Home

Manual - DFI Inc.

1. Chapter 3 When IDE mode is selected in the SATA Mode Selection it will display the following SATA Controller Speed information Indicates the maximum speed that the SATA controller can support Aptio Setup Utility Copyright C 2012 American Megatrends Inc Port O Port 1 Port 4 and Port 5 SATA Mode Selection Enables or disables the SATA port Hot Plug Designates the SATA port as hot pluggable Version 2 15 1236 Copyright C 2012 American Megatrends Inc When AHCI mode is selected in the SATA Mode Selection it will display the following information Aptio Setup Utility Copyright C 2012 American Megatrends Inc SATA Mode Selection Version 2 15 1236 Copyright C 2012 American Megatrends Inc 36 eee ee W J em ndi s Chapter 3 BIOS Setup www dfi com This section is used to configure the parameters of Management Engine Technology Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt Firmware Update Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc Firmware Update Configuration This field is used to configure the parameters of Management Engine Technology Aptio Setup Utility Copyright C 2012 American Megatrends Inc Me FW Image Re Flash Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc a This section is used to confi
2. HD620 H81 ATX Industrial Motherboard User s Manual A30130548 Copyright This publication contains information that is protected by copyright No part of it may be re produced in any form or by any means or used to make any transformation adaptation without the prior written permission from the copyright holders This publication is provided for informational purposes only The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifi cally disclaims any express or implied warranties of merchantability or fitness for any particular purpose The user will assume the entire risk of the use or the results of the use of this docu ment Further the manufacturer reserves the right to revise this publication and make changes to its contents at any time without obligation to notify any person or entity of such revisions or changes Changes after the publication s first release will be based on the product s revision The website will always provide the most updated information 2015 All Rights Reserved Trademarks Product names or trademarks appearing in this manual are for identification purpose only and are the properties of the respective owners FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reason ab
3. 8 Check the software you are installing Then click Continue Anyway to start the installation Hardware Update Wizard Select the device driver you want to install for this hardware P Install From Disk Insert the manufacturer s installation disk and then make sure that the correct drive is selected below Copy manufacturer s files from E Intel LAN for xp PRO1000 WinxP Related PC w Back Next gt Cancel For 32 bit the file name is e1d5132 inf Hardware Update Wizard Select the device driver you want to install for this hardware Q Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver you want to install click Have Disk Show compatible hardware Model j Intel R Ethernet Connection 121 7 LM This driver is not digitally signed Tell me why driver signing is important Commented Manapainean ac rast Upale Wirard Hardware miaa mn Tha zhan veu anm rrria lrag bor Hha hadaa lst hene Connection 2174 M has rcl peace Wickes Loge behing bo vark iz crap sei windavn F Tell ine sale this hoiira is boat 9 Click Finish to close the wizard 10 After completing the instal lation the Network adapters Intel R Ethernet Connection 1217LM will appear on the computer management list Chapter 4 Hardware Update Wizard Completing the Hardware Up
4. 3 Verify that the attached serial device works by attaching it to a serial port that is working and configured correctly If the serial device does not work either the cable or the serial device has a problem If the serial device works the problem may be due to the onboard I O or the address setting 4 Make sure the COM settings and I O address are configured correctly Keyboard Nothing happens when a key on the keyboard was pressed l Make sure the keyboard is properly connected 2 Make sure there are no objects resting on the keyboard and that no keys are pressed dur ing the booting process Appendix C Troubleshooting Checklist www dfi com
5. 6M Cache up to 3 6 GHz 65W i5 4570TE 4M Cache up to 3 3 GHz 35W i3 4360 4M Cache 3 7 GHz 54W i3 4350T 4M Cache 3 1 GHz 35W i3 4340TE 4M Cache 2 6 GHz 35W Intel Core i3 4330 4M Cache 3 5 GHz 54W Intel Core i3 4330TE AM Cache 2 4 GHz 35W Intel Pentium G3420 3M Cache 3 2 GHz 53W Intel Pentium G3320TE 3M Cache 2 3 GHz 35W Intel Celeron G1820 2M Cache 2 7 GHz 53W Intel Celeron G1820TE 2M Cache 2 2 GHz 35W e 22nm process technology e Intel H81 Express Chipset NCT6102 4Eh HD620 H81B D NCT6106 4Eh HD620 H81X Two 240 pin DDR3 DI MM sockets e Supports DDR3 1333 1600MHz e Supports dual channel memory interface e Supports up to 16GB system memory DRAM device technologies 1Gb 2Gb and 4Gb DDR3 DRAM technologies are supported for x8 and x16 devices unbuffered non ECC e 1 PCIe x16 Gen 3 slot PCI e 3 0 e 1 PCIe x4 Gen 2 slot PCI e 2 0 X1 signal 4 PCI slots PCI 2 3 1 shared with I SA slot e 2 ISA slots e Intel HD Graphics Display ports VGA and DVI D e VGA and DVI D support up to 1920x1200 60HZ resolution e Supports 6 Graphics Execution Units EUs e Intel Clear Video Technology DirectX Video Acceleration DXVA support for accelerating video processing Realtek ALC886 5 1 channel High Definition Audio e Audio outputs Mic in Center Subwoofer Line in Surround and Line out e S PDIF audio interface e Inte
6. Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note If you are an Original Equipment Manufacturer OEM Independent Hardware vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies Back 3 Go through the readme Intel Graphics Media Accelerator Driver document for system require z ments and installation tips then AAE eE EE TE m Blah 1 12 intel click Next Readme File Information Refer to the Readme file below to view the system requirements and installation information Cet o s n n o n o s o s o o s o o HT s HTT s S o S n TAKE s s n m s s sts a wo 8t 4 A n n E Production Version Releases Microsoft Windows 2000 Microsoft Windows XP i si x Back Cancel Intel Installation Framework 4 Setup is now installing the Intel Graphics Media Accelerator Driver driver Click Next to continue WS e AS I Intelh Graphics Media Accelerator Driver Setup Progress Please pet nhie the nlcwing setup operations are perfomed copying F F s C CiProgram F Fiesi inbe inten Graphics Meda Acceler ator Crh lunra aE Copying F s Cilprogeam Pileslinbel intelR
7. MOV DX AFH MOV AL 10H Set watchdog timer value OUT DX AL MOV DX 4EH MOV AL FOH Select watchdog Control Register OUT DX AL MOV DX AFH MOV AL O2H Set Watchdog Control Value OUT DX AL MOV DX AEH MOV AL AAH OUT DX AL Appendix A Watchdog Sample Code www dfi com Appendix B System Error Message When the BIOS encounters an error that requires the user to correct something either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message PRESS F1 TO CONTINUE CTRL ALT ESC or DEL TO ENTER SETUP will be shown in the information box at the bottom Enter Setup to correct the error Error Messages One or more of the following messages may be displayed if the BI OS detects an error during the POST This list indicates the error messages for all Awards BI OSes CMOS BATTERY HAS FAI LED The CMOS battery is no longer functional It should be replaced I mportant ik Danger of explosion if battery incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries accord ing to the battery manufacturer s instructions CMOS CHECKSUM ERROR Checksum of CMOS is incorrect This can indicate that CMOS has become corrupt This error may have been caused by a weak battery Check the battery and replace if necessary DISPLAY SWITCH IS SET INCORRECTLY The display switch on the motherboard can be set to either
8. will appear If after inserting the CD Autorun did not automatically start which is the Mainboard Utility CD screen did not appear please go directly to the root directory of the CD and double click Setup For Windows 8 Intel Chipset Software Installation Utility Intel HD Graphics Drivers Intel Management Engine Drivers Intel Rapid Storage Technology Intel Rapid Start Technology F6 Floppy al Infineon TPM Drivers and Tool option E Infineon TPM Drivers and Tool option Adobe Acrobat Reader 9 3 More gt gt Exit Chapter 4 Supported Software www dfi com For Windows XP System Utility System Utility Chapter 4 Microsoft Framework 3 5 Intel Chipset Software Installation Utility Microsoft DirectX 9 00 Intel HD Graphics Drivers Intel Management Engine Drivers Audio Drivers Intel LAN Drivers DFI Utility Infineon TPM driver and tool option Adobe Acrobat Reader 9 3 More gt gt Exit User s Manual Readme Browse the CD lt lt Previous Microsoft NET Framework 3 5 For Windows XP Note LET Before installing Microsoft NET Framework 3 5 make sure you have updated your Windows XP operating system to Service Pack 3 To install the driver click Microsoft NET Framework 3 5 on the main menu 1 Read the license agreement care E Microsoft MET Framework 3 5 Setup fully aaa Welcome to Setup MET Framework Click I have read and accept j Ba gu
9. 8 15 10 2639 Win32 OpenCL OCLSetup exe Click Next to continue 4 m M Intel Installation Framework Um intel You must restart this computer for the changes to take effect Would you like to restart the computer now arent EE caoine a aio Intel HD Graphics Driver Setup Is Complete Yes I want to restart this computer now No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Chapter 4 Supported Software www dfi com Chapter 4 I ntel Management Engine Drivers To install the driver click Intel Management Engine Drivers on the main menu l Setup is ready to install the driver Click Next Intel Management Engine Components l intel Welcome to the Setup Program This setup program will install the Intel Management Engine Components Itis strongly recommended that you exit all programs before continuing Click Next to continue Install Intel Control Center Intel Control Center provides a centralized starting point for Intel applications making it easier to find the programs that you need 2 Read the license agreement then click Yes Intel Management Engine Components License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM
10. ACPI Power Management Configuration submenu of the BIOS Refer to the chapter 3 for more informa tion I mportant The 45V standby power source of your power supply must support 2720mA www dfi com COM Serial Ports RS232 COM 6 COM 5 COM 3 COM 4 COM 1 COM 1 COM 2 RS232 422 485 COM 9 COM 10 9 RS232 232 a COM 3 to COM 10 are fixed at RS232 The pin functions of COM 1 and COM 2 will vary according to jumpers setting JP2 JP17 and JP18 are used to configure the Serial COM port 1 JP16 JP19 and JP20 are used to configure the Serial COM port 2 JP14 for COM 1 and JP15 for COM 2 are used to configure Se rial COM ports to pure RS232 or RS232 with power Refer to COM 1 COM 2 RS232 422 485 Select and COM 1 COM 2 RS232 Power Select in this chapter for more information The serial ports are asynchronous communication ports with 16C550A compatible UARTs that can be used with modems serial printers remote display terminals and other serial devices Chapter 2 Hardware Installation COM 3 to COM 6 Connecting External Serial Ports Your COM port may come mounted on a card edge bracket Install the card edge bracket to an available slot at the rear of the system chassis then insert the serial port cable to the COM connector Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM connector BI OS Setting Configure the serial COM ports in the Advanced men
11. ANANDE WG82574L DDR3_1 Power LED B PCle x1 DDR3 2 DDR3 2 Realtek C886 PERE PEPPER EE EEE SATA1 supports SATA DOM SPI a m IIIII IEEE uuu 2 d SATA 3 0 Standby 1 OED S PDIF i 2 t Power LED 1 9 Front Audio III PEPER EEE EEE ERR ERREUR ITE Clear CMOS he ee Data J P9 ITE HIIIII BERNER IT8893E Qa x Rear I O PCI 3 1 200 11111111 EFTEETETETETEETEEEETEEEETIEETTRITIIHI SATA DOM Power USB 2 3 6 7 Power a XX 02777 E a a a a 2 ED EEERHRRRERRRRRERRERRRERRRRRERRERREREERNIUII IN Battery wi ig jiem n Select Toe State Onboard l O iDIO 11 13 15 17 i LAN2 State Output State JP7 4 LANI State S iDIO 3 5 7 9 IIIII PEEP EE PEEP 1 1 ats Output State J P12 IS ae ITE torage DIO Power Select III 5IIIIEIEIEIEIEIEIEIINEINININININININININININININININININININININII 1 P13 i u Bue E H NES oo Panel Nuvoton 10 2 LPC Debug NCT5104D USB 10 11 11l Xpansion 2 10 2 10 MELLE oa 1 0 9 mum mmm BEHENENEHEHEEHEHEEHEEHEEHEHEHEEEEHEEEEHEHEEHEEHEHHEEEEEHEEHEENS 1 9 1 9 COM9 COM10 BH H H H EH EH NH NH E NH NH NH OH HON H E HON HON HON HON RPP eee ENEBEHBHBEEEEENEEENENSNSIS Features e Two 240 pin DDR3 DIMM sockets e HD620 H81B LANI only e HD620 H81X 10 COM COMI to COM10 s Supports DDR3 1333 1600MHz T PDOA PRIB Oe COM OME and CONA Supports dual channel memory interface Supports up to 16GB system memory Chapter 2 Hardware Installati
12. DVD CD ROM drives Local Users and Groups ig dig Human interface Devices Performance Loge arid Abert Gy IDE ATAJATAPI controllers BA Device Manager 3 Sterage Removatle Storage ed Processors H 3 Sound video and game controlers System devices 2 Click Yes want to restart my computer now then click Finish Restarting the system will allow the new software installation to take effect 2 Choose Install from a list or TAs specific location Advanced and click Next to continue the installation This wizard helps you install software for Ethernet Controller g If your hardware came with an installation CD or floppy disk insert it now What do you want the wizard to do O Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Chapter 4 Supported Software www dfi com 3 Choose the option Don t search will choose the driver to install in order to select the device driver from a list and click Next 4 Select a hardware type DVD CD ROM drives Then click Next 5 Select your hardware disk and then click Have Disk Chapter 4 Supported Software www dfi com Chapter 4 Hardware Update Wizard Please choose your search and installation options Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes
