Home

CAN Connect User`s Manual

1. Oy HMI SYSTEMS CAN Connect User s Manual Rev 2 2 20 2012 CAN Connect User s Manual Index Chapter 1 Installation pg 3 1 1 Windows XP Windows 7 1 2 USB Connection Chapter 2 Interface pg 5 2 1 CAN Connect Toolbar 2 2 Main Transmission Workspace Chapter 3 The Modules pg 13 3 1 482CRM Interface 3 2 521CRED Interface 3 3 524AM Interface 3 4 540SIM Interface 3 5 541CEl Interface Chapter 4 Tutorials pg 32 4 1 521CRED 4 2 524AM 4 3 482CRM 4 4 540SIM 4 5 541CEl 4 6 Post Test Setup Optional Chapter 5 Error Messages pg 43 5 1 Error Message Table 5 2 Error Information Chapter 1 Installation 1 1 Windows XP Windows 7 Once HMI Systems has provided your CAN Connect install file follow the steps below to install the software onto your computer 1 First locate your setup exe file Double click the file to start installation If asked by windows to allow file to continue click yes 2 The CANcreate Software Suite window should show up Read the License Agreement and if you accept it then click Install 3 When completed the message Installation completed successfully should be in the message window Locate the CANconnect icon on your desktop to launch the software CANcreate Software Suite Setup v2 5 1 N Close Close Please close all other applications before continuing with install Please close al
2. CAN Connect Toolbar File Tools Advanced New Open Save Save As Recent File Close TOUTE Tm New Open new ccn file Open Open previously created ccn file Save Save current ccn file Save As Save current ccn to specified location Recent File Open recently used files Close Close window 2 1 CAN Connect Toolbar Tools Advanced Options Help Clear Messages Read Serial Number Write Serial Number Open Boot Loader Open 482CRM Interface Open 521CRED Interface Open 524AM Interface Open 529BIB Interface Open 531CRM Interface Open 540SIM Interface Open 541CEI Interface Clear Messages Clear the messages in the Message section Read Serial Number Read in the selected module serial number Write Serial Number Create and write a new serial number for the selected module Open Boot Loader Use to update module firmware Open 482CRM Interface Open 482CRM editing interface window Open 521CRED Interface Open 521CRED editing interface window Open 524AM Interface Open 524AM editing interface window Open 529BIB Interface Open 529BIB editing interface window Open 531CRM Interface Open 531CRM editing interface window Open 540SIM Interface Open 540SIM editing interface window Open 541CEI Interface Open 541CEI editing interface window 2 1 CAN Connect Toolbar Advanced Options Help View Module Details De
3. Close window Tools Open Diagnostics Window Tests to verify components are working correctly Open Burn In Window Factory use only Read Diagnostics Factory use only Rotate Switch 180 Change switch assignments from low to high byte and from high to low 13 Options Read Only Mode No editing is allowed Reverse Displayed Bit Order Changes the bit order from 0 gt 7 to 7 gt 0 482CRM Configurator v2 7 a T xE E File Tools Options Message Transmitted By Module 482CRM gt CAN Show Received Messages L Log Messages 00000000 Bytes 8 4 Period 1000 ms Minimum 100 ms NAME 1 2 3 4 5 6 7 8 O1234567012345670123A45670123 45670123 45670123 45670123A45670123 4567 oo0000000000D000DD0DDDDDDDDODDODOOODOGDAODDAODDDVDO00000000000000000000000 Message Received By Module CAN gt 482CRM oo000000 Mask 1FFFFFFE Bytes 8 Cycle Test LED On LED Off 1 2 3 4 5 6 7 8 O12345670123 45670123 45670123 45670123 45670123 4567012345670123 4567 D 0000000000000000 000000000000000000000000000000000000000000000000 Bit Selector E Colors White X Set All False X C 1 Top PO Invert oan HHH Write Verify Read Design Design Design Interrogate Disable Set to Module Config Demo Mode Sleep Mode A The Message Transmitted By Module section is where the information to be transmitted is specified The first text field includes the destination address
4. Configuration check the box to enable message 1 Set the Transmission Period to 1000ms For the Message ID write in 18EFFF96 Leave Transmit On Change unchecked Note This Message ID is for illustrative purposes only and can be set to whatever works with your system For Byte 1 use the drop down menu to select Channel 1 Low Byte Next set Byte 2 to Channel 1 High Byte In Byte 3 set it to Channel 1 Adjusted Finally in Byte 4 select Status Register For the remaining bytes set them all as Constant with 00 in each number field next to them Go to Connect and Write Design The module is now programmed OPTIONAL Follow the Post Test Setup instructions to test the newly edited 540SIM 39 4 5 541CEI Tutorial 541CEI Configurator File Tools Connect Message ID 18EFFFS7 Transmission Period 1000 ms JV Transmit On Change Minimum Period 100 ms Constant Input 1 MV Active Low Byte 1 ss Input 2 JV Active Low Byte 2 00 Input 3 MV Active Low Byte 3 o0 Input 4 V Active Low Byte 4 00 Input 5 JV Active Low Byte 5 00 Input 6 V Active Low Byte 6 00 Input 7 M Active Low Byte 7 Input 8 V Active Low Byte 8 Toggle All Note This requires a CAN USB adapter and 541CEI module 1 Connect the 541CEI module to the PC via CAN to USB adapter 2 Open CANconnect and click Request Broadca
