PRODUCT FACT SHEET FM300 Communicator Overview FEATURES
Contents
1. 500mA Signaling device This interface allows the user to make voice calls using a headset keypad and cable GSM GPRS Antennae GPS Antennae Main harness with integrated buzzer 2x frequency input 3x digital analogue FM300 code plug harness including vehicle interface Blue driver s plug driver log on FM on board computer user manual Optional harnesses I O harness 2x frequency input 4x digital analogue input serial harness voice harness input TECHNICAL DESCRIPTION Voltage range Input Protection Clock Inputs events amp outputs Firmware 8 analogue inputs Frequency measurement Frequency inputs Relays Buzzer and LED lC Bus TTL level serial port Memory 9VDC 33 VDC Automotive 24V load dump 160V 2 Ohm 400mS short duration low energy amp high energy transients Real time with independent battery back up Highly configurable inputs events and output control Re programmable firmware and configuration over wired and wireless media 8 analogue lines measuring voltages in the range of 0 38 volts in steps of approximately 0 15 volts These inputs can be programmed to measure voltages between 0 and 5 volts in increments of approximately 0 02 volts A selected analogue input can measure frequencies of up to 150Hz or low board rate encoded RS232 inputs up to 75 baud 4 high frequency inputs one dedicated to measuring engine RPM and another to measuring Vehicle Road S2. TELEMATICS MOBILE INFORMATION EXCHANGE WU PRODUCT FACT SHEET FM300 Communicator Overview The FM300 Communicator offers the same extensive driver and vehicle management as the FM200 Plus and has an additional internal GPS receiver and GSM GPRS modem The GPS receiver allows the recording of GPS position information The GPS receiver combined with the GSM GPRS modem allow for active tracking of vehicles and enables real time notifications of user specified events as well as over the air re configuration of on board computers and the downloading of data FEATURES ACTIVE TRACKING Active Passive Tracking Request the vehicle position in real time or view the route taken after the trip has been or Active Trail downloaded Active Trail allows hourly updating of the Fleet Manager software with GPS vehicle positions Various information is recorded with every GPS point e g vehicle and driver ID date and GESIDAtIRECOrdiNg time latitude and longitude altitude heading velocity number of satellite etc Manage Locations Add any desired location such as customer supplier or no go zones Plan routes by entering stops start times and duration of each stop This can serve as daily Toue Pennine job activity sheets for your drivers Receive data messages such as SMS when selected standard or user defined events Active Events ae occur e g a cargo door opening in a no go zone driver arrived at customer loca
3. acement for RAM Page 2 of 4 www mixtelematics com TECHNICAL SPECIFICATIONS ENVIRONMENT Storage 20 to 70 C non battery backup Temperature Operating 10 to 70 non battery backup Circuit protection Conformal coating over the PCB and all components excluding connectors SUPPLY Operating lt 42mA at 28V typical Sleep lt 20mA at 28V typical Operating lt 70mA at 12V typical Sleep lt 30mA at 12V typical Powered down lt 2mA at 12V typical Powered down lt 3mA at 28V typical The signal strength on the GSM affects the current consumption The firmware running on the FM300 Communicator micro processor affects the current consumption of the unit Current RELAY CIRCUIT Current Specifications 200mA typical Maximum continuous 33V voltage on pin Protection Voltages of 36V and higher will be clamped by tranzorb RS202 PORTS Maximum Speed 57600 Baud higher rates possible with hardware flow control Protection transient 15Kv as per human body model Protection DC OV to 12V IC BUS Normal operating speed 38Kbits per second Maximum supply current lt 20MA CLK Protection transient 15Kv as per human body model Protection DC OV to 12V REAL TIME CLOCK Time Loss lt 10 Minutes per year Typical lt 5 seconds when a GPS is used auto synchronization gt 5 Years typical at 30 to 70 C Battery backupilife temperature change affects
4. econd RS232 Port S2 is connected to the internal GSM GPRS Modem Page 4 of 4