13. JP18 JP2 JP16 3 4 On RS422 Full Duplex 1 2 On RS232 default e e o o ooo ooo NBO e W Ul o o o oo ooo o JP19 JP20 COM 1 COM 1 COM 2 RS232 422 485 RS422 6 5 4 3 2 1 1 3 2 4 On RS232 default 3 5 4 6 On RS422 Full Duplex RS485 These jumpers allow you to configure the Serial COM ports to RS232 RS422 Full Duplex or RS485 JP2 JP17 and JP18 are used to configure the Serial COM port 1 JP16 JP19 and JP20 LE are used to configure the Serial COM port 2 The pin functions of Serial COM ports 1 and 2 will vary according to these jumpers setting Note When COM 1 RS232 422 485 is selected JP17 and JP18 must be set in accordance to JP2 And when COM 2 RS232 422 485 is selected JP19 and JP20 must be set in accordante to JP16 Chapter 2 Hardware Installation www dfi com COM 1 COM 2 RS232 Power Select SATA DOM Power Select 246 246 135 135 1 3 RD 2 4 DCD On 3 5 5V 4 6 12V On RS232 default RS232 with power l7 3 1 2 On GND SATA 1 default JP11 123 2 3 On 5V JP11 is used to select the power of SATA DOM Note SATA port 1 provides adequate space for SATA DOM JP14 for COM 1 and JP15 for COM 2 are used to configure Serial COM ports to pure RS232 or RS232 with power Chapter 2 Hardware Installation www dfi com Digital O Power Select Digital 1 O Output State 3 P 1 1 2 On 45V standby d
14. Make sure to find the proper orientation before plugging the connectors The system board requires a minimum of 300 Watt power supply to operate Your system configuration CPU power amount of memory add in cards peripherals etc may exceed the minimum power requirement To ensure that adequate power is provided we strongly recom mend that you use a minimum of 400 Watt or greater power supply I mportant X Insufficient power supplied to the system may result in instability or the add in boards and peripherals not functioning properly Calculating the system s approximate power usage is important to ensure that the power supply meets the system s consumption requirements www dfi com Chassis I ntrusion Connector Front Panel Connector Chassis 1 Intrusion Signal H os 2 HDD LED PWR LED RESET SW i ATX SW HDD LED HDD LED 1112 This LED will light when the hard drive is being accessed RESET SW Reset Switch The board supports the chassis intrusion detection function Connect the chassis intrusion This switch allows you to reboot without having to power off the system sensor cable from the chassis to this connector When the system s power is on and a chassis intrusion occurred an alarm will sound When the system s power is off and a chassis intrusion ATX SW ATX Power Switch occurred the alarm will sound only when the system restarts This switch is used to power on or
15. SCETIARELICEIEIE ACTEM b Intel Installation Framework Chapter 4 Go through the readme document for system re quirements and installation tips then click Next Setup is now installing the driver Click Next to con tinue Click Yes want to restart this computer now then dick Finish Restarting the system will allow the new software installation to take effect E icu CR ERG CEN ERN os Intel HD Graphics Driver Readme File Information Refer to the Readme file below to view the system requirements and installation information Production Version Releases Microsoft Windows 7 Microsoft Windows Embedded Standard 7 1 1 These operating systems supported for embedded designs and usage Driver Revision 15 26 3 2639 February 8 2012 Intel Installation Framework Intel R HD j Graphies Driver intel Setup Progress Please wait while the following setup operations are performed Creating Registry Key HKLM SOFTWARE Microsoft Windows Media Foundation HardwareMFT 4 Creating Registry Key HKLM SOFTWARE Microsoft Windows Media Foundation HardwareMFT Creating Registry Key HKLM SOFTWARE MicrosoftlWindows Media Foundation HardwareMFT Registering DLL C Program Files Common Files Intel Media SDK j2 3 0 mfx_mft_h264vd_32 1 Registering DLL C Program Files Common Files Intel Media SDKV23 O nfx_s mft h264ve 324 tch hw32 s1 1 Creating Process E Graphices WIN7
16. a CPU fan with heat sink Without sufficient air circula the arrow shown on top of tion across the CPU and heat sink the CPU will overheat damaging both the CPU and system the pin XN bh z board b Fi Push down two pushpins m that are diagonally across Il i Il WII 2a A lh li LE A boxed Intel processor already includes the CPU fan and heat sink assembly If your d oq nm E wl EUS CPU was purchased separately make sure to only use Intel certified fan and heat other two push pins j WT sink 1 Before you install the fan heat sink you must apply a thermal paste onto the top of the CPU The thermal paste is usually supplied when you purchase the fan heat sink assem bly Do not spread the paste all over the surface When you later place the heat sink on top of the CPU the compound will disperse evenly Unlocked position Some heat sinks come with a patch of pre applied thermal paste Do not apply thermal AE of push pin paste if the fan heat sink already has a patch of thermal paste on its underside Peel the m strip that covers the paste before you place the fan heat sink on top of the CPU San of 2 Place the heat sink on top of the CPU The 4 push pins around the heat sink which are used to secure the heat sink onto the sys tem board must match the 4 mounting holes around the socket CPU Fan connector 5 Connect the CPU fan s cable to the CPU fan connector
17. add in boards and other components Perform installation procedures at an ESD workstation only If such a station is not available you can provide some ESD protection by wear ing an antistatic wrist strap and attaching it to a metal part of the system chassis If a wrist strap is unavailable establish and maintain contact with the system chassis PS 2 KB MS Power Select i JP1 e USB 8 9 Power Select TP 7 T TCU throughout any procedures requiring ESD protection 1 P2 i UPL COM1 RS232 422 485 Select i P17 i Iura BOSS x CPU an x EEEEEEEEEEEEBI mam NETTES JP18 j EC 1 25 NCT6106D i 1 Pi6 i 1CED Eng o s105820 Parallel COM2 RS232 422 485 Select JP19 12V S ste Me o O KLAO Power ystem mory COMI RS232 Power Select _ JP14 EB MEME ME COM2 RS232 Power Select JP15 1 4 min Bosse CERERI ee IUE Chassis 1 91 9 intrusion 8 C optional 2 102 10 I mportant When the Standby Power LED lights red it indicates that there is power on the system board Power off the PC then unplug the power cord prior to installing any de vices Failure to do so will cause severe damage to the motherboard and components AS Media ASM1442 Buzzer 1 9 1 9 COM4 COM3 USB 0 1 Power if Select J P5 USB 0 1 Intel wma WGI217LM USB 2n A USB 4 5 Power Select J P6 Select J P10 1CED p Intel EH E Standby DDR3 1 Mic i
18. monochrome or color This indi cates the switch is set to a different setting than indicated in Setup Determine which setting is correct either turn off the system and change the jumper or enter Setup and change the VIDEO selection FLOPPY DISK S fail 80 Unable to reset floppy subsystem FLOPPY DISK S fail 40 Floppy type mismatch Hard Disk s fail 80 HDD reset failed Hard Disk s fail 40 HDD controller diagnostics failed Appendix B Hard Disk s fail 20 HDD initialization error Hard Disk s fail 10 Unable to recalibrate fixed disk Hard Disk s fail 08 Sector Verify failed Keyboard is locked out Unlock the key The BIOS detects that the keyboard is locked Keyboard controller is pulled low Keyboard error or no keyboard present Cannot initialize the keyboard Make sure the keyboard is attached correctly and no keys are being pressed during the boot Manufacturing POST loop System will repeat POST procedure infinitely while the keyboard controller is pull low This is also used for the M B burn in test at the factory BI OS ROM checksum error System halted The checksum of ROM address FOOOOH FFFFFH is bad Memory test fail The BI OS reports mernory test fail if the memory has error s Appendix B System Error Message www dfi com Appendix C Troubleshooting Checklist Troubleshooting Checklist This chapter of the manual is designed to help you with problems t
19. off the system PWR LED Power Standby LED When the system s power is on this LED will light When the system is in the S1 POS Power On Suspend state it will blink every second When the system is in the S3 STR Suspend To RAM state it will blink every 4 seconds Pin Pin Assignment Pin Pin Assignment 3 HDD Power 2 LED Power HDI Eee 5 Signal PWR LED 4 LED Power 7 Ground 6 Signal RESET SW 9 RST Signal 8 Ground ATX SW 11 NC 10 Signal 27 Chapter 2 Hardware Installation www dfi com Standby Power LED Standby Power LED 0 mm T 3 zi po M o mm m es EN This LED will lit red when the system is in the standby mode It indicates that there is power on the system board Power off the PC and then unplug the power cord prior to installing any devices Failure to do so will cause severe damage to the motherboard and components Chapter 2 Hardware Installation Expansion Slots PCI Express x16 PCI PCI Express x4 x1 Signal PCI E CNET PCI gt FEEEE CERE PCI C B um E ISA ISA mmm m PCI Express x16 Slot Install PCI Express x16 graphics card that comply to the PCI Express specifications into the PCI Express x16 slot To install a graphics card into the x16 slot align the graphics card above the slot then press it down firmly until it is completely seated in the slot The retaining clip of the slot will automatically hold the graphics card in place PCI Slot The
20. s Manual on the main menu Warranty 1 Warranty does not cover damages or failures that arised from misuse of the product inability to use the product unauthorized replacement or alteration of components and product specifications 2 The warranty is void if the product has been subjected to physical abuse improper instal lation modification accidents or unauthorized repair of the product 3 Unless otherwise instructed in this user s manual the user may not under any circum stances attempt to perform service adjustments or repairs on the product whether in or out of warranty It must be returned to the purchase point factory or authorized service agency for all such work 4 We will not be liable for any indirect special incidental or consequencial damages to the product that has been modified or altered Static Electricity Precautions It is quite easy to inadvertently damage your PC system board components or devices even before installing them in your system unit Static electrical discharge can damage computer components without causing any signs of physical damage You must take extra care in han dling them to ensure against electrostatic build up 1 To prevent electrostatic build up leave the system board in its anti static bag until you are ready to install it 2 Wear an antistatic wrist strap 3 Do all preparation work on a static free surface 4 Hold the device only by its edges Be careful not to tou
21. sync Adjust the monitor s vertical sync Move away any objects such as another monitor or fan that may be creating a magnetic field around the display Make sure your video card s output frequencies are supported by this monitor The screen seems to be constantly wavering 1 If the monitor is close to another monitor the adjacent monitor may need to be turned off Fluorescent lights adjacent to the monitor may also cause screen wavering Power Supply When the computer is turned on nothing happens 1 Check that one end of the AC power cord is plugged into a live outlet and the other end properly plugged into the back of the system Make sure that the voltage selection switch on the back panel is set for the correct type of voltage you are using The power cord may have a short or open Inspect the cord and install a new one if necessary Floppy Drive The computer cannot access the floppy drive 1 2 3 Appendix C Troubleshooting Checklist www dfi com The floppy diskette may not be formatted Format the diskette and try again The diskette may be write protected Use a diskette that is not write protected You may be writing to the wrong drive Check the path statement to make sure you are writing to the targeted drive There is not enough space left on the diskette Use another diskette with adequate storage space Appendix C Hard Drive System Board Hard disk failure 1 Make su
22. your operating system s manual or documentation for more information Wake On USB Keyboard Mouse The Wake On USB Keyboard Mouse function allows you to use a USB keyboard or USB mouse to wake up a system from the S3 STR Suspend To RAM state To use this function e Jumper Setting JP4 JP5 JP6 and JP8 must be set to 2 3 On 5V_standby Refer to USB Power Select in this chapter for more information I mportant ik If you are using the Wake On USB Keyboard Mouse function for 2 USB ports the 5V_standby power source of your power supply must support 21 5A For 3 or more USB ports the 5V_standby power source of your power supply must support 224A www dfi com Audio Rear Audio Line in Surround Line out Mic in Center Subwoofer Presence Signal Mic2 JD Key Line2 JD GND e N I OO Mic2 R Line2 R Mic2 L Front IO Sense O Line2 L Rear Audio The system board is equipped with 3 audio jacks A jack is a one hole connecting interface for inserting a plug e Line in Surround Jack Light Blue This jack is used to connect any audio devices such as Hi fi set CD player tape player AM FM radio tuner synthesizer etc e Line out Jack Lime This jack is used to connect a headphone or external speakers e Mic in Center Subwoofer Jack Pink This jack is used to connect an external microphone Front Audio The front audio connector allows you to connect to the second line ou