5. alarm will be triggered The Data Bytes and Data Mask are bitwise ANDed together so a single bit in the message can be isolated to trigger the alarm Use the transmit button to send the current Message ID and Data Bytes over the CAN interface to test the alarm The drop down menu default set to alarm can change what action the message triggers Actions include disabled alarm clear and silence Disabled means the message isn t used Zo Alarm means the alarm pattern is played if criteria is matched Clear means the message clears all active alarms silences them and clears all LED if criteria is matched Silence means the message silences all active alarms if criteria is matched clears warning LED but Error LED will remain active C Checking the Enable Manual Controls box enables these testing options With a device connected the volume control can be increased and decreased in the box next to the Volume Control to test out what the appropriate volume level is for the current implementation The two LED check boxes and Switch boxes allow for testing of those functions as well Note Enable Manual Controls are software features only and don t affect the actual testing of the module D The Pattern section specifies the 64 bit configurable tone pattern to be played when the correct message is received by the module The periods inthe pattern turn the buzzer off and the lines in the pa
6. currently executing Any errors or successful read write verify messages will be shown in this message section 16 482CRM Physical Device The switches can be set up for many different uses The switch can rock up and down to be used for an increasing decreasing function Single directional rocker switch can also be used If not all switches are used a blank dummy switch can be inserted 17 521CRED Interface Cee ee e a a lf im ADJUST Close Closes the window Connect Interrogate Module Returns the device address and version information that is being edited Write Design This exports the newly created design to the device to use Verify Design This checks to make sure the design is correct on the device Read Design This imports the design that is currently stored on the device Note Bad response message may occur upon request check connections and retry Read Design Read Diagnostics Factory use only 18 521CRED Configurator v2 7 File Connect Channel Configuration Channel 1 A a B cnsnnes Channel 1 X M Channel 2 Channel 3 Minimum ie Maximum 9999 Decimal 0 V Rollover Channel 4 Message Configuration Message Message 1 x V Enabled Transmission Period 1000 ms Message ID 00000000 Transmit On Change Minimum Period 100 ms Byte 1 Channel 1 Low Byte gt oo Bytes 8 nd Byte 2 Channel 1
7. module will send the new data before the Transmission Period It will not transmit any faster than the Minimum Period The Bytes drop down menu changes the number of bytes to be looked at B This lists the inputs coming into the module Next in the Byte column each input has a drop down menu to select what byte it will be compared to Bytes 1 to 8 In the Bit column each input has a drop down menu to select which bit from the previously selected byte to use Finally the Active Low check box can be used to change from active high to active low or active low to active high The Toggle All button can be used to check or uncheck all the boxes at once 30 C Under the Constant section each Byte being used can be set using a constant By default all are set to 00 The constant value is exclusive ORed with the value detected on the input When an active high input is selected the non active result is true When the input is detected as being active high the result will be false Example Bit 0 of byte 1 is active high When the external input is pulled low bit O is 1 When the external input is pulled high bit O is 0 Writing a value of 01 to the constant field will XOR the results so that the external input pulled low equates bit 0 to O and the external input pulled high equates bit 0 to 1 D The information message section indicates what actions have occurred and may be currently executing Any errors or successful re
8. 7 8 0123456701234567012345670123456701234567012345670123456701234567 oo0o00000000000000000000000000000000000000000000000000000000000000 Message Received By Module CAN gt 482CRM 18EFFF93 Mask 1FFFFFFF Bytes 8 Cycle Test LED On LED Off 1 2 3 5 6 4 z 8 0123456701234567012345670123456701234567012345670123456701234567 Q9000000D0000000DODDDDDDODOODDDDODOOO000D0DD0DD0DD000000000000000000000000 Bit Selector Colors White Y Set All False v o 1 Top v Invert aiki HHHH Write Verify Read Design Design Design Interrogate Disable Set to Module Config Demo Mode Sleep Mode Note This requires a CAN USB adapter and 482CRM module 1 Connect the 482CRM module to the PC via CAN to USB adapter 2 Open CANconnect and click Request Broadcast The attached module should show up in the Modules section Double click the module to open up the editing interface 3 Go to Connect and interrogate Module In the information message field the address of the module the model and firmware version are listed 4 Under Message Transmitted By Module set the ID field as 18EFFF94 Set Bytes at 8 Period to 1000ms and Minimum to 100ms Note This Message ID is for illustrative purposes only and can be set to whatever works with your system 36 5 For the Byte Bit representation field use the Bit Selector drop down menu to select Switch with the value 1 and Top in the corresponding fi
