RSC-820CLS Roll Laminator Owner`s Manual
Contents
1. Ololoolo1010 O O O RSC 820CU CLS 6 CONTROL PANEL When the machine is initially turned on the LED display window will show the speed at 1 2 RS SE an Control Buttons 1 SPEED DISPLAY Display s current Speed 2 SPEED BUTTON Adjusting the speed of the rollers To change the speed of the rollers press the up or down arrow button 3 RUN To start the rollers 4 STOP To stop the rollers 9 REV To reverse the rollers press and hold the REVERSE button ARSE eset 7 ROLLER NIP SETTING It is important to adjust the roller nip settings to the appropriate thickness of the board being used Use the guide below to adjust to the correct position NOTE If you don t want to laminate please place the pressure lever to the Open position NO 5 RSC 820CU CLS 8 USING FOOT PEDAL USING FOOT PEDAL Place the foot pedal on the floor in front of the machine Once all correct settings are displayed you may use the foot pedal to operate the laminator for Hands Free Operation To activate the machine press the foot pedal once and then release Repeat to stop the rollers 9 LOADING FILM The cross cutter is located on the rear exit table of the machine 1 After lamination move the cutter approximately to the center of the completed application at the desired point of detachment Figure 1 2 Grasp film with one hand press the cutter downward into th2. 5 13 lt s m 11 MAINTENANCE Cleaning the Body of the laminator 1 To clean the machine body dampen a cloth with water only and gently wipe the machine clean Removing Adhesive Build Up 1 Remove the film from the laminator 2 Use a damp water only cloth and a rubber gum eraser to remove the adhesive on the Teflon metal and silicone rollers Note Rub firmly but do not scrub the rollers vigorously as this may scratch the surface Do not use sharp metal objects steel wool or abrasives as these may also damage the rollers Lubrication 1 Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease lithium grease after 6 months or 1000 hours of operation whichever comes first 12 TROUBLESHOOTING Possible Solution a Plug the power cord into appropriate a Power plug is not plugged in outlet Machine will not turn b Power switch is in 0 Off position b Put the power switch to the I On on c Tripped circuit breaker position d Blown main power fuse c Reset the circuit breaker d Replace the fuse There is power but the a Emergency switch es is are engaged rollers are not turning after the RUN button is pressed a Disengage the emergency switch es b Properly install the paper guide so that the micro switch is activated d Replace the motor fuse b Paper guide is not installed correctly c Blown motor fuse AN T
3. rseu royalsovereign com E mail sales royalsovereign com RS Canada Inc RS International Australia PTY LTD 1025 Westport Crescent Mississauga On L5T 1E8 CANADA 30 Prime Drive Seven Hills NSW 2147 Australia TEL 1 905 461 1095 FAX 1 905 461 1096 TEL 61 2 9674 2127 TF 1 866 961 6673 FAX 61 2 9674 2027 E mail info ca royalsovereign com E mail salesaust royalsovereign com 16
4. ASE Speris OWNER S MANUAL RSC 820CL CLS Laminator Read all instructions carefully before use For any Customer Support needs please choose the Customer Support tab on www royalsovereign com Royal Sovereign International Inc www royalsovereign com lt AS TABLE OF CONTENTS TOPIC PAGE Ia late Ditto ini i i a i i 3 2 Safety Precautions nio ainiai i ved i i i is i aa 3 32 NS IAA o atsisiust i i i i i k nant 4 4 Included with Laminator oo Wo Wc Woo W W mma 5 5 Producer identic anO siira m OTT 6 eM Control Panel aa o ST 7 rM Roller Nip SS an i one 8 8 Using Foot Pedal ainiai E EE a i 9 Sa INN Ne o I si a ij TET 9 10 Threading Film TOT Decais e T E E S 10 12 T2 MOURIR esra as asa ai o iai a i i ia 13 Ti MOntenAN CE mean I Ba Da a e si i a 14 12 ITOUDIGSODHEIG bei ee suns Gi ease e i ai aa E esa 14 13 SPG AAA AE AA 15 Ta LE sia ai ai ni a i i i i i ia ni i a 16 RSC 820CU CLS 1 INTRODUCTION Thank you for choosing a Royal Sovereign laminator It has been designed and manufactured to provide years of continuous service For complete operating and maintenance information please read this manual thoroughly Upon receipt of your laminator please inspect the box the machine and all other contents for shipping damage Damage should be brought to the immediate attention of the delivering carrier See page 5 for list of shipment elements 2 SAFETY PRECAUTIO