23. 0 H81C CPU Intel R Xeon R CPU E3 1268L v3 2 30GHz RAM 4 After completing installa iy DFI Utility InstallShield Wizard tion click Finish DFI Inc A The InstallShield Wizard has successfully installed DFI Utility 1 Information Click Finish to exit the wizard HW Health Chapter 4 Supported Software www dfi com Chapter 4 Status Case Close 5 E gi Enable Disable HEEE HEEE i Freer eg F TF F SRE RES HW Health Set DIO Enable watch dog function Setting Timer Value 255 Counting Mode Sec v Reset Mode Software 4 Keyboard 7 Mouse WatchDog Chapter 4 Supported Software www dfi com Intel USB 3 0 Drivers For Windows 7 To install the driver click Intel USB 3 0 Driver on the main menu l Setup is ready to install the driver Click Next 2 Read the license agreement then click Yes le e ime pm R USB3 T eXtensible Host Controller Driver intel Welcome to the Setup Program This setup program will install the following components Intel USB 3 0 eXtensible Host Controller Driver Intel USB 3 0 Hub Driver Intel USB 3 0 Host Controller Switch Driver Intel USB 3 0 Monitor Click Next to continue Intel Installation Framework Intel USB 3 0 eXtensible Host Controller Driver intel License Agreement You must accept all of the terms of the license agreement in order to con
24. 12 American Megatrends Inc NIC Configuration Link Speed This field is used to configure the network device Selects the link speed and duplex for the current network port Blink LEDs Wake on LAN Blink LEDs for the specified duration up to 15 seconds Enables this option to wake the system with a magic packet Link Status This field indicates the link status of the network device 44 Chapter 3 BIOS Setup www dfi com Chapter 3 Intel R 82574L Gigabit Network Connection 00 01 29 12 NI C Configuration This section is used to configure the parameters of the Gigabit Ethernet device This field is used to configure the network device Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt NIC Configuration Link Speed AutoNeg Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc NIC Configuration Link Speed This field is used to configure the network device Selects the link speed and duplex for the current network port Blink LEDs Wake on LAN Blink LEDs for the specified duration up to 15 seconds Enables this option to wake the system with a magic packet Link Status This field indicates the link status of the network device Alternate MAC Address Alternates assigned MAC address of Ethernet port 45 Chapter 3 BIOS Setup www dfi co
25. FOFE FF 1C 4c41 BE37 A027 1FC90396 Shell Oper Creating Process C Windows Microsoft NET Framework v2 0 50727 ngen exe Creating Registry Key HKLM System CurrentControlSet Services laStorDataMarSvc Delayed Creating Registry Key HKLM SOFTWARE INTEL VRST WinUiLocation 2C Program Files x86 V Creating Registry Key HKLM SOFTWARE MicrosoftlWindows CurrentVersion Run IAStorIcon Creating Registry Key HKLM SOFTWARE INTEL IRST RAIDNotificationIcon 2 dw Creating Registry Key HKLM SOFTWARE Intel ICC Applications IRST Path C ProgramData Installing Intel Control Center 3 Click Next to continue P T Intel Installation Framework Chapter 4 iussi aile ind iz NN E Infineon TPM Driver and Tool optional computer now then click Finish _ HU Inteice Rapid Storage Tease intel To install the driver click Infineon TPM driver and tool option on the main menu Restarting the system will allow the Setup Is Complete Wc d dinge S 1 The setup program is preparing Infineon TPM Professional Package InstallShield Wizard You must restart this computer for the changes to take effect Would you like to restart the to install the driver computer now Preparing to Install Yes I want to restart this computer now Infineon TPM Professional Package Setup is preparing the restart thi InstallShield Wizard which will guide you through the program Q1 Ie MER setup process Please wa
26. Graphics Medis Accelerator Drie unirea TH Copying Pile C Program Piles JInbel Intel R Graphics Meada Accelerator Driver luninetallith TH Piles C Program Fillesidnrehiinte R Graphics Medis rceler stor Ceteerluniret s br TR EM c Program Finallen Intel Graphics Media Accelerator Deter unia TRA File Coming Comanag Coping Copying Piles CilProgram Filesidobef Intel R Graphics Medias Accelerator Ceteerluniretalzh TV Coping Filz 2 Program Filesidebsh Intel Graphics Pieds fcceler stor Deherlu al ch TV Copying Fiac CWINDCORM S ptum dif casi oil Program FilesUiebefi rte R Graphics Meda Accelerator Drier uriia hT Cifrcgeam Filezinbef Graphics Medias Arrei ator Deteeriuniret alil the Click Nest bo continue Marra 5 Click Yes want to restart Intel Graphics Media Accelerator Driver this computer now then click Finish Intel Graphics Media Accelerator Driver intel Setup Is Complete Restarting the system will allow the Hey softwa be instal lation to You must restart this computer For the changes to take effect Would you like to restart the take effect computer now Yes I want to restart this computer now No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Chapter 4 Supported Software www dfi com I ntel Graphics Drivers For Windows 7 and Windows 8 To instal
27. IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Equipment Manufacturer OEM Independent Hardware Vendor IHV or meaane Software Vendor ISV this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT Intel Installation Framework 3 Setup is currently installing the driver After installation has completed click Next Intel Management Engine Components Setup Progress Please wait while the following setup operations are performed Creating Process regsvr32 exe Creating Process regsvr32 exe Copying File C Windows system32 drivers IntelMEFW Ver dll Creating Process C Program Files Intel Intel R Management Engine Components FWService Deleting File C Program Files Intel Intel R Management Engine Components FWService Inte Copying File C Program Files Intel Intel R Management Engine Components FWService Inte Creating Process C Program Files Intel Intel R Management Engine Components FWService Creating Process C Program Files Intel Intel R Management Engine Components FWService In
28. Intel Untel R USB 3 0 eXtensible Host Controller Driver A Program Files x86 Intel Intel R USB 3 0 eXtensible Host Controller Driver A Program Files x86 Intel Intel R USB 3 0 eXtensible Host Controller Driver A Program Files x86 Intel Intel R USB 3 0 eXtensible Host Controller Driver A tea Nt aN USB 3 0 eXtensible Host Controller Driver Setup Is Complete intel You must restart this computer for the changes to take effect Would you like to restart the computer now Yes I want to restart this computer now C No I will restart this computer later Click Finish then remove any installation media from the drives Intel Installation Framework Chapter 4 Supported Software www dfi com Chapter 4 Intel Rapid Storage Technology For Windows 7 and Windows 8 The Intel Rapid Storage Technology is a utility that allows you to monitor the current status of the SATA drives It enables enhanced performance and power management for the storage subsystem To install the driver click Intel Rapid Storage Technology on the main menu 1 Setup is now ready to install the utility Click Next 2 Read the warning then click Yes ces C an Intel Rapid Storage Technology intel Welcome to the Setup Program This setup program will install Intel Rapid Storage Technology onto this computer It is strongly recommended that you exit all programs before continuing Click Ne
29. Ipv4 PXE boot supports When disabled pv4 PXE boot option will not be created This section is used to enable or disable UEFI network stack Aptio Setup Utility Copyright C 2012 American Megatrends Inc I pv6 PXE Support pee a ce When enabled pv6 PXE boot supports When disabled pv6 PXE boot option will not be created Version 2 15 1236 Copyright C 2012 American Megatrends Inc When Network Stack is enabled it will display the following information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Network Stack Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 43 a ASA o UP M n s n m m Chapter 3 BIOS Setup www dfi com Chapter 3 Intel R Ethernet Network Connection i217 LM 00 01 29 NI C Configuration This section is used to configure the parameters of the Gigabit Ethernet device This field is used to configure the network device Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Link Speed AutoNeg gt NIC Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 20
30. PCI slot supports expansion cards that comply with PCI specifications You can install a PCI expansion card or a customized riser card designed for only 2 PCI slots expansion for low profile PCI card only into the PCI slot PCI Express x4 Slot Install PCI Express cards such as network cards or other cards that comply to the PCI Express specifications into the PCI Express x4 slot ISA Slot The ISA slot is used to connect ISA compatible expansion cards www dfi com S PDI F Connector Parallel Port SPDIF out Key Ground S PDIF a SPDIF in Ta mmni The S PDIF connector is used to connect an external S PDIF port Your S PDIF port may be mounted on a card edge bracket Install the card edge bracket to an available slot at the rear of the system chassis then connect the audio cable to the S PDIF connector Make sure pin 1 Ihn pi coniector is used to connetan external parallel pore The parallel pore conned of the audio cable is aligned with pin 1 of the S PDIF connector z i ins SS dd your PC to a parallel printer It supports SPP ECP and EPP SPP Allows normal speed operation but in one Standard Parallel Port direction only ECP Allows parallel port to operate in bidirectional Extended Capabilities Port mode and at a speed faster than the SPP s data transfer rate EPP Allows bidirectional parallel port operation at Enhanced Parallel Port maximum speed Chapter 2 Hardware Installation w
31. Power Management Wake On Events include Wake On PS 2 KB Mouse Wake On USB KB Mouse Wake On LAN RTC timer to power on the system e CPU stopped clock control AC power failure recovery Monitors CPU system temperature and overheat alarm Monitors VCORE 5V 3 3V V DI MM 12V 5VSB voltages and failure alarm Monitors CPU system fan speed and failure alarm Read back capability that displays temperature voltage and fan speed e TBD e Operating 0 C to 60 C Storage 20 C to 85 C e 5 to 90 Chapter 1 Introduction WWW dfi com OS Support e Windows XP Professional x86 amp SP3 32 bit limited function Features e Watchdog Timer The Watchdog Timer function allows your application to regularly clear the system at the set time interval If the system hangs or fails to function it will reset at the set time interval so that your system will continue to operate e DDR3 DDR3 delivers increased system bandwidth and improved performance It offers peak data transfer rate of up to 16Gb s bandwidth The advantages of DDR3 are its higher bandwidth Note i n n n perform han DDR2 LE Optional and is not supported in standard model Please contact your sales represen EH ends Wt Pemou ance 2 IOVI power ek tative for more information Dimensions Certification e Graphics The integrated Intel HD graphics engine delivers an excellent blend of graphics performance and features
32. X OU CLER AQUA a ka UR d EAR a a NS 26 CODI P 2 beir Eannachaite a ee a TE AA ALA HH a TH a a HH AH an in 26 Chassis Intrusion CONNEC uiuere eorr eorr errem m v n e ene a an cea 27 Bre ar i oi mm v mmm mm mrmrmrmrrmrmrrmrmrHH 2 Front Panel ConneCtOr couissncsise i siveaniaisdawenspobcaweeotsinsetisundecesweomuueiesdatmueeeabens 27 Standby Power LED scssi iniri naen AREA IR San aig NOR A Rian KORR ERR DOKN SO ER Giada 28 FCC and DOC Statement on Class B 5 Expansi n SIOUS sessin aa Eear a E a EA EAEE E a Ed 28 S PDIF Connector aerate eat eee oe geet ei ek ee aes aa aaa e Eie ai a 29 Parallel POI d c ai ac aist 29 About this Manual seem nre rri 4 orco PAM MM CAM NEM MM i SMBUS Connector seen einaie dii ara bets xix ea E desea USI EES UA salve tis iau n duri 30 Warranty side Aue a keg BE Meek van de wid ale da elie ed ade Molen Dea Rae ee ee ee ME ee ee AA 4 LAN LED Connector occ cece cece cccccccce ence ce cece ce cebe be bebe bebe bbe be bebe be ul 31 lat Ia p T M P 31 Static Electricity Precautions eene 4 Chapter 3 BIOS Setup ssssessseeeneee nennen 32 Safety Measures ssssssssseseeeeeeeneete nter enn tnn nrr ntes ne testas irse sna 4 erc ER 32 About the Packs aset ti
33. ce tcn eo bais tme oon D g sa ai E 5 AMI BIOS Setup DIG iss ierit tete Ek ma pcc Oa oc lic p 33 Maln ie cae m TR eee eae 33 Chapter 1 Introduction mvvvwwvvvvvwmvvsvisvmwwuuvvv 6 Advanced ENNIO CRT 33 l c 46 Specifications Fae St en AE ee ee 6 Boot i oyna ive Us xim mv Shi oe dev cu ure E x vu UU immi E st RU A faye Ue au e are leans va ue v wu a seh TU are E 53 Feat SECUN Ea 54 eat ES PC re me ee M 7 E RENE 54 Updating the BIOS eesseeseseseseennneennennnnnnn nennen nnne nnns 55 STI enc FIFA CETOUSISCIHIDIET eductestusncetulizst utut rnit nn eite Notice BIOS SPI ROM 55 218 a coy Mer 9 y Chapter 4 Supported Software esssssss 56 System Memory ANTT 9 Installing the DIMM Module eeeeeeeeeeenneneeeennseeeennneneeeenneeeeeeeneeeeenneeeeens 10 oi CPU a Chapter 5 Digital 1 O Programming Guide 74 iNstalling te CPU e tenes 12 Installing the Fan and Heat Sink eueeueeseeeeeeeeeeeeeeeeeeeeereee 14 Appendix A Watchdog Sample Boe c 76 Jumper Settings seconded Dau d MD MM MM ME MEME 15 qe susc c 15 Appendix B System Error Message Xspdnuipbenadulquine Seen ae eee eR rane Nae 77 PS 2 Keyb
