Home

User Manual

image

Contents

1. OBLAMATIK USER MANUAL SMARTLEVEL for washbasin in public and bi stable solenoid valve Ow Disclaimer This manual was created with great care Oblamatik AG shall not be liable for technical or typographical errors and reserves the right to make changes to the product and or the instructions at any time without notice Oblamatik is not liable or responsible for direct or indirect damages which is in connection with the installation or operation of this product Imprint This manual is a publication of Oblamatik AG Gaeuggelistrasse 7 CH 7000 Chur SWITZERLAND All rights including translation are reserved Reproduction by any method for example photocopies or electronic recording are not allowed Reproduction in full or partly is prohibited These instructions represent the technical status at time of printing 6 The user manual must be given to the user Please read this user manual carefully before using the system and keep in a safe place for future reference To reduce the risk of injuries scalding and electrical shock the safety precautions below must be instal led and followed Risk of injury This device is not intended for use by persons with different or reduced physical sensory or mental abi lities or who lack experience or knowledge unless they are under the supervision of or receive training for the use of the device by a person responsible for their safety CONTINUOUSLY TURNING
2. THE CONTROL WHEEL IN THE CLOCKWISE DIRECTION MAY OVERRIDE THE PRE SET MAXIMUM TEMPERATURE RESULTING IN A RISK OF SCALDING If the power cord gets damaged it must be replaced by the manufacturer its authorized service agent or qualified personnel to avoid danger Never operate the device with a damaged cable or plug Do not pull on the power cable as this could cause damage to the cable and cause electric shock Malfunctions Possible cause Solution The device is not working Start Diagnostic Check that The control unit is connected to the mains There is no power supply failure The electric plug inside the control unit is well connected No water flow when activated Check that Your faucet is connected to the water supply Both angle valves are fully opened Check another faucet in the house if water is running The water supply hoses are not bent or twisted The supply hoses might be soiled The control unit is connected to the mains Minimal water flow Check that Both angle valves are fully opened The water supply hoses are not bent or twisted The supply hoses might be soiled Continuous water flow Press the ON OFF button Close angle valve or main valve After a few minutes open again It s still a continuous water flow close valve and contact your installer Use soft cloth soapy solution and water for regular care Wipe with a dry cloth Avoid the use of abrasives or solvents which damage the surface Dam
3. age caused by inappropriate treatment by the user is not covered by our guarantee for washbasin application for public and bi stable solenoid valve w The following settings are active for 5 min after initiation Maximal water flow time Press amp hold for 2 sec until LED color ring is flashing RED Release knob immediately Basic functions via menu button Water ON Press 1x water ON Water OFF Press amp hold for 2 sec and adjust desired Press 1x water OFF water flow time Changing between the water flow time Activating the cleaning mode Press 1x briefly Deactivate Interface disabling of water flow for 45 sec Saving the settings Press amp hold until LED color ring is flashing GREEN Release knob immediately AE E OURO flashing 2x in the selected color Reactivate Interface Flashing color Water flow time Press amp hold until LED color ring GREEN goes out or wait 45 sec automatic reactivation Color setting of the LED color ring Press amp hold for 2 sec until LED color ring is flashing RED Release knob immediately Press 2x briefly until LED color ring is flashing GREEN Release knob immediately BLUE 1 min Press amp hold for 2 sec choose desired color Changing between the colors WHITE close Press 1x briefly Hygienic flushing Saving the settings Press amp hold for 2 sec until LED color ring is flashing RED Release knob immed
4. iately Press amp hold for 2 sec until LED color ring is flashing 2x in the selected color Press 1x briefly until LED color ring is flashing YELLOW Release knob immediately apiece ane Press amp hold for 2 sec and adjust desired interval flushing BLUE Changing between the interval flushing Press 1x briefly BLACK inactive Saving the settings Press amp hold for 2 sec until LED color ring is WHITE close flashing 2x in the selected color Is operating with a connected bi stable solenoid valve Flashing color Interval 1 day 10 sec 2 days 10 sec 3 days 10 sec WHITE close de de x de VY lt Py yno REISE pjoy suna POON dn samod Jaye sdynuiw G 15 11 1 dnyas 995 Gt PEM JO 995 Z 104 pyoy y2N0 jnosu 9109 95 de plou 9 yono 99 2 asn 18 0 950 2 i de e u ew de 950 2 de 9950 sAepe de 29s OL sAep Z de 39501 Aep LL de 950 2 de de 950 2 de bunjas 10102 de Oblamatik AG Gauggelistrasse 7 CH 7000 Chur 28207000 infoBDoblamatik ch oblamatik ch 222709 O 09 15

Download Pdf Manuals

image

Related Search

Related Contents

1 of 37 CUDAfy User Manual 0.3 Project CUDAfy Title CUDAfy User  HOW TO PAINT A ROOM - Graco Magnum Paint Sprayers  CR6003A - Golden Oldies Outlet  User Manual AIMB-225  DSD G/L Editor User Manual  Sony XBR49X850B Flat Panel Television User Manual  miline FTL10 - microSYST Systemelectronic  こちら  YL— 7 Series Intelligent Temperature Controller (ITC) ITC User Guide    

Copyright © All rights reserved.
Failed to retrieve file