHUTTLE KNOB to confirm the new Pressure Access the second parameter Treatment Time by turning the SHUTTLE KNOB to the right Push the SHUTTLE KNOB to select Treatment Time www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 DEVON MEDICAL PRODUCTS CUSTOMER SET Increase the Treatment Time by turning the SHUTTLE KNOB to the right decrease Treatment Time by turning to the left Treatment time can range from 5 180 minutes increments of 5 minutes 18 Push the SHUTTLE KNOB to confirm the new Treatment Time ds at ui zi 1t T me i lt 46 Min 2 0 Access the third parameter Cycle Time by turning SHUTTLE KNOB to the right Push the SHUTTLE KNOB to select Cycle Time N Increase the Cycle Time by turning the SHUTTLE KNOB to the right decrease Cycle Time by turning to the left Cycle Time can range from 15 30 seconds increments of 1 second Push the SHUTTLE KNOB to confirm the new Cycle Time To exit and complete turn the SHUTTLE KNOB to the right Push to select to EXIT 23 You will be taken to the start display Push E at HE the green START button to start your custom Le TE H E Hb Treatment 06 www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 DEVON MEDICAL PRODUCTS TREAT
3. MENT l The pump has a 4 second prefill stage before it starts therapy Not Pictured h Each Treatment will end after its set Treatment Time has elapsed The user can also end the Treatment at any time during a Treatment session by pressing the STOP button on the front panel Note l the user presses STOP the Treatment will not pick up from where it left off at Hf The device will vacuum air from the garment for 3 seconds so that it will be easy to take off Not Pictured 7 Once the sleeve is deflated press the POWER SWITCH down on the backboard to the OFF position and then unplug the POWER CORD 28 Once the power indicator light is off it is safe to remove the garment Not Pictured 29 The garment should be loose enough now that you can unzip the garment and remove Not Pictured www devonmedicalproducts com 1100First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 DEVON MEDICAL PRODUCTS
4. your Pressure Treatment Time and Cycle Time Attach the QUICK CONNECTORS of the garment to the QUICK CONNECT PORTS which are located on the front panel of the device N Putting the garment on 1 Put the arch of the foot over the inflation area than snugly secure the VELCRO STRAPS over the bridge of the foot 2 Wrap the two VELCRO STRAPS snugly around the calf If Press Main POWER SWITCH up to ON position which is located on the rear panel The green power indicator on the front panel will then illuminate FACTORY DEFAULT Upon this display User can directly push START to run the device on Factory Default m www devonmedicalproducts com 1100 First Avenue Suite 202 King of Prussia PA 19406 866 446 0092 10 I 12 l 14 DEVON MEDICAL PRODUCTS CUSTOMER SET Upon this display User can access Customer Set Mode by pushing the SHUTTLE KNOB that will take you to Therapy Mode Setting the indicator light will be yellow setting This display shows Therapy Mode Setting gt E arc t aru D F Au l ty Customer Set Turn the SHUTTLE KNOB to the right to select Customer Set Then push the SHUTTLE KNOB to access all parameters Factory Default Customer Set This display shows the first parameter Pressure Push the SHUTTLE KNOB to select Pressure Increase the Pressure by turning the SHUTTLE KNOB to the right decrease the Pressure Dy turning to the left
Download Pdf Manuals
Related Search