9. A DATE CODE 12 05 2011 DESIGN DEMO SERIAL CE000111 File New Resets all values in the interface to defaults Close Closes the window Tools Open Diagnostics Window Factory use only Connect Interrogate Module Returns the device address and version information that is being edited Write Design This exports the newly created design to the device to use Verify Design This checks to make sure the design is correct on the device 29 Read Design This imports the design that is currently stored on the device Note Bad response message may occur upon request check connections and retry Read Design Read Diagnostics Factory use only ee O O File Tools Connect A Message ID 00000080 Transmission Period 1024 ms Bytes 8 v Transmit On Change Minimum Period 32768 ms B Byte Bit C Constant Input 1 1 y o 01 y V Active Low Byte 1 oo Input 2 5 v 3 08 v I Active Low Byte 2 04 Input 3 2 v 04 y Active Low Byte 3 90 Input 4 1 y o 01 Active Low Byte 4 zo Input 5 1 v 1 0 Active Low Byte 5 00 Input 6 10 v o 01 y Active Low Byte 6 o4 Input 7 1 yj 04 j 7 Active Low Byte 7 00 Input 8 1 y o 01 Active Low Byte 8 EJ Toggle All D A The Message ID field edits the specific address for the module When the Transmit on Change box is checked the
10. CANcreate simulator Note Make sure CAN Connect isn t open when testing with the CANcreate software 3 Use the virtual display to select the appropriate module and open up the module s page 4 From the simulator you can observe the receiving and transmitting of data between the software and the CAN module 42 Chapter 5 Error Messages 5 1 Error Message Table Error Message ERR_OK OK ERR_XMTFULL Send Buffer Full ERR_OVERRUN Overrun ERR_BUSLIGHT Bus Light ERR_BUSHEAVY Bus Heavy ERR_BUSOFF Bus Off ERR_QRCVEMPTY Receive Queue Empty ERR_QOVERRUN Receive Queue Overrun ERR_QXMTFULL Send Queue Full ERR_REGTEST Register Test Failed ERR_NOVXD No VxD Available ERR_HWINUSE Hardware in Use ERR_NETINUSE Net in Use ERR_ILLHW Invalid Hardware Handle Device Not Connected ERR_ILLNET Invalid Net Handle 43 ERR_ILLCLIENT Invalid Client Handle ERR_RESOURCE Unable to Generate Resource FIFO Client Timeout ERR_PARMTYP Parameter Not Permitted ERR_PARMVAL Invalid Parameter Value ERR_NO_DLL No DLL Present ERR_TIMEOUT Time out communicating with 514UTC ERR_DATAERROR Data error communicating with 514UTC ERR_TXERR Transmission Error Detected ERR_MLOA Message Lost Arbitration ERR_ABTF Message Aborted Flag 5 2 Err
11. High Byte a0 Byte 3 channel 2 Low Byte gt 00 Buttons Byte 4 channel 2 High Byte v 00 Sloane n io oe MA Ee T Byte 6 Channel 3 High Byte v oo Booi ay wea Button 2 D Test Counters Byte 7 Channel 4 Low Byte v 00 7 Button 2 Byte 8 Channel 4 High Byte v 00 Button 3 Button 3 A When connected to the module each Channel will display the corresponding number on the module The empty bar next to each channel will visually fill up when reaching its programmed maximum The actual number will be displayed next to it B The Channel Configuration section has Channel 1 displayed first by default This section allows the setting of the minimum maximum and decimal location for each channel Use the drop down menu next to Channel to select channels 1 to 4 The minimum allowed is 0 and the maximum allowed is 9999 Checking the enable box turns on and off a channel Checking the Rollover box will allow the user to return to the minimum when the maximum is reached without turning the dial back the same direction 19 C Within the Message Configuration section the Message drop down menu can select between 4 different messages Each message will have its own Message ID and specify its own selection of bytes to receive read Use the Enabled check box to turn on and off individual messages Check the Transmit on Change box to transmit a message every tim
