Home

6 Inch Medium Speed Dome User Manual V2.0.0

1. 16 presets User can realize other function through the same meaning 6 Inch Medium Speed Dome User Manual Appendix 1 Lightning amp Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W like instantaneous lighting surging etc According to the actual situation outdoors necessary protection measures must be taken to secure the electrical safety 1 The distance between signal transmission line and High voltage equipment or high voltage cable is at least 50m 2 Outdoor wiring should better be along the eaves as much as possible 3 In the open field wiring should be buried underground in sealed steel pipe and the steel pipe should be one point grounding Overhead routing method is forbidden 4 In strong thunderstorm area or high induction voltage areas such as high voltage transformer substation high power lightning protection apparatus and lightning conductor are necessary to be appended 5 The design for installation and wiring with lightning protection and grounding in mind should be combined with the lightning protection consideration of the building and conform to the related national standards and industry standards 6 The system should be equipotentially grounded and the grounding equipment must satisfy double request of system anti jamming and electric safety and it must not appear short circuit and open circuit with the zero conductor of str
2. User Manual RS485 Distributor Figure 5 1 FAQ of RS485 Bus Fault Phenomenon Probable Cause The speed 1 The address or Baud Rate is not matched dome do the between Host and the Speed Dome self check but 2 R5485 are connected incorrectly can not be 3 Wiring drops controlled 4 R5485 wire broke The speed 1 loose contact of K5485 dome can be 2 one R5485 wire broke controlled but 3 Host and speed dome are too far awaye not smoothly 4 Too many speed domes are connected solutionse 1 Adjust the address or Baud Rate of Host or Speed Dome to make a match 2 Change the R5485 and R5485 wires 3 fastening the wirer 4 Change R5485 wire 1 fastening R5485 wire 2 Change R5485 wires 3 Add terminal matched resistances 4 Add R5485 distributore 6 Inch Medium Speed Dome User Manual Appendix 3 24VAC Wire Gauge amp Transmission Distance The following table has described the recommended max distance adopted for the certain wire gauge when the 24VAC voltage loss rate is less than 10 For the AC driven device the maximum voltage loss rate allowable is 10 For example for a device with the rating power of 80VA which is installed at a distance of 35 feet 10m away from the transformer then the minimum wire gauge required is 0 8000mm Distance __ feet m Power vay 0 8000 1 000 250 Pres 000 e 451 137 716 218 Ca an oo am on a an 6 Inch Medium S
3. of control device or client software The control devices include control keyboard and DVR etc And the client refers to the client application software Examples are given here for common operation provided that the current control system supports following operation Please refer to Client Software User Manual for detail operation guide Pan and tilt movement Move the joystick to the desired direction or press the Up Down Left Right buttons Zoom operation Press ZOOM TELE button to make the lens closer and magnify the scene Press ZOOM WIDE button to make the lens farther and minify the scene Focus operation After FOCUS FAR button is pressed the object far away will become clearer while the object in vicinity will be ambiguous After FOCUS NEAR button is pressed the object in vicinity will become clearer while the object far away will become ambiguous In auto focus mode camera will focus automatically to maintain clear image This feature can also be achieved by manually as well However after other operation of device camera will resume auto focus Iris operation press IRIS OPEN to enlarge the iris and increase the image brightness And by pressing IRIS CLOSE the iris will gradually shrink that decreases image brightness In auto iris mode the IRIS OPEN and IRIS CLOSE buttons are still operable However after finishing other operation by dome camera will resume auto iris action Preset operation Preset can be progra
