Electronic double knob cylinder OMEGA 815 DK
Contents
1. Please refer to the following chapter Operating the door lock on how to commission the locking cylinder 40 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Operating the door lock Operating the door lock Correct door operation ATTENTION Damaging the double knob cylinder by false door operation possible gt Use only the door handle for opening and closing the door like shown in the illustration gt Don t open gt Don t the door open the with the door with key the knob Electronic double knob cylinder OMEGA 815 DK M 41 Operating the door lock CEStronics E The locking cylinder is equipped with a reader which enables you to operate the door lock from the outside To operate the door lock from the outside you need a locking medium that is authorized for this locking cylinder Please refer to the enclosed Programming Instructions on how to authorize locking media Mifare locking media gt Move with your authorized locking system 1 into the reading range of the locking cylinder This range is about 20 mm The reader module in the outside knob identifies the locking medium The locking cylinder sends a short signal to signal the enable status During the opening time you can open the door During this opening time the locking cylinder does not respond to any other locking media gt To open the door lock rotate the outside knob2. gt Only use the tool specified for this purpose gt Insert the fixing screw into the door lock and initially screw it in only until it is flush with the striking plate Do not yet tighten the fixing screw at this point This will enable you to verify that the follower moves without friction after the fitting of the locking cylinder has been completed mie 34 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Fastening the outside knob to the cylinder body Once the cylinder body has been fitted in the door lock the outside knob must again be attached to the cylinder body Proceed as follows Thread the connection cable 1 through the opening 2 at the bottom of the outside knob A Electronic double knob cylinder OMEGA 815 DK M 35 Fitting the locking cylinder in a door lock CEStronics E gt Push the outside knob onto the shaft at the cylinder body gt Hand tighten the two screws in the interior of the outside knob with the combination tool hexagon socket screwdriver 36 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Installing the reader module in the outside knob After the outside knob has been fastened to the cylinder body you can again insert the reader module into the outside knob Proceed as follows gt Push the plug of the
3. Electronic double knob cylinder OMEGA 815 DK M 11 For your safety CEStronics Remarks This mounting and fitting instructions are only valid for e CEStronics electronic double knob cylinder 815 DK M Manufacturer The manufacturer of the locking cylinder is CEStronics GmbH Friedrichstr 243 42551 Velbert Tel 49 0 2051 204 0 Fax 49 0 2051 204 105 www ces eu Service For support in case of service please contact your CEStronics partner 12 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Introduction Introduction Description The electronic double knob cylinder 815 DK M is part of the OMEGA system It is based on Mifare transponder technology This locking cylinder has a freely rotating knob Access is granted after an authorized transponder has been held in front of the knob The locking cylinder may not be used for outdoor application The locking cylinder is intended for installation in locks prepared for profile cylinders The installation of the locking cylinder does not require any additional effort and no wiring is required at the door The locking cylinder can only be operated with authorized locking media You authorize a locking medium for your locking cylinder with Master media see page 15 Optional Master media To operate the locking cylinder you move an authorized locking medium within reading range of the outside knob The reader module in the outside knob recog
4. Electronic double knob cylinder OMEGA 815 DK M 57 Emergency opening CEStronics E gt Push the reader module back into the sleeve of the outside knob gt To fasten the reader module hand tighten the two opposite screws with the combination tool three square screwdriver gt Replace the battery of the locking cylinder after each emergency opening see page 47 chapter Replacing the battery of the locking cylinder 58 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Care The outer accessible parts of your locking devices such as knobs knob sleeves covers fittings etc can be cleaned with a soft slightly moist wipe NOTICE Risk of damage to surfaces of the OMEGA FLEX cylinder Never use solvent containing cleaning agents to avoid damage to your locking devices Maintenance gt Have the locking cylinder serviced and its perfect functioning verified every six months by CEStronics or by a CEStronics partner only vw Replace the batteries in line with a defined maintenance schedule vw Make sure to have replacement batteries ready in good time Spare Parts The locking cylinder does not require any spare parts for you to change gt If you need service please contact your professional CES partner Electronic double knob cylinder OMEGA 815 DK M 59 Trouble shooting CEStronics amp Trouble shooting Symptom The door lock cannot be open
5. Electronic Security Systems Declaration of Conformity We the manufacturer CEStronics GmbH Electronic Security Systems Friedrichstra e 243 D 42551 Velbert Germany Phone 49 0 2051 204 444 Fax 49 0 2051 204 245 declare on our own responsibility that the product Name Double knob cylinder Type OMEGA Mifare Product 815DK M 715DK M 615DK M in all varieties and types is in compliance with following standards 1999 5 EC R amp TTE directive 2004 108 EC EMC directive 2006 95 EC Low voltage directive Applied standards EN 300 220 1 V2 2 1 2006 04 EN 300 220 2 V2 1 2 2006 04 EN 300 330 1 V1 5 1 2006 04 EN 300 330 2 V1 3 1 2006 04 EN 301 489 1 V1 8 1 2008 04 EN 301 489 3 V1 4 1 2002 08 EN 60950 1 2006 11 A technical documentation for the product is fully available from the manufacturer The infor mation provided in the user information is available Velbert 2009 07 28 Dipl Ing Richard Rackl Managing Director CEStronics GmbH Bankverbindung Siz der Gesellschaft Velbert Zertifizierung nach Friedrichstra e 243 D 42551 Velbert Deutsche Bank Registergericht Amtsgericht Wuppertal DIN EN ISO 9001 Telefon 02051 204 0 Fax 02051 204 105 BLZ 330 700 90 Kto 4703088 Register Nr HRB 18895 E Mail info ces tronics de Gesch ftsf hrer TUN Nr 4046437000004 Ein Unternehmen Internet www ces eu Eckhart Leptien Dipl Ing Richard Rack Ust IdNr DE 614236458 der CES Gruppe
