Animation Laser Light Effect Green 60mW DPSS (532nm)
Contents
1. PULSE Animation Laser Light Effect Green 60mW DPSS 532nm Model Delta www pulse light co uk The lightning bolt within a triangle is intended to alert the user to the presence of un insulated dangerous voltage levels within the product s enclosure This voltage may be of sufficient magnitude to constitute an electric shock risk Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN To reduce the risk of electric shock do not remove cover of this device There are no user serviceable parts inside Refer servicing only to qualified service personnel The exclamation point within a triangle is intended to alert the user to important operating and maintenance servicing instructions in the literature accompanying the appliance Safety Precautions Read and retain these instructions Follow all instructions and heed warnings Laser light effects can if used incorrectly be very dangerous This product should be used in accordance with the HSE guidance publication HS G 95 The radiation safety of lasers used for display purposes this is available online in PDF format from http www hse gov uk pubns priced hsg95 pdf or from book stores under ISBN 978 O 7176 0691 7 Users of this equipment must be competent and fully aware of all safety implications of using laser products This laser effect falls into the classification 3B Full details of usage exposure MPE and safe2. 2 of HSG95 Congratulations on your purchase of this Pulse Delta Laser Effect 60mW output from this DPSS laser will add a different dimension to any light show Ideal for smaller venue s The bright green laser diode generates a stunning effect complete with animations in classic green Features amp Specifications Animation style effect Bright 60mW 532nM green laser diode Fan cooled DMX Sound activated Master Slave or auto modes ILDA control option 11 DMX Channels Mains voltage 230Vac 50Hz Fuse rating 2A 250V Power consumption 40W Dimensions WxHxD 250x190x100mm Weight 3 6kg Connections amp Controls A COOLING FAN DO NOT BLOCK JERE SAFETY HOOK _ O O a O oo Jo Q D O O Powe Q G DMX 3 DMX e O 240Vac 50Hz Fuge Rating 2A QE ks www pulse light co uk 1 AC Power Input This must only be powered from a standard 240VAC 50 60Hz mains source Do not use with dimmer packs or electricity supplies outside this range A fused power cord must be used 2 Min Max Adjusts sensitivity to sounds within the bass range of the audio spectrum The sensitivity allows the control over the unit 3 Safety Hook Rigging of this device must only be carried out by competent persons and in accordance with the latest recommendations The Safety Hook point is to allow the use of a correctly rated secondary fixing the main suspension must be from the main yoke located on the top of the
3. the back of the master unit to make the unit more or less sensitive in sound active The panel has LED indicating for sound active a ai fa a 1 Master Sound AUTO 7 Slave W laye DMX Operation This mode allows you to use universal DMX 512 console to operate the laser 1 Use standard XLR DMX cable chain your units together via the XLR connector on the rear of the units We recommend a terminator at the last fixture ask your local dealer to supply a PULSE DMXTERM 3P 2 Assign a DMX address to each the unit using dipswitches T z TE a a a a ji ieee ji i ecw ji lone DMX Signa 1 JM 2 DMA MODE No DMX 3 Power up the unit the laser will then go through a reset cycle and begin operation in DMX mode 4 Use DMX console to control your units Operation e We recommend this product is used within a 4 hour duty cycle To do this the unit should be operated for no more than 4 hours without then being left to cool to room temperature and held at this temperature for 15 minutes This will prolong the life of the laser diode e In accordance with HSG95 this product is fitted with a key switch amp active LED the key switch is to allow operation of the device by persons who are responsible and are competent to do so e Do not operate in dusty or damp conditions The cooling fan must be kept clean and free of obstruction to prevent overheating e Control of this unit is via the Sensitivity control knob thi
4. unit 4 Power Switch On Off mains override 5 Earth Point As a Class I device this must be earthed the earth point can be used when checking the earth continuity during periodic Safety inspections At no point should the earth be removed from this device 6 Cooling Fan This device uses a fan to maintain its operating temperature this must be kept free of obstructions and cleaned as part of a periodic inspection routine Cleaning can be done with a non conductive brush and low power vacuum cleaner while the unit is switched off and isolated from the mains supply 7 Key Switch The key switch should only be operated by persons competent with laser operation When not in use keys should be stored in a secure position away from the laser device 8 ILDA Input The laser can be controlled using the international standard ILDA software 9 Function Dip Switches Select from either Sound Active Auto or DMX modes To set the unit to DMX mode simply set the DMX address using DIP switches 1 thru 9 For SOUND ACTIVE Auto or Slave modes set DIP 10 to on you can then add further control by using the first two DIP switches 15t ane Pattern OFF OFF Sound master ON OFF AUTO OFF ON Slave ON ON AUTO Animation 10 DMX Input Ouput In DMX mode the unit will respond to standard DMX512 signals The laser requires 11 channels for operation detailed in the table below Channel Function Value Description Master Mo
5. s will adjust how the unit reacts to bass notes and beats within the audio spectrum e Care should be taken to ensure this product is operated in accordance within the HSG95 guidelines e To generate the maximum effect lasers are best used in conjunction with haze machines e The front panel of this unit has a blue LED to indicate when it is active and detecting sound if the sound ceases to be detected the unit will enter standby after 8 seconds Trouble Shooting Fault Description No laser output Suggested Solution Check the power supply indicator on the front panel if this is not lit firstly check the unit is powered up and connected to a live mains outlet Check the mains On Off switch and the safety Key Switch override The lasers are protected by a fuse in the 13A IEC cord and also one on the mains input IEC connector Both fuses should be replaced by the Same type and value The lasers are sound activated if the sound level is too low or the unit is on minimum sensitivity the unit may enter standby mode Either increase the sensitivity or turn up the sound level Care should always be taken when using PA systems etc as high SPL s can present a danger to your hearing Assuming all of the above have been checked and the unit is still unresponsive please return the unit to the retailer from whom you originally purchased the unit e If the unit is not responding e If the Power Supply indicator light is illumina