5. NS Failure to comply with any of the following safety procedures could result in serious injury Please read the instructions carefully and keep for future reference 1 Only a licensed electrician should install wiring and outlet for the laminator 2 Ensure the unit is plugged into a properly grounded outlet with the correct voltage 3 Keep hands and clothing i e Neckties away from rollers The rollers have pinch points that can trap body parts or clothing and cause serious injury Keep flammable and wet objects away from the machine Place machine on a level surface Avoid excessive sunlight humidity and extreme temperatures QU ER ME uem Ensure the unit is turned off cooled and unplugged from the outlet prior to moving and or repairing 00 Keep out of reach of children 9 Only Royal Sovereign authorized maintenance and service technicians should make repairs 10 Do not attempt to laminate items that exceed total recommended material thickness for the unit 11 When cleaning the machine don t use flammable sprays or materials 12 Do not touch the rollers when they place foreign objects inside the machine lt ARS 8S5 eios 3 INSTALLATION Note The laminator should be installed by a trained service technician The laminator comes fully assembled except for the stand to avoid shipping damage Upon arrival thoroughly inspect the unit It is imperative that any shipping damage is reported and a c
6. ai a Upward curi a Loosen the top roll film tension b Downward curl b Loosen the bottom roll film tension 14 RSC 820CU CLS 13 SPECIFICATIONS Unit dimensions 1045 x 540 x 470 mm 1045 x 540 x 1100 mm w x d xh Carton dimensions 1280 x 770 x 600 mm 1280 x 770 x 700 mm w x d xh Gross Weight 80kg 100kg 15 Pp ARS 85 8 sioe 14 WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One 1 year for Parts and Labor from the date of installation excluding lamination rollers which are warranted for Six 6 months This warranty is extended only to the original purchaser This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended Royal Sovereign s sole and exclusive liability and the customer s sole and exclusive remedy under this warranty shall be at Royal Sovereign s option to repair or replace any such defective part or product These remedies are only available if Royal Sovereign s examination of the product discloses to Royal Sovereign s satisfaction that such defects actually exist and were not caused by misuse neglect attempt to repair unauthorized alternation or modification incorrect line voltage fire accident flood or other hazard All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the equipment was
7. e application and slide it first to one end of the application then to the other end to complete the cut Figure 2 amp 3 Figure 3 Pp RS Aaaa 10 THREADING FILM TAKE UP X Pa COLD FILM ROLLER N UPPER IDLE BAR PAPER BACK LOWER IDLE BAR p IDLE BAR 10 1 Decaling 1 Turn the power switch on P position The Power switch is located on the rear left side of the unit 2 Complete the steps as in the LOADING FILM section see page 10 3 Take off the Feed Table 4 Pull the top film down over the Safety Cover to the bottom of the craft paper mounting film 5 Align and center the craft paper mounting film to the top film and tighten the two lower core screws Figure 1 Figure 1 10 RSC 820CU CLS 6 Thread the top film underneath the Upper Idle Bar Figure 2 7 Tape the top film on to the Release Liner Take Up Figure 2 8 Cut and separate the release liner and the film Figure 3 9 Make the craft paper pass the support idle bar and round the lower idle bar Figure 4 10 Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller do not use the Lower Idle Bar for Mounting Figure 6 Figure 5 11 Pp RS ipe UE 11 Reinstall the Feed Table and close the Safety Cover 12 Adjust the nip setting to appropriate gap 13 Insert and push the leader board until they reach the front ni