6. Instructions near the locking cylinder Make sure you are using the latest version of this 1 manual The manual is available free of charge at www ces eu To prevent danger to life and limb the following safety instructions must be observed Danger to life e Do not use the locking cylinder for doors with anti panic function such as escape doors for which a knob cylinder is not permitted Otherwise people may not be able to open the door in emergencies and may be injured or killed e Only use the locking cylinder for door locks for which knob systems are permitted In case of doubt please contact the manufacturer of the door or the door lock and satisfy yourself that the locking cylinder is suitable for your door system Danger of explosion e Live parts of the RF Master Set may cause an explosion Do not use the RF Master Set in potentially explosive atmospheres Electronic double knob cylinder OMEGA 815 DK M 5 For your safety CEStronics E Danger of suffocation e Never allow children to play with packaging material and or plastic bags There is a risk that children pull them over their head and suffocate Danger of poisoning Always keep the locking cylinder out of reach of children There is a risk that children swallow small parts such as batteries or screws Danger of property damage To prevent property damage the following safety instructions should be observed e Always have repairs perfor
7. ces eu CEStronics GmbH Friedrichstra e 243 D 42551 Velbert 49 0 2051 204 0 49 0 2051 204 229 _info ces tronics de CESlocks GmbH Mettmanner Str 119 D 42549 Velbert 49 0 2051 204 0 49 0 2051 204 229 _info ces locks de CESrom srl Str Metalurgistilor 3 D RO 550137 Sibiu 40 0 269 206 00 2 amp 40 0 269 206 00 5 _info ro ces eu CES Austria Repr sentanz sterreich Cesar A Carcamo 43 0660 7320311 amp 43 0732 210022 2681 office beschlaege cc www beschlaege cc a CEStronics E CESfrance SARL 8 Impasse Charles Petit F 75011 Paris 33 0 1 44 87 07 56 33 0 1 43 07 35 78 info fr ces eu www ces eu fr ame CESnederland B V Lage Brink 9 NL 7317 BD Apeldoorn 31 0 55 52 66 89 0 31 0 55 52 66 89 9 _infonl ces eu www ces eu nl CESitalia srl V d vecchie Fondamenta 4 Stra e d A Gr ndungen 4 I 39044 Egna Neumarkt BZ 39 0471 812 294 39 0471 812 294 info it ces eu www ces eu it CES Security Solutions Ltd Unit 6 8 Revenge Road GB Lordswood Chatham Kent ME58UD 44 0 1634 673301 44 0 1634 673326 info uk ces eu www ces eu en CES MIDDLE EAST A G P Advanced German Products LLC Authorized General Distributor of CES in Middle East PO Box 102761 UAE Dubai 971 0 4 369 7051 971 0 4 390 8935 info agp dubai com www agp dubai com fa
8. locking cylinders from CEStronics Versions and their functions The shield is available in the following versions Type Functions N NoTime programming with programmer programming without time zones and events T Time programming with programmer programming with time zones and events NET With RF modul for use within CEStronics RF networks In preparation N V NoTime in virtual network programming without time zones and events Time in virtual network programming with time zones and events Key Point T V 20 Electronic double knob cylinder OMEGA 815 DK M CEStronics Introduction Scope of delivery gt Before fitting and commissioning please check the contents of the package and the scope of delivery gt Check new devices for transport damage and inform your dealer promptly if any damage is found e Reader module with beeper Light ring Fastening screws for the reader module Outside knob Fastening screws for the outside knob Flexprint cable for the connection between the inside and the outside electronics Cylinder body Follower Electronics module with battery compartment Q Inside knob 11 Battery Type Power one Varta PowerOne Panasonic Industrial Lithium CR 2 Lithium 3 0 V 850 mAh 12 Special fixing screw Overview Va IE BOON Electronic double knob cylinder OMEGA 815 DK M 21 Introduction CEStronics E Ai Tools Fitting
9. result in personal injury or even death gt Always satisfy yourself that the RF Master Set is suitable for your door system gt Only fit the locking cylinder in door locks for which knob systems are allowed gt Contact the manufacturer of the door or the door lock in case of doubt A DANGER In case of malfunctions it may not be possible to open the door in emergency situations which could result in personal injury or even death gt Never fit the locking cylinder in doors with anti panic function such as escape doors gt Only fit the locking cylinder in door locks for which knob systems are allowed Unpacking the locking cylinder gt Take the locking cylinder from the package and remove all packaging material such as films padding and packaging board 24 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Note on fitting the cylinder Q a The locking cylinder may be damaged by the ingress of rain water The IES may be damaged by the ingress of rain water gt Ensure that the door is not exposed to driving rain Do not leave the door open when it is raining IP 54 Protection against touching with tools wires etc protection against internal dust accumulation protection against splashing water from any direction gS As an option your locking cylinders ar
