Inflator/Spotlight
Contents
1. attempt to connect items exceeding the 15 amp 12 volt rating Using the Inflator and a 12 volt DC item may exceed 15 amps and cause damage to the unit item and or accessories and will void warranty Therefore it is strongly recommended not to use both the 12 Volt DC Accessory Recharge Port and the Inflator at the same time Estimated 12 Volt DC Operation Time Appliance Estimated Power Usage Operating Time Watts hours Cell phone 1 20 120 talk time Fluorescent light 4 10 30 Radio fan depth finder 9 1 14 Camcorder VCR spotlight 15 1 8 Power tools bilge pump 24 15 Electric cooler 48 13 Car vacuum 80 0 5 1 Note All times are approximate and based upon a fully charged unit USING THE INFLATOR AIR COMPRESSOR The builtin 12 volt DC Inflator Air Compressor is the ultimate inflator for all vehicle tires trailer tires and sports inflatables The attached hose with standard tire valve connector chuck and three different sized nozzles are located in the compartment in the rear of the unit Each nozzle clips on the end of the standard tire valve connector attached to the free end of the inflator air compressor hose A WARNING The Inflator Air Compressor is capable of inflating up to 260 pounds per square inch PSI To avoid overinflating carefully follow instructions on articles to be inflated Never exceed recommended pressures Always check pressure with the pressure gauge Never leave the Inflator Ai2. is returned more than 30 days but less than one year from the purchase date manufacturer will repair the unit or at its option replace it free of charge If the unit is repaired new or reconditioned replacement parts may be used at manufacturer s option A unit may be replaced with a new or reconditioned unit of the same or comparable design The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period The customer is responsible for the shipping charges on all returned items after 30 days During the warranty period manufacturer will be responsible for the return shipping charges UMMATIONS This warranty does not cover accessories bulbs fuses and batteries defects resulting from normal wear and tear including chips scratches abrasions discoloration or fading due to usage or exposure to sunlight accidents damage during shipping to our service facility alterations unauthorized use or repair neglect misuse abuse failure to follow instructions for care and maintenance fire flood and Acts of God If your problem is not covered by this warranty call our Technical Support Department at 954 584 4446 or toll free at 866 584 5504 for general repair information and charges if applicable You may also contact us through our website at www vectorfg com STATE LAW RIGHTS This warranty gives you specific legal rights Some states do not allow limitations on how long an implied warranty
3. lasts or the exclusion or limitation of incidental or consequential damages so the exclusions or limitations stated herein may not apply This warranty gives the purchaser specific legal rights other rights which vary from state to state may apply TO REQUEST WARRANTY SERVICE FOR THIS PRO DUCT Contact Technical Support by telephone fax or mail see below We suggest that you keep the original packaging in case you need to ship the unit When returning a product indude your name address phone number dated sales receipt or copy and a description of the reason for return and product serial number After repairing or replacing the unit we will make every effort to return it to you within four weeks WARRANTY ACTIVATION Please complete Warranty Activation Card and mail to Vector Manufacturing Enter VEC270SB as Model and Inflator 1 000 000 Power Series Spotlight as Product Type All Vector products must be registered within 30 days of purchase to activate this warranty Mail the completed registration form along with a copy of the original sales receipt to USER S MANUAL amp WARRANTY INFORMATION TOLLFREE 866 584 5504 FAX 954 584 5556 IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS ATIN CUSTOMER SERVICE 4140 SW 30th Ave Ft Lauderdale FL 33312 WARRANTY IS NON TRANSFERABLE AND NON REFUNDABLE TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND THIS INSTRUCTIONAL MANUAL THIS MANUAL CONTA
4. INS IMPORTANT INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRO DUCT PLEASE RETAIN FOR FUTURE REFEREN CE 4140 S W 30th Ave Ft lauderdale FL33312 2005 VECTOR MANUFACTURNG Toll Free 866 5845504 MADE IN CHINA 8 VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page ii IMPORTANT SAFETY INSTRUCTIONS WARNINGS 1 2 6 7 There is a risk of explosive gases being released when lead acid batteries are being charged or discharged Failure to follow instructions may cause property damage explosive hazard and or personal injury Never look into or point the inflator air compressor nozzle or the spotiight toward anyone s eyes Do not use the inflator air compressor continuously for longer than 15 minutes Extended use will cause it to overheat and can damage the unit After 15 minutes of continuous inflator air compressor use turn the unit OFF and wait 15 minutes before resuming operation of the compressor DO NOT overinflate objects or exceed manufacturers recommendations for pressure on objects to be inflated Always monitor pressure using the pressure gauge Bursting articles can cause serious injury It is recommended to wear protective eyewear when inflating tires inflatable items NEVER submerge this unit in water When charging the unit near water do not allow electrical cords to become moist damp or wet electrical shock could result Never cover unit at any time Never leave
5. VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page 8 VEC270SB ecm WECTOR This limited warranty program is the only one that applies to this product and it sets forth all the T h e F ree d om of POWE R responsibilities of Vector Manufacturing regarding this product There is no other warranty other than those described herein a This Vector Manufacturing product is warranted to the original purchaser only to be free of defects in nfl aA to r S otl ht materials and workmanship for one year from the date of purchase without additional charge The warranty does not extend to subsequent purchasers or users Manufacturer will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances Incidental 1 0 0 0 j 0 0 0 Powe r Se ri es and consequential damages are specifically excluded from coverage under this warranty This product is not intended for commercial use This warranty does not apply to accessories or damage to 12 Volt DC Power Supply units from misuse or incorrect installation connection Misuse includes wiring or connecting to improper polarity power sources Cordless Rechargeable RETURN REPAIR POLICY Defective products other than accessories may be returned to manufacturer Any defective product other than accessories that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge If such a product
6. ay be substituted These can also be purchased from popular automotive parts suppliers nationwide You will need a Phillips screwdriver to replace the bulb HAIRPIN RETAINING WIRES 1 Remove the rubber bezel from the lens cover 2 Unscrew counterclockwise and remove the two Phillips screws located on either side of the lens 3 Carefully separate the lens guard lens glass and rubber gasket from the reflector 4 Gently lift the reflector and bulb assembly from the housing note that the wires are still attached to assembly 5 Unsnap the retaining wire from the reflector s flange by pinching the two ends together and lifting 6 Loosen the Phillipsthead retaining screw no need to completely remove to free the bulb assembly from the reflector 7 Slightly turn and lift out the bulb assembly from the back of the reflector 8 Disconnect the bulb assembly s white wire from the red power wire by separating the male spade terminal from the female terminal 9 Insert the replacement bulb assembly into the reflector flange 10 Reverse the proceeding procedure to reassemble the Spotlight 11 Press the Spotight s Power Pushbutton ON to test proper operation of spotlight Battery Replacement Disposal It is recommended that the unit be returned to Vector Customer Service for battery replacement Contains a maintenance free sealed non spillable lead acid battery which must be disposed of properly Recycling is req
7. ery rapidly 5 Monitor the pressure gauge When desired pressure is reached slide the Inflator Air Compressor Power Switch to OFF open thumb latch and remove connector from valve stem 6 Remove adapter from item and store along with the hose in the Inflator Hose Accessory Storage Compartment VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page 6 Typical Inflation Times Inflation pressure psi Approx Filling time Vehicle and trailer tires 155 80R 13 26 2 5 mn 185 70R 14 30 4 5 rin 235 75R16 30 6 5 mn 235 70R17 42 16 min Bicycle tires 27 X 1 racing 70 2 3 mn Sports Equipment Football 13 24 sec Basketball 10 20 sec Volleyball 5 6 sec A WARNING Always follow manufacturer s recommendations for pressure on item to be inflated CARE AND MAINTENANCE Replacement Parts Contact Vector s Technical Support Department toll free at 866 584 5504 or visit our website www vectornfg com for replacement parts including replacement adapters and cords and any additional information that you may need AAWARNING To reduce the risk of shocks or burns and avoid damage to the unit make sure all power switches are in the OFF position all adapters are unplugged and the unit has been allowed to cool down before performing any maintenance parts replacement Bulb Replacement The quartz halogen bulb assembly is available through Vector see contact information above A comparable 12 volt H3 25 watt bulb m
