The JA-80Y GSM communicator
Contents
1. 5 28 Defining the delay before data is resent to an ARC The communicator tries to send reports to the main number IP address and if unsuccessful it then tries the backup number IP The JA 80Y GSM communicator address If still unsuccessful it then tries to re send the data to both the ARCs again as before but after a period defined by 06 ax where a 1 ARC1 2 ARC2 t isthe period 0 immediately 1 to 9 1 to 9 minutes Factory default setting 1 min for both ARCs 5 29 ARC communication checking period The time to wait after the last report sent to an ARC before performing an ARC communication check is set by this sequence The communication checking event code is 31 see 5 27 This sequence programs how often the communication check is performed 07a hhmm where a 1 ARC1 2 ARC2 hh hours mm minutes Notes e Checking reports are not sent in service mode e IP CID protocol allows very frequent checking of ARC communication e g every 5 minutes Factory default setting 24 hours after the last report for both ARCs 5 30 Enable ARC reporting ARC2 backs up ARC1 This sequence allows reporting to ARCs to be switched on off and also enables ARC2 to backup ARC1 00 ax where a 1 ARC1 2 ARC2 x O off 1 0n 2 ARC2 backs up ARC1 2 can only be entered for ARC2 Note if ARC2 backs up ARC1 then it will only receive data if it is not p2. 8 MFJ55304 The telephone numbers M1 and M8 will also receive the GSM provider s replay e If only uu u follows the CREDIT instruction no xx yyy zz then periodic balance checking will not be performed but the balance will be checked immediately and the uu u checking instruction will be memorized so that in future it will be possible to check the balance just by sending the instruction code CREDIT Example sending the SMS instruction code credit 101 7 50 1 causes the credit balance to be checked every 7 day after the SMS has been sent and if the balance starting with the first character in the message from the GSM provider is lower than 50 currency units it will be reported Warning the use of prepaid cards in the communicator is risky Some GSM providers block cards with enough credit but which are not topped up frequently enough We strongly advise the use of tariffed SIM cards 5 18 Remote programming by the SMS instruction Instruction PRG can be used to send programming and operating sequences to the alarm system code _PRG_seq seq seq where code is valid access or service code e g 8080 or 1234 space seq programming sequence usually set via the keypad Note e In the sequence can be used characters 0 to 9 and e When the valid instruction is received communicator simulates entering the keys on the keypad comma in the SMS is taken as a pause in the sequence entering e System must be u
3. If this number calls the communicator generates digit after the first ring as if it had been entered manually on the system keypad This toll free remote control by unanswered calls enables the following functions according to the digit stored at the end after the of the tel number in memory 1 setting the complete system ABC keypad button 2 setting section A A button 3 setting sections A amp B or B B button 8 PGX turns on for 2 sec if PGX is programmed for the pulse function 9 PGY turns on for 2 sec if PGY is programmed for the pulse function Notes if a phone sends no caller identification data it cannot be used for this type of remote control by phone if phone calls end before the control panel answers remote control is for free a phone which is pre authorized for toll free remote control can also temporarily authorize its keypad to fully operate the system see 3 3 just let it ring until the control panel answers the call if it is desired that the phone which is authorized for toll free remote control should not receive event reports then turn the reports off for that tel number see 5 4 setting arming with 1 2 and 3 will work only if enabled in the control panel 4 Reporting to phones Instruction Function Note The communicator can report events occurring in the Oasis system by SET setting arming setting or unsetting the same way as sending
4. Temporarily authorizing a phone keypad to be a system keypad It is possible to operate the system remotely by temporarily authorizing a phone keypad as follows 1 MFJ55304 a dial the system s SIM card number if a phone is connected to the communicator s simulated line it will start ringing b after 25 seconds of ringing programmable the system will answer with a short beep c key in a valid access code on the telephone keypad e g 8080 or 1234 if factory default settings are still valid d the phone keypad will behave as a system keypad and an acoustic signal in the receiver will indicate the control panel status 7 beep SET 2 beeps UNSET 3 beeps Service mode 4 beeps incorrect code entry siren sound alarm e now the system can be operated from the phone keypad the same way as from the system keypad including the commands starting with for example 81 to turn the PGX output on f to exit this mode simply end the phone call if nothing is entered within a minute the phone call will end automatically anyway Notes do not enter sequences on the phone too fast each key signal needs a certain time to be sent it depends on the particular phone and the quality of the GSM connection a fixed line phone can also be used to operate the system remotely the same way the phone must use tone dialling the system can also be operated from the keypad of a phone connected directly to the communicator s
5. These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked These parameters cannot be programmed from the system keypad but they can be programmed by sending SMS instructions or by Comlink software The JA 80Y GSM communicator oe MFJ55304 5 1 Language setting Language of the text used by the communicator can be set by instruction 981 xx Where 01 EN English 10 Fl Finnish 02 CZ Czech 11 NO Norwegian 03 SK Slovak 12 SV Swedish 04 NL Dutch 13 FR French 05 DE German 14 HU Hungarian 06 PL Polish 15 RU Russian 07 DA Danish 16 TR Turkish 08 IT Italian 17 SP_ Spanish 09 PT Portuguese Note Set the language before editing the text in the system change of the language will change the text to the factory default Change of the language in the communicator will automatically result in changing the language in the connected keypad also the wireless keypad if connected Set language will not be change when reset is performed Example by setting 98102 the Czech language will be set Factory default 98101 English 5 2 GSM signal strength measurement Good quality GSM signals are necessary for the reliable functioning of the communicator Entering 922 starts GSM signal measurement The keypad then displays the signal strength in the range 1 4 to 4 4 and me