12. The number field can be set from 1 to 8 Each represents a switch on the module from left to right starting with 1 Set the value as 2 insert a Red LED and the number will be shown as 2 meaning switch 2 The drop down menu with top and bottom is used to select the top or bottom LED on the switch Checking the Invert box will set the LED to be true on zero instead of a one Bit Types False This bit will always transmit as a zero Has no effect on received messages True This bit will always transmit as a one Has no effect on received messages Switch Represents the status of a switch Use the switch selector to select which of the eight switches and the row selector to select whether it s the up or down switch Has no effect on received messages LED Used to control the LED Use the switch selector to select which of the eight switches and the row selector to select whether 15 it s the top or bottom LED Transmitted messages with LED bits will reflect the status of the last received message Enable A single bit that enables the top or bottom row of LEDs This control is optional If no enable bit is specified the LEDs will default to on Use Enable All to enable both the top and bottom rows of LEDs with a single bit Power Up to eight bits for each row that represent the power intensity of the LEDs A value of 0 is 0 and a value of 255 is 100 Any power bits after the first eig
13. ad write verify messages will be shown in this message section 31 Chapter 4 Tutorials 4 1 521CRED Tutorial 521CRED Configurator v2 7 o n N nl File Connect Channel 1 Channel Configuration Channel Channel 1 M Channel 2 Channel 3 Minimum 0 Maximum 3999 Channel 4 Decimal a IV Rollover Message Configuration Message Message 1 ig V Enabled Transmission Period 1000 ms Message ID 18FEF44A V Transmit On Change Minimum Period 100 ms Byte 1 Channel 1 Low Byte ne 00 Bytes 8 v Byte 2 Channel 1 High Byte v Byte 3 Constant me Byte 4 Constant Buttons Test Counters Request Dial TIT Byte 5 Constant Button 1 Byte 6 constant X o0 J Button 1 Byte 7 Constant X 00 Button 2 Bai Conia Byte 8 Constant s 00 Button 3 Button 3 Note This requires a CAN USB adapter and 521CRED module 1 Connect the 521CRED module to the PC via a CAN to USB adapter 2 Open CANconnect and click Request Broadcast The attached module should show up in the Modules section Double click the module to open up the editing interface 32 Go to Connect and interrogate Module In the information message field the address of the module the model and firmware version are listed Under the Channel Configuration section use the drop down menu to select between each channel Use the check box to enable ea
14. ch channel and set each with a minimum to 0 and maximum to 9999 Rollover should also be active Under the Message Configuration let only Message 1 be enabled Set the transmission period to 1000ms and minimum period to 100ms Write the Message ID to 18FEF44A with Transmit on Change checked Note This Message ID is for illustrative purposes only and can be set to whatever works with your system Using the drop down menus set Byte 1 to Channel 1 Low Byte and Byte 2 to Channel 2 High Byte For bytes 3 to 8 set to Constant Go to Connect and Write Design The module is now programmed OPTIONAL Follow the Post Test Setup instructions to test the newly edited 521CRED Sf 4 2 524AM Tutorial 524M Configurator V7 ele So ba File Connect Volume Control o Volume oft MV Disable Manual Controls oft On Save Restore Configure Alarm Alarm 1 nd Message ID 18FEF44B Data Bytes 01 00 00 00 00 00 00 00 Transmit Message Mask 1FFFFFFF Data Mask 01 00 00 00 00 00 00 00 Pattern T a E 64 64 Count 3 Speed 1 Volume 50 Note This requires a CAN USB adapter and an 8 switch 524AM module 1 Connect the 524AM module to the PC via CAN to USB adapter 2 Open CANconnect and click Request Broadcast The attached module should show up in the Modules section Double click the module to open up the ed
15. e Note Bad response message may occur upon request check connections and retry Read Design Read Diagnostics Factory use only File Tools Connect Channel 1 A Channel Configuration o sov Channel 2 B Channel Channel 1 vj 4 20mA A Zero Offset o Channel 3 o sv Multiplier 1 000 Channel 4 o sv E Channel 5 o sv Direct Read Mode Message Configuration Cressase Message 1 v IV Enabled Transmission Period 1000 ms Message ID 00000000 Transmit On Change Minimum Period Bytes 8 v Byte 1 Channel 1 Low Byte D Byte 2 Channel 1 High Byte Byte 3 Channel 1 Adjusted Byte 4 Channel 2 Low Byte Byte 5 Channel 2 High Byte Byte 6 Channel 2 Adjusted Byte 7 Channel 3 Low Byte Lalla fa lel lalla Lal fa Byte 8 Channel 3 High Byte A When connected to the module each Channel will display the corresponding voltage value on the module The empty bar next to each channel will visually fill up in accordance to the value being read The actual number will be displayed next to it B Under the Channel Configuration there are 3 fields The Channel field contains a drop down menu to select what channel that you want to edit Channels 1 to 5 The Zero Offset and Multiplier field are used to calibrate the module for the system For channels 3 to 5 the Voltage Mode box can be ch
