user manual
Contents
1. DT 250 Instruction manual AM FM stereo 2 bands PLL Synthesized Personal Radio FM STEREO AM 19 MEMORY PRESETS PLL SYNTHESIZED RECEIVER 000000000000000000000000000 0 000000000000000000000000000 ooooo00000000000000000000000 oooo000000000000000000000000 oooo000000000000000000000000 oooo000000000000000000000000 oooo0o00000000000000000000000 SANGEAN FREQUENCY RANGE FM 87 5 108 MHz AM 522 1629 kHz MY FAVORITE 1 5Vx2 BATTERY SIZE AA UM 3 R6 Controls 1 Headphone Antenna jack To improve FM reception during speaker use leave headphones or external antenna device plugged in through headphone jack Volume Control Rotate the volume control clockwise to increase volume counter clockwise to decrease volume Deep Bass Boost selector Deep Bass Boost provides better bass response Best result will be achieved when using headphones To select Deep Bass Boost slide switch to the left To turn off slide switch to right Power switch Turn the radio on and off For battery saving the radio will auto shut off after 90 minutes operation LCD display will show 90 minutes timer icon You may turn on the radio again pressing power switch if needed Speaker Headphone selector With this selector switch you can choose to use the built in speaker or headphones To use speaker Set selector switch to SP Selection To use headphones a In Stereo Mode set s2. elector to ST If the station is tuned in stereo there will be a headphones indicator with ST on the display b In Mono Mode Set selector to MO LCD display Memory Button Clock Set Band Selection 9 Tuning Up Down 10 My Favorites 11 Lock Switch The lock switch is to prevent unintentional operation of your radio To enable the lock function slide the lock switch to the up position When lock is activated there will be a key icon shown on the display To disable the lock function slide the switch to the down position 12 Belt clip A removable belt clip is provided on the back of the radio It can be removed by gently pushing on the center tab of the clip where indicated and sliding the clip downward towards the bottom of the radio You can easily connect the belt clip by inserting the top of the clip into the designated receiver slots and gently pushing the clip in an upwards motion towards the top of the radio 13 Battery Compartment LCD Display Stereo icon Key locked Memory presets My favorite station Battery power indicator Frequency and Time Band QOmNmoogw gt prenna Battery Installation 1 Open the battery cover located on the radio of your radio by sliding in the direction shown by the arrows 2 Insert two AA UM 3 size batteries one in each compartment Close the battery cover 3 A flashing E appearing on the LCD display indicates a weak batte
3. ng step 2 Change the AM band tuning step from 10 kHz to 9 kHz When radio is off continuously press Tuning Control DOWN button then power on off button for more than 3 seconds until display shows 522 kHz indicating AM step has been changed to 9 kHz step Specifications Band Frequency AM 522 1629 kHz FM 87 50 108 MHz Earphones jack 3 5 mm mini plug 16 ohm impedance stereo Output Power 60 mW 10 THD via built in speaker Speaker 1 3 8 inch diameter 4 ohm impedance Current consumption speaker output AM 60mA FM 70mA Batteries 3 Volts AA UM 3 size x 2 Dimensions W x H x D 64 x 106 5 x 30 mm Weight 108 g without battery If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household MM waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice Waste Electrical and Electronic Equipment Directive
4. ry and that replacement of batteries is required 4 Turn the radio off and replace the batteries within three minutes to avoid reset presets and clock setting during battery replacement Tuning the radio Antenna The lead connecting earphones to your radio acts as an FM antenna when plugged into the headphone jack The lead should be extended as much as possible to increase FM reception There is a separate directional antenna built into the radio for AM reception To achieve the best AM reception it may be necessary rotate the radio Seek Tuning 1 Turn on the radio pressing the On Off button 2 Select desired band by pressing the Band button 3 Press and hold the Tuning UP Down button for approximately 1 2 second Radio will seek for next active signal station 4 Repeat as many times as desired Manual Tuning 1 Turn on the radio select desired band 2 Press Tuning Up Down button repeatedly until desired frequency is found Memory Tuning To tune in stations already programmed into memory See Setting Memory instruction below on how to program stations into radio memory 1 Turn radio on 2 Press My Favorites button MY will appear on the display indicating function is on 3 Press Tuning control UP DOWN to recall memory programmed stations 4 Press My Favorites button to turn off memory tuning Setting Memory 1 Turn radio on 2 Select desired band by pressing
5. the Band button 3 Tune to desired station using either Manual Tuning or Seeking tuning 4 Press Memory button and use tuning controls UP DOWN to reach memory position as indicated on the display 5 Press Memory button again to complete memory setting All together there are 19 memory presets available in this radio Setting the Clock This radio features a clock that will display the current time while radio is off To set the clock 1 Turn radio off 2 Press and hold MEMO CLOCK button until the hour setting begins blinking and the colon is no longer blinking 3 Select hour by pressing the Tuning Controls UP Down button until desired hour is displayed 4 Press MEMO CLOCK button again to set the minutes 5 The minute indicators should now be blinking Using the Tuning Control buttons UP Down until desired minutes is displayed 6 Press MEMO CLOCK button again to complete time setting 7 Time should display solidly with the colon blinking periodically AM tuning step For Northern American countries and some South American countries AM tuning step is 10 kHz On other countries is 9 kHz To change AM band tuning step please follow below steps 1 Change the AM band tuning step from 9 kHz to 10 kHz When radio is off continuously press Tuning control UP button then power on off button for more than 3 seconds until display shows 520 kHz indicating AM step has been changed to 10 kHz tuni
Download Pdf Manuals
Related Search