10. CEStronics E Electronic double knob cylinder OMEGA 815 DK M Fitting and Operating Instructions Translated fitting and operating instructions version 1 61 03 2013 Preface CEStronics E These Fitting and Operating Instructions will help you fit and use the electronic double knob cylinder 815 DK M locking cylinder e as intended e safely and e advantageously Any person who e fits e programs e operates or e disposes of this locking cylinder must have read and understood the entire contents of these Fitting and Operating Instructions These Fitting and Operating Instructions should be kept near the locking cylinder at all times Notes on the layout In these Fitting and Operating Instructions various elements are highlighted with defined layout features so you can identify at a glance whether a passage contains standard text e alist or gt individual steps in a sequence of actions Notes highlighted with this symbol contain additional 1 information on the efficient use of the locking cylinder 2 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Contents Preface unuanunnanunnanunnanunnanunnanunnannnnannnnannnnannnnannnnannnnannnnn 2 Notes on the layout unuanunnannnnannnnannnnanunnannnnannnnannnnannann 2 Contents anuannannonnannonnannannunnannunnunnunnunnnnnunnnunnannannannannen 3 For your Safety nuanunnanunnannnnanunnannnnannnnannnnannnnannn
11. Flexprint connection cable into the socket at the reader module as shown in the figure gt Observe the correct fitting position of the connection cable Electronic double knob cylinder OMEGA 815 DK M 37 Fitting the locking cylinder in a door lock CEStronics E gt Push the clamping bridge in the direction of the arrow onto the clamp joint to lock the clamp joint ATTENTION The connection cable may be damaged when the reader module is inserted into the outside knob gt Always push the reader module into the outside knob slowly and carefully gt Make sure that the connection cable is neither kinked nor squeezed 38 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Push the connection cable carefully into the outside knob and insert the reader module into the outside knob Push the reader module into the outside knob until you feel the stop 1 Rotate the reader module while exerting a slight pressure in the direction of the arrow 2 OL Electronic double knob cylinder OMEGA 815 DK M 39 Fitting the locking cylinder in a door lock CEStronics gt To fasten the reader module hand tighten the two opposite screws using the combination tool three square screwdriver gt Rotate the inside knob so as to verify the easy movement of the follower If the follower moves easily hand tighten the fixing screw
12. aid box for combination tool Combination tool three square hexagon socket key TORX bit for fixing screw 14 m flat wrench Belt grip uhwWN BE B The combination tool the flat key and the TORX bit are supplied with the RF Master Set The tools are 1 also available independent of the RF Master Set and can be ordered separately 22 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Fitting the locking cylinder in a door lock ATTENTION The locking cylinder may be damaged if not fitted properly gt Only skilled personnel may fit the locking cylinder This personnel must have been trained on the product by CEStronics or a CEStronics partner gt Before fitting verify that the cylinder body has the correct length for the door lock by measuring the thickness of the door leaf and the length of the cylinder body The locking cylinder is supplied preassembled and with the battery inserted Before fitting the locking cylinder must first be disassembled The following tools are required for the disassembly and the fitting e combination tool e screw driver with TORX bit e fitting aid e 14 mm flat wrench Electronic double knob cylinder OMEGA 815 DK M 23 Fitting the locking cylinder in a door lock CEStronics A DANGER In case of malfunctions it may not be possible to open the door in emergency situations which could
13. atteries Always remove leaked batteries immediately from the device Clean the terminals before inserting new batteries There is a danger of acid burns through battery acid Remove flat batteries directly from the device Be sure to send back the batteries to orderly disposal Electronic double knob cylinder OMEGA 815 DK M CEStronics E For your safety Explanation of the safety notes These Fitting and Operating Instructions include safety notes of the following types A DANGER DANGER notes warn against hazards that may directly result in severe or fatal injuries A CAUTION CAUTION notes warn against hazards that may result in slight or medium injuries Attention ATTENTION Attention notes warn against possible property or environmental damage Electronic double knob cylinder OMEGA 815 DK M 9 For your safety CEStronics amp Intended use The locking cylinder serves to lock and unlock doors with locks for which knob systems are permitted It is exclusively intended and may only be used for that purpose The knob of the locking cylinder must not be used for opening the door Any other use is considered to be improper and may result in property damage or even personal injury CEStronics GmbH does not accept any liability for any damage resulting from improper use 10 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp For your safety CE Declaration of Conformity CES
14. e also 1 available with a weatherproof outside knob Please contact your professional partner Electronic double knob cylinder OMEGA 815 DK M 25 Fitting the locking cylinder in a door lock CEStronics E Removing the reader ATTENTION The locking cylinder contains sensitive electronic components that may be damaged or destroyed through static charges Do not disassemble the RF Master Set in rooms with a high built up static charge The reader module is fitted in the outside knob and fastened to the outside knob with two screws Proceed as follows to remove the reader module ATTENTION The Flexprint connection cable attached to the reader module may be damaged when the reader module is pulled out gt Always pull the reader module slowly and carefully out of the outside knob gt Avoid mechanical strain on the Flexprint cable gt Make sure not to squeeze the Flexprint cable 26 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock gt Release the two opposite screws on the outside knob with the combination tool three square screwdriver These screws cannot be completely screwed out but will always be held in the outside knob ATTENTION The connection cable attached to the reader module may come off when the reader module is pulled out gt Be sure to exercise caution when pulling the module out of the outside knob E
