Home
Untitled
Contents
1. You may need to reposition the Clamp repeatedly until you identify the best spot The microphone must be positioned vertically and not Horizontally and let the side with MIC text to face mouth W Glue plate method You have the option to glue the Helmet Clamp onto your helmet when the above standard method cannot be used or in case you prefer to secure the Helmet Clamp with adhesive glue This option has been successfully used for a range of high end helmets NOTE While we have no reason to believe that the gluing option might negatively affect any helmet we do not assume any responsibility to that affect irrespective of its nature and circumstances The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims Caution This process can be done only once Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp s back plate 2 Determine the location on the helmet where the Helmet Clamp must be attached Adjust the Helmet Clamp s location on the Helmet so that the microphone is located opposite the center of your mouth You may need to reposition the Clamp repeatedly until you identify the best spot The microphone must be positioned vertically and not horizontally Be sure to clean the selected area prior to the gluing process 4 Peel the foil cover from the Glue Plates adhesive pad 5
2. function is activated a With the V1 V2 headset turned off press and hold the CTRL Bluetooth for at least six seconds until the Red and Blue Light begin rapidly alternating 3 Search for Bluetooth devices on your phone by following the phone s instructions Please consult your phone s User Manual for more information 4 After a few seconds the phone will list the V4 V2 as a discov ered device Select it and follow your phone s instructions to accept the pairing 5 When prompted enter 0000 four zeros as your PIN or passkey 6 Your phone will confirm that pairing has succeeded and the headset will begin flashing slowly in Blue With some mobile phone you may need to tap the CTRL button to con nect the headset to the phone after pairing is complete The V1 V2 headset will automatically connect to the last phone connected to the headset STEP 3 SET UP FOR BLUETOOTH GPS DEVICE PAIRING Ifyou have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset s speakers you must first pair your headset to the GPS device NOTE Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the V1 V2 Please consult your GPS device s User Manual for more information TO PAIR THE V1 V2 TO A BLUETOOTH GPS DEVICE 1 Turn on your GPS device 2 With the V1 V2 headset turned off press and hold the CTRL Button for at least six second
3. MC Button for 1 5S to stop playback 4 Short press VOL or VOL button to skip forward or skip backward AD None Headsetis off Alternating Red Blue flashes Pairing mode Blue short flash every 3 seconds connecting unavailable Blue long flash every 3 seconds connecting available Red flash every 3 seconds Battery is low Solidred Headset is being charged Your headset is eguipped with a high guality FM Radio receiver The V1 V2 enables you to listen to FM Radio while you are not receiving audio from another audio source While listening to the radio you do not have to worry about missing any calls as the headset automatically mutes the FM Radio and switches to Bluetooth headset operation when an incoming call is received or when you decide to initiate a call When the conversation is over the headset automatically tunes back to the FM Radio Turning the FM Radio On While no call is on the headset either mobile phone call or Intercom call double press MC Button on your headset to turn on the radio The radio tunes in to the last radio station you were listening to With some phones you should wait a few seconds after ending a call before turning on the Radio 13 Turning the FM Radio Off While the radio is turned on double press MC button to turn the Radio off Searching for a new FM Radio Station While the Radio is on short press Volume Up or Volume Down Button to search the nex
4. Motorcycle Helmet Headsets User Manual Ver 3 1 ee J CE Thank you for having chosen the V1 or V2 Bluetooth headset for bikers This Manual will help you operate the headset but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and or GPS device before using the headset The retail box of the V1 or V2 contains one headset unit When paired with another V1 or V2 the headsets can be used as an intercom at a rang of up to 100m V1 or 500m V2 The V1 or V2 offers the following uses 1 Bluetooth headset for mobile phone communication supporting headset and Handsfree profiles 10m range 2 Bike to Bike Intercom Communication with another V1 or V2 unit up to 100m or 500m range in Full Duplex mode purchased separately 3 Turn by Turn GPS Navigation instructions and Streaming Audio from compatible Bluetooth devices 4 FM Radio built in FM radio receiver 5 Bluetooth stereo enjoy stereo music from your A2DP enabled device like cell phone 6 MP3 jack As the speakers of your MP3 GPS just connect to your MP3 or GPS with audio cable The V1 or V2 can establish an audio connection with one Bluetooth device at a time Please read the section Using the Headset to see how you can switch the audio connection between the paired devices Mobile phones that do not support the Bluetooth handsfree profile may prevent you from using the Redial and Call Reject features Full