6. another one and the former one used a PIN code first switch the control panel to service mode and enter 920 0 to erase the former PIN code The SIM card can then be changed Note The PIN code cannot be changed if the ARC settings are locked Factory default setting The PIN code is erased 5 23 GPRS log in parameters GPRS data communication wireless Internet via a GSM network is used for remote access via the Internet and also for IP reporting to the ARC To use GPRS data it must first be enabled activated in the SIM card contact your GSM provider for details Then the GSM network s GPRS parameters must be programmed by sending the following SMS instruction to the communicator code _GPRS_ x x y y Z Z where code is a valid master user or service access code e g 8080 or 1234 E space x x APN Access Point Name A comma y y username do not enter if not required Z Z password do not enter if not required Notes Most public GSM networks only request an APN do not enter y y and z z parameters in this case The GPRS parameters can only be programmed if the system is in service mode and the ARC settings are not locked Factory default setting APN Internet 5 24 ARC phone numbers IP addresses Events can be reported to up to 2 ARCs which can be independent or ARC2 can work as ARC1 s backup Each ARC can have its main and backup phone numbers or IP addresses programmed with Main 01ax
7. 168 001 123 08080 0 8 signifies an IP address it must have 12 digits followed by a 5 digit port number Entering 01p 0 or 02p 0 will erase the number address a 1 ARC1 a 2 ARC2 zz z ID number max 8 digits 0 to 9 and 1 A to 6 F hexadecimal number a 1 ARC1 a 2 ARC2 x 0 CID x 1 SMS CID x 2 IP CID a 1 ARC1 a 2 ARC2 ec event code see 5 27 x 1 report x 0 no report a 1 ARC1 a 2 ARC2 x 0 to 9 min O immediately without delay 0000 CID all events are reported came E 2400 24 hours after last report hhmm hours and minutes after last report a 1 ARC1 a 2 ARC2 x 0 reports disabled x 1 reports enabled x 2 only for ARC2 ARC2 backs up ARC1 x 0 no only records ARC communication faults if communication checks are enabled x 1 yes all reports except communication checks ARC reporting disabled IP address and port in format e g 013 8 192 168 021 123 08080 0 8 mark IP address which must contain 12 digits followed by 5 digits for the port Entering 0130 IP erase the setting xx X an installer defined locking code 4 to 8 digits Entering this code and then exiting service mode will lock the ARC settings 9010 will erase the code permanently unlocked 77 104 220 129 7070 img jablotron com ARC programming can be temporarily Xx x the locking code used by sequence enabled in service mode by entering this 901 sequence It will then relock on exiting service mode
8. Code 4G Code S518 Faultnolongerpresent_ 14 Device 302 Code dT 347 Code Ss 519 Mains dropout over 30 minutes 15 Device 303 Code 348 Code st 520 Mains dropout 16 Device 304 Code id 349 Code CC d SS21_ Mains recovery _ 17 Device 305 Code HO Code 522 Dischargedbattery 18 Device 306 Code 400 System status 523 BatteryOK 19 Device 307 Code OT Set 524 Switching to Service Mode Ca Dere 308 code fas easy see Tra J 21 Device 309 Code 403 Exit delay PGX 22 Device 310 Code 404 Entrance delay S27 PGY __ O 23 Device 311 Code OS Alarm 528 Radiojammingpresent_ 24 Device 312 Code 406 Service mode 529 Internal communication fault 25 Device 313 Code S 407 Maintenance mode 530 Internal comm restored _ 26 Device 314 Code 408 Partial setting 531 Communicationtest_ 27 Device 315 Code 409 Discharged battery 532 Unconfirmed alarm _ _ 28 Device 316 Code 410 Tamperalarm OTT SET 29 Device 317 Code 411 Alarm memory 602 UNSET __ o O 30 Device 318 Code a fT Faut OB STATUS 31 Device 319 Code 413 Powerfaut 604 MEMORY 32 Device 320 Code 414 Unknown status 605 PGXON U O 33 Device 321 Code aS Time OG PGXOFF _ __ 34 Device 322 Code dt tS Lastevent OZ PGYON i O 35 Device 3
9. GSM provider In addition a new way of SIM card balance checking is now available for networks which do not support standard balance checking but provide SMS reporting after each charged transaction In this case you can configure credit interrogation by sending the following SMS code _CREDIT_S_xx where code is a valid master or service code e g 8080 or 1234 is a space S is literally S or s a distinguishing mark XX automatic checking period in days optional Simultaneously it is necessary to disable SMS forwarding and to configure the number used to maintain SIM card validity the SIM validity maintenance call number After performing the configuration you can check the balance anytime by sending the CREDIT instruction By specifying the xx part you also request the checking to be performed automatically On each check the communicator performs a charged call to the SIM validity maintenance call number and enables the forwarding of a single SMS from the network operator to the first pre programmed number Notes e f the reported credit balance is lower than the set limit yyy the credit balance message from the provider will be forwarded to phone numbers M1 and M8 to remind someone to top up the SIM card e f event 22 is programmed to be reported to any tel numbers M1 to M8 then the message Discharged battery of the communicator will be sent to these numbers if the credit balance is under the yyy limit
10. SMS reports and or by calling phone numbers with an acoustic i if the used code is entered on the signal mostly used as audible notification of an SMS to be read Reporting UNSET unsetting system keypad If the system is can be programmed for up to 8 phone numbers disarming etna in the desired mode it will not The most frequently desired reports are already assigned to the telephone number memories by factory default so you only need to program tel STATUS int sa ene eon oe numbers to the particular memories which have the desired reports already imerrogation MS1 and MS2 assigned If desired other events can be reported to the number too i e the MEMORY last event The last event recorded In the control list of event reports assigned to the number can be changed see 5 4 interrogation panel memory Factory default reports assigned to the numbers M1 to M8 PGX ON turns on PGX the PG output has to be programmed M Reports PGX OFF turns off PGX for the function on off by 237 247 or 1 PGY ON turns on PGY 2 Second switching by 238 248 z Alarms and faults by SMS PGY OFF turns off PGY 3 Alarms and faults by SMS phone call if you answer the AUX ON turns on AUX turns a pair of AUX terminals on the 4 call you hear a siren sound AUX OFF turns off AUX communicator module on off 5 Alarms by SMS a phone call with Setting Unsetting CREDIT SIM card credit it has to be initialised by SMS before it 6 and faults by SMS only interrogation can fun
11. e If your ARC does not allow SMS CID or IP CID protocols please contact a Jablotron distributor for details on how to update your ARC Factory default setting Contact ID for both ARCs 5 27 Selection of events to report to ARCs The system recognizes 32 different types of events see the following table This sequence allows you to select which events are reported to which ARC 05 aec x where a 1 ARC1 2 ARC2 ec event code 01 to 32 xX 0 no report 1 report Factory default setting all events are reported Intruder alarm instant Intruder alarm delayed Fire alarm Panic alarm Number of permitted incorrect code entries exceeded Alarm triggered during control panel power up Tamper alarm End of tamper alarm End of alarm indication Alarm cancelled by user Setting Unsetting Partial setting Codeless setting External communication fault External communication restored Fault Fault no longer present Mains dropout longer than 30 minutes Mains dropout Mains restored Discharged battery Battery OK Switching to Service Mode Leaving Service Mode PGX ON OFF PGY ON OFF Radio communication jamming present Internal communication fault Internal communication restored Communication test Unconfirmed alarm Besides the events listed above the communicator also reports some events which are not selectable here e g the annual inspection request if enabled in the control panel CID 1393