16. e the value changes unless it will only transmit at the set transmission period Set the transmission period in milliseconds in the Transmission Period field and set the minimum period in the Minimum Period field Use Bytes 1 to 8 and the drop down menu adjacent to specify the channel it associates with and whether it uses the high or low byte D The Buttons make sure the buttons are working correctly The Test Counters are for factory use only E The information message section indicates what actions have occurred and may be currently executing Any errors or successful read write verify messages will be shown in this message section 20 521CRED Physical Device The module has a digital display 3 buttons and the adjustment dial The 2 buttons with the up and down arrows increase decrease the channel being accessed The lock button can be set to lock the channel and dial defaults as free input Turn the dial clockwise to increase the numbers and counter clockwise to decrease them Tuning the dial faster will change the numbers at a quicker rate while turning it slower will provide a more accurate fine tuning adjustment Note Turning the dial too quickly may cause it to skip increments 21 3 3 524AM Interface Close Closes the window Connect Interrogate Module Returns the device address and version information that is being edited Write Design This exports the newly cr
17. eated design to the device to use Verify Design This checks to make sure the design is correct on the device Read Design This imports the design that is currently stored on the device Note Bad response message may occur upon request check connections and retry Read Design Read Diagnostics Factory use only Ze 5244M Configurator v2 8 oll File Connect Configure Alarm Message 1 v A Manual Control LED 1 Warning B Message ID 18FFFE10 Data Bytes 00 00 00 00 00 00 00 00 Transmit LED 2 Error Message Mask 1FFFFFFF Data Mask FF FF FF FF FF FF FF FF Jalarm X Switch Mute Volume Control o off On D Pattern sest Hirr see t ssr Eha a E Count l Speed 250 12 If Count 255 alarm must be manually silenced Enable Manual Control V Enable Status Message F Message ID 18FFFE10 faecal 1000 Pas LED 1 Warning LED 2 Error Switch Mute A The Configure Alarm box allows for the implementation of 4 individual alarms or actions on the same device that correspond to different messages on the CAN bus Use the drop down box to select between them Note The same message mask will be shared across all 4 alarms B The Message ID is a 29 bit CAN ID that is associated with each alarm Use the Message Mask to mask out what bytes are needed and not needed for the alarm to sound If the Data Bytes match the Data Mask the
18. ecked and activated Note When voltage mode is unchecked these channels will measure a resistive input 27 C Under Message Configuration the Message field drop down menu can be used to add edit up to 5 different messages Checking the Enabled box will activate that message number They each have their own Message ID which can be changed in the Message ID field Checking the Transmit On Change will have the module send data every time it gets modified instead of waiting for the set transmission period It will not transmit any faster than the value set in the Minimum Period field D There are 8 Byte fields each can be set to look at a certain channel s voltage and select either the low byte high byte adjusted byte or make it a status register The resolution of the value is actually 10 bits so a maximum value of 1024 in order to get the full representation it takes 16 bits to transfer the data but the real value is only 10 bits Use the adjusted byte to get a converted input value in 8 bit form instead of 16 bit The status register is used for error detection resulting from external fault due to a fuse trip E The information message section indicates what actions have occurred and may be currently executing Any errors or successful read write verify messages will be shown in this message section 28 541CEI Interface HMI SYSTEMS PN EL40073 MODULE 541CEI VER 1 0 REV
19. elds Click in bit O of Byte 1 A light blue box should show up with 1 inside and an white oval at the top Change the value under Bit Selector to 2 Click bit 1 of Byte 1 Repeat until all 8 bits are filled in Byte 1 The last should be switch 8 in bit 7 6 For Byte 2 repeat step 5 except change the Top property to Bottom Leave Bytes 3 to 8 blank 7 Under Message Received By Module set the ID field as 18EFFF93 and Mask as 1FFFFFFF Leave Bytes as 8 and Cycle Test unchecked Note This Message ID is for illustrative purposes only and can be set to whatever works with your system 8 Use the Bit Selector to pick Red LED set the value as 1 and drop down menu to Top Click the bit O in Byte 1 of the receiving message Increment the value to 2 and click bit 1 in Byte 1 Repeat up to value 8 for bit 7 9 Change the property to bottom and repeat step 8 for Byte 2 10 Change the Bit Selector to Green LED and repeat step 8 for Byte 3 Then change the property to bottom and fill in Byte 4 11 Change the Bit Select to Blue LED and repeat step 8 for Byte 5 Then change property to bottom and fill in Byte 6 12 Next use the Bit Selector to pick Enable All Click bit O in Byte 7 A yellow box with two white ovals should be placed 13 Return to the Bit Selector and change to Power Make sure the top property is active Click on bits O to 3 in Byte 8 Purple boxes should be placed with top ovals For bits 4 to 7 use Power wi