34. ch any of the components contacts or connections 5 Avoid touching the pins or contacts on all modules and connectors Hold modules or con nectors by their ends I mportant fa Electrostatic discharge ESD can damage your processor disk drive and other com ponents Perform the upgrade instruction procedures described at an ESD worksta tion only If such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chas sis If a wrist strap is unavailable establish and maintain contact with the system chassis throughout any procedures requiring ESD protection Safety Measures To avoid damage to the system e Use the correct AC input voltage range To reduce the risk of electric shock e Unplug the power cord before removing the system chassis cover for installation or servic ing After installation or servicing cover the system chassis before plugging the power cord About the Package The package contains the following items If any of these items are missing or damaged please contact your dealer or sales representative for assistance One HD620 motherboard One Serial ATA data cable One I O shield One DVD One QR Quick Reference The board and accessories in the package may not come similar to the information listed above This may differ in accordance to the sales region or models in which it was sold For more informatio
35. d to configure the CPU It will also display the detected CPU information This section is used to configure the settings of SATA device Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc SATA Controller s Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Hyper threading Enabled SATA Controller s Version 2 15 1236 Copyright C 2012 American Megatrends Inc This field is used to enable or disable the Serial ATA devices Hyper threading SATA Mode Selection Enables this field for Windows XP and Linux which are optimized for Hyper Threading The mode selection determines how the SATA controller s operates technology Select disabled for other OSes not optimized for Hyper Threading technol ogy When disabled only one thread per enabled core is enabled IDE Mode This option configures the Serial ATA drives as Parallel ATA storage devices Active Processor Cores AHCI Mode This option allows the Serial ATA devices to use AHCI Advanced Host Controller nter Number of cores to enable in each processor package feo ace Intel Virtualization Technology When this field is set to enabled a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology EIST This field is used to enable or disable the Intel Enhanced SpeedStep Technology 35 i Chapter 3 BIOS Setup www dfi com
36. d used on another system board of the same model To execute the utility type 2 The BIOS SPI ROM on this system board must be the original equipment from the factory A AFUDOS BIOS File Name b p n and cannot be used to replace one which has been utilized on other system boards then press lt Enter gt 3 If you do not follow the methods above the Intel Management Engine will not be updated and will cease to be effective C NAFUMVAFUDOS afudos filename B P N AMI Firmware Update Utility APTIO v2 25 Note depu aee E n a You can take advantage of flash tools to update the default configuration of the nete BIOS SPI ROM to the latest version anytime Erasing flash b When the BIOS IC needs to be replaced you have to populate it properly onto the ed M system board after the EEPROM programmer has been burned and follow the Erasing BootBlock technical person s instructions to confirm that the MAC address should be burned Writing BootBlock Verifying BootBlock or not CANAFUMAFUDOS 55 Chapter 3 BIOS Setup www dfi com Chapter 4 Chapter 4 Supported Software For Windows 7 The CD that came with the system board contains drivers utilities and software applications required to enhance the performance of the system board Insert the CD into a CD ROM drive The autorun screen Mainboard Utility CD
37. date Wizard The wizard has finished installing the software for E Intel R Ethernet Connection 1217 LM E Click Finish to close the wizard lt Back K Cancel dal Huan niare Drica H E IDE RT AIT AF corirolara Hi oboe d j Fia aed other piring drem a linrearmad Serial Bum controlam Intel LAN Drivers For Windows 7 and Windows 8 To install the driver click Intel LAN Drivers on the main menu l Setup is ready to install the driver Click Next 2 Click I accept the terms in the license agreement then click Next 3 Select the program featuers you want installed then dick Next iz Intel R Network Connections InstallShield Wizard Welcome to the InstallShield Wizard for Intel R Network Connections Installs drivers Intel R PROSet For Windows Device Manager and Advanced Networking Services WARNING This program is protected by copyright law and international treaties Installshield c ome ie Intel R Network Connections InstallShield Wizard License Agreement Please read the following license agreement carefully INTEL SOFTWARE LICENSE AGREEMENT Final License IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of
38. ding to local ordinance www dfi com Chapter 3 Chapter 3 BIOS Setup Legends Overview l Keys Function The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals It contains codes for various advanced features found in this system board Right and Left arrows Moves the highlight left or right to select a menu The BIOS allows you to configure the system and save the configuration in a battery backed CMOS so that the data retains even when the power is off In general the information stored Up and Down arrows Moves the hightlight up or down between submenu or fields in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been made such as a hard drive replaced or a device added C EM Exit to the BIOS Setup Utility It is possible that the CMOS battery will fail causing CMOS data loss If this happens you need plus key Scrolls forward through the values or options of the highlighted field to install a new CMOS battery and reconfigure the BIOS settings y minus key Scrolls backward through the values or options of the highlighted field Note LE The BIOS is constantly updated to improve the performance of the system board Tab Select a field therefore the BIOS screens in this chapter may not appear the same as the actual one These screens are for reference purpose only F1 Displays general help lt F2 gt Pervious values Default C
39. e The higher the temperature the faster the speed of rota tion gt Serial Port 6 Configuration Boundary 1 to Boundary 4 The range is 0 127 Speed Count 1 to Speed Count 5 The range is 1 100 Case Open Sets this field to Enabled to allow the system to alert you of a chassis intrusion event Version 2 15 1236 Copyright C 2012 American Megatrends Inc Serial Port 6 Configuration to Serial Port 9 Configuration Sets the parameters of serial port 6 to serial port 9 Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 41 Chapter 3 BI OS Setup www dfi com Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 42 Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Serial Port Enables or disables these serial ports COM Change Settings Selects the I O I RQ settings for the super I O device Chapter 3 Network Stack Ipv4 PXE Support When enabled
40. e continuing 2 Read the license agreement Intel Chipset Device Software then click Yes Intel Chipset Device Software License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the Following terms and conditions By loading or using the Software you agree to the terms of this Agreement IF you do not wish to so agree do not install or use the Software Please Also Note TF you are an Original Equipment Manufacturer OEM Independent Hardware Vendor IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies i Back No Intel Installation Framework Chapter 4 Supported Software www dfi com Chapter 4 3 Go through the readme Intel Chipset Device Software E Microsoft DirectX 9 0C For Windows XP document for more installa i tion tips then click Next Intel Chipset Device Software To install the utility click Microsoft DirectX 9 0C Driver on the main menu Readme File Information l Click accept the Installing Microsoft R DirectX R Refer to the Readme file below to view the system requirements and installat
41. e up a Soft Power Down Soft Off PC It is supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME Power Man agement Event signal However if your system is in the Suspend mode you can power on the system only through an IRQ or DMA interrupt I mportant ik The 5V standby power source of your power supply must support 2720mA e Wake On USB This function allows you to use a USB keyboard or USB mouse to wake up a system from the S3 STR Suspend To RAM state I mportant ik If you are using the Wake On USB Keyboard Mouse function for 2 USB ports the 5V standby power source of your power supply must support 21 5A For 3 or more USB ports the 5V standby power source of your power supply must support 224A e RTC Timer The RTC installed on the system board allows your system to automatically power on on the set date and time e ACPI STR The system board is designed to meet the ACPI Advanced Configuration and Power Interface specification ACPI has energy saving features that enables PCs to implement Power Manage ment and Plug and Play with operating systems that support OS Direct Power Management ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM function With the Suspend to RAM function enabled you can power off the system at once by pressing the power button or selecting Standby when you shut down Windows without having to go through the sometimes tireso
42. efault 3 2 1 2 3 On 5V 1 1 1 2 On 5V or 2 3 On GND 5V_standby i default 3 3 JP13 is used to select the power of DIO Digital I O signal i B Based on the power level of DIO Digital I O selected on JP13 JP12 DIO pin 3 5 7 9 and JP7 DIO pin 11 13 15 17 are used to select the state of DIO output pull high or pull low When selecting pull high the power selection will be the same as JP13 s setting Chapter 2 Hardware Installation www dfi com Rear Panel I O Ports Line in Surround Line out Mic in Center Subwoofer COM 1 DVI D USB 3 0 USB 2 0 The rear panel I O ports consist of the following e 1 PS 2 Keyboard Mouse port e 2 Serial COM ports e 1 VGA port e 1 DVI D port e 2 RJ45 LAN ports HD620 H81B has LAN 1 only 2 USB 3 0 ports 4 USB 2 0 ports Line in Surround jack Line out jack Mic in Center Subwoofer jack Chapter 2 Hardware Installation PS 2 Keyboard Mouse Port This rear I O port is used to connect a PS 2 keyboard mouse The PS 2 mouse port uses IRQ12 Wake On PS 2 Keyboard Mouse The Wake On PS 2 Keyboard Mouse function allows you to use the PS 2 keyboard or PS 2 mouse to power on the system To use this function e Jumper Setting JP1 must be set to 2 3 On 45V standby Refer to PS 2 KB MS Power Select in this chapter for more information e BIOS Setting Configure the wake up function of PS 2 keyboard mouse in the Advanced menu
43. eld ETE m Chapter 4 Supported Software www dfi com Chapter 4 4 Enter the necessary information i Infineon TPM Professional Package InstallShield Wizard x 7 TPM requires installing the Micro and then click Next Customer Information soft Visual C package prior to Installing Infineon TPM Professional Package Please enter your information installing the utility Click Install The program features you selected are being installed Please wait while the InstallShield Wizard installs Infineon TPM Professional Package This may take several minutes User Name Organization pe Status Installing Microsoft Visual C 2010 SP1 Redistributable Package InstallShield Installshield m fe 5 Select a setup type and then click i Infineon TPM Professional Package InstallShield Wizard E3 8 The setup program is cu rrently i Infineon TPM Professional Package InstallShield Wizard Next Setup Type installi ng the Microsoft Visual Installing Infineon TPM Professional Package Choose the setup type that best suits your needs C package The program features you selected are being installed Please select a setup type Please wait while the InstallShield Wizard installs Infineon TPM Professional Package This may take several minutes Complete All program Features will be installed Requires the most disk space Status Copying new files Choose which program Features you want installed and wh
44. em boots it will first initialize the PCI Express x16 graphics card cC DVMT e totar graphics Memory SIZE eer ey Tentera grapes Qevice Please refer to the screen shown below I nternal Graphics Aptio Setup Utility Copyright C 2012 American Megatrends Inc Keeps IGD enabled based on the setup options DVMT Total Gfx Mem 256M DVMT Total Gfx Mem 128M 256M MAX Version 2 15 1236 Copyright C 2012 American Megatrends Inc 47 LCD Control This field configures the LCD control Aptio Setup Utility Copyright C 2012 American Megatrends Inc Primary IGFX Boot Display VBIOS Default Version 2 15 1236 Copyright C 2012 American Megatrends Inc When any device is selected in the Primary I GFX Boot Display it will display the following information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Primary IGFX Boot Display Version 2 15 1236 Copyright C 2012 American Megatrends Inc Secondary I GFX Boot Display Selects the secondary display device 48 NB PCI e Configuration This field is used to configure the settings of NB PCI Express Aptio Setup Utility Copyright C 2012 American Megatrends Inc PEGO Gen X Version 2 15 1236 Copyright C 2012 American Megatrends Inc Enable PEG Enables or disables the PEG Chapter 3 Memory Configuration PCH IO Configuration This field only displays the memory configuration This section illustrates the PCH