12. phone calls e GSM signal strength measurement e simulated phone line functionality e the digits of the emergency tel number 7 5 Remote access by Internet The system can be accessed remotely via www GSMLink cz which allows complete programming by installers and also operating the system by end users To access the system remotely it is necessary to e Use a SIM card enabled for GPRS data transfer e Program the communicator GPRS parameters APN also possible via www GSMLink cz e Register the communicator via the GSMLink web page by o displaying www GSMLink cz and selecting New registration o setting your login details name and password o entering the communicator registration code see 5 19 o entering the communicator SIM card tel number o entering your system access code user or service this gives you access to the user menu or the installer menu accordingly o after entering the above parameters it should be possible to establish a connection with the system connecting takes time depending on network traffic typically within 2 minutes e for further access sessions you only need to enter your login details these can be memorized by your web browser e several people can register for internet access to the system both installers and users 11 MFJ55304 e A service technician needs only one set of login details to access various installations After the first system has been registered the installer
13. provided with the communicator The SIM card used in the communicator must be GPRS enabled and the GPRS parameters must be programmed in the communicator too see 5 23 When the communicator s GPRS modem function is used e It is possible to make phone calls but the internet data transfer rate will drop to zero during phone calls e Incoming SMS messages are stored and are processed after GPRS data transfer has been terminated e GPRS data transfer is terminated if the communicator is due to report alarms or setting unsetting by SMS or by phone call The JA 80Y GSM communicator 7 Further guidance on the communicator 7 1 How the communicator sends reports If there is a need to report an event e g an alarm then the communicator e sends data to ARC1 if used the communicator tries the main phone number IP address if unsuccessful then it tries the backup number IP address e Then it sends data to ARC2 in the same way if programmed as an independent ARC If ARC2 is programmed as the backup to ARC1 then the data will only be sent to it if transfer to ARC1 has been unsuccessful e Then the unit sends SMS reports 1 tel number 2 tel number 8 tel number e Then the unit performs reporting by phone call 1 tel number 2 tel number 8 tel number each programmed number is called once whether the call has been answered or not e If all previous attempts to send data to ARCs have been unsuccess
14. 01489 1 ETSI EN 301489 7 EN 55022 EN 50130 4 ETSI EN 301419 1 and EN 301511 ETSI EN 300 089 V3 1 1 2000 12 ERC DEC 98 20 21 Radio transmissions CLIP protocol caller ID SMS Can be operated according to Note Although this product does not contain any harmful materials we suggest you return the product to the dealer or directly to the mmm producer after use Jablotron Ltd hereby declares that the JA 80Y is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The original of the conformity assessment can be found at www jablotron com Technical Support section 12 MFJ55304
15. 23 Code 417 Creditunknown 608 PGYOFF _ __ _ 36 Device 324 Code 418 Credit 609 AUXON O 37 Device 325 Code 419 internal use only 610 AUXOFF _ _ _ 38 Device 326 Code 420 Error while processing command 611 CREDIT ____ 39 Device 327 Code 421 Output turnedon Numbers 01 to 50 for devices and 40 Device 328 Code 422 Output turned off codes are automatically generated by the 41 Device 329 Code 501 Instantalarm communicator so it is unnecessary to 42 Device 330 Code 502 Delayed alarm enter them in the text 43 Device 331 Code 503 Fire o e The communicator always automatically puts numbers from 01 to 50 in front of Device or Code names e Texts 0 to 532 are used to create SMS event reports e Texts 601 and 611 are SMS instructions to control the system remotely by SMS e Text 419 is for the internal use of the communicator never edit it 9260 messages are not forwarded but the communicator sends 5 6 Enabling reporting to phones them by CLIP protocol to the simulated phone line Event reports can be enabled as follows 800 all SMS and call reports disabled 801 all SMS and call reports enabled 9261 messages are forwarded to the first programmed tel number in memories M1 to M8 e g if numbers are only programmed in M5 and M6 then messages will be forwarded to M5 The tel number from w
16. 8080 TXT 20 key fob Bob 21 Key fob Jane changes the description name of the key fobs enrolled to addresses 20 and 21 8080 TXT 605 heating on 606 heating off edits the text of the two instructions used to command the heating to be switched on and off by the PGX output the PGX output must be programmed to have an ON OFF function 6 MFJ55304 Factory default SMS report and instruction texts n Factorytext n Factory text n Factory text Li Factory text al Report from your 44 Device 332 Code 504 Panicalarm _ alarm 45 Device i 333 Code C505 Invalid code entriesexceeded 1 Device 46 Device dT 334 Code CS 506 Alarmwhenpowerturnedon 2 Device 47 Device 835 Code 507 Tamperalarm _ 3 Device 48 Device 336 Code 508 Endoftamperalarm __ a Device __ 48 Device __ 87 Gode _ _808 End of alarm indication _ Device Device 338 Code 510 Alarm cancelled by user a Devise olco ss0 ods sia sete 7 Device i 202 Servicecode 340 Code id 512 Unsetting 8 Device 203 Annualinspectionrequest_ 341 Code sd 513 Partial setting 9 Device 204 Communicator 342 Code iE 514 Codelesssetting _ _ 10 Device 205 Keypad 343 Code 515 External communication fault 11 Device 206 ARC code 344 Code st 516 External comm restored 12 Device 300 Master code 345 Code TT Fett 13 Device 301
17. Ses phone calls Setting Unsetting and faults only by SMS To erase a number from memory M enter 81 M 0 Notes Entering 9 before the first digit will insert a for the international formatting of phone numbers 2 MFJ55304 if it is desired that the events be reported to the SMS phone connected to the communicator then program tel number 001 into the memory SMS report text consists of installation name event name number and name of the event source device or code date and time Example Report from your alarm setting 47 device Time 01 08 11 27 if other events or texts should be reported to a particular number change the communicator settings see 5 4 and 5 5 when storing tel numbers if you key in 7 after the last digit of the phone number the symbol is also stored and continue with one more digit 1 2 3 8 or 9 then if this tel number calls the system the system will behave as if digit had been keyed in just after the first ring i e as if it had been entered manually on the system keypad see section 3 5 Example entering 81 5 777 777 777 79 0 authorizes calls from tel number 777777777 to trigger output PGY for command will be executed The PGY output should be programmed for a 2 sec pulse function This setting is suitable for opening an electric door lock automatic gate etc 4 1 Programming The most convenient programming is best done by a PC running Comlink softwar