5. Place the Glue Plate into position according to 3 Press firmly 15 seconds on all 3 parts of the Glue Plate 6 The adhesive pad bonds to full strength over the next 24 hours Therefore it is recommended to not use the headset during this 24 hour period N Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed ATTACHING Slide the headset downwards along the sliding panel until a clicking sound Indicates that the headset is locked in place REMOVING Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand We recommend that you remove the headset from the helmet when not in use The microphone must be positioned vertically not horizontally in front of the center of the mouth p 5 Attach the speakers to the velcro inside your helmet opposite your ears short speaker cord for left ear A and the long speaker cord B for the right ear You may want to use the supplied Velcro pads Using two speakers inside the helmet may be prohibited in certain jurisdictions If this is the case You should tuck away the long corded speaker underneath the helmet padding as follows Lead the speaker B alongside the rim of the padding to the right side and then back to the left side near speaker A Then place the speaker B underneath the padding move GENERAL USAGE GENE
6. RAL FUNCTIONS DESIRED RESULT REQUIRED ACTION Turn on the headset Press CTRL Button steadily for at least three seconds Turn off the headset Press CTRL Button steadily for at least six seconds Long press the Volume Up Button Increase the volume Decrease the volume Long press the Volume Down Button Volume will automatically increase according to the wind noise AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the V1 V2 are prioritized as follows Highest 1 Mobile phone Audio Incoming outgoing calls 2 Buddy Audio 3 GPS device Lowest 4 FMRadio A high priority Audio Source will always interrupt any lower priority Audio Source 10 USING THE INTERCOM Making Intercom Calls To start a Buddy Intercom call with the last Buddy while the headset is on Standby you can Single tap the CTRL Button A Buddy Intercom call will be established To end the Buddy Intercom call single tap the CTRL Button again To start a Buddy Intercom call with the another Buddy while the headset is on Standby Press CTRL button steadily for 2 seconds A Buddy Intercom call will be established To end the Buddy Intercom call single tap the CTRL Button again CTRL Button Reconnecting the Intercom Ifthe V1 V2 and its Intercom Buddy headset go out of range and disconnect from each other You can manually reconnect at any time by short tapping the C
7. TRL Button Receiving Intercom calls If you are not speaking with any one once the other party tries to initiate a Buddy Intercom call the call will begin immediately stie PHONE FUNCTIONS Answer a call Short press the MC Button Long press the MC Button for 2 seconds Short press the MC Button Press and hold the MC Button for two seconds Reject a call Terminate a call Voice dial Double press Vol Button This function used only the user mobile phone supports the voice dial function NOTE If your Bluetooth mobile phone is paired to a Bluetooth GPS device not directly to the V1 V2 some of the above phone functions may not be compatible When the headset is on an active phone call any Buddy Intercom call reguest will be rejected automatically Once the phone call audio link drops you can initiate and accept Buddy Intercom calls TTS Text To Speech FUNCTION V1 headset has TTS function it can speak the number of incoming caller in English This function is the default you can close it by pressing VOL and VOL button together for 3 seconds To Resume Factory Default Mode Press and hold VOL and VOL key together for 3 seconds to resume factory default mode all bluetooth device will be cancelled BLUETOOTH AV DEVICE OPERATION 1 If AV not connected short press MC Button to connect last Bluetooth AV device 2 Short press MC Button to play or pause playback 3 Press and hold
