Wireless Flash Trigger Product Manual
Contents
1. any shooting opportunity Fire the flashgun through hot shoe part and fire the studio light through PC socket Can control multiple flashguns and studio lights at the same time Shutter function includes single continuous bulb and 4 second delay shooting Can control multiple cameras for shooting at the same time Maximum distance up to 80 meters Extra low standbv power consumption Transmitter Standbv Time 10000 hours Receiver Standbv Time up to 300 hours Low Voltage Design allow using rechargeable batteries Items Included Please check the listed items below in the package and contact your dealer if there is any missing Transmitter Receiver AAA Lithium Battery CR 2032 Battery inside the Transmitter 2 5mm 3 5 connecting cable 2 5mmt 6 35 connecting cable User Manual Receiver Holding Mount Hot Shoe Protection Shutter Control Cable either one For Canon 2pcs For Nikon 2pcs For Sony 1pc For Olympus Panasonic 3pcs Specifications FSK2 4GHz Wireless System Distance Transmitter 10000 hours for CR 2032 Lithium Standby Time Battery noli iemeloj 400 hours for AAA Batterv Dimensions Transmitter 65 5mm x 39mm x 28mm HxWxD Receiver 81mm x 38 5mm x 29 5mm Transmitter 32 5g with Battery Weight ke Receiver 60 5g with Batterv Basic Operation Batterv Installation and Replacement Transmitter Please follow the steps to install and replace the batter2. not immerse in water or exposed to rain as this may lead to failure of the device Do not store under high temperature such as a covered car under direct sunlight the dashboard and other high temperature places Do not use near flammable areas Failure to follow this warning may cause fire or explosion This product includes batteries please strictly follow the instruction for proper operation Failure to follow this may cause explosions fire or personal injury Light Indicator Shutter Release Button Function Light Indicator Power Switch Setting Button Batterv Compartment Cover Channel Switch CR 2032 Lithium Batterv Locking Screw Hot Shoe Part Connecting Pins Pawn TX Light Indicator Power Switch Sticker Hot Shoe Part Input output socket Battery Compartment Cover Channel switch Hot Shoe Nut Locking Screw Pawn RX Light Indicator Device power communication and output status indication The indicator shows green when half press the shutter release button and red when full press Shutter Release Button Half press means the camera is auto focusing and full press means shooting Function Light Indicator When use as shutter remote function indicator lights show the shooting mode under setting press the switch to change the modes Single BULB delav PS Make sure the shooting mode on both the camera and the transmitter is the same to work efficientiv P
3. Ok Scie Pawn Wireless Flash Trigger Product Manual Overview Thank vou for purchasing high performance Pixel product Pawn Its feature include flashgun trigger studio light trigger and wireless shutter control The flash sync speed is up to 1 250s The shutter control mode included single continuous BULB and 4sec delay shooting Pawn is using global free channel 2 4GHz and FSK modulation system to make the performance more stable Unique power saving design makes the battery life of the transmitter and receiver last longer Before using this product you must read carefully and understand the user manual Be familiar with the use of your camera and flashgun so as to ensure you can operate the Pawn correctly 1 Make sure the camera and flash are powered off before installing the Pawn 2 As this is an accessory of electronic product may be due to external environment matters the camera or flashgun cannot be made or lead to normal operation However the possibility is very low 10 When connecting the cable with the device do not pull directiv on the wires Drops or shocks will lead to product failure The batteries should be installed correctly Reverse polarity may cause batteries to leak corrosive liquids heat or explosion When notin use for long durations please turn off the transmitter s and the receiver s power and remove the battery Keep dry and do not touch the product with wet hands Do
4. ill released or fully pressed 4 Fully press the TX shutter release button for sending out shooting signals TX red light on and flashes but RX red light on and blinks The Camera starts to count time 5 RX indicator light turns off and sends out shooting signals to the Camera after finishing counting ik When the focusing mode set as M the camera will not focus when half pressing the button When the camera focusing mode is set as A most cameras when out of focusing will not shoot even thev get the shooting signal Thank vou for purchasing PIXEL product and read this instruction manual carefuliv If vou have anv question please kindly contact our local dealer or visit http www pixelhk com This instruction manual is updated on 1st October 2011 Please contact the PIXEL seller to get the information if you want to use this product together with other latest product which published after this date Pile 7 G PSM38 V20 02