18. The JA 80Y GSM communicator The communicator is a component of the Jablotron Oasis 80 system This manual is valid for software version XA61010 or higher The communicator is designed to be installed within the control panel housing When connected to a GSM network it allows the following e event reporting by SMS to up to 8 telephone numbers e event reporting by phone call with an acoustic warning e event reporting to an ARC Automatic Receiving Centre also known as a Central Monitoring Station up to 2 ARCs e remote control and programming by phone remotely authorizing a phone keypad or by SMS instructions e the remote control of appliances in the house by dialling in from an authorized number free of charge with unanswered calls e remote control and programming via the Internet www GSMlink cz e connecting a phone set simulated tel line GSM gateway function incl CLIP protocol caller ID and SMS transfer e listening in and voice communication via a connected SP 02 intercom e connecting a PC to the Internet GPRS modem feature 1 Installation in the control panel If you purchased the communicator module separately it should first be installed in the Oasis control panel as follows a the control panel power must be switched off both mains and battery b Fit the communicator inside the control panel housing using screws and connect its cable to the main board c attach the adhesive GSM antenna to in
19. a lack of outgoing phone calls for a certain period cancels the validity of the SIM card then this function offers the following if there have been no outgoing phone calls within the last 90 days then the communicator automatically calls the number programmed by this sequence waits until the call is answered and then after 10 sec automatically hangs up 924 xx x 0 where xx x phone number Notes e To erase this number enter 924 0 e It is recommended to call cheap public services e g weather forecasts etc but not toll free numbers Factory default setting erased 5 17 Automatic SIM card credit interrogation The communicator is capable of checking the credit balance of its SIM card by interrogating the GSM network with an SMS containing a recognized instruction string if the network supports this feature There are two options The credit balance can be checked when the user requests it by sending an SMS instruction to the communicator or the communicator can be set to check it regularly itself To configure credit balance checking send an SMS in the format code_CREDIT_uu u_xx_yyy_zz where code valid master or service code e g 8080 or 1234 space uu u instruction recognized by the GSM network to check the balance e g 101 etc XX automatic checking period in days yyy minimum acceptable credit balance zz the textual position in which the number showing the balance starts in the reply message from the
20. actory default settings and texts erases all telephone numbers and disables reporting The text will not be changed 5 22 Memorizing the SIM card s PIN code in the communicator It is recommended to use a SIM card with disabled PIN protection If it is impossible to disable the PIN then it can still be used by entering the following sequence it must be entered after the control panel has been powered up 920 PIN 0 Example if the SIM card PIN is 1234 enter 9201234 0 Notes If the communicator does not register to the GSM network within 1 minute of the PIN being entered this problem is shown by red The JA 80Y GSM communicator LED flashes then you either entered a wrong PIN or the GSM signal is too weak In such a case o enter 920 0 while in service mode erases the entered PIN o disconnect the control panel power mains and battery o take out the SIM card and try it in a mobile phone it should register to a GSM network when located at the control panel o if you know the right PIN code and there is a GSM signal strong enough put the SIM card back into the communicator turn on the control panel power and then enter the PIN code 920 PIN 0 the communicator should then register to the GSM network its red LED should turn off within a minute The communicator memorizes the PIN and it will use it automatically whenever it registers to the GSM network If you are replacing the SIM card in the communicator with
21. asurement is repeated every second indicated by beeps This mode allows a suitable location to be found for the control panel or the GSM antenna Press the key to exit GSM signal measurement The SMS reply to a STATUS interrogation now displays GSM signal strength in the range 0 9 to 9 9 The signal should read at least 2 4 In places with a weak signal we recommended trying another GSM provider s SIM card Warning it is not recommended to use a high gain or directional GSM antenna to get a better signal as this way the communicator would only communicate with a single cellular base station and communication would not be stable Also be aware that the GSM system cannot work properly if the distance from the cellular base station is longer than 30km even if the signal is strong enough as the time delays in the data exchange would be longer than acceptable to the GSM standard 5 3 Programming tel numbers for reporting to phones See part 4 5 4 Selection of the events reported to phones The factory default list of reported events and their assignment to telephone numbers M1 to M8 can be altered by this sequence The complete list of reportable events is shown in the following table It is possible to select whether the event should be reported by an SMS or by a phone call or by both an SMS followed by a phone call Each event has pre programmed factory default SMS text These texts can be edited see 5 5 The acoustic signals
22. can add or remove other installations to or from his her GSMLink account e there is a demo version of remote access on www GSMLink cz e using www GSMLink cz is free of charge 7 6 A complete list of CID reports to ARCs A report to an ARC consists of installation ID event code subsystem number and the number of the source device or code In IP CID and SMS CID in addition to this a time stamp is also sent as follows List of the CID reports CID code Event ec 1130 3130 Intruder alarm instant restored 1 9 1134 3134 Intruder alarm delayed restored 2 9 1110 3110 Fire alarm restored 3 9 1120 3120 Panic alarm restored 4 9 1461 3461 Number of incorrect code entries exceeded 5 9 alarm restored 1140 3140 Alarm triggered during control panel power up 6 9 restored 1137 3137 Tamper alarm no tampering 7 8 1144 3144 Device tamper alarm no tampering 7 8 1406 Alarm cancelled by user 10 1401 3401 Unsetting setting 12 11 3402 Partial setting 13 3408 Codeless complete setting 14 1354 3354 External communication fault restored 15 16 1300 3300 Fault except device all faults restored 17 18 1330 3330 Device fault all faults restored 17 18 1301 3301 Mains dropout longer than 30 minutes 19 20 21 restored 1302 3302 Battery fault except devices all battery faults 22 23 restored 1384 3384 Devi