8. duplex calls allow you to speak and hear the other party speak simultaneously Note The VO device do not support intercom communication NOTE The use of two speakers may be illegal in certain jurisdictions Please check the local regulations and act accordingly Headset Volume Up Charging Jack Volume CTRL Control Button Down Power On Power Off Intercom call MC Multi Connection Radio On Off Answer Call End Last Number Redialing Helmet clamp J aan Wall Charger Allen Wrench l f Velcro Pads Glue Plate MP3 Audio Cable Microphone Sponges User Guide The V1 or V2 is a water resistant device designed for use under mod erate rain or snow conditions However the headset is not water proof and should not be used under severe weather conditions The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device Make sure that the headset is fully charged for at least five hours before initial use 1 Connect the wall charger to the headset s Charging Jack located between the two Volume Buttons 2 While charging the Red Light turns on When charging is complete the Red Light will turn off a Intercom Connection STEP1 SET UP FOR BIKE TO BIKE INTERCOM PAIRING The V1 or V2 can be paired with up to two other headsets for intercom communication Pa
9. iring is a one time process Once the headsets are paired during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range NOTE The V1 or V2 allows you to speake via intercom to one Buddy headerset at a time BUDDY PAIRIG reguires two V1 or V2 headsets 1 If either headset is turned OFF press and hold the CTRL Button until the Red Blue light flashes alternately 2 Short press CTRL button it will search the other one which in pairing state and try to pair with it 3 Within a few seconds both headsets will turn off Red light and then begin flashing slowly in Blue thus pairing is finished 4 To pair with another headset repeat above steps NOTE If the Pairing process is not completed within one minute the headset will return to Standby mode STEP 2 SET UP FOR MOBILE PHONE CALLS PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the V1 V2 you must first pair your headset to the mobile phone Pairing is a once time process Once the headset is paired to a specific mobile phone during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range If the connection between the phone and headset is lost tap the CTRL button to reconnect the devices TO PAIR THE V1 V2 TO A BLUETOOTH MOBILE PHONE 1 Tune on your phone and make sure its Bluetooth
10. s until the Blue light begin rap idly alternating 3 Search for Bluetooth headsets on your GPS device by follow ing the device s instructions Please consult your GPS device s User Manual for more information 4 If your GPS device prompts for a PIN or Passkey enter 0000 four zeros Standard method 5 Your GPS device will confirm that pairing has succeeded The headset will begin flashing slowly in Blue 6 If you wish to use a Bluetooth mobile phone to make and receive calls through the headset you must now pair your mobile phone to your GPS device by following your GPS and or mobile phone s instructions MOUNTING THE HEADSET ON THE HELMET ATTACHING THE CLAMP TO THE HELMET The microphone speaker clamp must be mounted onto the left parts of the helmet Once mounted the headset unit can be attached or de tached from the microphone speaker clamp at any time There are two methods that can be used in order to attach the clamp onto the helmet Standard method Recommended for most helmet types Glue plate method Recommended for helmets to which the standard method cannot be applied using the Glue Plate included in the box 1 Use the enclosed Allen Wrench to loosen the two screws on the Back Plate 2 Slide the Back Plate between the internal pa ternal shell of the helmet 3 Adjust the clamp s location so that the microphone is located opposite the center of your mouth _ and then tighten the screws
11. t station on your headset Pressing Volume Up will search upwards higher frequency Pressing Volume Down will search downwards lower freguency Once a station is found searching stops and you can hear the station by simply plugging it to the Clamp s jack with the Mp3 cable as follows 1 Power on the headset to have it on Standby mode flashing slowly in Blue 2 Connect one side of the Mp3 cable to your Mp3 player audio device s jack and the other side to the Helmet Clamp s jack 3 Operate the Mp3 Player audio device by using its Buttons FF REW PLAY PAUSE Connect the Mp3 cable to the clamp s jack Aa
Download Pdf Manuals
Related Search
Related Contents
Filter clean - Découvrez SPLASH, la gamme piscine de Realco. EJC/EJC-Z 14/16 - LiftFinder.com Synology RackStation RS815 QUICK START GUIDE Operating Instructions Switch Butler DSE 409E Copyright © All rights reserved.
Failed to retrieve file