45. er you Driver I nstallation plug the cable connector into the DVI D port gently tighten the cable screws to hold the con nector in place Install the LAN drivers Refer to the chapter 4 for more information BI OS Setting Note LE HD620 H81B supports Intel 82574 PCI Express Gigabit Ethernet controller LAN 1 Configure the display devices in the Chipset menu System Agent Configuration submenu of only the BIOS Refer to the chapter 3 for more information Chapter 2 Hardware Installation www dfi com USB Ports USB 1 USB 0 USB 3 0 USB 5 USB 4 USB 2 0 The USB device allows data exchange between your computer and a wide range of simultane ously accessible external Plug and Play peripherals The system board is equipped with two onboard USB 3 0 ports USB 0 1 and four onboard USB 2 0 ports USB 4 5 8 9 The 10 pin connectors allow you to connect 4 additional USB 2 0 1 1 ports USB 2 3 10 11 The additional USB ports may be mounted on a card edge bracket Install the card edge bracket to an available slot at the rear of the system chassis and then insert the USB port cables to a connector Chapter 2 Hardware Installation BI OS Setting Configure these onboard USB devices in the Advanced menu USB Configuration submenu of the BIOS Refer to the chapter 3 for more information Driver Installation You may need to install the proper drivers in your system operation to use the USB device Re fer to
46. ere they will be installed Recommended For advanced users InstallShield InstallShield 9 Click Finish 6 Click Install i Infineon TPM Professional Package InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to The Instaltheld A Wizard vell mail Infineon TPM Professional exit the wizard Package nn your computer To continue click ent WARNING Ths program is procected by conright lew and interational basies Installshield Chapter 4 Supported Software www dfi com Chapter 4 10 Click Yes to restart your system ii Infineon TPM Professional Package Installer Info Adobe Acrobat Reader 9 3 You must restart your system for the configuration To install the reader click Adobe Acrobat Reader 9 3 on the main menu changes made to Infineon TPM Professional Package to take effect Click Yes to restart now or No if you plan to restart later l Click Next to install or click i Adobe Reader 9 3 Setup Change Destination Folder to select another folder px Destination Folder Click Next to install to this folder or click Change to install to a different Folder A Install Adobe Reader 9 3 to C Program FilesAdobelReader 9 0 WARNING This program is protected by copyright law and interna
47. figuration I2C ReadByte SLAVE ADDR CONFIG PORT amp Data if Mode 1 SetBit amp Data TempPinNum 1nput else CirBit amp Data TempPinNum Output I2C WriteByte SLAVE ADDR CONFIG PORT Data return 1 Chapter 5 Digital l O Programming Guide Chapter 5 Z5 GPI O Output Process define SLAVE ADDR Ox42 define INPUT PORT 0x00 define OUTPUT_PORT OxO1 define INVERSION PORT 0x02 define COMFIG PORT 0x03 GpioOut int PinNum int Level BYTE Data BYTE TempPinNum PinNum 68 PinO 7 I2C ReadByte SLAVE ADDR OUTPUT PORT amp Data if Level O CIrBit amp Data TempPinNum else SetBit amp Data TempPinNum I2C WriteByte SLAVE ADDR OUTPUT PORT Data return 1 GPIO utput Process define SLAVE ADDR Ox42 define INPUT PORT OxOO define OUTPUT PORT OxO1 define INVERSION PORT 0x02 define COMFIG PORT 0x03 Gpiol n int PinNum int Status BYTE Data BYTE Group PinNumy8 BYTE TempPinNum PinNum 8 PinO 7 I2C ReadByte SLAVE ADDR INPUT PORT amp Data Status GetBit Data TempPinNum return 1 www dfi com Appendix A Appendix A Watchdog Sample Code Software programming example MOV DX AEH MOV AL 87H OUT DX AL OUT DX AL timer MOV DX 4EH MOV AL O7H Ready to Program Logical Device OUT DX AL MOV DX 4FH MOV AL O8H Select Logical Device 8 OUT DX AL MOV DX 4EH MOV AL F1H Select watchdog timer register OUT DX AL
48. firmly until it is completely seated in the socket 8 The ejector tabs at the ends of the socket will automatically snap into the locked position to hold the module in place Chapter 2 Hardware Installation CPU The system board is equipped with a surface mount LGA 1150 socket This socket is exclu sively designed for installing a LGA 1150 packaged Intel CPU I mportant ik 1 Before you proceed make sure 1 the LGA 1150 socket comes with a protective cap 2 the cap is not damaged and 3 the socket s contact pins are not bent If the cap is missing or the cap and or contact pins are damaged contact your dealer immediately 2 Make sure to keep the protective cap RMA requests will be accepted and pro cessed only if the LGA 1150 socket comes with the protective cap Protective cap Note z The system board used in the following illustrations may not resemble the actual board These illustrations are for reference only www dfi com Installing the CPU 5 Lifting the load lever will at Load lever the same time lift the load 1 Make sure the PC and all other peripheral devices connected to it has been powered down plate 2 Disconnect all power cords and cables Lift the load lever up to the angle shown on the Load photo plate 3 Locate the LGA 1150 CPU socket on the system board 6 Remove the protective cap from the CPU socket The cap is used t
49. gure the parameters of the USB device Aptio Setup Utility Copyright C 2012 American Megatrends Inc Legacy USB Support Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Legacy USB Support Enabled Enables legacy USB Auto Disables support for legacy when no USB devices are connected Disabled Keeps USB devices available only for EFI applications USB 3 0 Support Enables or disables USB 3 0 XHCI Controller support XHCI Hand off This is a workaround for OSes without XHCI hand off support The XHCI ownership change should be claimed by XHCI driver EHCI Hand off This is a workaround for OSes that does not support EHCI hand off The EHCI owner ship change should be claimed by the EHCI driver This section is used to configure the I O functions supported by the onboard Super I O chip Aptio Setup Utility Copyright C 2012 American Megatrends Inc Restore AC Power Loss Power Off Version 2 15 1236 Copyright C 2012 American Megatrends Inc Restore AC Power Loss Power Off When power returns after an AC power failure the system s power is off You must press the Power button to power on the system Power On When power returns after an AC power failure the system will automatically power on Last State When power returns after an AC power failure the system will return to the state where you left off before power failure occurs If the system s power is off w
50. hat you may encounter with your personal computer To efficiently troubleshoot your system treat each problem indi vidually This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes Some of the most common things to check when you encounter problems while using your system are listed below l The power switch of each peripheral device is turned on 2 All cables and power cords are tightly connected 3 The electrical outlet to which your peripheral devices are connected is working Test the outlet by plugging in a lamp or other electrical device 4 The monitor is turned on 5 The display s brightness and contrast controls are adjusted properly 6 All add in boards in the expansion slots are seated securely 7 Any add in board you have installed is designed for your system and is set up correctly Monitor Display If the display screen remains dark after the system is turned on l Make sure that the monitor s power switch is on 2 Check that one end of the monitor s power cord is properly attached to the monitor and the other end is plugged into a working AC outlet If necessary try another outlet 3 Check that the video input cable is properly attached to the monitor and the system s display adapter 4 Adjust the brightness of the display by turning the monitor s brightness control knob The picture seems to be constantly moving 1 2 3 The monitor has lost its vertical
51. hen AC power failure occurs it will remain off when power returns If the system s power is on when AC power failure occurs the system will power on when power returns Watchdog Timer Unit Selects the watchdog timer unit second or minute Super IO Watchdog Timer Sets the timeout value of the super 1O watchdog timer 0 means disabled 38 Serial Port O Configuration to Serial Port 5 Configuration Sets the parameters of serial port 0 COM A to serial port 5 COM F Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 29 Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Serial Port E
52. ion information mm a Press the Page Down key to view the rest of the File agreement then click Next dC A NN A o NR RN NN UU Nuus ee ee a Product Intel R Chipset Device Software Release Production Version Version 9 0 0 1008 Welcome to setup for DirectX The Direct setup wizard guides you through installation of Direc Runtime Components Please read the following license agreement Press the PAGE DOWN key to see the rest of the agreement Y ou must accept the agreement to continue the setup MICROSOFT Direct 3 c Target Chipset Intel R 4 Series Chipset Date May O1 2008 orc oW Wo Wo Wo o o o o o o o o o o o a Rs s a a a a SUPPLEMENTAL END USER LICENSE AGREEMENT FOR MICROSOFT SOFTWARE Supplemental EULA IMPORTANT READ CAREFULLY These Microsoft Corporation Microsoft operating system components including any online or electronic documentation OS Components are subject to the terms and conditions of se M a i i Back Cancel Intel Installation Framework accept the agreement C don t accept the agreement Bach Cancel 4 Click Finish to exit setup Intel Chipset Device Software Intel Chipset Device Software Setup Is Complete 2 To start installation click Installing Microsoft R DirectX R Next DirectX Setup The setup program successfully installed the Intel Chipset Device Software onto this computer Install Directe runtime co
53. is software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software IHV or Independent Software Vendor ISV this complete LICENSE AGREEMENT applies If you are an End User then only Exhibit A the INTEL SOFTWARE LICENSE AGREEMENT 7 Intel Installation Framework e oe x 5 mes Intel Rapid Storage Technology intel Readme File Information Refer to the Readme file below to view the system requirements and installation information Installation Readme for Intel R Rapid Storage Technology Intel R RST Refer to the system requirements for the operating systems supported by Intel Rapid Storage Technology This document makes references to products developed by Intel There are some restrictions on how these products others Please read the Disclaimer section at the bottom Intel Installation Framework EE Intel Rapid Storage Technology intel Setup Progress Please wait while the following setup operations are performed Creating Registry Key HKCR CLSID E342F0FE FF 1C 4c41 BE37 A0271FC90396 System Cc a Creating Registry Key HKCRYCLSIDME342FOFE FF 1C 4c41 BE37 A027 1FC90396 DefaultIco Creating Registry Key HKCRYCLSIDME342
54. it Click Finish then remove any installation media from the drives Configuring Windows Installer Intel Installation Framework 2 The setup program is now ready i Infineon TPM Professional Package InstallShield Wizard to install the utility Click Next welcome to the InstallShield Wizard for Infineon TPM Professional Package Version 4 3 100 3287 The InstallShield R wizard will install Infineon TPM Professional Package on your computer To continue click Next It is recommended that you close all other applications before starting Setup WARNING This program is protected by copyright law and international treaties oe ones 3 Click I accept the terms in the i Infineon TPM Professional Package InstallShield Wizard license agreement and then H 44 7 cl ick Next Please read the Following license agreement carefully License Agreement Software Setup End User License Conditions for the Infineon TPM Professional Package 1 Attention This software contains copyright protected content e g codes and structures and confidential content e g algorithms ideas and concepts of Infineon Technologies AG and Microsoft Corporation Microsoft patterns amp practices Enterprise Library Microsoft Corporation Athana inanan tauma and aancditiawn flhawninafiaw tha Cancitinws i accept the terms in the license agreement O1 do not accept the terms in the license agreement Installshi
55. l 82574 PCI Express Gigabit Ethernet controller e Intel 1217LM Gigabit Ethernet Phy HD620 H81X D e Integrated 10 100 1000 transceiver Fully compliant with IEEE 802 3 IEEE 802 3u IEEE 802 3ab e 2 SATA 3 0 ports with data transfer rate up to 6Gb s SATA port 1 provides adequate space for SATA DOM 2 SATA 2 0 ports with data transfer rate up to 3Gb s e Integrated Advanced Host Controller Interface AHCI controller 1 mini DI N 6 port for PS 2 mouse keyboard 2 DB 9 serial ports Supports RS232 422 485 RS232 and or Power 1 VGA port e 1 DVI D port e 2 RJ45 LAN ports e 2 USB 3 0 ports 4 USB 2 0 ports e Line in Surround Line out Mic in Center Subwoofer jacks 2 connectors for 4 external USB 2 0 1 1 ports 8 connectors for 8 external RS232 serial ports 2 0mm pitch HD620 H81X only e 1 vertical USB 2 0 1 1 port optional e 1 8 bit Digital I O connector e 1 front audio connector for line out and mic in jacks e 1 LAN LED connector e 1 S PDIF connector 1 parallel port 4 Serial ATA ports 1 24 pin ATX power connector 1 8 pin 12V power connector 1 chassis intrusion connector e 1 front panel connector 2 fan connectors AMI BIOS 64Mbit SPI BIOS e Software programmable from 1 to 255 seconds Provides a Trusted PC for secure transactions Provides software license protection enforcement and password protection e Supports ErP Lot6 power saving optional e Supports ACPI System
56. l the driver click Intel Graphics Drivers on the main menu l Setup is now ready to install the graphics driver Click Next Intel HD Graphics Driver intel Welcome to the Setup Program This setup program will install the following components Intel HD Graphics Driver Intel amp Display Audio Driver It is strongly recommended that you exit all programs before continuing Click Next to continue V Automatically run WinSAT and enable the Windows Aero desktop theme if supported Intel Installation Framework By default the Automatically run WinSAT and enable the Windows Aero desktop theme is enabled With this enabled after installing the graphics driver and the system rebooted the screen will turn blank for 1 to 2 minutes while WinSAT is running before the Windows Vista desktop appears The blank screen period is the time Windows is testing the graphics perfor mance 2 Read the license agreement then click Yes Intel HD Graphics Driver License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software S pias cream Ei Uer Bem andy Cult tas INTE