23. ce battery fault all battery faults restored 22 23 1306 3306 Switching to Service Mode Leaving Service 24 25 mode 1661 3661 PGX ON OFF 26 1662 3662 PGY ON OFF 27 1355 Radio communication jamming present 28 1350 3350 Internal communication fault restored 29 30 1602 Communication test 31 1138 Unconfirmed alarm 32 1351 Communication fault to ARC1 to ARC2 if backups 1393 Annual check request 17 1551 3551 Communicator blocked restored 31 only in IP CID List of source numbers Source Source number 701 Control panel 731 Communicator 741 Wired keypad 001 050 Devices 01 50 500 Master code 599 Service code 501 550 Codes 01 50 Subsystem 01 in all reports In a split system for setting and unsetting 02 A 03 B For partial setting 02 A 03 AB The JA 80Y GSM communicator 8 Technical specifications Power 12V DC from the control panel Stand by consumption about 35 mA depends on the GSM signal Max consumption during communication 1A GSM band E GSM GPRS 900 1800MHz RF output power 2 W for GSM900 1 W for GSM1800 AUX output dry NC contact max 60 VDC 100 mA Complies with EN 50131 1 EN 50136 2 1 as ATS4 ATS 5 if CID protocol is used and the repeating period is set to zero Sequence 06a0 Security grade 2 Operating environment 10 to 40 C class Il Safety EN 60950 1 EMC ETSI EN 3
24. ction see 5 17 7 Alarms by phone call if you answer the call you hear a Example by sending code SET valid code space SET the system will set if it is already set it will not change its status Notes performance of the instruction is confirmed by an SMS reply the instruction texts are not case sensitive and only ASCII characters are allowed only one instruction can be in an instruction SMS a setting unsetting instruction starting with the service code will only be performed if setting unsetting with the service code is enabled in the control panel to protect against unauthorized setting unsetting by installers an SMS instruction can also be sent to the alarm system from a phone connected to the communicator if supports SMS to phone number 001 for free if there is any other text in the instruction not separated by the instruction will not be performed if you are sending an instruction and you are not sure whether any other text will be automatically added to the SMS for example when The JA 80Y GSM communicator siren sound 8 Technical fault by SMS suitable for an installer To program phone numbers to the M memories enter the following sequence while in Service mode 81 M xxx x 0 where M is memory 1 to 8 XXX X iS a phone number max 20 digits Example entering 81 5 777 777 777 0 will store the number 777777777 in memory M5 Alarms will be reported by SM
25. e locking code It will then relock on exiting service mode e The ARC settings can be permanently unlocked by entering 901 0 while ARC programming is temporally enabled see above This will erase the locking code Factory default setting ARC settings unlocked 5 35 Engineer reset supported Starting from this version the communicator firmware supports the Engineer reset feature also requires the control panel firmware to be of version KE60108 or higher This feature is designed for ARC Alarm Receiving Centre connection to satisfy the following requirements of the DD243 standard After a confirmed alarm has been triggered the control panel must switch to a disabled state Switching to normal operation is then only possible using a valid ARC access code Until then the system remains completely disabled no operation or programming is possible even when in Maintenance or Service mode An ARC access code can be entered in the following ways GSMlink in the field used for remote code entry SMS instruction ARC code_instruction e g 12345678 STATUS 6 GPRS modem feature The communicator can be used as a GPRS modem to connect a PC to the Internet A suitable cable is provided with the communicator The cable should connect a PC s serial COM port to thae data connector on the communicator board the cable length must not be extended It is also necessary to install the driver in the PC which is found on the CD ROM
26. e or via the Internet and website www GSMLink cz or by programming SMS PRG sequence Programming is also possible via the system keypad The control panel must be in Service mode if it is not enter O Service code factory default 8080 while the system is unset Enter the relevant programming sequences see the following description To exit service mode press the key 2 seconds after the first ringing signal from this number the 9 5 Programming sequences xx 01 to 17 where 01 EN 02 CZ 03 SK 04 NL 05 DE 06 PL 07 Enalish DA 08 IT 09 PT 10 FI 11 NO 12 SV g 13 FR 14 HU 15 RU 16 TR 17 SP On keypad or in ComLink software range 0 4 to 4 4 In reply to STATUS SMS range 0 9 to 9 9 exit by pressing M memory 1 to 8 XxX X tel number max 20 digits keying in 9 and 7 81 M 0 erases the number in memory M Language setting GSM signal strength measurement Tel number programming for reporting to telephones 81 M xx x 0 all M1 to M8 erased Selection of events to report by SMS 82 Mec x M1 amp 2 alarms by SMS M3 amp 4 alarms by SMS and call M5 amp 6 alarms by SMS and call Set Unset by SMS M7 alarms by call MB technical faults by SMS to installer M tel number memory from 1 to 8 ec event code see 5 4 Selection of events to report by x 1 report x 0 no report phone call SMS text editing Texts can be edited by Comlink software or by SMS instruction 9 code TXT
27. for phone call reporting are fixed and cannot be changed e g an alarm is indicated by a siren sound if a reporting call is answered List of events which can be reported to phones and their factory default assignment to particular phone numbers i N 01 Intruder alarm instant 02_ Intruder alarm delayed 03 Fire alarm Panic alarm Number of permitted incorrect code entries exceeded Alarm triggered during control panel power up Nn o op Tee Tee ep Tamper alarm nn n op Tee Tee ep End of tamper alarm End of alarm indication Alarm cancelled by user Setting Unsetting Partial setting Codeless setting External communication fault External communication restored Fault Fault no longer present Mains dropout longer than 30 minutes n n ANIN n n Cp Tee Tee ep Kee ep Mains dropout Mains restored Discharged battery Battery OK Switching to Service Mode Leaving Service Mode PGX ON OFF PGY ON OFF Radio communication jamming present Internal communication fault Internal communication restored Communication test Unconfirmed alarm e Factory default report assignment S SMS C call SC SMS followed by a call e External communication fault means a GSM network dropout longer than 15 minutes if GSM network dropout indication is enabled e The SMS information abou
28. ful the next attempts occur after the programmed repeat period see 5 28 If an alarm is cancelled by a user while it is being reported any unsent SMSes and unperformed call reports are cancelled but the ARC still gets a complete set of reports about events in the system 7 2 The communicator s LED The red LED on the communicator board indicates as follows e regular flashing not registered to a GSM network e lit permanently communication in progress registration to a GSM network an SMS transfer or a phone call e 3 flashes pause 3 flashes GPRS modem mode 7 3 After entering service mode the communicator e finishes reporting to ARCs if any is needed and confirms successful data transmission by a short ring from the phone connected to the simulated tel line e unfinished SMS and call reports are cancelled e unsent ARC reports are only erased if ARC tel numbers IP addresses or the ARC communication format or the installation ID are changed e alarm restoration reports or fault restoration reports are sent to the ARC even in service mode e changes to communicator settings do not take effect until service mode has been exited 7 4 Configuring the communicator in maintenance mode If configuring the communicator in maintenance mode is enabled via control panel programming then the above described programming sequences can be used to set e tel numbers M1 to M7 e the events reported by SMS and