15. e outside knob with the combination tool hexagon socket screwdriver ATTENTION The connection cable attached to the reader module may be damaged when the outside knob is pulled off gt Always pull off the outside knob slowly and carefully 30 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock Fitting the cylinder body The cylinder body is inserted into the profile cylinder hole of the door lock CAUTION The door may accidentally close while you are fitting the cylinder and it may not be possible to open the door again gt Secure the door against accidental closing gt Ensure that a locking medium authorized for this cylinder is available gt Make sure that the authorizations for the I locking cylinder concerned are granted correctly Please refer to the enclosed Programming Instructions for information on how to authorize a locking medium To check the position of the door fitting and the door lock proceed as follows gt Remove the lids of the fitting aid on both sides gt Insert the fitting aid 1 into the profile cylinder hole 2 until it projects on both the inside and the outside of the door lock Electronic double knob cylinder OMEGA 815 DK M 31 Fitting the locking cylinder in a door lock CEStronics If the fitting aid can be inserted smoothly in the profile cylinder hole you can continue wit
16. ecurity mode can be used in other systems 3 requiring this type of transponder This ensures the multi application capability of the locking medium 44 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Operating the door lock DESFire EV 1 in standard mode Locking media operating in the standard mode behave like any other ISO 14443 transponders For authorization the UID of the locking medium is used If you manage your systems with the CEStronics software you can use both DESFire EV 1 variants with the CEStronics software gt Move your authorized locking medium into the reading range of the fitting This distance is about 20 mm I Q Max 20 mm t The reader module in the outside knob identifies the locking medium The locking cylinder sends a short signal to signal the enable status During the opening time you can open the door During this opening time the locking cylinder does not respond to any other locking media gt To open the door lock rotate the outside knob in the corresponding direction 2 gt Release the knob immediately after the door has been opened You do not have to turn the knob back into its original position If you are using a locking medium that is not authorized to enable this locking cylinder the light ring of the locking cylinder flashes red four times and you hear four successive beeps In this case the outside knob is not coupled with the follow
17. ed although a locking medium is held in front of the outside knob Possible cause and remedy The locking medium is not authorized for this cylinder Use an authorized locking medium The battery is empty Replace the battery of the locking cylinder with a new one see page 47 The locking medium is not within the range of the reader in the outside knob of the locking cylinder Hold the locking medium nearer to the outside knob If the door lock still cannot be opened please contact your CEStronics partner 60 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Disposal Neither the locking cylinder nor the batteries nor parts of the locking cylinder may be discarded with the normal household waste Ask your local authorities about recycling and or the proper disposal of the device in line with environmental regulations Used batteries should be delivered at a collection centre ATTENTION Incorrect disposal from empty batteries possible gt Be sure to send back the batteries to orderly disposal Electronic double knob cylinder OMEGA 815 DK M 61 Technical data CEStronics E Technical data e e E Q Q e ere 1 Outside locking side 2 Inside knob side 62 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Dimensions of outside knob Dimensions of inside knob Power supply Number of locking media Number of master media Permissible
18. ening time your locking device allows free access e For locking cylinders this is the period during which the knob is coupled with the follower time e For wall terminals this is the period during which the relay is pulled up When the locking cylinder or access terminal detects the TIME MASTER it starts beeping at one second intervals The number of beeps determines the opening time 16 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Introduction Programming with OMEGA software You can also control and manage your locking systems online via a radio frequency link or via the programming cable The following components are required for this system e State of the art standard PC No 1 2 with Windows XP or Windows 7 operating system 1 GHz processor or higher at least 1 GB of RAM at least 1 GB of free hard disk space e Network interface card with TCP IP protocol for the installation with Access Points e CD ROM drive for installing the software from data media e One free USB port for the use of the programming cable optional e Existing Internet connection for using OMEGA Quicksupport e Monitor with a resolution of 1 024 x 768 pixel or higher or a resolution of 1 024 x 600 pixel netbook e CEStronics Suite software e A valid licence for CEStronics Suite software e OMEGA MIfare RF NET Access Point No 3 maximum of ten devices per Access Point e At least one locking device No 4
19. er The outside knob rotates freely but the door lock cannot be operated Q Electronic double knob cylinder OMEGA 815 DK M 45 Transport notes CEStronics E Transport notes Locking cylinders may interact if they are placed too close to one another or too close to locking media This will discharge the battery To prevent interaction between cylinders during transport please observe the following notes gt Always keep locking cylinders at least 5 cm apart gt If this is not possible remove the battery of the locking cylinder please refer to page 47 gt Do not transport locking cylinders together with ID cards or locking media gt If this is not possible remove the battery of the locking cylinder please refer to page 47 gt Only transport locking cylinders with the reader fitted gt If this is not possible remove the battery of the locking cylinder please refer to page 47 46 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Replacing the battery of the locking cylinder Replacing the battery of the locking cylinder When the Low Battery alarm sounds the battery of the locking cylinder must be replaced The Low Battery alarm starts sounding when the battery capacity is falling In this case you will hear a very long beep with every locking attempt The battery is inserted in the electronics module in the inside knob To replace the bat
20. gt Carefully pull off the cover in the direction of the arrow ATTENTION The battery the housing of the electronics module and or the electronics may be damaged if you try to pry out the battery with an object gt Only use your hand to remove the battery gt Do not use any objects for this purpose Electronic double knob cylinder OMEGA 815 DK M 49 Replacing the battery of the locking cylinder CEStronics E gt Put your finger lightly on the contact plate 1 to prevent the battery from being pushed out gt Carefully release the catch 2 in the direction of the arrow until the contact plate is loose Remove the contact plate 50 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Replacing the battery of the locking cylinder Take the battery out of the battery compartment Insert the new battery with the correct polarity into the battery compartment Electronic double knob cylinder OMEGA 815 DK M 51 Replacing the battery of the locking cylinder CEStronics A CAUTION Incorrectly inserted batteries may cause irreparable damage to your locking cylinder Always insert the batteries with the correct polarity into your locking cylinder gt Ifa battery has been inserted incorrectly have the locking cylinder checked by a CEStronics partner Only use batteries of the CR2 type Lithium with 3 V Reinstall the contact plate o
21. h the installation of the cylinder body If not proceed as follows gt gt 32 Pull the fitting aid out of the profile cylinder hole Correct the position of the door lock If required contact the manufacturer of the lock Again check the position of the door fitting and the door lock using the fitting aid Insert the connection cable 1 from the inside into the open end of the fitting aid 2 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock gt Pull the fitting aid out of the profile cylinder hole from the outside gt Insert the cylinder body into the profile cylinder hole of the door lock gt Rotate the inside knob to verify that the follower can move free of friction gt If the movement of the follower is impeded by friction remove the cylinder body again from the profile cylinder hole gt Verify the proper functioning of the door lock gt If the door lock does not operate properly please contact the lock manufacturer gt Repeat the steps described above to fit the cylinder body Electronic double knob cylinder OMEGA 815 DK M 33 Fitting the locking cylinder in a door lock CEStronics E ATTENTION If a drilling machine or a cordless screwdriver is used to fasten the locking cylinder the locking cylinder may be damaged gt Do not use a cordless screwdriver or drilling machine for fitting the RF Master Set
22. in rooms in which the humidity does not exceed 95 Do not use the locking cylinder in rooms with a high level of dust formation Do not use the locking cylinder near sources of heat The outside knob may only be exposed to temperatures between 25 C and 70 C The inside knob may only be exposed to temperatures between 0 C and 50 C Danger of malfunctions The reading units in the locking cylinder must not be covered with any metallic material Electronic double knob cylinder OMEGA 815 DK M 7 For your safety CEStronics E Notes on the handling of batteries Keep batteries out of reach of children If a battery was swallowed consult a physician without delay Always insert new batteries Never insert old and new batteries at the same time Never mix the battery types Always replace batteries by batteries of the same or an equivalent type Before inserting the batteries check that the terminals in the device and at the batteries are clean Clean them if necessary Observe the correct polarity when inserting the batteries Never attempt to recharge non rechargeable batteries There is a risk of explosion Never short circuit the batteries Always store batteries at a cool dry place Direct heat may damage the batteries Do not expose any battery powered devices to strong sources of heat Never throw any batteries into a fire If you do not use your devices for a longer period take out the b
23. in the corresponding direction 2 gt Release the knob immediately after the door has been opened You do not have to turn the knob back into its original position 42 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Operating the door lock If you are using a locking medium that is not authorized to enable this locking cylinder the light ring of the locking cylinder flashes red four times and you hear four successive beeps In this case the outside knob is not coupled with the follower The outside knob rotates freely but the door lock cannot be operated Electronic double knob cylinder OMEGA 815 DK M 43 Operating the door lock CEStronics DESFire EV1 Transponder locking media You use DESFire EV 1 locking media in two different modes DESFire EV 1 in security mode optional Locking devices and locking media operating in the security mode 1 are manufactured exclusively by CEStronics and programmed with individual keys and special firmware The data transmission between the locking device and the locking medium is encrypted Only locking media that are authenticated by the device are authorized to lock or unlock This ensures a very high protection against manipulation These locking devices 1 will not accept any foreign transponders 2 they do not respond to any locking or unlocking attempt with other locking media A DESFire EV 1 locking medium manufactured by CEStronics operating in the s
24. lectronic double knob cylinder OMEGA 815 DK M 27 Fitting the locking cylinder in a door lock CEStronics E gt Pull the reader module out of the outside knob until you feel the stop gt Now push the reader module back into the outside knob by about 5 mm 1 and rotate the reader module in the direction of the arrow 2 gt Take out the reader module carefully 28 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Fitting the locking cylinder in a door lock The reader module is connected with the electronics module of the inside knob by a connection cable Flexprint This connection cable is plugged in at the reader module The plug is locked by a clamping bridge To release the connection proceed as follows gt Carefully pull the clamping bridge in the direction of the arrow 1 to release it from the socket of the reader module gt Now pull the plug of the connection cable out of the socket of the reader module 2 gt Note the fitting position of the connection cable Electronic double knob cylinder OMEGA 815 DK M 29 Fitting the locking cylinder in a door lock CEStronics E Releasing the outside knob from the cylinder body The outside knob is fastened to the cylinder body with two screws These two screws are arranged in the interior of the outside knob To release the outside knob from the cylinder body proceed as follows gt Release the two screws in the interior of th
25. lling the reader module in the outside knob 37 Operating the door lock nuzauanunnanunnannnnanunnanunnanann ann 41 Correct door Operation essensenennennenn nun eset eee eee nennen nennen 41 Transport notes uuuuunnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 46 Replacing the battery of the locking cylinder 47 Lost master or locking medium z zanunuanannanannanan nn 54 Emergency Opening z zanunuanannanannanannanannanannanannanan namen 55 CAM PPRPEREERTPERRSFFERLRTEEFTEEFELERTRERTERFERFERREECFEERFEFERRERFEFLERERLERTFER 59 Maintenance unuanunnanannanannanunnanunnanannanannanannanannanannanen 59 Spare PartS uuunnnnnnnnnnnnunnunnnnunnnunnnunnnunnnunnnunnnunnnunnnunnnn 59 Trouble shooting zananuananunnununnanunnanunnanunnannnn ann n anne 60 DiSPOSal PEPELTLETFEFUFFERLPETTTERFELTLETEFRELFERFETTELESLERTERLTERTTTRTRLEFTTIT 61 Technical data zauanuananunnanunnanunnanunnanunnannnnanunnannnn anne 62 GIOSSANY an nase a aan enden 64 Overview of the signals zuzauanunnanunnanunnanannanunnanan nun 65 Notes on the manufacturer s warranty unuunnnannannannanen 68 4 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp For your safety For your safety A Basic safety instructions Observe all warnings and notes in these Fitting and Operating Instructions when fitting programming and using the locking cylinder Always keep these Fitting and Operating
26. locking cylinder IES wall terminal e Programming cable No 5 optional Electronic double knob cylinder OMEGA 815 DK M 17 Introduction CEStronics E Setting up a online radio network Setting up a system for wireless manual programming For further information please refer to the User Manual of the CEStronics Suite which is available free of charge at www ces eu 18 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Introduction System components You can purchase various locking media from a 1 CEStronics partner to match your specific requirements Qo 3 7 j p PROGRAM Ma MASTER 7 ARE a CEStronics CEStronics CEStronics Bectronic Security System 1 Locking media You can operate the locking cylinder with the following locking media e transponder key e key fob e key fob slimLine e card 2 Locking cylinder 3 SYSTEM MASTER The SYSTEM MASTER is used to authorize the PROGRAM MASTERS for the system Each system has one and only one SYSTEM MASTER 4 PROGRAM MASTER The PROGRAM MASTERS are used to authorize locking media to operate the locking cylinder Electronic double knob cylinder OMEGA 815 DK M 19 Introduction CEStronics E amp You can combine mechanical locking cylinders and 1 RF Master Sets and or access terminals in one and the same locking system In this case you can use transponder keys for both mechanical and electronic
27. med by properly qualified personnel e Only use accessories and spare parts recommended by CEStronics e Do not use any drilling machines or cordless screwdrivers when fastening the locking cylinder e Only use the proper tools to open the locking cylinder e When fitting the locking cylinder make sure that the lock and the plate rose are in a perfect condition Malfunctions of the lock may impair the functioning of the locking cylinder e Make sure that the cylinder can be inserted through the profile cylinder hole of the plate rose and the lock without jamming and without using force during the installation If this is not possible align lock and plate rose so as to prevent jamming and or bending of the locking cylinder during its installation e Do not use any lubricants or oils for the locking cylinder e Do not drop the locking cylinder on the floor on hard surfaces or on hard objects e Protect the electronic components of the locking cylinder against water and other liquids 6 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp For your safety The locking cylinder contains highly sensitive electronic parts that may be damaged or destroyed through static charges Do not disassemble the locking cylinder in rooms with built up static charge Danger through environmental conditions Do not use the locking cylinder in corrosive atmospheres chlorine ammonia lime water Only use the locking cylinder
28. n the battery compartment 52 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Replacing the battery of the locking cylinder Push the inside knob again onto the electronics module m vw Satisfy yourself that the sealing gasket sits perfectly on the thread of the electronic module vw Manually screw on the cover clockwise rotation vw Tighten the cover with the flat key vw Apply the flat key behind the inside knob as shown in the figure vw Fit the cover again ES Electronic double knob cylinder OMEGA 815 DK M 53 Lost master or locking medium CEStronics E Lost master or locking medium ATTENTION An unauthorized person may gain possession of a Master medium and manipulate the locking system gt Always keep all Master media at a safe place gt Make sure that these are not accessible to unauthorized persons ATTENTION When a Master medium is lost the potential finder may manipulate the locking system gt If a Master medium has been lost have the locking cylinder and or the access terminal only initialized by persons trained on the product by CEStronics or a CEStronics partner During an initialization all authorizations for this locking cylinder are deleted gt If one of the locking media is lost please contact a CEStronics partner 54 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Emergency openi
29. nannnnannnnn 5 A Basic Safety instructions cccccececeseeeeeeeeeeeeeeeaeeneeaes 5 Notes on the handling of batteries cccccceeeeeeeeeeeeaeenes 8 Explanation of the safety notes ccccceseteeeeeeeeeeeeeeeeeeeeenes 9 Attention ae ee id 9 Intended use u ae 10 CE Declaration of Conformity cceeeee ee eee ann namen 11 REMARKS vias saws aan 12 Manufacturer saenaennnnnnnnnnnnnnen nen nn nun nun nun nun nun nun nun nennen 12 SEI VICE rennen 12 Introduction zanunnanannanannanannanannanannanannanannanannanunnannnn 13 Description an een 13 Optional Master media cceeeee eee ee ee nn nun en eee namen 15 Programming with OMEGA software nusessnnerannennnnen an 17 System components ensensensennennnnnannnnnan san nun nun nun nun nenne 19 Versions and their functions essesseneenennnnnnnnnnnn nennen nennen 20 Scope OF CELIVELY aan ni 21 Electronic double knob cylinder OMEGA 815 DK M 3 Contents CEStronics Fitting the locking cylinder in a door lock zuznuanunnanen 23 Unpacking the locking cylinder 4 u4444R Hrn nenn ern 24 Note on fitting the cylinder 2z4u4444R Her eee ee tees ann nam 25 Removing the reader uss4 u rennen ainin eaea nig 26 Releasing the outside knob from the cylinder body 30 Fitting the cylinder body cceccecceceee eset eee nn nun nun nn nn nennen 31 Fastening the outside knob to the cylinder body 35 Insta
30. ng Emergency opening If the battery is empty you can connect an Emergency Power Supply with the locking cylinder to provide the required voltage To open the door you also require the authorized locking medium to confirm that you have authorized access The Emergency Power Supply is not part of the scope of delivery of the locking cylinder To order it please contact your CEStronics partner ATTENTION When the module is pulled out of the outside knob the connection cable attached to the reader may be damaged gt Always pull the module out of the outside knob slowly and carefully Electronic double knob cylinder OMEGA 815 DK M 55 Emergency opening CEStronics E gt Release the two opposite screws on the outside knob with the combination tool three square screwdriver These screws cannot be completely screwed out but will always be held in the outside knob 56 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Emergency opening Pull the reader module out of the outside knob until you feel the stop 1 Connect the Emergency Power Supply with the interface 2 on the reader module Observe the notes and instructions in the Operating Instructions of the Emergency Power Supply Use your authorized locking medium to open the door After you have opened the door disconnect the connection between the reader module and the Emergency Power Supply
31. nizes your authorized locking medium In response the outside knob and the follower are coupled and the door can be opened by rotating the outside knob All Mifare transponder media and media according to ISO 14443A and DESFire EV1 can be programmed at the locking cylinder and used as authorized locking media Mifare locking media are read within a reading range of about 20 mm The locking cylinder responds to various events during programming operation and maintenance with different visual and acoustic signals The locking cylinder can be programmed manually with the appropriate transponder cards SYSTEM MASTER PROGRAM MASTER optional Master cards see page 15 Chapter Optional Master media Electronic double knob cylinder OMEGA 815 DK M 13 Introduction CEStronics E Features of the locking cylinder A freely rotating knob Mifare Classic transponder technology Optional 868 MHz radio frequency Integrated evaluation unit with memory for Up to 1000 transponder keys Up to 3000 events with date and time at correct programmed time Reading distance of up to 20 mm Six different Master media available as an option to increase the functionality of the cylinder see page 15 ff Online programming via additional OMEGA Mifare software not included in the scope of delivery Interface for emergency power supply Two colour LED light ring for visual signalling Beeper for status indication and feedback The numbe
32. pening you need an Emergency Power Supply Recess in the door lock for accommodating a profile cylinder Master medium that is authorized to program locking media Medium enabling you to lock and unlock an electronic locking cylinder A master medium that enables you to authorize PROGRAM MASTERS for the system Each system has one and only one SYSTEM MASTER A transponder is a wireless communication and control device that receives signals and automatically responds to them 64 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Overview of the signals Overview of the signals Normal operation with locking media Meaning Signal type Signal Authorized access Beeper 1 x short LED green 1 x short Unauthorized access Beeper 4 x short attempt LED red 4 x short Programming with Master media Meaning Signal type Signal Start of programming Beeper 1 x short LED green On as long as medium is within range End of programming Beeper 1 x long LED green On as long as medium is within range Acknowledgement of programming Beeper LED green 1 x short On as long as medium is within range Acknowledgement of deletion Beeper LED green 2 x short after 2 s On as long as medium is within range programming Unauthorized Beeper 2 x short programming attempt LED red 2 x short Error message in case Beeper 1 x long of incorrect LED red 1