57. lable for that field To display the submenu move the highlight to that field and press lt Enter gt 32 Chapter 3 BIOS Setup www dfi com Chapter 3 AMI BIOS Setup Utility Advanced M a The Advanced menu allows you to configure your system for basic operation Some entries are ain defaults required by the system board while others if enabled will improve the performance of your system or let you set some features according to your preference The Main menu is the first screen that you will see when you enter the BIOS Setup Utility I mportant Aptio Setup Utility Copyright C 2012 American Megatrends Inc ik Setting incorrect field values may cause the system to malfunction Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt ACPI Power Management Configuration System Language English Version 2 15 1236 Copyright C 2012 American Megatrends Inc System Date Version 2 15 1236 Copyright C 2012 American Megatrends Inc The date format is lt day gt lt month gt lt date gt lt year gt Day displays a day from Sun day to Saturday Month displays the month from J anuary to December Date displays the date from 1 to 31 Year displays the year from 1980 to 2099 System Time The time format is lt hour gt lt minute gt lt second gt The time is based on the 24 hour military time clock For example 1 p m is 13 00 00 Hour displays hours from OO to 23 Minute di
58. le protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encour aged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Notice l The changes or modifications not expressly approved by the party responsible for compli ance could void the user s authority to operate the equipment 2 Shielded interface cables must be used in order to comply with the emission limits Table of Contents P Eo o NER NERO m 24 VO 6 ag ai ta tT ER NT 24 SATA Serial ATA CONNECUOIS ccc cccee eee e ee cce eee ehem nnne nescis nene nnn 24 Digital O COM y ars ge 25 jii Cooling Fan ConnecLol S soavs sexo a a doni a Roa
59. local paths and removable media The best driver found will be installed Y Search removable media floppy CD ROM _ Include this location in the search C Documents and Settings dfi Desktop CONGATE Browse Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Cea JL nens Hardware Update Wizard Hardware Type Select a hardware type and then click Next Common hardware types e Batteries Bluetooth Radios P Computer Se Disk drives L Display adapters DVD CD ROM drives Floppy disk controllers E Floppy disk drives PFa Himan Intarfsce Navinas w Hardware Update Wizard Select the device driver you want to install for this hardware o Select the manufacturer and model of your hardware device and then click Next If you have a disk that contains the driver you want to install click Have Disk CD ROM Drive force CDDA accurate EF CD ROM Drive force CDDA inaccurate EF CD ROM Drive force IMAPI disable Sv CD ROM Drive IMAPI settings 0 1 mam mm gk This driver is digitally signed Tell me why driver signing is important 6 Insert the installation disk and make sure the selected drive is correct 7 Select the device driver you want to install for this hardware and then click Next
60. m Chapter 3 Chipset System Agent SA Configuration This section is used to configure the parameters of System Agent This section configures relevant chipset functions Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt System Agent SA Configuration Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc VT d Enables the VT d function on MCH 46 O Chapter 3 BIOS Setup www dfi com Graphics Configuration DVMT Pre Allocated This field configures the graphics settings Selects DVMT 5 0 Pre Allocated Fixed Graphics Memory size used by the Internal Graphics Device Please refer to the screen shown below Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Primary Display DVMT Pre Allocated 32M 64M DVMT Pre Allocated 96M 128M 160M 192M 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M 1024M Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Primary Display Auto When the system boots it will automatically detects the display device DVMT Total Gfx Mem I GFX When the system boots it will first initialize the onboard VGA PEG When the syst
61. me process of closing files applications and operating system This is because the system is capable of storing all programs and data files during the entire operating session into RAM Random Access Memory when it powers off The operating ses sion will resume exactly where you left off the next time you power on the system I mportant ik The 5V standby power source of your power supply must support 2720mA Chapter 1 Introduction e Wake On PS 2 This function allows you to use the PS 2 keyboard or PS 2 mouse to power on the system I mportant The 5V standby power source of your power supply must support 2720mA e Power Failure Recovery When power returns after an AC power failure you may choose to either power on the system manually or let the system power on automatically e USB The system board supports the new USB 3 0 It is capable of running at a maximum transmis sion speed of up to 5 Gbit s 625 MB s and is faster than USB 2 0 480 Mbit s or 60 MB s and USB 1 1 12Mb s USB 3 0 reduces the time required for data transmission reduces power consumption and is backward compatible with USB 2 0 It is a marked improvement in device transfer speeds between your computer and a wide range of simultaneously accessible external Plug and Play peripherals www dfi com Chapter 2 Chapter 2 Hardware Installation Board Layout Important Electrostatic discharge ESD can damage your board processor disk drives
62. mponents IR Click Finish to complete the setup process A gs DirectX Runtime Install This install package will search for updated Direct Runtime Components and update as necessary It may take a few minutes To start installation please click Next Intel Installation Framework lt Back Cancel 3 Click Finish Reboot the Installing Microsoft R DirectX R system for DirectX to take Installation Complete effect The components installed are now ready for use Chapter 4 Supported Software www dfi com Chapter 4 Intel HD Graphics Drivers For Windows XP To install the driver click Intel HD Graphics Drivers on the main menu 1 To start installation click intwi Graphics Media dcosterator Driver Next Intel Graphics Media Accelerator Driver Welcome to the Setup Program This shun pogan wall inctali Ehe fallssing components Intel Graphics Media facoslerator Drover Rie strongly recommended that you edt all programs before continuing Chek Nest bo conbinus 2 Read the license agreement Intel Graphics Media Accelerator Driver then click Yes Intel Graphics Media Accelerator Driver intel License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHY ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLIMG OR LISING
63. n Wait for a few seconds and set JP9 back to its default setting pins 1 and 2 On 3 Now plug the power cord and power on the system Chapter 2 Hardware Installation www dfi com USB Power Select 123 123 USB 8 9 1 2 On 5V 2 3 On JP4 default 5V standby i 1 1 2 On 5V default 2 3 On USB 4 5 5V standby m N CJ USB 2 3 6 7 1 2 On 5V mm GEB 1 P8 default 23 CET 2 3 On 5V standby JP4 JP5 JP6 and JP8 are used to select the power of the USB devices Selecting 5V standby will allow you to use a USB device to wake up the system I mportant If you are using the Wake On USB Keyboard Mouse function for 2 USB ports the 5V standby power source of your power supply must support 21 5A For 3 or more USB ports the 5V standby power source of your power supply must support 224A it Chapter 2 Hardware Installation Power on Select 12 3 1 2 On Power on via Power Button default 2 3 On Power on via AC power Power on via WOL after G3 Bap o am B ms mO f E a LO To power on via WOL after G3 1 Set JP10 pins 2 and 3 to On 2 Set the After G3 field to Power Off WOL 3 Set the GbE Wake Up From S5 to Enabled To power on via AC Power 1 Set JP10 pins 2 and 3 to On 2 Set the After G3 field to Power On www dfi com COM 1 COM 2 RS232 422 485 Select 6 5 4 3 2 1 5 6 On RS485 JP17
64. n about the standard package in your region please contact your dealer or sales representative Optional I tems e USB port cable e Serial ATA data cable e COM port cable e I O shield The board and accessories in the package may not come similar to the information listed above This may differ in accordance to the sales region or models in which it was sold For more information about the standard package in your region please contact your dealer or sales representative Before Using the System Board Before using the system board prepare basic system components If you are installing the system board in a new system you will need at least the following internal components e ACPU e Memory module e Storage devices such as hard disk drive CD ROM etc You will also need external system peripherals you intend to use which will normally include at least a keyboard a mouse and a video display monitor Chapter 1 Chapter 1 Introduction Specifications LGA 1150 socket for 4th Generation Intel Core processors Intel Core Intel Core Intel Core Intel Core Intel Core Intel Core Intel Core Intel Core Intel Core Intel Core i7 4790S 8M Cache up to 4 0 GHz 65W i7 4770S 8M Cache up to 3 9 GHz 65W i7 4770TE 8M Cache up to 3 3 GHz 45W i5 4590S 6M Cache up to 3 7 GHz 65W i5 4590T 6M Cache up to 3 0 GHz 35W i5 4570S
65. nables or disables these serial ports COM Change Settings Selects the 1O IRQ settings for the super I O device Parallel Port Configuration Sets the parameters of the parallel port LPT LPTE This section displays the hardware health monitor Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Parallel Port Enabled gt Smart Fan Function Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Parallel Port Smart Fan Function Enables or disables the parallel port LPT LPTE Aptio Setup Utility Copyright C 2012 American Megatrends Inc Change Settings Selects an optimal setting for the super IO device au UU Pru Device Mode Changes the mode of the printer port Version 2 15 1236 Copyright C 2012 American Megatrends Inc 40 li Chapter 3 CPU Smart Fan Control Second Super IO Configuration When this feature is set to Automatic the CPU s fan speed will rotate according to the This section is used to configure the parameters of the system second super I O chip CPU s temperature The higher the temperature the faster the speed of rotation Aptio Setup Utility Copyright C 2012 American Megatrends Inc System Smart Fan Control When this feature is set to Automatic the System s fan speed will rotate according to the System s temperatur
66. nected to these connectors Digital 1 O Connector Pins Pin Assignment Pins Pin Assignment 1 GND 2 12V 3 DIO7 4 12V 5 DIO6 6 GND 7 DIO5 8 5V 9 DIO4 10 5V 11 DIO3 12 GND 13 DIO2 14 5V_Standby 15 DIO1 16 5V_Standby 17 DIOO 18 GND 19 GND 25 www dfi com Chapter 2 Hardware Installation Chapter 2 Cooling Fan Connectors O CPU Fan coy EE Ground Speed 1 3 idi Control System Fan ense gem m These fan connectors are used to connect cooling fans The cooling fans will provide adequate airflow throughout the chassis to prevent overheating the CPU and system board components BI OS Setting The Advanced menu PC Health Status submenu of the BIOS will display the current speed of the cooling fans Refer to chapter 3 for more information Chapter 2 Hardware Installation Power Connectors E Ground 12V GND 45V 45V 45V 5V GND GND GND PS ON GND 12V 43 3V ama e O m EE Om m INNEN Use a power supply that complies with the ATX12V Power Supply Design Guide Version 1 1 An ATX12V power supply unit has a standard 24 pin ATX main power connector that must be inserted into the 24 pin connector The 8 pin 12V power connector enables the delivery of more 12VDC current to the processor s Voltage Regulator Module VRM The power connectors from the power supply unit are designed to fit the 24 pin and 8 pin connectors in only one orientation
67. nections InstallShield Wizard tion dick Finish InstallShield Wizard Completed WARNING This program is protected by copyright law and international treaties To access new Features open Device Manager and view the properties of the network adapters i DFI Utility InstallShield Wizard 2 Click accept the terms in the license agreement then License Agreement InstalsShiiid I i II click Next Please read the following license agreement carefully To add your own license text to this dialog specify your license agreement file in the Dialog editor 1 Navigate to the User Interface view 2 Select the LicenseAgreement dialog 3 Choose to edit the dialog layout 4 Once in the Dialog editor select the Memo ScrollableText control 5 SetFileName to the name of your license agreement RTF file After you build your release your license text will be displayed in the License Agreement dialog accept the terms in the license agreement Print Ido not accept the terms in the license agreement oce Installshield Chapter 4 Supported Software www dfi com Chapter 4 3 Click Install to begin the jig DFI Utility InstallShield Wizard E lt The DFI Utility icon will appear on the desktop Double click the icon to open the utility installation Ready to Install the Program The wizard is ready to begin installation HD62