8. ge the unit every two months when it has not been used regularly e If the unit is used for an extended period after the red LED indicator lights recharging could take up to 20 hours and battery life may be shortened Notes Recharging the battery after each use prolongs battery life frequent discharges between recharges reduces battery life If unit is fully discharged it is recommended that the vehicle being used for recharging be left running while the unit is charged via the 12 volt DC method Viewing Battery Charge Level Status Press the Battery Charge Level Pushbutton to display charge level status The Battery Charge Level Indicator LEDs will light LEDs from left to right e One Red LED indicates a low battery charge e Two Red LEDs indicate a medium level or partially charged battery e Two Red and one Green LEDs indicates a full or high level battery charge 120 Volt AC Charging 1 Insert the supplied 120 Volt AC Recharging Adapter into the 120 Volt AC Recharge Adapter Barrel Connector Port located next to the Battery Charge Level LED Indicators 2 Plug the adapter into a standard North Armerican120 volt AC electrical outlet 3 Charge until two Red and one Green LEDs light 4 Once fully charged disconnect the adapter Note The unit cannot be overcharged using this method 12 Volt DC Charging 1 Insert the 12 Volt DC Recharging Adapter into the units 12 Volt DC Accessory Recharge Port 2 Insert the other end
9. hat may shorten the unit s working life protect it from direct sunlight direct heat and or moisture Check unit periodically for wear and tear Contact the Customer Service Department at 866 584 5504 to replace worn or defective parts Do not drop this unit as it may damage the product If unit is dropped or damaged please discontinue using it N ever disassemble take unit to a qualified service technician or call Vector Customer Service when service or repair is required Incorrect reassembly may result in a risk of electric shock or fire and will void the warranty Always replace the fuse with the sarre type and amp rating Never use a higher amperage fuse rating To reduce risk of damage to unit pull by plug and not the cord when disconnecting Disconnect all charging cords and turn all ON OFF switches to the OFF position before cleaning this unit THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS Read This User s Manual Before Using This Unit SAVE THESE INSTRUCTIONS VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page iv T TABLE OF CONTENTS IMIOGUCH ON e a saaa ka a a a a eo ee a AEA O E OR BES SE Pd E E AA 1 FERRON 2a 5 sls fa a E O EE A A a a E T A A A a E o E 1 AC and DCC hargimg Recharging s eede a a a AEE 3 Viewing Battery Charge Satus e sicc ea e aE e a a Aa E EE aaia 3 T20 VEAC Charging veea d mwa a a a eet Geta hol a ke eel as 3 12 VOIIDC CHARGING erenn ergs E Ra Se aes SY a
10. into the vehicle accessory outlet or other 12 volt DC power source 3 To check the charge level status of the battery during DC charging disconnect the DC adapter from the accessory outlet and push the Battery Charge Level pushbutton O bserve the battery charge indicator 4 When charging is complete disconnect the adapter A WARNING Do not recharge for more than 5 6 hours maximum using the 12 volt DC method 9 VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page 4 USING THE SPOTLIGHT The quartz halogen Spotlight is controlled by the Spotlight Power Pushbutton located on the side of the unit Make sure the Spotlight is turned OFF when the unit is being recharged or stored USING THE AUXILIARY LED AREA LIGHT The Auxiliary LED Area Light is controlled by the Auxiliary LED Area Light Power Switch located directly under the Area Light above the Spotiight Make sure the Area Light is tumed OFF when the unit is being recharged or stored USING THE UNITAS A 12 VOLT DC PORTABLE POWER SUPPLY This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory outlet plug and are rated up to 15 amps 1 Insert the 12 volt DC plug from the appliance into the units 12 Volt DC Accessory O utlet Recharge Port DO NOT EXCEED A 15 AMP LOAD 2 Switch on the appliance and operate as usual 3 Periodically press the battery charge level pushbutton to check battery status A WARNING Do not
11. r Compressor unattended while in use Bursting articles can cause serious injury A CAUTION Do not operate the Inflator Air Compressor continuously for extended periods of time approx 15 minutes depending on the ambient temperature as it may overheat In such event the Inflator Air Compressor will shut down and can be restarted after a cooling period of approximately 15 minutes Inflating Products With a Valve Stem 1 Place the standard connector chuck of the hose on the valve stem 2 Push connector toward the valve stem and close thumb latch Note Make sure connector is pushed onto valve stem as far as possible before closing thumb latch 3 Slide the Inflator Air Compressor Power Switch to ON 4 Monitor the pressure gauge When desired pressure is reached slide the Inflator Air Compressor Power Switch to OFF open thumb latch and remove connector from valve stem 5 Store the hose in the Inflator Hose Accessory Storage Compartment when not in use Inflating Products Without a Valve Stem Inflation of other itens requires use of one of the adapters nozzles 1 Insert appropriate adapter e g needle into the connector chuck on the Air hose and close thumb latch 2 Insert adapter e g needle into item to inflate 3 Slide Inflator Air Compressor Switch to COMPRESSOR 4 Refer to the following table for approximate filling pressure and time Small items such as volleyballs footballs etc inflate v