4. 6 Inch Medium Speed Dome User Manual V2 0 0 2010 01 6 Inch Medium Speed Dome User Manual Thank you for purchasing our product If there is any question or request please do not hesitate to contact dealer This manual is applicable to 6 Inch Medium Speed Dome This manual may contain several technically incorrect places or printing errors and the content is subject to change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual 6 Inch Medium Speed Dome User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure 1s divided into Warnings and Cautions Warnings Neglecting any of the warnings may cause serious injury or death Cautions Neglecting any of the cautions may cause injury or equipment damage Warnings Follow these safeguards to prevent serious Cautions Follow these precautions to injury or death prevent potential injury or material damage Warnings 1 In the use of the product you must be strict compliance with the electrical safety regulations of the nation and region 2 Please use the power adapter which is provided by normal company The standard of the power adapter is AC24V 3A 3 Do not connect several devices to one power adapter as adapter overload may cause over h
5. age stability The medium speed dome can be widely applied to various monitoring scenes such as the river forest road railway airport harbor oil field sentry plaza park scenic spot street station stadium etc 1 2 Outline Back Box ia ksb FT Fea Dome Drive Bubble 6 Inch Medium Speed Dome 1 3 Functions o Self adaptive to Multiple Protocols The dome is compatible with PELCO D PELCO P and HIK Code protocol etc and is capable of being self adaptive to these protocols without need of selecting protocol by DIP switch settings Oo Keyboard Control The pan tilt movement and zoom actions of dome can be controlled by the control keyboard DVR matrix etc eo Limit Stops The dome can be programmed to move within the limit stops left right up down which are configurable by the control keyboard DVR or client application software Oo Presets Each of the user definable presets can be programmed to use pan tilt camera settings and other settings When preset is called the dome will automatically move to the defined position User is allowed to add modify delete and call each preset eo 3D Intelligent Positioning The speed dome can be controlled with the 2 buttons and scroll of mouse can be used under HIK Code protocols with devices and 6 Inch Medium Speed Dome User Manual client software Click on a certain area and the device will move to the scene with corresponding point as the center When a rectangu
6. e dome cover avoid direct contact with the dome cover because the acidic sweat of the fingers may erode the surface coating of the dome cover 7 Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover not to use alkaline detergents 6 Inch Medium Speed Dome User Manual Table of Contents TADO EE OPM CIS nennen AA EA lies AAA 3 Chapter LBS A db 4 1 BI T E WAREIRENERRRARRUREEERNENRARRNEORERENTAREUNSORIENTARTERSORTIENLARRENNERTIENKLARNERNERTIENSLARNERNERLIENHEALNERSERLRENSEALTER 4 A ieee a ee a eee 4 13 o naeh 4 Chapter 2 oa II oO nee ee en en en en nah 6 AN A o o eaeuas aeeuaen cents aeesae 6 ZO A nee 6 2 3 Presets Wilh Special Functions 0 ate I Appendix l Liehtnimne amp Surse POCO bobina 10 Appendix 2 RS485 Bus OMS C 110 1 nirereseta ne e a a a e ee 11 Appendix 3 24VAC Wire Gauge amp Transmission Distance ooooononoooooooooooooooonnnnnnnnnnnnnnnnnnonnnnnononnnnn nono nn nro nono non nnnnnnnnos 14 Appe dix4 Table of Wire Gange Standards iii 15 6 Inch Medium Speed Dome User Manual Chapter 1 Brief Introduction 1 1 Description Adopting the high performance integral dome drive with auto iris auto white balance and other capabilities the medium speed dome is integrated with the built in pan tilt unit and the digital receiver The dome provides Manchester code and wiring failure diagnosis with precise drive it features high reaction sensitivity and reliable running ensuring superior im
7. eat or fire hazard 4 Please make sure that the plug is firmly connected on the power socket 5 When the product is installed on wall or ceiling the device shall be firmly fixed 6 If smoke odors or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center 7 If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Warnings 1 Do not drop the dome or subject it to physical shock and do not expose it to high electromagnetism radiation Avoid the equipment installation on vibrations surface or places subject to shock ignorance can cause equipment damage 2 Do not place the dome in extremely hot cold the operating temperature shall be 30 C 65 C dusty or damp locations or fire or electrical shock will occur otherwise 3 The dome cover for indoor use shall be kept from rain and moisture 4 Exposing the equipment to direct sun light low ventilation or heat source such as heater or radiator is forbidden ignorance can cause fire danger 5 Do not aim the camera at the sun or extra bright places A blooming or smear may occur otherwise which is not a malfunction however and affecting the endurance of CCD at the same time 6 Please use the provided glove when open up th