20. ht will be ignored If less than eight bits are specified the least significant bits are filled in with the value of the most significant bit The bits specified are assumed to be the most significant This control is optional If no power bits are specified the LEDs will default to 100 on Use Power All to set the power of both the top and bottom rows of LEDs with the same value F The Colors drop down menu has a selection of colors from black to white The top 8 boxes represent the top LEDs on 8 switches The bottom 8 boxes represent the bottom LEDs on 8 switches Using the drop down menu colors can be put into the boxes Then use the Bit Selector LED option in the Message Received bytes to enable that color in the corresponding bit This method allows for LED control condensed to 2 bytes but limits the LED customization G Under Design Controls the design can be programmed onto the module through Write Design You can verify the design on the current module through Verify Design To import the current design from the module use Read Design To get the module s address and version information use Interrogate Module You can use Disable Config to disable configuration on the module There is also a Set to Demo Mode button to put the module into demo mode Note Bad response message may occur upon request check connections and retry Read Design H The information message section indicates what actions have occurred and may be
21. in the CAN system The Bytes field specifies how many bytes The Period field specifies how often the information is being sent in milliseconds The Minimum field is the fastest the data can be sent when transmitting on change The NAME button opens a new window that edits the message that will be transmitted when the module powers up 14 B This is the visual representation of the bytes being transmitted Each byte is broken down into each of its 8 bits Here the individual bits within each byte can be changed to be associated with a certain switch and or switch position that the receiving CAN module can decode C The Message Received By Module section is where the address and mask can be set to listen to the correct module The number of bytes to use is specified and if you want to the cycle the test when testing the LED configuration using the LED On and LED Off buttons D This is a visual representation of the bytes received and what the significance of each bit has for the LEDs on the module Using the tools below LEDs can be set to a variety of colors and locations top or bottom LED on switch E The Bit Selector includes False True Switch LED Enable Power Enable All Power All Red LED Green LED and Blue LED Each affects the switches in a certain way Some are associated with a certain color which will be seen in the square next to the drop down menu Enable for example is represented with yellow
22. iting interface 3 Go to Connect and interrogate Module In the information message field the address of the module the model and firmware version are listed 4 The Volume Control field is used to test the correct volume for the module Setting a number in the field and clicking the On button will play that sound from the module Leave Disable Manual Controls checked 34 Under Configure Alarm select Alarm 1 For Message ID write in 18FEF44B Next in the Data Bytes field and Data Mask field put 01 00 00 00 00 00 00 00 In the Message Mask field put 1FFFFFFF Note This Message ID is for illustrative purposes only and can be set to whatever works with your system To specify the pattern use 1 s and O s Type in 111100001111000011110000111100001111000011110000111100001111 0000 This will then change to TU eel sees TY pase T ao for a better visualization of the pattern Finally set Count to 3 to repeat the pattern 3 times set Speed to 1 and Volume to 50 Go to Connect and Write Design The module is now programmed OPTIONAL Follow the Post Test Setup instructions to test the newly edited 524AM 35 4 3 482CRM Tutorial a File Tools Options Shi Ri ived Mi Message Transmitted By Module 482CRM gt CAN a S ee rpg ta 18EFFF94 Bytes 8 H Period 1000 ms Minimum 100 ms NAME Tog Messages 1 2 3 4 5 6
23. l other applications before continuing with install License greement The licenses granted here are forever unless CUSTOMER violates these DEFINITIONS provisions in which case HMI has the right to terminate these licenses at any time License Agreement CANCREATE is a standard software suite owned exclusively by HMI 5 A Systems Inc HMI and intended for development management and end Alllicenses are granted to the single designated business entity only user interfacing to the HMI Systems product line This software suite ee aye includes the CANconnect design entry and programming tool and the By clicking on Accept you signify that you have read fully and accept the CANcreate GUI generator terms of this license agreement IV Create Desktop Icons Accept V Create Desktop Icons Install Path Install Path C Program Files CANcreate C Program Files CANcreate Messages Messages Decompressing archive Decompression completed Installed components CANconnect CANcreate Boot650 Creating desktop shortcuts Creating start menu shortcuts Cleaning up Installation completed successfully 1 2 USB Connection The CAN Connect software needs a CAN to USB adapter It supports both the 514UTC USB adapter and the PCAN Gridconnect USB CAN adapter 514UTC USB Adapter PCAN Gridconnect USB CAN Adapter Chapter 2 Interface 2 1
