User Manual
Contents
1. Sh Mini Pix 4 Batten 4 x 9W tri colour COB LEDs User Manual Order code LEDJ262 Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCK IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or informative labels from the unit If the equipment has been exposed to drastic Do not open the equipmen2. 1 120 127 Colour 7 Active when Flash 0 255 Slow to fast CH1 value is ia Speed 0 255 Slow to fast Active when CH1 value is 136 255 www prolight co uk Mini Pix 4 Batten User Manual 4 led Operating instructions 6 channel mode CH3 Master dimmer Active when CH1 value is 0 135 96 103 Colour 4 PERC rozsa i025 Speed 0 255 eo on value is 136 239 Sensitivity 0 255 240 255 SOUND Active when CH1 sound value is 240 255 12 channel mode R1 G1 B1 R2 G2 B2 R3 G3 B3 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 cH1o cHat chaz R4 G4 B4 R5 G5 B5 0 255 0 255 0 255 0 255 0 255 0 255 www prolight co uk Mini Pix 4 Batten User Manual 5 ledi Operating instructions 15 channel mode CH3 16 23 R 24 31 G 32 39 B 40 47 RG 48 55 GB 56 63 RB 64 71 RGB Master dimmer Active when CH1 UREA value is 0 135 0 15 BLACKOUT 1 TROED aan c02s8 Speed 0 255 oao value is 136 239 Sensitivity 0 255 240 255 SOUND Active when CH1 sound value is 240 255 www prolight co uk Mini Pix 4 Batten User Manual 6 amp 6 Operating instructions Master slave mode To set the master unit press the MODE button on the rear of the master unit then select your desired program sound active auto static colour or one of the built in programs To set the other units in slave mode press the MODE button on the rear
3. In this mode it will run 14 built in programs in a continuous loop Built in programs mode To access the built in programs mode press the MODE button on the rear of the unit to show 01 STATIC on the LED display Now press the ENTER button and use the UP and DOWN buttons to select between the 14 built in programs Now press the ENTER button to select the desired speed and adjust by using the and DOWN buttons Speed values 01 99 00 slow 99 fast Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button See next page for built in programs chart www prolight co uk Mini Pix 4 Batten User Manual 7 Operating instructions 02 DREAM Speed 00 99 Flash 00 99 03 METEOR Speed 00 99 Flash 00 99 FLOW 1 Speed 00 99 Flash 00 99 07 FLOW 2 Speed 00 99 Flash 00 99 FLOW 3 Speed 00 99 Flash 00 99 FLOW 4 Speed 00 99 Flash 00 99 r Invert mode To access the invert mode press the MODE button on the rear of the unit to show INVERT ON OFF on the LCD screen Press the ENTER button and use the UP and DOWN buttons to turn the this mode on and off OFF Left to Right flow ON Right to Left flow In this mode via the ON OFF options you can adjust the effect direction from left to right or from right to left Press the ENTER button to confirm the setting To
4. N C Pin 5 N C 3 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen 9 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Mini Pix 4 Batten User Manual 10 WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries Si with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CE www prolight co uk Mini Pix 4 Batten User Manual 11 www prolight co uk Mini Pix 4 User Manual 12
5. code LEDJ262 25 Lux 1643 438 202 116 75 _ u NA o SAN MEN NN C Na a Om 1m 2m 3m 4m 5m Gp Mini Pix 4 www prolight co uk 01 Bracket 02 Bracket tightening knobs 03 Earth point 04 Safety eye 05 LED display 06 Function buttons 07 DMX input socket 08 DMX output socket www prolight co uk 09 IEC power in socket 10 IEC power out socket 11 Fuse 1A 250V 2A 125V 12 Yoke floor stand In the box 1 x fixture 1 x power cable amp 1 x user manual Mini Pix 4 Batten User Manual 3 Operating instructions DMX channel mode Operating in DMX control mode gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX channel mode press the MODE button on the rear of the unit to show DMX MODE on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the desired DMX address Now press the ENTER button to choose one of the 3 4 6 12 or 15 DMX channel modes use the UP and DOWN buttons and press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button 3 channel mode 4 channel mode H3 96 103 Colour 4 Master dimmer
6. of the unit to show SLAVE MODE on the LED display and press the ENTER button to confirm the setting The unit will now run in sequence with the master unit To exit out of any of the above options press the MODE button Please ensure that all slave units are set to the same DMX channel mode as the master unit Sound active mode To access the sound active mode press the MODE button on the rear of the unit to show SOUND MODE on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the sound sensitivity level and press the ENTER button to confirm the setting SENS 00 31 00 low 31 high Now press the ENTER button and use the UP and DOWN buttons to set the frequency level and press the ENTER button to confirm the setting FQN 01 99 01 low 99 high To exit out of any of the above options press the MODE button Auto run mode To access the auto run mode press the MODE button to show AUTO RUN on the rear of the unit Now press the ENTER button and use the UP and DOWN buttons to set the frequency level and press the ENTER button to confirm the setting FQN 01 99 01 low 99 high The frequency level adjusts how many times the program repeats before moving to the next program To exit out of any of the above options press the MODE button Note
7. 9 DMX setup Notice Be sure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR EN ne OM eni XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interferance it is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal _ resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order ref CABL9O 5 pin Order ref CABL89 S pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A E 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4
8. exit out of any of the above options press the MODE button Dimming curve To access the dimming curve mode press the MODE button on the rear of the unit to show DIMMER CURVE on the LCD display Now press the ENTER button and use the UP and DOWN buttons to select between the 2 dimming curves 01 Halogen emulation mode with a very smooth slow dimming and a small delay 02 LED response with faster dimming and no delay Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button www prolight co uk Mini Pix 4 Batten User Manual 8 DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travel
9. orrect operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Mini Pix 4 Batten User Manual 2 Product overview amp technical specifications Mini Pix 4 Batten The Mini Pix 4 batten offers full pixel mapping technology within a compact rugged chassis allowing lighting designers and DJs to create stunning on stage eye candy type effects QW COB chip on board tri colour LEDs deliver a full spectrum of colours chases and patterns accessible from a large number of internal programs The Mini Pix 4 batten also has a number of built in DMX personalities to simplify integration and compatibility with variety of DMX consoles e 4x QW tri colour COB LEDs e Beam angle 25 e DMX channels 3 4 6 12 or 15 selectable e Static colour colour mix colour change colour fade built in programs auto sound active and master slave modes e Remote device management RDM e Bracket allows for multiple rigging or floor standing applications e 4 push button menu with LED display e 3 Pin XLR in out sockets e IEC power in out sockets e Fan cooled 140mm Q Q Q Q Specifications Power consumption Mini Pix 4 Batten 48W Power supply 100 240V 50 60Hz Fuse 1A 250V 2A 125V Dimensions 340 x 148 x 140mm Weight 2 8kg Order
10. s from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Also remember that DMX cable must be daisy chained and cannot be split www prolight co uk Mini Pix 4 Batten User Manual
11. t and do not modify the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use e Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or WARRANTY One year from date of purchase damaged Check the equipment and the power cable periodically Only use fuses of same type and rating OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Inc
Download Pdf Manuals
Related Search