view/download manual - Jumpking Trampolines
Contents
1. Frame Completion You have now completed the 4 individual segments of the OvalPOD frame You will have the following 2 x Assembly 1 each comprising top rails B A and C with W leg 2 x Assembly 2 each comprising top rails B A E and D with W leg Assembly 2 top rails B A E and D Assembly 1 top rails B A and C Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines The following steps will require a minimum of two people and we recommend you wear gloves Now turn over 1 x Assembly 1 and 1 x Assembly 2 and join these 2 segments together by inserting the free end of top rail C 3 into the free Pod Connector of Assembly 2 as shown in the picture below When connecting the Assembly 1 and Assembly 2 you should see that the spring hole in the square end of top rail C 3 aligns with the free Pod Connector of Assembly 2 Once these 2 segments are connected turn over the remaining 1 x Assembly 1 and 1 x Assembly 2 and connect these segments in the same way You will now have 2 halves of the completed frame Carefully maneuver these 2 halves together and join them again ensuring that the spring holes in the square end of the top rails align with the open Pod Conn2. Pad 12 so the holes align with the Pod Connector 6 as shown so the Jumpking logo covers one top rail E 5 Do not fasten the Surround Pad to the Frame at this stage as this will be done later Assembling the Safety Enclosure You will now assemble the Safety Enclosure for your OvalPOD trampoline Take the enclosure Top Curve Pole 15 and Straight Pole 14 If not already fitted slide the Foam Sleeves 16 on to Top Curve Pole 15 and Straight Pole 14 Find the tapered end of the Straight Pole 14 and insert it into the Top Curve Pole 15 Notes Please read this document in conjunction with the OvalPOD Users Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 11 JUMPIKING Trampolines Then screw the poles 14 15 together using a self tapping screw 21 Repeat this with the remaining poles so you have 8 identical assemblies Take one of the completed Enclosure Poles and carefully lay it flat on the trampoline bed with the end of the Straight Pole 14 towards the Pod Connector 6 at the edge of the frame Then lift the edge of the Frame Pad 12 Carefully push the Straight Pole 14 through the opening in the Frame Pad 12 Then insert the end of the Straight Pole 14 into the opening of the Pod Connector 6 Please ensure that the Top Curve Pole 15 points towards the cen
3. s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Attaching the Jump Bed and the Surround Pad We advise that you wear gloves and protective eyewear for the following steps Take the Stitched Bed Key No 11 and lay it on the ground inside the trampoline frame as shown You will see a series of V rings around the edge of the Jumping Bed Make sure the 2 warning labels are on the top of the bed Find the 2 V rings with yellow stitching These will be located near the warning label at North and South on the Bed The diagram below details the spring attachment sequence To attach a spring 10 first hook the more tightly curled end onto the bed 11 as shown and then use the spring tool 22 to connect iii the spring to the frame iis x Aa AANA Make sure you wear gloves when attaching the springs Please refer to the diagram below for the spring attachment sequence Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines This diagram shows the initial order of spring attachment Top Spring Hole Sliver O Top Spring Hole Yellow O Under Spring Silver Important Attach the
4. the connecting sleeves at one end of the G4 Poles This requires two people Please ensure you wear gloves Each person should grasp the two ends of the G4 Poles 17 and push towards each other as shown This will make it easier to join the 2 x G4 Poles 17 Connect the Top G4 Poles 17 using the connecting sleeve as shown Then connect the 2 x G3 Poles 26 at the bottom of the net When the Poles are connected please close the Velcro flap of the sleeves The Net 18 will now be an oval shape Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 15 JUMPIKING Trampolines The next step is to hang the Net 18 on the 8 x Enclosure Poles 15 First rotate the Net 18 and poles so the zipped entrance of the Net is by the Jumpking logo on the frame pad 12 Locate the 8 x exposed areas of the G4 Pole 17 at the top of the Net 18 as shown Then stand on the trampoline bed and insert the exposed sections of the G4 Pole 17 into the first Plastic Cap 20 of the Top curve Pole 15 Please refer to the below image for the sequence of hanging the Net 18 on the Top curve Poles 15 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD
5. JURIPKING Trampolines This is a supplementary guide to assembling the 10ft x 15ft OvalPOD Please ensure you have read the OvalPOD User s Manual before referring to this guide This document aims to provide a user friendly guide to building the OvalPOD with additional images and alternative techniques Building the Frame W leg Assembly First you will need to assemble the leg bases of your OvalPOD This will require 2 x L legs and 1 x Centre Leg These are key numbers 7 8 and 9 in your users manual Lay out the 2 x L legs 7 8 and one Centre Leg 9 so that it makes a W shape Join the three pieces so the screw holes line up Using a screwdriver screw self tapping screws 21 into the screw holes You have now completed one W leg assembly Repeat these steps with the remaining 3 leg assemblies to create 4 x W legs Please put these to one side Top Rail Assembly Top Rails B A and C Assembly 1 Now assemble the top rails The easiest way to put the trampoline together is in 4 individual segments For the first of these 2 segments please lay out the top rail parts marked B 2 A 1 and C 3 as shown below see drawing 1a on page 15 of the users manual for reference Make sure that the parts are laid out in the order shown below so that 2 spring holes can be seen on parts B 2 and A 1 Also make sure you have a Pod Connector 6 on the left end of part B 2 and on the right end
6. assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 16 JUMPKING Trampolines You will now secure the bottom edge of the Net 18 to the V rings of the Jumping bed 11 Warning Choking hazard small parts Not suitable for children under 6 years Adult assembly only Take the pack of Cord Locks 23 and select a single Cord Lock Pull the black plastic stopper so it is at the bottom of the cord by the two Knots as shown Locate one of the black webbing loops at the bottom of the Net 18 Push the end of the Cord Lock 23 with the single knot through the black webbing loop as shown Then lift the Frame Pad 12 and pass Cord Lock 23 through the nearest V ring of the Bed 11 as shown Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 17 JUMIPKING Trampolines The next step is to loop the free end of the Cord Lock 23 over the black plastic stopper as shown Then hold the two knots by the black plastic stopper and pull the stopper down the cord securing the Net 18 to the Bed 11 Repeat this process with the remaining Cord Locks 23 to secure all of the black webbing loops at the bottom of the Net 18 The Next step is to secure the Frame Pad 12 to the Trampolin
7. e Frame You will find a series of straps and metal D rings around the edge of the Frame Pad 12 Secure the outer straps to the Top Rails as shown Do not over tighten the straps Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 18 JUMPKING Trampolines There is a second series of elasticated straps around the inside edge of the Frame Pad 12 Tie these straps by hand around the nearest spring 10 The final step is to attach the Safety Placard 19 to a top rail by the Net entrance using the included plastic tie Make sure all the parts are securely attached Familiarise yourself and all trampoline users of the trampoline with the Safety Information and the Care and Maintenance details before use You have now completed your OvalPOD Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 19
8. ector as shown above Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 7 JUMIPKING Trampolines You will now have a completed OvalPOD frame Trouble Shooting Should you need to establish if you have correctly assembled your OvalPOD frame you can check that your top rails are in the correct order Start by locating top rail C 3 on your frame this will be the apex of the oval shape Standing on the outside of the frame by part C 3 walk around the frame in a clockwise direction If your frame parts are in the correct layout you should find you have the following order of top rails CBAEDBACBA EDBA Make sure the join between top rails A 1 and B 2 are tight and secure and that top rail A 1 is fully inserted into top rail B 2 Also ensure that the join between top rails D 4 and E 5 are tight and secure and that top rail E 5 is fully inserted into top rail D 4 Do not continue until all top rails are securely joined lf correctly assembled you will find that all of the curved top rail parts will have 2 spring holes on the underside If this is not the case you may have assembled some frame parts upside down Please dismantle you OvalPOD frame and reassemble Notes Please read this document in conjunction with the OvalPOD User
9. g holes can be seen on parts B 2 and A 1 Also make sure you have a Pod Connector 6 on the left end of part B 2 and on the right end of part A 1 IMPORTANT Ensure that part B 2 is fully inserted into part A 1 before continuing B 2 and A 1 must be tightly connected Do not continue until you have a tight and firm connection Please make sure that the spring holes in the square ends of top rails B 2 andA 1 align with the openings in the Pod Connectors 6 as shown below You may have to lift the top rail off the ground to check this Once you have checked the spring holes are correctly aligned with the Pod Connecter 6 push parts B 2 and A 1 together Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines Please connect parts E 5 and D 4 together before connecting part E 5 to the Pod Connector 6 Make sure the reinforcing square sleeve of part D see below is on the left hand end and that top rails E 5 and D 4 are securely and tightly connected inside the reinforcing sleeve IMPORTANT Ensure that part E is fully inserted into part D before continuing E and D must be tightly connected Do not continue until you have a tight and firm connection a Once E 5 and D 4 are connected as above inse
10. of part A 1 IMPORTANT Ensure that part B 2 is fully inserted into part A 1 before continuing B 2 and A 1 must be tightly connected Do not continue until you have a tight and firm connection Notes Please read this document in conjunction with the OvalPOD Users Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Please make sure that the spring holes in the square ends of top rails B 2 A 1 and C 3 align with the openings in the Pod Connectors 6 as shown below You may have to lift the top rails off the ground to check this Once you have checked the spring holes are correctly aligned with the Pod Connecter 6 push parts B 2 A 1 and C 8 together Now retrieve one of the W legs you completed earlier and insert one end of the legs into the Pod Connector 6 of part B 2 as shown in the picture Please note that other end of the leg assembly does not line up with the Pod Connector 6 of part A 1 as shown in the picture Now pull the free end of the leg assembly until it lines up with the Pod Connector 6 attached to top rail A 1 You can place your feet on the top rails either side of the empty Pod Connector 6 to steady the assembly as shown in the image Notes Please read this document in conjunction with the OvalPOD User s Manual This i