12. sf TEE Ree 3 Using sthe Spoui ght oie e a E E a avaikeins aptanaacs we eer e E tae ai a ean goat age a Meee os 4 Using the Auxiliary LED Area Light 0 200002 eee 4 Using the Unit as a 12 volt DC Portable Power Supply 00055 4 Estimated 12 Volt DC Operation Time 2 2 2 2 2 2 0202 ee ee 4 Using the Inflator Air Compresor aie cee ea aa ee EE Dee 5 Inflating Products With a Valve Stem 1 2 2 ee 5 Inflating Products Without a Valve Stem 0 000000 ee 5 Care and Maintenance sser cme ee a ee eee Rn ee dt eee 6 Replacement Parts ooo aaa ian date are A tee ete aid eel ae gh a al ete She 6 Bulb REDIACSIMEME ia a detehcten ea EN E Gh cain esta a Ne ERS EG aed ig BMG chide O A 6 Battery Replacement Disposal eee ee a ee ee 7 Fuse Replacement DC Accessory Adapter 000005 2 eee eee Fi SPECIMCAUOMS wie a a E a AE ee a ee Es EEE eae 7 INTRODUCTION Thank you for purchasing the VEC270SB Inflator 1 000 000 Power Series Spotlight This system is an advanced high pressure up to 260 PSI multi use air inflator system 1 000 000 power spotlight and 12 volt DC power source that will provide years of reliable service if maintained properly Please read this guide carefully before use to ensure optimum performance and avoid danage to the unit FEATURES Builtin inflator air compressor with pressure gauge hose and adapters Builtin ultra bright 12 volt halogen spotlight Long ife auxiliar
13. this unit unattended while operating CAUTIONS 1 10 11 Iz 13 When using an extension cord not supplied for AC charging recharging make sure it has the same configuration as the plug of the unit and that the cord is properly wired and in good condition The cord must be suitable for 120 volts AC and have a minimum 2 amp rating It is reconmended to use an outlet complete with a Ground Fault Interrupt GFI Switch Do not recharge for more than 5 6 hours maximum using the 12 volt DC method or more than 14 16 hours using the 120 volt AC method Recharge unit after each use using the recontrended 120 volt AC rrethod Avoid charging the battery at temperatures below 40 F 5 C or above 105 F 40 C All ON OFF switches should be in the OFF position when the unit is charging or not in use Make sure all switches are in the OFF position before connection to a power source Never operate the inflator with the 120 Volt AC Recharging Adapter connected to the unit as the charger could become damaged Do not use any accessory that is not recommended or provided by the manufacturer N ever insert anything other than the supplied or recommended accessories into this units 12 Volt DC Recharging Power Port N ever operate the inflator after the battery indicator light comes on Although this unit contains a nonspillable battery it is recommended that unit be kept upright during storage use and recharging To avoid possible damnage t
14. uired contact your RECYCL A local authority for information Failure to comply with local state and a a federal regulations can result in fines or imprisonment For more Cr PS C information on recycling this battery call toll free 877 288 7722 82L Fuse Replacement The VEC270SB contains a 15 amp blade fuse located in the Inflator Hose Accessory Storage Compartment You will need small needle nose pliers to replace the fuse 1 Open the Inflator Hose Accessory Storage Compartment cover 2 Grasp the blade fuse with the needlenose pliers and pull straight out 3 Replace the fuse with the same size and type SPECIFICATIONS Battery Type s Sealed high density AGM lead acid rechargeable maintenance free 6 volt DC 4 5 Amp hour Spotlight H3 25 watt bulb Accessory O utlet Protected by a 15 Amp Fuse DC Charger Adapter 12 volt DC DC AC Charger Adapter 120 volt AC 500mA 12 volt DC Output a
15. y LED area light 12 volt DC accessory outlet Includes 120 volt AC and 12 volt DC adapters LED battery charge level indicators Includes a nonspillable maintenance free heavy duty sealed battery e Requires no maintenance other than recharging for optimum operation Rubberized base and easy grip handle e Protective rubber safety guard bezel around lens Tough durable molded highimpact housing VEC270SB_Manual_062105 qxd 6 23 05 5 24 PM Page 2 OMNAURWNR e e e O 12 Volt Halogen 1 000 000 Power Series Spotlight Auxiliary LED Area Light Auxiliary LED Area Light Power Switch Rubberized Easy grip Handle Battery Charge Level LED Indicators Battery Charge Level Pushbutton 12 Volt DC Accessory O utlet Recharge Port 120 Volt AC Recharge Adapter Barrel Connector Port Spotlight Power Pushbutton Inflator Air Compressor Power Switch Inflator Hose Accessory Storage Compartment 12 13 Analog Dial Pressure Gauge 20 Air Hose with Standard Tire Connector Chuck _ AC AND DC CHARGING RECHARGING FULLY CHARGE THE UNIT USING THE 120 VOLT AC CHARGING METHOD FOR A FULL 14 TO 16 HOURS BEFORE FIRST USE For maximum battery life we recommend the unit be kept fully charged at all times If the battery is allowed to rermain ina discharged state battery life will be shortened e MAKE SURE ALL SWITCHES ARE TURNED OFF DURING RECHARGING e Recharge the unit fully after each use and rechar
Download Pdf Manuals
Related Search