24. or Information Transmission error detected A connection isn t working or set up correctly DLL could not be loaded when opening CANconnect Typically means that you already have a copy of CANconnect open or the GridConnect drivers have not been loaded Fail to Read Write Bad response message may occur upon request check connections and retry Read Write Design 44
25. ot pressed Byte 2 Current active alarm value from 1 to 4 G The information message section indicates what actions have occurred and may be currently executing Any errors or successful read write verify messages will be shown in this message section AS OA AHEM AL OLED LAAN LAD STEM AAA O IRENE LA YEE DIE T T pe ERI WARN MUTE ERROR 524AM Physical Device Two indicators are provided for warnings and errors The default mode will illuminate the red error LED and green warning LED during an alarm annunciation Hitting the mute button will turn off the alarm annunciation tone The green warning LED will remain lit until after the alarm annunciation is finished even if the mute button is pressed The red error LED will remain lit until the mute button is pressed 25 S40SIM Interface OM ens PN EL40072 MODULE 540SIM VER 1 0 REV A DATE CODE 12 07 2011 DESIGN DEMO SERIAL 10001017 New Resets all values in the interface to defaults Close Closes the window Tools Open Diagnostics Window Factory use only Connect Interrogate Module Returns the device address and version information that is being edited Write Design This exports the newly created design to the device to use Verify Design This checks to make sure the design is correct on the device 26 Read Design This imports the design that is currently stored on the devic
26. rkspace Cont Hardware Address Control Select az Read Master Write Under the Hardware Address Control section Use select to pick module Can read or write displayed address of selected module Use master to communicate with any module regardless of address Note Should only be used when one module is attached to CAN network at a time The master address can be selected and force a module of unknown address to the displayed address by clicking the write button Modules s modure version can tp putter Modules Section Lists the connected modules Displays the following information Address Serial Number Module Type Version Number CAN ID Buffer Number 11 2 2 Main Transmission Workspace Cont Messages can ID Bytes Data Period Count Changes Messages Section Lists the incoming messages from the connected modules Displays the following information CAN ID Bytes Data Period Count Changes Information Message Section The information message section indicates what actions have occurred and may be currently executing Any errors or successful module commands will be shown in this message section 12 Chapter 3 The Modules 3 1 482CRM Interface File New Open new crm file Import Import previously created crm file Export Export current 482CRM configuration as crm file Close
27. st The attached module should show up in the Modules section Double click the module to open up the editing interface 3 Go to Connect and interrogate Module In the information message field the address of the module the model and firmware version are listed 40 Inthe Message ID field write 18EFFF97 Check the Transmit On Change box Set the Transmission Period to 1000ms and Minimum Period to 100ms Make sure Bytes is set to 8 Note This Message ID is for illustrative purposes only and can be set to whatever works with your system For every input 1 to 8 under the Byte column set each drop down menu to 1 Under the Bit column set Input 1 to 0 For Input 2 set bit to 1 Repeat for Inputs 3 to 8 with bits 2 to 7 Click Toggle All to make all Active Low boxes checked Under the Constant list of Bytes on the right set Byte 1 to 55 Leave Bytes 2 to 8 as 00 Go to Connect and Write Design The module is now programmed OPTIONAL Follow the Post Test Setup instructions to test the newly edited 541CEl 41 4 6 Post Test Setup OPTIONAL Once done with a tutorial 1 Open up CANcreate and load the TestLab ccs file Note If none of the images loaded open the Image Library and click Import Image Pack Locate the testlab cip file and click open Click Refresh in the Image Library and then Reload 2 Enable CAN Simulation and the