8. ets to preset 16 patrol 2 is preset 17 to preset 32 patrol 3 is preset 33 to preset 48 o Pattern A pattern is a memorized repeating series of pan tilt zoom and preset functions that can be recalled with a command from a controller or automatically by a configured function park time task or power up By default the focus and iris are in auto status during the preset is being memorized o Power off Memory This feature allows the dome to resume its previous position or status after power is restored By default setting the dome supports the power off memory capability with the dwell time of 3 minutes 6 Inch Medium Speed Dome User Manual Chapter 2 Operation Instructions 2 1 Power up Action After the power is applied the speed dome will perform self test action that begins with lens actions and then pan and tilt movement After completion of power up self test actions the interface as shown in Figure 2 1 will be displayed on screen for 120 seconds The System Information displayed on the screen includes the Dome Address Protocol Version and other information The COMMUNICATION refers to the baud rate parity data bit and stop bit of the dome e g 2400 N 8 1 indicates the dome is configured with the baud rate of 2400 no parity 8 data bits and 1 stop bit Please refer to Section 3 3 1 for detailed information 000 2400 N 8 1 Figure 2 1 2 2 Basic Operations The following operation shall be done with the use
9. h 3 Close camera configuration Close parity and Verification C al res ifomaos COMINO AN AS oma o G TAO fe EN man O G Ee eee Start auto scan path low speed A IS EEE Ee ME A No paro 100 Set scan end position 2 Using Manchester code protocols turn the 4 5 6 of SW2 on the preset and corresponding function are as below rocoso 6 Inch Medium Speed Dome User Manual No 1 Pattern customized Close zoom display Night mode 54 se as os Clove wende consoli Close camera power se Clove cercanas Cose parity and Veco al feat fo EE Explanation Take using Pelco P D HIKVISION protocols for example integrated analog speed dome supports 3 patrols each of which support 16 presets patrol 1 supports preset 1 to present 16 patrol 2 supports preset 17 to present 32 patrol 3 supports preset 33 to present 48 the stay time and speed can be set The dome also support 2 auto scan path with movement limitation the speed is adjustable If don t set the movement limitation it moves continuously It support park action as well and park action time is optional from 10s to 300s There are 6 modes can be chosen from preset 1 to preset 3 auto scan 1 and patrol land pattern 1 Detailed operation is described as below Call 56 preset to call patrol 1 Select the video in the DVR press PTZ and Rec and input 056 to start patrol 1 and the dome will continuously scan among pre set
10. lar area 1s selected by left clicking the mouse device will move to its center and enlarge 1t With right clicking the lens will zoom in and the scroll can easily make the lens zooming and mouse operation automatically incorporates zooming effect Oo Auto Focus The auto focus enables the camera to focus automatically to maintain clear video images O IR Cut Filter The IR cut filter can be set to Auto Day and Night In auto mode the camera is capable of automatically switching Black amp White mode Night and Color mode Day with regard to environment lightening conditions In manual switch mode user can increase sensitivity in low light conditions by switching to Black amp White mode while the Color mode is preferred in normal lighting conditions eo Low Light Electronic Shutter The shutter speed will automatically slow down in low illumination conditions to maintain clear video images by extending the exposure time The feature can be enabled disabled by the menu o White Balance WB This feature automatically processes the viewed image to retain color balance over a color temperature range The default setting for auto white balance is ON o Patrol The speed dome provides up to 3 patrols In each patrol user is allowed to specify the scanning track by a group of user defined presets with the scanning speed between two presets and the dwell time at the preset separately programmable Each patrol support 16 presets Patrol 1 is pres