11. rt top rail E 5 into the Pod Connector 6 making sure the spring hole aligns with the opening in the Pod Connector 6 Now retrieve one of the W legs you completed earlier and insert one end of the legs into the pod connector of part B 2 as shown in the picture below As previously detailed the other end of the leg assembly does not line up with the Pod Connector 6 of part A 1 as shown in the picture above Please pull the free end of the leg assembly until it lines up with the Pod Connector 6 attached to top rail A 1 You can place your feet on the top rails either side of the Pod Connector 6 to steady the assembly By placing your hands further down the W leg nearer to the Pod Connector 6 you can increase your leverage when inserting the W leg into the pod connector Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Once both sides of the W leg are in push down firmly on the W leg assembly to ensure a tight fit The tension of the W leg assembly helps hold the top rail pieces together Repeat this once more with the remaining B 2 A 1 E 5 and D 4 top rails so you have 2 identical segments Please refer to these segments as Assembly 2 as shown in the picture below
12. s an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines By placing your hands further down the W leg nearer to the Pod Connector 6 you can increase your leverage when inserting the W leg into the Pod Connector 6 Once both sides of the W leg are in push down firmly on the W leg assembly to ensure a tight fit The tension of the W leg assembly helps hold the top rail pieces together Repeat this once more with the remaining B 2 A 1 and C 8 top rails so you have 2 identical segments Please refer to these segments as Assembly 1 as shown below Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Top Rail Assembly Top Rails B A E and D Assembly 2 In the previous you assembled 2 of the 4 frame segments You will now build the remaining 2 frame segments using the top rails marked as B 2 A 1 E 5 and D 4 To assemble these segments please lay out the top rail parts marked B 2 A 1 E 5 and D 4 as shown below see drawing 1b on page 15 of the user s manual for reference Make sure that the parts are laid out in the order shown below so that 2 sprin
13. springs in the order shown in the diagram This will help to distribute the tension making assembly easier Firstly locate the 2 V rings with yellow Stitching These V rings are to be attached at points 1 and 2 using a silver spring 10 Then attach silver springs 3 to 18 in the order shown in the diagram These are all silver top springs 10 Important Remember to include the under spring holes when counting the V rings on the frame and bed Once all of the springs shown in the diagram have been fitted the remaining top springs can be attached including the yellow springs Please attach the yellow springs 13 to the Pod Connectors 6 as shown below ne Pr p ii gt EA gt r 5 M ps oN N i is Wo oe S ANC EN TN wae y r N A N Then please attach the under springs 10 to the underside of the top rail Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 10 JUMIPKING Trampolines Make sure all of the top springs and under springs are attached Warning Do not use the trampoline until the surround pad and the safety enclosure have _ AH also been fitted hie nae i Now take the Frame Pad 12 and spread it out on the trampoline Rotate the Frame
14. tion with the OvalPOD Users Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 13 JUMIPKING Trampolines The G4 Pole 17 will become visible at the opposite end of the Net 18 Then repeat this process with the second G4 Pole 17 in the parallel stitched sleeve at the top of the Net 18 Make sure that you have a connecting sleeve on one of the black G4 Pole sections as shown Then take the black slimmer G3 Pole Sections 26 You will see these poles are connected with an internal elastic cord as shown Please unfold and join the 6 x G3 Pole sections Then repeat this with the remaining 6 x G3 Pole sections in the same way to make 2 x long black poles Take one of the completed long G3 Poles 26 to the Net 18 Then locate the channel inside the stitched sleeve at the bottom of the Net 18 Insert and push one of the long G3 Poles 26 into the stitched sleeve Then repeat this process with the second G3 Pole 26 in the parallel stitched sleeve at the bottom of the net 18 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 14 JUMIPKING Trampolines Now join the 2 x G4 Poles 17 at the top of the net together using
15. tre of the trampoline bed Repeat this step to attach all 8 x Enclosure poles 14 15 as shown Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 12 JUMIPKING Trampolines Now take Safety Enclosure Netting 18 and spread it across the trampoline There is a stitched sleeve at the top of the net and at the bottom of the net Make sure the sleeves are spread out flat across the bed This IMrKING will make assembly easier Then open the PE WORLD FAVOURITE Velcro flaps of the sleeves Now take the G4 Pole Sections 17 Please join 6 x G4 Pole sections in Black Blue Blue Blue the following order Black Blue _ a a a Blue Blue Blue Black Then repeat this with the remaining 6 x G4 Pole sections in the same way to make 2 x long poles Take one of the completed long G4 Poles 17 to the Net 18 Then locate the channel inside the stitched sleeve at the top of the Net 18 Insert and push one of the long G4 Poles 17 into the stitched sleeve as shown This process will be much easier if the Net 18 is flat across the trampoline Make sure the long G4 Pole 17 passes through the semi circular openings and then goes back into the stitched sleeve at the top of the Net 18 Notes Please read this document in conjunc
Download Pdf Manuals
Related Search