5. nction 1 Press SET button of transmitter slightly and choose the mode asICJ I 2 Set the camera function mode as OO 3 Half press the shutter release button for sending out the focus signal The light indicator of the transmitter and receiver will show green Camera is under focus state until the button is released or fullv pressed 4 Full press the shutter release button to send out the shooting signal The light indicator of the transmitter and receiver will show red Camera is starting to shoot Continuous shoot or BULB shoot function 1 Press the TX setting button and setitas B 2 Set the Camera shooting mode as Jor BULB 3 Half press the TX shutter release button for sending out focus signals both TX and RX green indicator lights are on The Camera is under focus state till released or fully pressed 4 TX sends out shooting signals while fully pressed At the moment TX red light on and flashes but RX red light on and blinks The Camera starts to shoot 5 Repress the RX release button TX stops sending out signals and RX stops sending out shooting signals then the Camera stops shooting Delay shoot function 1 Press SET button of transmitter and set the function as 2 Set the Camera shooting mode as 0 3 Half press the TX shutter release button for sending out focus signals both TX and RX green indicator lights are on The Camera is under focus state t
6. oal for shooting vou can set the transmitter with different function 1 Press SET of transmitter the function indicator lights up and shows the current function mode 2 Press SET again another function indicator lights up and this mode is the working mode 3 Select current function mode if necessary 4 The function indicator light will turn off after 4sec and the transmitter will stay in the mode as your last selected function When the function indicator is turned off vou can check the current mode bv pressing SET slightiv Fire theflashgun 1 Check if all connections are completed See if all the power is turned on and the flashgun s parameter is set 2 Half press the camera shutter release transmitter then send out the signal and wake up the sleeping flashgun Flash in Standbv mode 3 Fully press the camera shutter release transmitter then send out flash signal and trigger the flashgun to sync flashing ik When using the transmitter which is not compatible to Camera models you need to half press the shutter button of transmitter once the camera can sync shooting within one minute You ll need to half press the transmitter button again if time exceeds Xi Some of the flash wake up time may take longer we suggest to half pressing the button for little bit longer then fully press the button to shoot Try to avoid fully press the buton till the end Control camera shooting Single shoot fu
7. ower Setting Switch Press the switch on transmitter 2 seconds to turn on the device meanwhile the function indicator lights up showing the current function mode press the switch again to change the unction mode Channel Setting There are totally 16 channels and the channel switch is inside the battery compartment After setting channel please double check that the transmitter and its receiver s are in the same channel When using multi sets Pawn in the same area please change each sets to different channels PS When you get any frequency jamming please change the channel Receiver Power Switch Switch to OFF to turn off the device switch to ON to turn on the device Input output socket 1 When use to trigger studio light plug studio light connecting cable 2 5mm side into the socket and the other side into studio light side 2 When use as shutter remote controller plug shutter connecting cable 3 5mm side into the receiver socket and the other side into camera shutter release socket Batterv Compartment Loading two AAA batteries Receiver s Hot Shoe Nut for Tripod or other mounting nut Transmitter Mounting Foot Input interface connection with camera hot shoe Sticker Showing product S N number batterv tvpe on the sticker Features Using global free 2 4GHz channel and FSK modulation svstem 16 selectable channels Flash sync speed up to 1 250s With flashgun wake up function will not miss
8. v 1 Slide and open the batterv compartment cover 2 Please press the metal spring and take out the battery 3 When installation the positive of the battery must be faced outside Then put the battery compartment cover correctly Receiver Beware of the battery polarity when installing Wrong installation may cause the device cannot operate properly It may demage the device or cause property damage and personal injury Power Switch Transmitter 1 2 3 4 Receiver Pawn RX is using 2 steps power switch switch to OFF to turn off and switch to ON to turn on Transmitter is under the standby mode when install battery To turn on the power press Power Switch Setting Button for 2 seconds Function Light Indicator turns on and showing the existing group Function Light Indicator turns off after 4 seconds transmitter enters into standby mode Under the standby mode press Power Switch Setting Button for 2 seconds After red light blinks for several times the transmitter turns off Please turn off the transmitter when notin use ess Flash Trigger Channel Setting For proper operation same channel must be setfor the transmitter and receiver ON ON EG E sags 1 2 4 1 2 4 Transmitter Receiver Set the Transmitter Function When actas Wireless Remote Contr
Download Pdf Manuals
Related Search