29. hich the SMS 802 all reports enabled except reports of setting and unsetting by users 41 to 50 i e their codes cards and key fobs This allows setting and unsetting done by report recipients owners bosses etc not to be reported Factory default setting 801 all reports enabled 5 7 Remote access Remote access by phone or Internet can be enabled or disabled 9030 disabled 9031 enabled Factory default setting enabled 5 8 Forwarding of incoming SMS messages This feature enables the automatic forwarding of incoming SMS messages which contain no valid instructions to the system The JA 80Y GSM communicator was received will be shown at the beginning of the forwarded text Factory default setting messages are forwarded 5 9 SMS instruction confirmation If the communicator receives a valid SMS instruction the instruction sender will be made aware of its successful execution by the reception of a conformation SMS sent by the communicator This confirmation can be disabled as follows 9270 disabled 9271 enabled Factory default setting enabled 5 10 Reaction to incoming calls The communicator s reaction to incoming phone calls can be set by 904 x 7 MFJ55304 where x 0 incoming calls are ignored x 1to8 the communicator will answer after x multiplied by 5 seconds of ringing e g x 4 20sec x 9 answers after a second call first there must be at least one ring then a pause 10 to 45sec and
30. k If the red LED starts flashing after awhile switch off the control panel power put the SIM card into a mobile phone and check that it registers to the network in place of the control panel and without any PIN code requests d close the control panel cover the alarm system should be in Service mode if it is not enter 0 Service code factory default 8080 with the alarm system unset disarmed e key in 98101 to set texts of the communicator to English language f key in 922 to measure the GSM signal strength should indicate in the range 0 4 to 4 4 It should be at least 2 4 for reliable functioning If the signal is weak change the location of the control panel or try a SIM card from another GSM provider it is not recommended to use either a high gain or directional antenna see 5 2 g if the GSM signal is sufficient test the communicator functions for example calling the system s SIM card number and authorizing the phone keypad you are using see 3 3 If installed at a location near a national border where roaming to a foreign network is highly likely e g when the signal strength is fluctuating we recommended blocking the roaming feature in the SIM card to avoid unnecessarily high communication fees Contact your GSM provider for details 3 User functions of the communicator The following text describes all communicator features The installer should show the end user how to operate the functions used in a
31. m ID for ARC use 03 a zz z 0 Selecting the ARC protocol 04ax Selection of events to report to ARCs Defining the delay before data is resent to an ARC ARC communication checking period The time to wait after the last report 07 a hhmm before performing an ARC communication check Enable ARC reporting ARC2 backs up ARC1 Recording reports sent to ARCs in the control panel memory Indicate an ARC communication fault if a report is not successfully received by an ARC within 110 sec of transmission IP address for data transmission 013 xx x 0 901 xx x 0 Locking the ARC settings Unlocking the ARC settings 900 xx x 0 programming sequence set also from the keypad e g 8080 PRG 08080 201 set the 10s exit delay The communicator will unregister from the GSM network and then re register Also possible via the SMS instruction code GSM Code master user or service code Resets to the factory default settings and erases all phone numbers text will not be changed xx X new PIN sequence 920 0 erases the PIN to use a SIM card with a disabled PIN erased by SMS instruction to the alarm system code GPRS x x y y Z 2 where code master or service code x x the APN y y name z z password only enter the APN if the name and password are not required by the GSM provider a 1 ARC1 a 2 ARC2 xx x tel number max 20 digits or IP address amp port for example 01 2 8 192
32. n text n text or by www GSMLink cz via Internet x 0 disabled x 1 enabled all programmed by 82 amp 83 x 2 enabled without reporting setting unsetting by users 41 to 50 codes cards amp key fobs and master code setting unsetting x 0 disabled x 1 enabled by phone and Internet x 0 no x 1 yes if the incoming text is not an SMS instruction it will be forwarded to the first programmed number in memories M1 to M8 83 Mec x Enable reporting to phones Remote access Forwarding of incoming SMSes SMS instruction confirmation Reaction to incoming calls x 0 no x 1 yes by SMS reply x 0 no reaction x 1 to 8 answers after 1 to 8 rings x 9 answers after the 2 call x 0 tel line GSM gateway x 1 alarm system keypad x 2 off x 3 automatically calls an emergency tel number when the tel receiver is picked up answers after 5 rings 25s tel line Xx X tel number max 20 digits x 0 no x 1 yes 15min dropout Fault no 5 Phone speaker loudness a a Number to be periodically called _ _ to maintain SIM card validity 924 xx x 0 XX X tel number max 20 digits 924 0 erase Via an SMS instruction to the alarm system code CREDIT uu u xx yyy zz where code master or service code uu u GSM network command string to ascertain the credit e g 104 xx auto interrogation frequency in days yyy minimum acceptable balance zz the textual position at which the number showing the balance s
33. nset and switched to the service mode e The number of sequences in one SMS is limited by the maximum size of the SMS in the GSM network Example by sending SMS 8080 PRG 08080 201 the exit delay will be set to 10s 5 19 Registration code for www GSMLink cz If remote access via the Internet is desired then the system has to be registered on the web page www GSMLink cz Each communicator has its own unique registration code which is printed on the label attached to the communicator module This code can also be sent by SMS to your mobile phone by the keypad entry 910 xx x 0 where xx x is the tel number to send the code to Notes e It takes a certain time to receive the registration code depends on the current traffic in the network e The registration code has the format XXXXX XXXXX XXXX 5 20 Triggering re registration to the GSM network After 923 has been entered the communicator quits the GSM network and then re registers itself This re registration does not change any settings in the communicator It should be used after GSM network faults or data collisions and in some networks it also has to be used after a blocked SIM card has been unblocked by the GSM provider It is also possible if the SIM card can still receive to trigger GSM network re registration by sending the SMS instruction code GSM code master user or service code 5 21 Communicator reset Entering 98080 returns the communicator to its f