28. te Module New Module Select Read Open Interface Change Address Master Write Request Serial s Delete Module Modules Version Buffer Messages Initialization Error Invalid Hardware Handle Device Not Connected 0x1400 This is the main CAN Connect window Through it all USB connected modules can be monitored and edited through various separate interfaces within CAN connect The various components of this workspace are detailed in this chapter 2 2 Main Transmission Workspace Cont Request Broadcast Interrogate Module Open Interface Request Serial s Request Broadcast After hooking up your CAN system to the PC request broadcast will locate the attached modules The modules will show up in the Modules section and corresponding messages in the Message section Interrogate Module Returns the module address and version information that is selected Open Interface Opens the editing interface for the selected module Request Serial s Reads and lists the serial number for the selected module in the information message section Design Control New Module Change Address Delete Module Under the Design Control section New Module Create new Module with specific address and module type Change Address Change the Address of the selected Module Delete Module Deletes the selected Module 10 2 2 Main Transmission Wo
29. th bottom property active 14 Go to Connect and Write Design The module is now programmed 15 OPTIONAL Follow the Post Test Setup instructions to test the newly edited 482CRM 37 4 4 540SIM Tutorial File Tools Connect Channel 1 G SOV Channel 2 Channel Channel 1 idl 4 20mA Zero Offset o Channel 3 6 5 Multiplier 1 000 Channel Configuration Channel 4 0 5y M ve Channel 5 e bY Direct Read Mode Message Configuration Message Message 1 X V Enabled Transmission Period 1000 ms Message ID 18EFFF96 Transmit On Change Minimum Period 100 aa Byte 1 Channel 1 Low Byte v 90 Bytes 8 Byte 2 Channel 1 High Byte v 00 Byte 3 Channel 1 Adjusted v Byte 4 Status Register Me Byte 5 Constant Byte 6 Constant Byte 7 Constant Byte 8 Constant Note This requires a CAN USB adapter and 540SIM module 1 Connect the 540SIM module to the PC via CAN to USB adapter 2 Open CANconnect and click Request Broadcast The attached module should show up in the Modules section Double click the module to open up the editing interface 3 Go to Connect and interrogate Module In the information message field the address of the module the model and firmware version are listed 38 Under Channel Configuration verify that Channel 1 has a zero Offset of 0 and Multiplier of 1 Next under Message
30. ttern turn the buzzer on Continuous tones can be produced by multiple adjacent periods or lines To create your own pattern input zeros into the Pattern section to specify periods and ones to specify lines Once 64 characters are typed in the program will switch them to periods and lines for better readability E Below the pattern section is the Count Speed and Volume fields The Count field defines how many times the pattern will be played upon receiving the correct message and data combination Setting the count to 255 will repeat the alarm indefinitely and require either a message to clear or direct input from the operator through the mute button on the unit The Speed field will determine how fast the pattern is played upon receiving the correct message and data combination The lower the number the faster the message will be played higher numbers up to 255 add delay in between each of the Pattern s bits The Volume field will determine how loud each Pattern will be played The volume goes from 1 to 255 max Full volume is approximately 105cB 24 F Checking the Enable Status Message box will allow the ability to echo back a status message The status message will indicate the current state of the LED and switch Set the Message ID and the period then it will start broadcasting the information Status messaged defined Byte 1 Bit O Warning LED Bit 1 Error LED Bit 2 Switch status 1 pressed 0 n
31. vice Listing Change Address View Module Details Lists address buffer size and messages for debugging Device Listing Scan Scanning Number of Devices 1 Device 0 Flags 0x1 Open Type 0x0 ID 024036001 Locld 0x0 SerialNumber Description USB lt gt Serial ftHandle 0x8D1F 80 Device Listing Scans for number of USB devices connected Change Address Change the address of the selected HMI module This refers to the HMI address stored internally that is used to differentiate between multiple modules connected at once with different designs programmed Note This is not the physical source or destination address in the CAN network The address needs to be unique for each module 2 1 CAN Connect Toolbar Options Help Connect Using 514UTC Read Only Mode Receive Filter Connect Using 514UTC When checked uses 514UTC USB module when unchecked uses PCAN GridConnect USB module Read Only Mode Turns on off read only mode Receive Filter Filters message section to view only messages with a certain Message ID and Message Mask 2 1 CAN Connect Toolbar Help Title Displays CANconnect version number and copyright information About N A 2 2 Main Transmission workspace CANconnect v2 7 Untitled ccn _ ae File Tools Advanced Options Help Request Broadcast Design Control Hardware Address Control Interroga

CAN Connect User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents