User Manual
Contents
1. Vat Drill 008950 ENGLISH Original instructions Model DDA340 DDA350 Steel 10 mm 10 mm Capacities Wood 25 mm 25 mm No load speed min 0 1 700 0 1 800 Overall length 314 mm 314 mm Net weight 1 7 kg 1 8 kg Rated voltage D C 144 V D C 18 V Due to our continuing program of research and development the specifications herein are subject to change without notice Specifications and battery cartridge may differ from country to country Weight with battery cartridge according to EPTA Procedure 01 2003 END004 4 Symbols The following show the symbols used for the eguipment Be sure that you understand their meaning before use Omi Read instruction manual Cd A Ni MH Li ion Only for EU countries Do not dispose of electric equipment or battery pack together with household waste material In observance of European Directive 2002 96 EC on waste electric and electronic equipment 2006 66 EC on batteries and accumulators and waste batteries and accumulators and their implementation in accordance with national laws electric equipment and battery pack that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility ENE032 1 Intended use The tool is intended for drilling in wood metal and plastic ENG104 1 For European countries only Noise The typical A weighted noise level2. OPERATION ACAUTION Hold the tool firmly with one hand on the gripping part of the tool and the other hand on the side grip when performing the tool Drilling operation Drilling in metal To prevent the bit from slipping when starting a hole make an indentation with a center punch and hammer at the point to be drilled Place the point of the bit in the indentation and start drilling Use a cutting lubricant when drilling metals The exceptions are iron and brass which should be drilled dry ACAUTION Pressing excessively on the tool will not speed up the drilling In fact this excessive pressure will only serve to damage the tip of your bit decrease the tool performance and shorten the service life of the tool There is a tremendous force exerted on the tool bit at the time of hole break through Hold the tool firmly and exert care when the bit begins to break through the workpiece A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out However the tool may back out abruptly if you do not hold it firmly Always secure small workpieces in a vise or similar hold down device If the tool is operated continuously until the battery cartridge has discharged allow the tool to rest for 15 minutes before proceeding with a fresh battery MAINTENANCE ACAUTION Always be sure that the tool is switched off and the battery cartridge is removed before attemptin
3. always set the reversing switch lever to the neutral position ASSEMBLY ACAUTION Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool Installing side grip auxiliary handle ACAUTION Always be sure that the side grip is installed securely before operation Screw the side grip on the tool securely The side grip can be installed on either side of the tool whichever is convenient Installing or removing drill bit 1 Chuck key To install the bit place it in the chuck as far as it will go Tighten the chuck by hand Place the chuck key in each of the three holes and tighten clockwise Be sure to tighten all three chuck holes evenly To remove the bit turn the chuck key counterclockwise in just one hole then loosen the chuck by hand After use return the chuck key to the storage cavity on the tool Chuck key holder 1 Chuck key holder 2 Screw To install the chuck key holder fix it to the convex portion of the tool housing on either side and then secure it with a screw To remove loosen the screw and then take it out Hook 1 Groove 2 Hook 3 Screw The hook is convenient for temporarily hanging the tool This can be installed on either side of the tool To install the hook insert it into a groove in the tool housing on either side and then secure it with a screw To remove loosen the screw and then take it out
4. determined according to EN60745 Sound pressure level Lpa 73 dB A Uncertainty K 3 dB A The noise level under working may exceed 80 dB A Wear ear protection ENG202 3 Vibration The vibration total value tri axial vector sum determined according to EN60745 Work mode drilling into metal Vibration emission Ah p 2 5 m s or less Uncertainty K 1 5 m s ENG901 1 The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool With another The declared vibration emission value may also be used in a preliminary assessment of exposure AWARNING The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time ENH101 15 For European countries only EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine s Designation of Machine Cordless Angle Drill Model No Type DDA340 DDA350 are of series production and Conforms to the following European Directives 2006 42 EC And are manu
5. tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Battery tool use and care 24 25 26 27 Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips co
6. CAUTION Before inserting the battery cartridge into the tool always check to see that the switch trigger actuates properly and returns to the OFF position when released To start the tool simply pull the switch trigger Tool speed is increased by increasing pressure on the switch trigger Release the switch trigger to stop A CAUTION Be sure to hold the tool firmly before the tool is switched off Lighting up the front lamp 1 Lamp ACAUTION Do not look in the light or see the source of light directly Pull the switch trigger to light up the lamp The lamp keeps on lighting while the switch trigger is being pulled The light automatically goes out 10 15 seconds after the switch trigger is released NOTE Use a dry cloth to wipe the dirt off the lens of lamp Be careful not to scratch the lens of lamp or it may lower the illumination Reversing switch action 1 Reversing switch This tool has a reversing switch to change the direction of rotation Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation When the reversing switch lever is in the neutral position the switch trigger cannot be pulled ACAUTION Always check the direction of rotation before operation Use the reversing switch only after the tool comes to a complete stop Changing the direction of rotation before the tool stops may damage the tool When not operating the tool
7. connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents 13 Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury 14 Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations 15 Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts 16 If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and care 17 Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed 18 Do not use the power tool if the switch does not turn it on and off Any power tool that cannot 19 20 21 22 23 be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power