34. or 5 5 SMS text editing The communicator contains various text strings which are used to create SMS reports and also SMS instruction text Language of the text can be set see 5 1 These text strings cannot be changed from the system keypad but they can be edited by Comlink software via the Internet www GSMLink cz or by sending the following SMS instruction code_TXT_n text n text n text where code is a valid access code e g factory defaults 8080 1234 is a space TXT instruction to edit texts n text number 0 to 611 see the following table 3 comma or full stop text the new text max 30 characters which will replace the former text It is invalid to enter a comma or a full stop inside the text string but a space is valid within the text string Notes e A single TXT instruction can change multiple texts limited only by the maximum length of a single SMS e the communicator is not case sensitive and it is recommended to use only English ASCII characters some networks do not support non English national characters e the communicator creates SMS reports with 5 parts installation name event description source code or device number 01 to 50 source name time and date e the maximum possible length of an ASCII SMS is 160 characters only 70 characters for national characters If this length is exceeded the report is sent as multiple SMSes Examples if the service code is 8080 then the SMS instruction
35. ossible to deliver it to ARC1 A report containing Communication fault to ARC1 is then sent to ARC2 together with the first report to ARC2 Factory default setting both ARCs off 5 31 Recording reports sent to ARCs in the control panel memory This sequence enables the recording of every report successfully communicated to ARCs in the control panel s internal memory 080 enabled 081 disabled Note it is recommended not to record reports sent to ARCs but to enable the indication of ARC communication faults see 5 32 This saves a significant amount of control panel memory The system initially assumes that every report is successfully delivered to ARCs but if a report is not successfully delivered within 110 seconds of transmission then a communication fault will be indicated and recorded Factory default setting enabled 5 32 Indicate an ARC communication fault if a report is not successfully received within 110 sec of transmission Enables the indication and recording of a communication fault if a report is not successfully delivered to an ARC within 110 seconds of its transmission 090 communication faults not indicated 091 communication faults indicated Notes e The communicator continues trying to send information to an ARC even after a communication fault has been indicated after the data has been delivered communication fault indication stops e For communication checking reports the delivery time limi
36. particular installation 3 1 Making a phone call from a connected phone The communicator provides a simulated phone line including CLIP protocol to connect a phone set e the phone tone dialling only should be connected to the telephone socket on the communicator board or to the PHONE terminals e the phone can be used as if connected to a standard telephone line factory default settings of the communicator e if the phone supporting SMS messages is used then besides phone calls it is also possible to send and receive SMS messages see 5 11 1 e the communicator terminates current phone calls if it is due to send event reports e some phone sets are sensitive to nearby GSM radio signals If you hear strong interference in the phone receiver caused by the communicator s GSM signal change the location of the phone set 3 2 _Listening in and voice communication If listening in and voice communication are needed then an SP 02 intercom should be connected to the phone line simulated by the communicator The intercom can be connected in parallel to any existing phone set The SP 02 works as a speaker phone which answers calls automatically when coming from telephone numbers authorized to access the listening in feature The SP 02 also provides a push to talk feature to call a number stored in its memory See the SP 02 manual for details on how to authorize numbers to listen in and how to program the push to talk number 3 3
37. programmed to report to phone number 001 the reports will be sent to the attached phone via the simulated line free of charge If the attached phone provides caller identification CLIP then the caller s phone number will be shown on the display 5 12 Emergency telephone number If the simulated phone line is set to emergency call mode see 5 11 then after picking up the receiver the phone will automatically call a number programmed by 952 xx x 0 where XXX X is a phone number max 20 digits keying in 9 will enter for international calls To erase the number enter 952 0 Factory default setting the emergency number is erased 5 13 GSM signal dropout indication This selectable feature monitors connectivity with the GSM network If enabled it indicates problems and generates an_ external communication fault report if there is a GSM signal dropout longer than 15 minutes 9210 disabled 9211 enabled Factory default setting disabled 5 14 The microphone sensitivity of the phone The sensitivity of the attached phone or intercom can be adjusted by The JA 80Y GSM communicator 953x where x can be from 1 to 9 max factory default 5 5 15 The speaker loudness of the phone The loudness of the attached phone intercom can be adjusted by 954x where x can be from 1 to 9 max factory default 5 5 16 Number to be called to maintain SIM card validity If a prepaid SIM card is used and
38. side the control panel s plastic housing on the lower internal wall and connect the antenna to the communicator never switch the control panel power on if the GSM antenna is not connected to the GSM module as this will cause serious damage d connect the relevant cables to the communicator if you intend using the simulated telephone line the AUX output or a PC serial data cable for the GPRS modem function SMS phone connected to RJ socket or PHONE terminals AUX relay terminals GSM antenna Internet connection via COM port Fig 1 Communicator wiring The JA 80Y GSM communicator 2 Powering up the communicator for the first time If the communicator is installed in the control panel and its GSM antenna is connected then a have a suitable SIM card ready It should be activated see if it works in a mobile phone first If it requires a PIN code when turning the phone on then disable the PIN code request for example in Nokia via Menu Settings Security settings PIN code request Off The communicator can work with a prepaid card but for more reliable functioning use a tariff card see 5 16 b insert the SIM card into the communicator to open the card holder push its frame up a little c switch on the control panel power mains and battery The communicator s red LED should go off within a minute successful registration to the GSM networ
39. simulated line It is only necessary to pick up its receiver and briefly press the key Then the phone is ready to work as a control panel keypad To finish operating just hang up Phone keypads have to be re authorized each time the system is called by entering the codes specified earlier as phone keypads are only authorized as system keypads for the duration of a call to the system 3 4 SMS instructions to control the system remotely All incoming SMSes are checked by the communicator and if there are any instructions to the system they will be performed Each instruction message must have the following format code _ instruction valid code space instruction Valid code any valid code in the system e g 8080 1234 etc The factory default instruction texts editable see 5 5 using an SMS internet gate type the instruction as code instruction 3 5 Toll free remote control by unanswered calls from pre authorized phones A limited number of system functions can be activated remotely by calling the system from pre authorized phones and terminating calls before the system answers This way limited control of the system is free of call charges It is possible to pre authorize phone numbers stored in memories M1 to M8 also used for event reporting see 4 To pre authorize a telephone number store at the end of the number and follow it by a single digit 1 2 3 8 or 9 see the notes in section 4