68. o protect the CPU socket against dust and harmful particles Remove the protective cap only when you are about to install the CPU I mportant The CPU socket must not come in contact with anything other than the CPU Avoid unnecessary exposure Remove the protective cap only when you are about to install the CPU Protective cap 4 Unlock the socket by push ing the load lever down moving it sideways until it is released from the reten tion tab then lift the load lever up Retention tab Chapter 2 Hardware Installation www dfi com 7 Insert the CPU into the socket The gold triangular mark on the CPU must align with the corner of the CPU socket shown on the photo Gold triangular mark The CPU s notch will at the same time fit into the socket s alignment key Alignment key I mportant The CPU will fit in only one orientation and can easily be inserted without exerting any force Chapter 2 Hardware Installation Close the load plate then push the load lever down While closing the load plate make sure the front edge of the load plate slides under the retention knob Hook the load lever under the retention tab Retention knob Retention tab www dfi com I nstalling the Fan and Heat Sink 4 Rotate each push pin ac cording to the direction of The CPU must be kept cool by using
69. oard Mouse Power Select uesueeseueeseeeeeeeeeeeeenen enne 15 USB Power Select usce Copa psu cipi nod tecum E ERES pot rtoluma Fetud bad ee as Cd 16 Appendix C Troubleshooting mm m mrm m a 78 2 2 ga aile 2 src 16 COM COM 2 RS232 422 485 Select seeeeeeerensnennenneeeenreenrensennrenneeneennse 17 COM 1 COM 2 RS232 Power Select e roeer cerent rna rra nena nr n ra ces 18 SATA DOM Power Select aeree reete terra nrt nne eani uu nu RRXSexmekxSR EISE E RE DPEEDE RENE 18 Digital 1 0 Power Select usiexesosxekbukk urb Rd RES RAEERAME FE LER YR AUGE ROG PER E XD E AUDI QURE Ea a ic 19 Digital 1 0 Outbut SESS ce GH pere DUE PRUECRER OE STER NIBH RUPES alam ORARIO aij eI Rb 19 Rear Panel 1 O Ports essesessseeeeeeeneeee nennen nnn nnne nnns 20 P5 2 Keyboad Motise POFLE cusa ukxkaek bon OO Cen EX EUH EO A ACER ARRA EN han NU Rae UR 20 COM Serial POMS s cssc aaa rae pex Ra ap x S Da racio p qa aod sciat c D ab DE 21 Graphics THIESETOCBIS esie a E Rabe ord eE Ed Or rS OY REOR SA eater dn OE 22 RJ45 IAN PONS uoiaripiioedeturcieie innin ne a ah OE pais oir ana c cu E sula equals AL EEE EE Oni MM ha 22 USB mel eee ee ee ee eT ee Ter 23 About this Manual An electronic file of this manual is included in the CD To view the user s manual in the CD insert the CD into a CD ROM drive The autorun screen Main Board Utility CD will appear Click User
70. ode of XHCI controller These options are Auto Enabled and Disabled When Disabled is selected in the XHCI Mode it will display the following Aptio Setup Utility Copyright C 2012 American Megatrends Inc information Aptio Setup Utility Copyright C 2012 American Megatrends Inc USB Precondition Disabled XHCI Mode Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc USB Precondition T EHCI 1 and EHCI 2 Precondition works on USB host controller and root ports for faster enumeration These fields are used to control the functions of USB EHCI USB 2 0 controllers One EHCI controller must always be enabled 53 Chapter 3 BIOS Setup www dfi com Chapter 3 USB Ports Per Port Disable Control PCH Azalia Configuration This field is used to control each of the USB ports 0 13 disabling When enabled This field is used to configure the PCH Azalia settings it will display the following information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc USB Ports Per Port Disable Control Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc USB Port 0 1 2 3 4 5 8 9 10 11 Enables or disables these USB ports 52 Chapter 3 BIOS Se
71. on the system board Mounting hole 3 Orient the heat sink such CPU Fan connector that the CPU fan s cable is nearest the CPU fan con nector Chapter 2 Hardware Installation www dfi com Jumper Settings PS 2 Keyboard Mouse Power Select Clear CMOS Data 123 1 2 On 5V default L23 CIO 2 3 On 5V standby 2 2 1 1 2 On Normal default 3 2 1 2 3 On Clear CMOS Data If you encounter the followings JP1 is used to select the power of the PS 2 keyboard mouse port Selecting 5V_standby will allow you to use the PS 2 keyboard or the PS 2 mouse to wake up the system a CMOS data becomes corrupted b You forgot the supervisor or user password I mportant you can reconfigure the system with the default values stored in the ROM BIOS ik The 5V_standby power source of your power supply must support gt 720mA To load the default values stored in the ROM BIOS please follow the steps below 1 Power off the system and unplug the power cord 2 Set JP9 pins 2 and 3 to O
72. on www dfi com The system board supports the following memory interface Single Channel SC Data will be accessed in chunks of 64 bits 8B from the memory channels Dual Channel DC Data will be accessed in chunks of 128 bits from the memory channels Dual channel provides better system performance because it doubles the data transfer rate DIMMs are on the same channel DIMMs in a channel can be identical or Single Channel completely different However we highly recommend using identical DIMMs Not all slots need to be populated Dual Channel DIMMs of the same memory configuration are on different channels Chapter 2 Hardware Installation I nstalling the DI MM Module Note itk The system board used in the following illustrations may not resemble the actual board These illustrations are for reference only 1 Make sure the PC and all other peripheral devices connected to it has been powered down Disconnect all power cords and cables Locate the DIMM socket on the system board Emo qe wN Push the ejector tabs which are at the ends of the socket to the side Ejector tab Ejector tab www dfi com Grasping the module by its edges position the module above the socket with the notch in the module aligned with the key on the socket The keying mechanism ensures the module can be plugged into the socket in only one way 7 Seat the module vertically pressing it down
73. onfiguration lt F3 gt Optimized defaults Most of the configuration settings are either predefined according to the Load Optimal Defaults lt F4 gt Saves and resets the setup program settings which are stored in the BIOS or are automatically detected and configured without mean requiring any actions There are a few settings that you may need to change depending on Enter Press lt Enter gt to enter the highlighted submenu your system configuration Entering the BIOS Setup Utility Scroll Bar The BIOS Setup Utility can only be operated from the keyboard and all commands are key When a scroll bar appears to the right of the setup screen it indicates that there are more board commands The commands are available at the right side of each setup screen available fields not shown on the screen Use the up and down arrow keys to scroll through all the available fields The BIOS Setup Utility does not require an operating system to run After you power up the system the BI OS message appears on the screen and the memory count begins After the Submenu memory test the message Press DEL to run setup will appear on the screen If the message disappears before you respond restart the system or press the Reset button You may also i When appears on the left of a particular field it indicates that a submenu which contains restart the system by pressing the lt Ctrl gt lt Alt gt and lt Del gt keys simultaneously additional options are avai
74. parameters Aptio Setup Utility C right C 2012 Ameri Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc BOO Be eas OP YE SQ ara ae gt PCI Express Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Onboard 1217 LAN Controller Enables or disables the onboard 1217 LAN controller Onboard 82574 LAN Controller Enables or disables the onboard 82574 LAN controller High Precision Timer Enables or disables the High Precision Event Timer 49 Chapter 3 BIOS Setup www dfi com PCI Express Configuration This field is used to configure the PCI Express settings Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc PCI Express Root Port 3 Enabled gt PCI Express Root Port 1 Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc PCI Express Root Port 1 and 3 Controls the PCI Express Root Port Aptio Setup Utility Copyright C 2012 American Megatrends Inc PCIe Speed Version 2 15 1236 Copyright C 2012 American Megatrends Inc PCle Speed Selects the speed of PCI Express port Auto Gen 1 or Gen 2 50 Chapter 3 USB Configuration XHCI Mode This field is used to configure the USB settings Selects the operation m
75. re bo caraid need arei rdarstarsd all Ehe raghbs and nimilrichors dascritsid in lhe Ene ene OEE eee ai icense tems You must accept the license terms before vou carta tha software ment then click Install MICROSOFT SOFTWARE SUPPLEMENTAL LICENSE TERMS Press thee Page Doan key bases more beset CE E hare read and ACCEPT tha bera oF the Liceras fugerent COE OO NOT ACCEPT the terms of Ehe License Agreement LL Send information about my setup Detail regarding the ias col 60 mg Zhe 27 min 56 kbps L min 512 kbps 2 Setup is now installing the driver Chapter 4 Supported Software www dfi com Chapter 4 3 Click Exit ME Microsoft NET Framework 3 5 Setup x Intel Chipset Software Installation Utility The Intel Chipset Software Installation Utility is used for updating Windows INF files so that the Intel chipset can be recognized and configured properly in the system Microsolt SET Framework 3 5 has been installed successfully dp F i high recommended that you dowmload and natal the latest service packs and secunty To install the utility click Intel Chipset Software Installation Utility on the main menu 1 Setup is ready to install the Intel Chipset Device Software utility Click Next Intel Chipset Device Software Welcome to the Setup Program This setup program will install the Intel Chipset Device Software onto this computer It is strongly recommended that you exit all programs befor
76. re the add in card is seated securely in the expansion slot If the add in card is loose power off the system re install the card and power up the system 1 Make sure the correct drive type for the hard disk drive has been entered in the BIOS 2 Check the jumper settings to ensure that the jumpers are properly set 2 f the system is configured with two hard drives make sure the bootable first hard drive is configured as Master and the second hard drive is configured as Slave The master hard drive must have an active bootable partition 3 Verify that all memory modules are seated securely into the memory sockets 4 Make sure the memory modules are in the correct locations Excessively long formatting period 5 f the board fails to function place the board on a flat surface and seat all socketed com MM ponents Gently press each component into the socket If your hard drive takes an excessively long period of time to format it is likely a cable con nection problem However if your hard drive has a large capacity it will take a longer time to 6 If you made changes to the BIOS settings re enter setup and load the BIOS defaults format Serial Port The serial device modem printer doesn t output anything or is outputting garbled characters l Make sure that the serial device s power is turned on and that the device is on line 2 Verify that the device is plugged into the correct serial port on the rear of the computer
77. splays minutes from OO to 59 Second displays seconds from OO to 59 33 i Chapter 3 BIOS Setup www dfi com Chapter 3 ACPI Power Management Configuration Trusted Computing This section is used to configure the ACPI Power Management This section configures settings relevant to Trusted Computing innovations Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Security Device Support Disable Resume by PME Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Security Device Support Resume by PME This field is used to enable or disable BIOS supporting for the security device O S will not show the security device TCG EFI protocol and INT1A interface will not be Enables this field to use the PME signal to wake up the system available Resume by Ring Enables this field to use the Ring signal to wake up the system Resume by RTC Alarm When Enabled the system uses the RTC to generate a wakeup event Wakeup Event After G3 This field is used to enable or disable the specific wakeup event after G3 It needs to switch the hardware jumper for AC power on to the proper setting 34 Chapter 3 BIOS Setup www dfi com Chapter 3 CPU Configuration SATA Configuration This section is use
78. stalling Intel ME FW Recovery Agent Copying File C Program Files Intel Intel R Management Engine Components Firmware Re Click Next to continue m 4 r Intel Installation Framework 4 After completing installa tion click Finish it ani ad Intel Management Engine Components Setup Is Complete The setup program successfully installed the following components frie iy a aS Intel Dynamic Application Loader Intel Identity Protection Technology Intel IPT Serial Over LAN Intel Management and Security Status Click Finish to complete the setup process Intel Installation Framework Chapter 4 Supported Software www dfi com Chapter 4 Audio Drivers Intel LAN Drivers For Windows XP To install the driver click Audio Drivers on the main menu The LAN drivers for Windows XP supporting on the HD620 H81 system board has to be installed manually When you want to install the LAN driver for Windows XP please follow the l Setup is ready to install the steps below to accomplish the installation driver Click Next E Computer Management Fie Action View Window Heip e OMT IMARA 1 Launch the Hardware Update Wizard for the selected device Select JN Computer Management Local E rercireEsvEES Update Driver e Tools ie M Computer LUIS bo the ciel heel Sore lim ID WS LESIIEUILI Event Viewer oS Disk dives i a Shared Folders
