Installation Instruction
Contents
1. 2 10 24 x 1 2 Bolts through the side of the front panel and cabinet side Fig 5b Ensure the front of the panel is flush with the front of the cabinet side and screw on 10 24 Lock Nuts to secure the front panel in place Repeat this step for the opposite side of the panel Step 6 Attach U Clips to Base Ends and Insert Side Shelf Bolts Parts Required 2 U Clip Fasteners 8 1 4 20 x 1 1 2 Bolts A Place the two 2 U Clips onto the back of the grill body as shown in Fig 6 Be sure the flat side faces out B Partially insert one 1 1 4 20 x 1 1 2 Bolt into each of the four threaded inserts on the side of the Grill Body as shown in Fig 6 The bolts should only be threaded about half way in Repeat steps 6A and 6B for the opposite side of the grill Page 3 VCS3507 VCS3517 Assembly p FRONT a N e0 Fig 5a VCS3507 VCS3517 Assembly Step 7 Attach the Grill Head to the Cabinet Parts Required 6 1 4 20 x 1 2 Bolts 2 10 24 Bolts Note Two people are recommended to complete this step A Place the Main Unit on top of the cabinet making sure the lid is held shut before lifting B Once the Main Unit is fitted on top of the cabinet insert two 2 10 24 Bolts through the U clips installed at the back of the grill head Securely2. Stainless 2 10 24 Lock Nuts Note Be sure to remove all protective plastic coating from stainless steel parts Stainless Use the two 2 Shelf Supports from step 9 with U Clip 10 24 Bolt fasteners in addition to the two 2 remaining Shelf Supports Each U Clip support is mounted to the rear of 10 24 Bolt the side shelf Secure each Shelf Support to the Shelf by inserting one 1 10 24 Bolt black through the U Clip at the back corner as shown in Fig 10 and one 1 10 24 Bolt stainless through the hole at the opposite end and tighten using one 1 Lock Nut Then repeat the step to secure the other Side Shelf Step 11 Attach the Side Shelves Align the holes of the Side Shelf Supports over the partially inserted bolts from step 6 and gently push down until the bolts settle into the slots at the top of the holes Tighten the bolts fully Next Repeat Step 11 for the other side shelf Page 6 VCS3507 VCS3517 Assembly Step 12 Secure the Side Shelves to the Grill Body Parts Required 2 8 18 x 1 2 Screws 2 10 24 x 1 2 Bolts A Lift the grill lid and insert one 1 10 24 x 1 2 bolt shown as A in Fig 12a to further secure the right shelf to the grill body B Attach the left shelf to the Console by inserting one 1 8 18 x 1 2 Screw as shown in Fig 12b Next Repeat Steps 12A and 12B to secure the right shelf to the gr
3. Signature SERIES VCS3507 VCS3517 ASSEMBLY PROCEDURES Tools Required knife or scissors 2 and 3 Phillips or Robertson square head screwdriver 7 16 and 3 8 wrench or ratchet hammer flat head screwdriver 09 C Step 1 Unpack Carton and Verify Contents Use a sharp cutting tool to cut the straps on the packaging and then open the carton top The sleeve surrounding the barbecue can be removed by lifting it straight up and over the top of the unit Unpack all parts and compare all contents to the parts list that accompanies this assembly manual Next remove the protective plastic coverings from the metal parts Be careful not to scratch or damage the finish of the metal parts when removing the protective plastic Refer to the parts list for fastener detail CAUTION Some parts may have sharp edges to avoid injury wearing gloves during assembly is strongly recommended Page 1 50004061 11 06 Rev 0 En VCS3507 VCS3517 Assembly Step 2 Attach the Caster Inserts to the Cabinet sides Parts Required 2 Cabinet Sides 4 Caster Inserts Insert one 1 Caster Insert into both bottom corners of the cabinet end and ensure they are fully pushed in and engaged Next Repeat this step for the opposite Cabinet Side Step 3 Attach the Cabinet Sides to the Bottom Panel Parts Required 1 Bottom Panel 2 Cabinet Sides with Caster Inserts attached 6 1 4 20 x 1 2 Bol
4. e pan settles into place on the support rails to ensure there will be no leakage Page 9 VCS3507 VCS3517 Assembly Step 16 Install the Internal Components Parts Required 3 Sear Plates 2 Cooking Grates 1 Warming Rack Carefully place each of the three 3 Sear plates side by side inside the barbecue making sure the semicircular finger groove is facing toward the front of the grill Each sear plate rests just above each burner tube Next set the two 2 cooking grates side by side on the upper ledge of the grill tub Make sure the finger groove Warming is facing toward the front of the grill ack Set the warming rack into the supports located on either side of the rear lid ANN _ Cooking Grates Step 17 Install the Battery Parts Required 1 AAA Battery Unscrew the Ignition Button from the console and insert a AAA battery into the housing by placing the positive side of the battery in first Then screw the Ignition button back into the console Page 10 VCS3507 VCS3517 Assembly Step 18A Install the LP Cylinder LP Models Only Parts Required 1 LP Gas Cylinder not included 1 1 4 20 x 2 1 2 Thumbscrew Note Check your user s manual for the cylinder filling requirements how to attach the regulator and how to test for leaks before you try lighting the grill Caution Make sure the hose is not t