40. t confirmation from the ARC is 300 minutes But if any other report is sent to the ARC it must be confirmed within 110 seconds otherwise a communication fault will be indicated Factory default setting communication faults not indicated 10 MFJ55304 5 33 IP address for data transmission The communicator supports transmission of special data e g visual information from the system to the set IP address which can be set by the following sequence 013 8 xxx XXX XXX XXX yyyyy 0 where concerning 8 insert these characters to identify the following IP address which must consist of 12 digits followed by 5 digits for the port see below xx X is the12 digit IP address y y is 5 digits for the port see manual of the communicator Example 013 8 195 039 077 154 07070 0 To erase the IP set 013 0 Note if no devices supporting this feature are in the system do not set the IP address Factory default 77 104 220 129 7070 img jablotron com 5 34 Locking the ARC settings All settings which effect reporting to ARCs can be locked by a digital code 901 xx x 0 where xx x is an installer defined locking code 4 to 8 digits Notes e Exiting service mode after the locking code has been entered will lock all the settings effecting ARC communication see the sequence list in section 5 e If ARC programming is locked then it can be temporally enabled in service mode by entering 901 xx x 0 where xx x is th
41. t a new picture on the server is sent to all phone numbers which are set to get reported event number 01 Intruder alarm The JA 80Y GSM communicator instant This information contains a link to the new picture on the server MFJ55304 5 4 1 Assigning events to be reported by SMS to a particular mobile phone number To link events to being reported by SMS enter 82 Mec x where M phone number memory 1 to 8 ec event code 01 to 32 see the above table x 0 no SMS report 1 SMS report Example if 82 8 03 1 is programmed and a fire alarm is triggered event 03 in the table it will be reported by SMS to the phone number stored in memory M8 5 4 2 Assigning events to be reported by phone call to a particular phone number To link events to being reported by phone call enter 83 M ec x where M phone number memory 1 to 8 ec event code 01 to 32 see the above table x 0 no phone call 1 call Example if 82 1 03 1 is programmed and a fire alarm is triggered event 03 in the table the phone number stored in memory M1 will be called and if the call is answered a siren sound will be heard Notes Phone call reports are mostly used as an audible notification to alert the user of a detailed report sent by SMS If both SMS call reports are enabled for events the SMS is sent first and then the number is called afterwards But total priority is given to ARC reports if enabled see 7 1 The JA 80Y GSM communicat
42. tarts in the reply message from the GSM provider If the credit is lower than the minimum the provider s SMS will be auto forwarded to numbers M1 and M8 for someone to top up the pre paid SIM card Simulated phone line function Emergency tel number GSM signal dropout indication Phone microphone sensitivity x 1 to 9 9 maximum Using an SMS instruction to configure automatic SIM card credit interrogation Getting your www GSMLink cz registration code sent to your mobile phone 910 xx x 0 Xx X your mobile phone number The JA 80Y GSM communicator 3 MFJ55304 Credit balance checking is set by SMS instruction code_CREDIT_uu u_xx_yyy_zz where uu u Automatic SIM card credit interrogation instruction for the GSM network e g 101 etc xx period in days yyy minimum balance zz the position in which the number showing the balance starts If the reported credit balance is lower than the set limit yyy the credit balance message from the provider will be forwarded to phone numbers M1 and M8 System can be programmed remotely via SMS instruction code PRG seq seq where seq is Programming by SMS Triggering re registration to the GSM network Communicator reset Memorizing the SIM card s PIN code in the communicator 920 xx x 0 Configuring the GPRS log in parameters ARC main tel number IP address 01 ae x0 ARC backup tel number IP address 02 a xx x 0 Installation alarm syste
43. then just after the first ring of the second call the call will be answered Factory default setting 9045 answers after 25sec about 5 rings 5 11 The simulated phone line function This sequence defines the function of the phone connected to the simulated telephone line if used 98 y phone line for making phone calls If the key is pressed when the receiver is picked up the phone will work as an alarm system keypad the phone works as a system keypad it is impossible to make phone calls emergency call automatically calls a pre programmed number see 5 12 just after the receiver is picked up Pressing the key within 2 sec after having picked up the receiver will switch to a dial tone and will allow the user to make phone calls Note while the communicator is occupied with reporting events or it is not registered to the GSM network a busy signal is heard on the connected phone Factory default setting y 0 phone line 5 11 1 Using an SMS phone connected to the simulated line A phone capable of sending and receiving SMS messages by CLIP protocol can be connected to the simulated phone line In the phone both the TX and RX numbers should be programmed to 1111 If an SMS message is sent from this phone to the phone number 001 it will go directly to the communicator free of charge This can be used to send instructions to the system e g text programming etc If the communicator is
44. x x 0 Backup 02 a xx x 0 where a 1 ARC1 2 ARC2 XXx X tel number max 20 digits or IP address and port entry format example 01 2 8 192 168 001 123 08080 0 where 8 auto converts to signifies an IP address which must have 12 digits and must be followed by the 5 digits of the port number no separators To erase a tel number IP address enter 01p 0 or 02p 0 If numbers IP addresses are erased there will be no reporting to that particular ARC Note the communicator first tries to send data to the main number address if it is not successful it tries the backup Factory default setting all tel numbers IP addresses erased 5 25 Installation alarm system ID for ARC use The installation s ID number which is sent to an ARC with every report can be programmed with 03 a zz z 0 where a 1 ARC1 2 ARC2 9 MFJ55304 zz z installation ID number max 8 characters 0 to 9 and 1 A to 6 F hexadecimal number Factory default setting 0000 for both ARCs 5 26 Selecting the ARC communication protocol To select the required communication protocol enter 04ax where a 1 ARC1 2 ARC2 x 0 Contact ID 1 SMS CID 2 IP CID Notes e IP CID is the fastest of the above protocols and it also allows very frequent checking of communication reliability with the ARC e g every 5 minutes e Contact ID protocol can be used with ARCs linked by standard telephone lines if they support Contact ID
Download Pdf Manuals
Related Search