8. diately after operation they may be extremely hot and could burn your skin Some material contains chemicals which may be toxic Take caution to prevent dust inhalation and skin contact Follow material supplier safety data SAVE THESE INSTRUCTIONS AWARNING DO NOT let comfort or familiarity with product gained from repeated use replace strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE Before using battery cartridge read all instructions and cautionary markings on 1 battery charger 2 battery and 3 product using battery Do not disassemble battery cartridge If operating time has become excessively shorter stop operating immediately It may result in a risk of overheating possible burns and even an explosion 8 9 If electrolyte gets into your eyes rinse them out with clear water and seek medical attention right away It may result in loss of your eyesight Do not short the battery cartridge 1 Do not touch the terminals with any conductive material 2 Avoid storing battery cartridge in a container with other metal objects such as nails coins etc 3 Do not expose battery cartridge to water or rain A battery short can cause a large current flow overheating possible burns and even a breakdown Do not store the too
9. e housing and slip it into place Always insert it all the way until it locks in place with a little click If you can see the red indicator on the upper side of the button it is not locked completely Install it fully until the red indicator cannot be seen If not it may accidentally fall out of the tool causing injury to you or someone around you Do not use force when installing the battery cartridge If the cartridge does not slide in easily it is not being inserted correctly Battery protection system Lithium ion battery with star marking 1 Star marking Lithium ion batteries with a star marking are equipped with a protection system This system automatically cuts off power to the tool to extend battery life The tool will automatically stop during operation ifthe tool and or battery are placed under one of the following conditions Overloaded The tool is operated in a manner that causes itto draw an abnormally high current In this situation release the trigger switch on the tool and stop the application that caused the tool to become overloaded Then pull the trigger switch again to restart If the tool does not start the battery is overheated In this situation let the battery cool before pulling the trigger switch again Low battery voltage The remaining battery capacity is too low and the tool will not operate In this situation remove and recharge the battery Switch action 1 Switch trigger A
10. factured in accordance with the following standards or standardised documents EN60745 The technical documentation is kept by our authorised representative in Europe who is Makita International Europe Ltd Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD England 30 1 2009 7 Tomoyasu Kato Director Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi 446 8502 JAPAN GEA006 2 General Power Tool Safety Warnings A WARNING Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool Work area safety 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes 3 Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock 5 Avoid body contact with ear
11. g to perform inspection or maintenance Never use gasoline benzine thinner alcohol or the like Discoloration deformation or cracks may result To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized Service Centers always using Makita replacement parts OPTIONAL ACCESSORIES Ac AUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Drill bits Chuck key Chuck key holder Hook Plastic carrying case Various type of Makita genuine batteries and chargers NOTE Some items in the list may be included in the tool package as standard accessories They may differ from country to country 11 Makita Corporation Anjo Aichi Japan 885283 227 www makita com
12. ins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or burns Service 28 29 Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Follow instruction for changing accessories lubricating and 30 Keep handles dry clean and free from oil and grease GEB051 2 CORDLESS DRILL SAFETY WARNINGS 1 2 Use auxiliary handle s if supplied with the tool Loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Always be sure you have a firm footing Be sure no one is below when using the tool in high locations Hold the tool firmly Keep hands away from rotating parts Do not leave the tool running Operate the tool only when hand held Do not touch the drill bit or the workpiece imme
13. l and battery cartridge in locations where the temperature may reach or exceed 50 C 122 F Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out The battery cartridge can explode in a fire Be careful not to drop or strike battery Do not use a damaged battery SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1 Charge the battery cartridge before completely discharged Always stop tool operation and charge the battery cartridge when you notice less tool power Never recharge a fully charged battery cartridge Overcharging shortens the battery service life Charge the battery cartridge with room temperature at 10 C 40 C 50 F 104 F Let a hot battery cartridge cool down before charging it Charge the battery cartridge once in every six months if you do not use it for a long period of time FUNCTIONAL DESCRIPTION ACAUTION Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool Installing or removing battery cartridge 1 Button 2 Red indicator 3 Battery cartridge Always switch off the tool before installing or removing of the battery cartridge To remove the battery cartridge slide it from the tool while sliding the button on the front of the cartridge To install the battery cartridge align the tongue on the battery cartridge with the groove in th
14. thed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded 6 Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 7 Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock 8 When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock 9 If operating a power tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI protected supply Use of an GFCI reduces the risk of electric shock Personal safety 10 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury 11 Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries 12 Prevent unintentional starting Ensure the switch is in the off position before
Download Pdf Manuals
Related Search