6. t unauthorised use Ensure that ventilation holes and fans are always kept clear of dust and blockages this can be done when the unit is powered off using a clean fine paint brush and a low power vacuum cleaner Maximum loadings on stands rigging and truss must be observed at all times This item should also have a secondary fixing attached in the way of a safety bond wire All rigging should be carried out by competent persons Users need to be competent to operate display laser installations They should a Appoint a laser safety officer and provide effective supervision unless the installation is permanent designed to operate entirely automatically and does not scan audiences and b Ensure that all operators are trained to operate and maintain their installation safely and that they receive general instruction on laser hazards arising from visibly emitting lasers and the safety precautions that need to be taken Users need to have effective systems of work for maintenance alignment checks and setting up procedures If safety assessment of these activities indicates that there is a risk of hazardous personal exposure employees must be provided with appropriate protective eyewear Users should determine the extent of any laser hazard areas that arise during a display event so that personal access can be controlled The user should ensure that the minimum separation distances given in this guidance are observed see Supervision in Chapter
7. ted indicating the mains supply is present and the unit does not respond check the 10 Compliance When this product reaches the end of its life do not dispose with household waste See www recycle more co uk for details of how to dispose of PULSE products in an environmentally sound fashion or contact PULSE directly via www pulse light co uk E yh C Warranty Pulse products are warranted by Pulse against manufacturer defects for a period of one year from the original date of purchase This warranty is limited to manufacturer defects in either materials or workmanship PULSE or any other worldwide divisions of Premier Farnell PLC is not responsible for any consequential or inconsequential damage to any other component structure or the cost of installation or removal of said items Defective items should be returned to the retailer from whom they were originally purchased This warranty will not cover damage due to improper use This equipment contains no user serviceable parts Repair by any persons other that those appointed as PULSE service agents may void the warranty For questions or specific information regarding warranty replacement or repair contact PULSE www pulse light co uk 11
8. tor Rotation P mage Flip TE Horizontal amp Vertical Movement l CH8 Horizontal Size 64 255 Stretch CH10 Zoom Hu Imagesize 0 255 S Stand Alone Operation Sound Active amp AUTO Modes The mode allows a single unit to react to the beat of the music in the master mode 1 Set dipswitch to select Sound Active or AUTO mode 2 Power up the unit the laser will then go through a reset cycle and begin operation 3 The unit will react to the low frequencies of music via the internal microphone Adjust the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in sound active The front panel has LED indicating for sound active Master Slave Mode This mode will allow you to link up to 32 units together without controller 1 Install the units in a suitable position laying or appending 2 Choose a unit to function as Master mode set dipswitch to select Sound Active or AUTO mode The others must be set to Slave mode set dipswitch to select Slave mode 3 Use standard XLR microphone cable chain your units together via the XLR connector on the rear of the units For longer cable runs we suggest a terminator at the last fixture 4 Turn on the all units power the units begins reset then the unit begins working The slave units will react the same as the master unit 5 The units will react to the low frequencies of music via the internal microphone Adjust the audio sensitivity knob on
9. ty precautions can be found in the HS G 95 publication Extreme care should be taken to avoid all eye contact direct or indirect with the beams emitted from this unit Install in accordance with the manufacturer s instructions and only use indoors The laser must be mounted so that its emission is always directed away from people and animals taking great care to avoid any objects that may reflect the beams towards people HS G 95 states that separation distanced of 3m vertically and 2 5m horizontally must be observed This was correct at time of print Laser Projector fal EIR gt S r Det An ri A i o P y Se A og Py t Y A res Vey bey PA Accessible emission below he OY Re Rae Sew 7 i xt z Ap Bh Egh 23 the Applicable MPE RRS RCS SO POA DTTC e iaa tye PONELA ERAEN NASOS 7 ere a3 rAd Ne EIES Ay al re Oy O A me oe r gt i H i a Fh es ae b AY s r l l ns 3 e i A PAES TSE TOREPE J r ete C6 A gt a x r a ke A k gt To rel ey ed g af r Tir R AA rik sey eg B IMS arg N Oe Ae e S RA tp IRs pen dd oe N gia a 1 s Os 14 P ad e g 4 D 5 J d ay ng A 10 SRAN ORALE tte gt h Pe Se Pn ein 4 SY Ose A P ae TNR PE NETA fe pies Lene 5 EHA ki tha at L a Ket vp VASAS Stns 4s al Emission may exceed the applicable MPE at a height exceeding 3 metres Laser projector Audience excl
10. usion zone Lateral separation distances Do not block ventilation openings Do not install near heat sources such as radiators heat registers stoves or other devices that produce heat Do not defeat the safety purpose of the grounded plug This plug has two blades and a third ground prong The wide blade or third prong are provided for your Safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being stressed at the plugs convenience receptacles and where they exit the amplifier Unplug the device during lightning storms or when unused for an extended time Refer all servicing to qualified personnel If the surface becomes dirty clean only with dry cloth do not use solvents or thinners This device must not be exposed to water in any way No object filled with liquids Should be placed on apparatus When due for replacement fuses should always be replaced by the same type and rating Using fuses of incorrect type and or rating may present a dangerous situation Never remove any safety warnings or markings applied to the product This product is designed to be connected directly to a standard mains outlet 240Vac 50Hz Do not connect via any form of dimmer Laser effects are fitted with key switches as safety overrides these must not be defeated neither should the keys be stored in the unit when not in use The key switches are designed to preven
Download Pdf Manuals
Related Search