33. r of possible locking media is not restricted to 1000 An extension of the internal 1 locking media table is possible but leads to performance penalties 14 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Introduction Optional Master media Optional Master media allow you to set additional functions manually without requiring additional aids such as a PC or programmer SYSTEM MASTER OMEGA MIFARE SYSTEM MASTER CEStronics Ch Electronic Security System The SYSTEM MASTER grants all authorizations on the highest level For each locking system there is one and only one valid SYSTEM MASTER With the SYSTEM MASTER you can authorize up to ten PROGRAM MASTERS In its basic version a locking system requires one SYSTEM MASTER and one PROGRAM MASTER each to program your locking devices The SYSTEM MASTER is also used to authorize the following additional Master media for your locking cylinders and wall terminals e TIME MASTER PROGRAM MASTER OMEGA MIFARE PROGRAM MASTER CEStronics GS Electronic Security System The PROGRAM MASTER is used to authorize and delete the authorization of your locking media Electronic double knob cylinder OMEGA 815 DK M 15 Introduction CEStronics E TIME MASTER OMEGA MIFARE TIME MASTER CEStronics Ch Electronic Security System With the TIME MASTER you set the opening time of the locking cylinder or access terminal During the op
34. rouble and error messages Meaning Signal type Signal Low Battery warning Beeper 1 x long after unlocking attempt LED red 1x long Motor blocked when Beeper 8 x short uncoupling LED red 8 x short Motor blocked despite Beeper 10 x short authorization LED red 10 x short Electronic double knob cylinder OMEGA 815 DK M 67 Notes on the manufacturer s warranty CEStronics Notes on the manufacturer s warranty As stated in our Standard Terms and Conditions the manufacturer s warranty does not extend to the following types of damage e damage to outer mechanical parts and damage resulting from normal wear and tear e damage as a consequence of external events or influence e damage as a consequence of improper operation e damage as a consequence of omitted maintenance work e damage as a consequence of excess voltage e damage as a consequence of fire water or smoke All technical data and features are subject to changes without notice The information and data contained in this document are subject to change without notice Without the express written permission by CEStronics no part of this document may be copied or transmitted for any purpose 2011 CEStronics GmbH Velbert Germany Part no BRO2201 002 68 Electronic double knob cylinder OMEGA 815 DK M C Ed Schulte GmbH Zylinderschlo fabrik Friedrichstra e 243 D 42551 Velbert 49 0 2051 204 0 49 0 2051 204 229 info ces eu www
35. temperature at outside knob Permissible temperature at inside knob Prohibited atmospheres Service life of the locking cylinder Service life of the battery Data transfer Reading area CE Certification Technical data Length approx 40 mm Diameter approx 36 mm Length approx 46 mm Diameter approx 36 mm Battery Type Power one Varta PowerOne Panasonic Industrial Lithium CR 2 Lithium 3 0 V 850 mAh max 1000 expandable max 100 at Master Mode max 1 SYSTEM MASTER max 10 PROGRAM MASTERS 25 C to 70 C 0 C to 50 C Not suitable for use in corrosive atmosphere chlorine ammonia lime water According to DIN EN One year at 80 locking cycles per day 30 000 locking cycles Encrypted 128 Bit AES approx 20 mm EN 300 220 1 EN 300 330 1 EN 301 489 1 EN 60950 1 Electronic double knob cylinder OMEGA 815 DK M 63 Glossary CEStronics E Flexprint Reader module Master media Emergency Opening Profile cylinder hole PROGRAM MASTER Locking medium SYSTEM MASTER Transponder Connection cable between the reader module in the outside knob and the electronics module in the inside knob of the locking cylinder The reader module is installed in the outside knob of the locking cylinder It identifies locking media Media for programming the RF Master Set Opening of the electronic locking cylinder in case of a flat battery For emergency o
36. tery the locking cylinder must be pulled out slightly so that you can apply the flat key to release the cover Proceed as follows ATTENTION The door cannot be opened again once the battery is completely empty gt Always replace the battery after the first Low Battery alarm ATTENTION Incorrect disposal from empty batteries possible gt Be sure to send back the batteries to orderly disposal If the battery is completely empty the door must be opened with an Emergency Power Supply see page 55 Chapter Emergency Opening In RF mode you do not have to re set the time of day as the current time will be transmitted by the OMEGA software mie mie Electronic double knob cylinder OMEGA 815 DK M 47 Replacing the battery of the locking cylinder CEStronics E ATTENTION The housing of the electronics module or the electronics of the locking cylinder may be damaged gt Only use batteries of the CR2 type with 3 V To replace the battery the locking cylinder must be pulled out slightly so that you can apply the flat key to release the cover Proceed as follows gt Apply the flat key behind the inside knob as shown in the figure gt Use the belt grip to release the cover gt Release the cover of the inside knob by counter clockwise rotation 48 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Replacing the battery of the locking cylinder
37. x long Electronic double knob cylinder OMEGA 815 DK M 65 Overview of the signals CEStronics E Enabling and disabling the Office function Meaning Signal type Signal Enabling with locking Beeper 1 x long medium LED green 1 x short Disabling with locking Beeper 1 x short medium LED green 1 x long Programming in radio network Meaning Signal type Signal Enabling RF mode Beeper 1 x short after leaving LED green reading range On as long as medium is within range Disabling RF mode Beeper 1 x long after leaving reading range LED green On as long as medium is within range Acknowledgement of Beeper 2 x short disabling of RF mode Data transmission LED green 1 x very short Programming TRACE signal good LED green 2 x very short TRACE signal still LED green 1 x very short usable TRACE signal bad LED red 1 x short 66 Electronic double knob cylinder OMEGA 815 DK M CEStronics amp Overview of the signals Programming with RF Master Set Meaning Signal type Signal Enabling learning mode Beeper 1 x short after leaving reading range LED green On as long as medium is within range Disabling learning mode Beeper 1 x long after laving reading range LED green On as long as medium is within range Learning mode enabled LED green 1 x short Acknowledgement of LED green 1 x long learning mode T
Download Pdf Manuals
Related Search