79. t and mic in jacks that are at the front panel of your system Driver Installation Install the audio driver Refer to the chapter 4 for more information Chapter 2 Hardware Installation I O Connectors SATA Serial ATA Connectors E OQczozaea SASE G SATA 3 0 6Gb s SATA port 1 provides adequate space for SATA DOM SATA 5 SATA 4 SATA 2 0 3Gb s Features e 4 Serial ATA ports 2 SATA 3 0 ports with data transfer rate up to 6Gb s SATA 0 and SATA 1 2 SATA 2 0 ports with data transfer rate up to 3Gb s SATA 4 and SATA 5 e Integrated Advanced Host Controller Interface AHCI controller The Serial ATA connectors are used to connect Serial ATA devices Connect one end of the Se rial ATA data cable to a SATA connector and the other end to your Serial ATA device www dfi com BIOS Setting Digital O Connector Configure the Serial ATA drives in the Advanced menu SATA Configuration submenu of the BIOS Refer to the chapter 3 for more information Note Some 3rd party SATA Gen 2 speed device controllers used on the system board paired with the Intel 8 series chipset are intermittently detected Before using SSD devices or mSATA SSD devices please check whether the device and the cable which are used on the system board conform to Intel s official regulations i Digital 1 0 The 8 bit Digital I O connector provides powering on function to external devices that are con
80. this 1accept the terms in the license agreement O1 do not accept the terms in the license agreement Installshield Intel R Network Connections Setup Options Select the program Features you want installed Install F Drivers Intel R PROSet For Windows Device Manager v Advanced Network Services E InteR Network Connections SNMP Agent Feature Description Chapter 4 Supported Software www eco aa Chapter 4 4 Click I nstall to begin the l3 Intel R Network Connections InstallShield Wizard ud DFI Utility i nstal lation Ready to Install the Program inteD The wizard is ready to begin installation inte DFI Utility provides information about the board Watchdog and DIO To access the utility click DFI Utility on the main menu Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard Note If you are using Windows 7 you need to access the operating system as an administrator to be able to install the utility 1 Setup is ready to instal iz DFI Utility InstallShield wee m the DFI Utility driver Welcome to the InstallShield Wizard for DFI InstallShield a ee Cl ick Next The InstallShield R Wizard will install DFI Utility on your computer To continue click Next 5 After completing installa ie Intel R Network Con
81. tinue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software a Intel amp Installation Framework Chapter 4 3 Go through the readme docu ment for more installation tips then click Next 4 Setup is currently installing the driver After installation has com pleted click Next 5 After completing installation click Finish e Tm m USB 3 0 eXtensible Host Controller Driver intel Readme File Information Refer to the Readme file below to view the system requirements and installation information Intel R USB 3 0 eXtensible Host Controller 1 0 1 209 bee January 2012 NOTE This document refers to systems containing the bad following Intel processors chipsets Intel Installation Framework peus R USB 3 0 eXtensible Host Controller Dres intel Setup Progress Please wait while the following setup operations are performed Program Files x85
82. tional treaties Adobe Change Destination Folder lt Back 2 Click Install to begin installa i Adobe Reader 9 3 Setup tion ys Ready to Install the Program Click Install to begin the installation If you want to review or change any of your installation folder click Back Click Cancel to exit setup 3 Click Finish to exit installation FRR his Setup Completed Setup has successfully installed Adobe Reader 9 3 Click Finish to exit setup Cancel Chapter 4 Supported Software www dfi com Chapter 5 Digital 1 O Programming Guide Register Description The Input Port Register register O reflects the incoming logic levels of the pins regard less of whether the pin if defined as an input or output by the Configuration Register They act only on the red operation Writes to this register have no effect The default value X is determined by the externally applied logic level Before a red operation a write transmission is sent with the command byte to indicate to the I C device that the Input Port Regiser will be accessed next Register O Input Port Register The Onput Port Register register 1 shows the outgoing logic levels of the pins defined as outputs by the Configuration Register Bit values in this register have no effect on pins defined as inputs In turns reads from this register reflect the value that is in the flip flop contolling the output selection not the ac
83. to meet business needs It provides excellent video and 3D graphics with out standing graphics responsiveness These enhancements deliver the performance and compat ibility needed for today s and tomorrow s business applications Supports VGA and DVI D inter faces for display outputs e PCI Express PCI Express is a high bandwidth I O infrastructure that possesses the ability to scale speeds by forming multiple lanes The x4 PCI Express lane supports transfer rate of 4 Gigabyte per second 2 directions The PCI Express architecture also supports high performance graphics infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB s bandwidth 8GB s in each direction e Serial ATA Serial ATA is a storage interface that is compliant with SATA 1 0a specification With speed of up to 3Gb s SATA 2 0 and 6Gb s SATA 3 0 it improves hard drive performance faster than the standard parallel ATA whose data transfer rate is 100MB s The bandwidth of the SATA 3 0 will be limited by carrier board design e Gigabit LAN One Intel 82574 PCI Express Gigabit Ethernet controller and one Intel I217 Gigabit Ethernet Phy support up to 1Gbps data transmission HD620 H81B supports one Intel 82574 PCI Express Gigabit Ethernet controller only e Audio The Realtek ALC886 audio codec provides 5 1 channel High Definition audio output Chapter 1 Introduction www dfi com e Wake On LAN This feature allows the network to remotely wak
84. trends Inc Save Changes and Reset Administrator Password Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Save Changes and Reset Administrator Password To save the changes select this field and then press lt Enter gt A dialog box will Sets the administrator password appear Select Yes to reset the system after saving all changes made User Password Discard Changes and Reset Sets the user password To discard the changes select this field and then press lt Enter gt A dialog box will appear Select Yes to reset the system setup without saving any changes Restore Defaults To restore and load the optimized default values select this field and then press lt Enter gt A dialog box will appear Select Yes to restore the default values of all the setup options Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shellx64 efi from one of the available filesystem devices 54 Chapter 3 BIOS Setup www dfi com Chapter 3 Updating the BI OS Notice BIOS SPI ROM To update the BIOS you will need the new BIOS file and a flash utility AFUDOS 1 The Intels Management Engine has already been integrated into this system board Due to EXE Please contact technical support or your sales representative for the files the safety concerns the BIOS SPI ROM chip cannot be removed from this system board an
85. tual pin value Register 1 Onput Port Register The Polarity Inversion Register register 2 allows polarity inversion of the pins defined as inputs by the Configuration Register If a bit in this register is set written with 1 the cor responding port pin s polarity is inverted If a bit in this register is clear written with a O the corresponding port pin s original polarity is retained Register 2 Polarity Inversion Register Chapter 5 Digital I O Programming Guide The Configuration Register register 3 configures the direction of the I O pins If a bit in this register is set to 1 the corresponding port pin is enabled as an input with a high impedence output driver If a bit in this register is cleared to O the corresponding port is enabled as an input Register 3 Configuration Register www dfi com Function Description I 2CWriteByte SlaveAddr SubAddr Data Write a Byte data to a specified 12C Device 2CReadByte SlaveAddr SubAddr Data Read a Byte data from a specified 12C Device SetBit Data Bit Set Data bit n as 1 CIrBit Data Bit Set Data bit n as O GetBit Data Bit Return the value of data bit n Sample Code GPI O Configuration define SLAVE _ ADDR 0x42 define INPUT PORT OxOO define OUTPUT PORT OxO1 define INVERSION PORT 0x02 define COMFIG PORT 0x03 GpioConfig int PinNum int Mode 1 BYTE Data BYTE TempPinNum PinNum 68 PinO 7 Input Output Con
86. tup www dfi com Chapter 3 Boot CSM Parameters SN p ING P z Aptio Setup Utility Copyright C 2012 American Megatrends Inc A ea U ey TS AD I ES Launch CSM Enabled Setup Prompt Timeout Version 2 15 1236 Copyright C 2012 American Megatrends Inc Version 2 15 1236 Copyright C 2012 American Megatrends Inc Setup Prompt Timeout Boot option filter This option controls what devices system can be boot to Selects the number of seconds to wait for the setup activation key 65535 OxFFFF P y denotes indefinite waiting Launch PXE OpROM policy Bootup NumLock State Controls the execution of UEFI and legacy PXE OpROM This allows you to determine the default state of the numeric keypad By default the Launch Storage OpROM policy system boots up with NumLock on wherein the function of the numeric keypad is the number keys When set to Off the function of the numeric keypad is the arrow keys Controls the execution of UEFI and legacy storage OpROM Quiet Boot Other PCI device ROM priority For PCI devices other than Network Mass Storage or Video defines which Enables or disables the quiet boot function OpROM to launch 53 li Chapter 3 BI OS Setup www dfi com Chapter 3 Security Save amp Exit Aptio Setup Utility Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Mega
87. u Super IO Configuration submenu of the BIOS Refer to the chapter 3 for more information Note 1 HD620 H81X 10 COM COM 1 to COM 10 HD620 H81B D 2 COM COM 1 and COM 2 2 When COM 1 RS232 422 485 is selected JP17 and JP18 must be set in accordance to JP2 3 When COM 2 RS232 422 485 is selected JP19 and JP20 must be set in accordance to JP16 f P2 a8 Yylk6Ba COM 7 COM 8 vrg Das COM 7 COM 8 RS232 www dfi com Graphics I nterfaces RJ 45 LAN Ports The display ports consist of the following e 1 VGA port e 1 DVI D port LAN 1 LAN 2 LAN 1 LAN 2 Features e Intel 82574 PCI Express Gigabit Ethernet controller e Intel I217 Gigabit Ethernet Phy HD620 H81X D ico had The LAN ports allow the system board to connect to a local area network by means of a The VGA port is used for connecting a VGA monitor Connect the monitor s 15 pin D shell cable network hub connector to the VGA port After you plug the monitor s cable connector into the VGA port gently tighten the cable screws to hold the connector in place BI OS Setting DVI D Port Configure the onboard LAN ports in the Chipset menu PCH IO Configuration submenu of the BIOS Refer to the chapter 3 for more information The DVI D Digital Visual Interface port is used to connect a digital LCD monitor or LCD TV Connect the display device s cable connector to the DVI D port at location CN13 Aft
88. ww dfi com Chapter 2 LPC Debug Port SMBus Connector NC 9 SMB ALERT SMB_DATA iE SMB CLK GND DE 3 3V_ Standby mus IE 21 C men aa The SMBus System Management Bus connector is used to connect the SMBus device It is a multiple device bus that allows multiple chips to connect to the same bus and enable each one The LPC connector is used for the debug function and its pin functions are listed below to act as a master by initiating data transfer Pins Pin Assignment Pins Pin Assignment 1 CLK 2 LAD1 3 RST 4 LADO 5 FRAME 6 VCC_ 3V 7 LAD3 8 GND 9 LAD2 10 X 11 SERIRQ 12 48MHz 30 www dfi com Chapter 2 Hardware Installation Chapter 2 LAN LED Connector The LAN LED connector is used to detect the connection state of RJ45 LAN ports when the connection is made to an active network via a cable The pin functions of the LAN LED con nector are listed below Pins Pin Assignment Pins Pin Assignment 1 Link Activity 2 3V standby 3 GLED LED 1000 4 GLED LED 100 5 Link Activity 6 3V standby 7 GLED LED 1000 8 GLED LED 100 Chapter 2 Hardware Installation Battery Battery The lithium ion battery powers the real time clock and CMOS memory It is an auxiliary source of power when the main power is shut off Safety Measures e Danger of explosion if battery incorrectly replaced e Replace only with the same or equivalent type recommend by the manufacturer e Dispose of used batteries accor
89. xt to continue Install Intel Control Center Intel Control Center provides a centralized starting point for Intel applications making it easier to find the programs that you need lt Back Intel Installation Framework Intel Rapid Storage Technology Warning The Intel Rapid Storage Technology driver you are about to install may be used to control the hard drive that this computer boots from or to control a hard drive that contains important data Therefore you will not be able to uninstall this driver after installation However you will be able to uninstall the non critical components of this software such as the User Interface Event Monitor Service and program shortcuts Click Next to continue or dick Cancel to exit the setup program Intel Installation Framework 3 Read the license agreement then click Yes 4 Go through the readme document for system requirements and instal lation tips then click Next 5 Setup is now installing the utility Click Next to continue Chapter 4 Supported Software www dfi com lt ie Intel Rapid Storage Technology intel License Agreement You must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms INTEL SOFTWARE LICENSE AGREEMENT OEM IHV ISV Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load th

Manual - DFI Inc.

Contents

Download Pdf Manuals

Related Search

Related Contents