11. mmed or called through keyboard or menu The dome provides 256 presets Press the SHOT button and then the 6 Inch Medium Speed Dome User Manual numeric keys to call the programmed preset E g the callup of preset 08 can be achieved by pressing PRESET button and then the numeral 08 Please refer to Section 3 3 4 for the configuration of presets Note The callup of presets including the presets with special functions will be restricted by the limit stops 1f defined Callup of presets programmed out of the limit stops will be invalid 2 3 Presets with Special Functions The following presets are predefined with special functions l Using HIKVISION PELCO D PELCO P protocols the preset and corresponding function are as below raros seed Seran scan end positon O so o EOS ISSN DO CAES CTS camera aos Open ameno etre O spaces sect parolo stop fr 30 seconds sado Sehe parao stp fr 6O seconds sy Sa Ses Und SONY cane Cie Ses Uno SONY camer aan kamen parc o pateo O se ankam ao pat O sa ao ataco O me o arca sun O rs migas ECON E T EV TE O tos camita O orton Close oom day CE RO mae PO e C TAO Damon Ba nds O re ementretcanonizo Owr O ace Wahn Ano Whit ns O tis O maras ECOS onen mponionat uni oma mooo oo ones YT Bee nm Cie 52 53 54 55 57 58 59 61 62 63 64 65 67 70 71 72 73 74 75 76 77 78 79 1 6 Inch Medium Speed Dome User Manual 83 Auto scan pat
12. ong grid When the system is grounding individual the resistance should be no more than 4Q the section al area of the grounding cable should be no less than 25mm For grounding instructions please refer to the Installation Manual of Speed Dome video arrester 2 E lightning rod communicate arrester porer arrester The speed dome should be in the range of 45 degrees under the lightning rod the resistance of earthing conductor should be smaller than 41 i steel jacket 6 Inch Medium Speed Dome User Manual Appendix 2 RS485 Bus Connection 1 General Property of RS485 Bus According to RS485 industry bus standard RS485 is a half duplex communication bus which has 120Q characteristic impendence the maximum load ability is 32 payloads including controller device and controlled device 2 RS485 Bus Transmission Distance When using 0 56mm 24AWG twisted pair line according to different baud rate the max transmission distance theory table is shown as below 2400BPS 4800BPS 1200m The transmission distance will be decreased if we use the thinner cable or use this product under the strong electromagnetic interference situation or there are lots of devices are added to the bus on the contrary the transmission distance will be increased 3 Connection Method and Terminal Resistance 1 RS485 industry bus standard require daisy chain connection method between any devices b
13. oth sides have to connect a 120Q terminal resistance show as Diagram 1 the simplified connection method is shown as diagram 2 but the distance of D should not be too long 1 2 3 AH 32H Diagram 2 2 Connection of 120Q terminal resistor The 120Q terminal resistor can be connected through the DIP switch on the communications board as shown in Figure3 For a new dome the 120Q matching resistor is defaulted as unconnected switch on the eighth bit of SW2 it will be connected Conversely switch off the eighth bit of SW2 it will be unconnected 6 Inch Medium Speed Dome User Manual arial Figure 3 4 Problems in the Practical Application Normally users adopt star shape connection method in construction under this situation the terminal resistors must be connected between two farthest devices as Figure 4 1 and 15 but this connection method is not satisfy the requirement of the RS485 industry standard so that it will lead to some problems such as signal reflection anti Jamming ability decline when the devices are faraway At this time the dome will be uncontrollable or self running etc Figure 4 For such case the best way 1s adding a RS485 distributor This product can effectively change the star shape connection to which satisfies the requirement of RS485 industry standard in order to avoid those problems and improve the communication reliability Show as figure 5 6 Inch Medium Speed Dome
14. peed Dome User Manual Appendix 4 Table of Wire Gauge Standards Bare g gt e American Wire Gaae Cross sectional Area g British Standard Wire Gauge ofBaro Wire a Qu a gt Mo BO ho M Oo 05 Go 05 E B BR gt m on MP Go 100 M co M uj O 19 SWG

6 Inch Medium Speed Dome User Manual V2.0.0

Contents

Download Pdf Manuals

Related Search

Related Contents