5. peed The 3 and 4 inputs were originally dedicated to measuring user defined inputs especially those from fuel measuring devices i e EDM s The 3 frequency input can be used to input NMEA strings from the GPS receiver These inputs work to approximately 5KHz RPM amp Speed and 12KHz F3 amp F4 The FM300 Communicator features 2 150mA open collector output drivers for driving a relay One relay can be used to switch off peripheral devices such as GPS The FM300 Communicator has a buzzer and LED to warn the driver and to provide feedback of the vehicle s status Intended for use with code plugs used to identify drivers calibrate diagnose faults upload firmware and new configurations and to download logged data and unit specific configuration information This bus can also be used to drive a simple icon based Fleet Log Book which displays driving reasons violations and faults and can allow the driver to make voice calls Intended to be used by devices designed to work on a bus The bus was specified to be a Multi Master type to enable other intelligent devices to optionally work as master relieving the FM300 Communicator of processing Memory is limited to 1 megabyte of flash and 20Kb s of RAM 196Kb s of flash memory is dedicated to storing firmware 128KB for tacho data 312 KB for event data and the remaining 384KB for buffering data and non volatile temporary memory space A FRAM is also present as a non volatile repl
6. the accuracy of the RTC crystal it s most accurate at 25 C Channels 16 Update rate 1Hz Accuracy position 2 5m CEP Accuracy DGPS SBAS 2 0m CEP Start up time lt 2minutes GPS operating 40 C to 85 C temperature GPRS Multi slot class 10 Triple band EGSM900 DSC1800 PSC1900 Transmit power Operating temperature SIM Card www mixtelematics com For voice data text messages SMS and Fax Class 4 2W for EGSM900 Class 1 1W for DSC1800 PCS1900 20 C to 55 C 25 C to 70 C limited functionality 3V AUXILLIARY INPUTS OUTPUTS 8 configurable analogue or digital inputs 4 auxiliary frequency input 2 Auxiliary relay drive 3 Serial interface 2x RS232 and 1x TTL The FM300 Communicator analogue or digital inputs can be configured to configured to monitor any device that generated a change in voltage e g seat belts headlights refrigeration units emergency lights doors PTO UDS trailer coupling etc The FM300 Communicator auxiliary frequency input can be configured to monitor any device that generates a change in frequency e g temperature sensor liquid flow measurement or as a pulse counter e g electronic fuel consumption measurement EDM A fourth auxiliary input F3 is connected to the internal GPS receiver This can be used to switch a relay with a current consumption of up to 150 mA This can be connected to any TTL or RS232 serial device using the FM Serial cable e g FM Terminal A s
7. tion COMMUNICATIONS Downloading to Use the GSM GPRS Modem to download data to and upload data from the FM300 uploading from vehicle Communicator The modem also enables active tracking of the FM300 Communicator by the FM Software Voice Calls Incoming voice calls are possible with an optional headset VEHICLE AND DRIVER MANAGEMENT The following data is recorded date and time distance traveled journey duration vehicle Trip Data Recording speed engine speed RPM journey departure and arrival time driver name driver ID vehicle ID The following standard violations are recorded over speeding over revving green band Eri MiolaBous driving harsh braking harsh acceleration excessive idling and overtime driving Customised Events Define customized events such as driver door opening no go zone entered hazard lights activated and refrigerator temperature exceeded Second to Second Tacho The status of inputs such as speed and RPM is recorded every second This provides Data valuable in depth information for accident analysis Servicing and Licensing Set reminders for your vehicle s next service or vehicle driver license expiry www mixtelematics com Page 1 of 4 www mixtelematics com GENERAL INFORMATION Ignition input Positive drive output Buzzer output Audio interface FM300 Communicator Includes Used to monitor the ignition switch status Used to power external devices It can supply current up to
Download Pdf Manuals
Related Search