8. laim is filed with the delivering carrier immediately upon receipt The laminator should be located in an area with adequate work space for feeding graphics and lamination materials Avoid placing the laminator in a dusty area or near sources of extreme heat or cold Once the laminator is in place lock the casters into position ON position Always unlock the casters OFF position when moving to a different location ELECTRICAL REQUIREMENTS Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance with electrical codes in your area The laminator should have a dedicated power line MODEL RSC 820CL CLS 220 240V 120V 220 240V 120V socer 50 60HZ 50 60HZ 50 60HZ 50 60HZ single phase 120V UL 230V UL 240V UK 220V EU 220V AU 4 RSC 820CU CLS INCLUDED WITH LAMINATOR Thoroughly inspect the parts and the unit It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment 3 Owner s Manual 7 Spare Motor Fuse FUSE 50T 6 3A Spare Main Power Fuse FUSE 65TS SA E foua ARS Sian 9 PRODUCT IDENTIFICATION PART NAME RSC 820CL CLS SAFETY COVER FEED TABLE MAIN ROLLER FOOT PEDAL TENSION CONTROL KNOBS PRESSURE LEVER CONTROL PANEL UPPER IDLE BAR RELEASE LINER TAKE UP STAND gt O c o NN OA EB O NN
9. originally purchased Model serial number and date of delivery are required for all claims The warranty made herein is in lieu of all other warranties expressed or implied including any warranty or merchantability or fitness for a particular purpose Royal Sovereign will not be liable for personal damage or personal injury unless primarily caused by its negligence loss of profit or other incidental or consequential damages arising out of the use or inability to use this equipment LIMITED WARRANTY This warranty specifically does not cover damage to laminating rollers caused by knives razor blades or any sharp objects or abrasives or failure caused by adhesives or damage caused by lifting tilting or improper use of the machine Warranty repair or replacement by Royal Sovereign or its authorized Reseller s does not extend the warranty beyond the initial one year period from the date of installation Unauthorized customer alterations will void this warranty CORPORATE HEADQUARTERS Royal Sovereign International Inc 2 Volvo Drive Rockleigh NJ 07647 U S A TEL 1 800 397 1025 FAX 1 201 750 1022 E mail info 9 royalsovereign com RS Holland B V Royal Sovereign Inc lt Oversea Sales Office Industrieweg 6K 4104AR Culemborg The Netherlands 1001 World Meridian II 426 5 Gasan dong TEL 31 0 345 473 097 Geumcheon gu Seoul 153 759 KOREA FAX 31 0 345 519 811 TEL 82 2 2025 8800 FAX 82 2 2025 8830 E mail
10. p point 14 Push the Run button Figure 7 15 Push the leader board into the rollers Figure 7 16 Adjust the top and bottom tension knob by rotating it clockwise or counterclockwise Turn it until the top and bottom roll films have some resistance The tension varies depending on the film thickness the thicker the film the more tension is required Figure 8 Figure 8 17 Press the Stop button when the leader board has completely exited from the rollers 18 Use the Cross Cutter to cut the leader board from the web see page 9 19 Set the nip setting to the appropriate position for the Over lamination Decaling application 12 RSC 820CU CLS 10 2 Mounting 1 Lay the decaled image face down on a flat surface Carefully peel back and put a crease along the edge of the release liner Approximately 1 inch or 25mm Figure 1 Figure 1 2 With the image facing up align the image onto the board Press firmly from the center out Figure 2 3 Adjust the pressure lever to ensure the proper opening Figure 3 4 Flip the image over the upper roller and hold on to the release liner Figure 4 Figure 4 5 Press the foot pedal once and then let it go while slowly pulling the release liner as the board enters the main roller nip Figure 5 BL P Press the foot pedal once again when the board has completely exited from the rear of the unit Trim the board if necessary Figure
Download Pdf Manuals
Related Search