5. ill body Page 7 VCS3507 VCS3517 Assembly Step 13 Attach Shelf Insert Note If you have purchased the optional side burner skip this step and refer to the instruction sheet included with the side burner for installation instructions Parts Required 1 Lid S B Single 4 10 24 x 1 2 Bolts 4 10 24 Lock Nuts Note Be sure to remove all protective plastic coating from stainless steel parts Place the Lid S B Single in the opening on the right shelf so it sits flush with the top of the shelf Next attach the Insert to the right shelf using four 4 10 24 x 1 2 Bolts and four 4 10 24 Lock Nuts Step 14 Attach Knobs Parts Required 3 Knobs Align the knobs on the valve stems and push inward until the knob sits snugly on the stem Page 8 VCS3507 VCS3517 Assembly Insert Step 15 Install Grease Cup Cup Holder and Pan Parts Required 1 Pan 1 Grease Cup 1 Grease Cup Holder Attach the Grease cup Holder to the Grease Cup by inserting the vertical prongs through two of the holes in the lip of the Grease Cup on the narrow side Fig 15a Next Attach the Grease Cup Holder to the bottom of the grease pan by squeezing the two hook ends of the holder together until they can fit into the opening of the grease pan H A eS Then slide the grease pan into the two support rails under the back of the grill with the cup and pan opening on the right side Be sure th
6. ouching any hot surfaces Place the LP Cylinder into the hole in the bottom panel Next to secure the LP Cylinder insert the thumbscrew into the threaded hole next to the cylinder holder as shown Securely tighten the thumbscrew Note Ensure all plastic coatings have been removed from all stainless steel parts before using the grill Step 18B Install the NG Hose Bushing Natural Gas Models Only Parts Required 1 Plastic bushing Tools Required Hammer Flat Head Screwdriver Remove the Knock Out Hole from the bottom panel using a hammer and flat screwdriver by placing the screwdriver on the slug and delivering a sharp blow with the hammer Next Snap the bushing into place to line the hole and feed the Natural Gas hose through the opening before connecting it to the gas supply Caution Consult with you local fuel supplier before connecting to the fuel supply Page 11 CFM CFM Corporation i 410 Admiral Boulevard On atu TE Mississauga Ontario L5T 2N6 Canada SERIES 800 668 5323 www cfmcorp com Service Note If you are experiencing difficulties or are dissatisfied with your purchase please contact CFM at the telephone number listed above prior to returning your grill to the store Page 12
7. tighten the bolts C Insert one 1 1 4 20 x 1 2 Bolt into each of the three holes at the top of the Cabinet Sides 3 bolts per side as shown in Fig 7b Do not tighten these bolts yet leave them about 1 2 threaded into the holes Page 4 VCS3507 VCS3517 Assembly Step 8 Install the Front Fascia Parts Required 1 Front Fascia A Slide the Front Fascia onto the two 2 front bolts from Step 7C as shown in Fig 8 Next securely tighten the six 6 bolts to fasten the grill head and fascia in place B Remove the screw shown in Fig 8 from the unit This screw must be removed from both sides A new set of screws has been provided in the hardware bag for when the screws are re installed in Step 12B Step 9 Install U Clip Fasteners to Shelf Supports Parts Required 2 10 20 U Clip Fasteners 1 Shelf Support Left Side 1 Shelf Support Right Side Install the two 2 U Clip fasteners on the Side Shelf Supports as shown in Fig 9 One 1 U Clip should be placed on each bracket with the flat side down Note The remaining Right Side Shelf Support and Left Side Shelf Support do not require U Clip fasteners Page 5 VCS3507 VCS3517 Assembly Step 10 Pre Assemble Side Shelves Parts Required 2 Shelf Supports Right side 2 Shelf Supports Left Side 1 ShelfRight 1 Shelf Left 2 10 24 Bolts black 2 10 24 Bolts
8. ts 8 1 4 20 x 1 1 2 Bolts 14 1 4 20 Nuts ANORA gt A Position the Bottom Panel and Cabinet Sides as shown in Fig 3a and align the holes of the Bottom Panel with the holes in the Cabinet Side B Insert a 1 4 20 x 1 2 Bolt through each of the side holes of the Cabinet Sides and tighten using 1 4 20 nuts for each 3 bolts per side C For each bottom corner of the cabinet assembly insert two 2 1 4 20 x 1 1 2 bolts all the way through the end holes of the Cabinet Side and through the Caster Insert then tighten using 1 1 4 20 nuts for each Step 4 Install the Casters Parts Required 4 Casters Insert the stem of the Caster as far as possible into the bottom of each Caster Insert Ensure the Casters are locked by pushing the locking tabs into the down position Page 2 ANORA gt ANOVRA gt Step 5 Install the Front Panel Parts Required 1 Front Panel 4 10 24 x 1 2 Bolts 4 10 24 Lock Nuts Note Before you install the Front Panel ensure the bottom panel is positioned so the hole for the LP cylinder is towards the back and the smaller Knock Out Hole is to the right of the cylinder hole Note Be sure to remove all protective plastic coating from stainless steel parts Align the holes on the side of the front panel with the holes on the cabinet side making sure that the lighting instructions on the front panel are right side up Next insert two
Download Pdf Manuals
Related Search