User Manual - Aldous Systems
Contents
1. To assign access rights to the employees they have to be listed at the access control list of the browser configuration This list could also be modified external and be uploaded to this or another device The browser pages offer extensive tooltips to all fields Enrollment Before the access control can be used the user has to be introduced to the system This process is known as enrollment Therefore open the LCD configuration menu Enrollment with the green card In the top of the display a slide switch is located where the desired type of enrollment can be adjusted By default the slide switch is in the position RFID 17 RFID Enrollment To introduce a new identification card it has to be held in front of the read range of the device The card is stored and a list of available contacts appears With the arrow keys you can assign the card toa contact If a system already knows a card which shall be introduced again the information is given that this card has already been enrolled Face Enrollment available only with the VI FR DS 1 ia making the face enrollment the slide switch has to be slipped to face recognition ENROLLMENT OCO General On the screen the color live image from the camera is displayed The image is overlaid with green guidelines In addition a message appears when you stand too close or too far away At the bottom of the screen a progress bar shows the status of the enroll2. been developed and manufactured in accordance with the following standards transient emissions EN55022 EN61000 3 2 EN61000 3 3 interference resistance EN55024 EN61000 4 2 bis 6 8 11 Note This declaration becomes invalid if the product without the explicit permission of Cortez Connect is modified supplemented or changed in any other way as well as in improper connection or improper use 29
3. GRANTED If an incorrect code is entered there is a message for 2 seconds that the code is not entitled to access Incorrect PIN 22 In the case that the PIN code is entered in the access control list but the check is not set for PIN code the same message on the screen is indicated Multilevel access By combining different credentials such as biometrics card and PIN code a 1 to 3 level access can be realized If the multi level access for a user is set at the browser the credentials must be presented in any order Screen messages prompt the user accordingly to identify with the next credential to gain entry For example when the 2 level access via card and PIN for a user is set up the user is free to initially be recognized at PIN code or card The unit will then prompt the user accordingly to present the second missing credential before access is granted While only one of the three possible credential types is required in 1 level access there are corresponding three possible combinations at 2 level access With a 3 level access all three credentials are required Video surveillance The video monitoring feature allows a visual inspection of the area outside the door over any distance The function of the device is activated by a call from the outside via the SIP or IP address The call takes place hidden so that an active connection to the device is not visible The video monitoring function is not restricted to a
4. of 3D coordinates and the evaluation of the facial features are held in the unit that means it will not require a separate controller or PC RFID and PIN code Additionally or alternatively the access is possible via encrypted RFID cards or tags or via PIN code Audiovisual communication The visitor communication works through hands free talking Meanwhile the built in camera records with 100 degree wide angle lens the situation at the door Intuitive touch screen operation The familiar control of smart phones with a touch screen allows intuitive operation and flexibility for customization Interfaces The devices are connected to the network via Ethernet or a series optionally with 2wire option via a pair of wire and powered with Power over Ethernet PoE Integrated relays and triggers provide connections to doors and or to common doorbell or feedback contact Attractive and functional design The large 5 7 LCD screen allows easy user guidance and representative display of the company logo The high quality stainless steel housing and hardened glass provide protection against damage Equipment overview a Speakerphone for communication and for acoustic feedback b Color camera for communication and camera for biometric c LCD touch screen for user interface and operation d RFID card reader for access via card Place the card in front of this area e Microphone for Voice over IP communication f Terminal block pluggable ter
5. the tree The following description does not constitute a full documentation of the browser configuration as the menus may change in the course of further development of the firmware To assist in the browser configuration so called tool tips appear Positioning of the mouse for 2 seconds on a menu item a small window with an explanation on this point appears The documentation automatically adapts to the capabilities of the device firmware 24 System Administration Ss amp Home select one entry from menu Home woud w gt e o e e Login Logout System information Menu configuration Basic settings Access control TESE E KIE Login System Menu Basic Access Network settings Logout information configuration settings control e e e e SIP configuration Audio Video Interface configuration Upload Firmware Network SIP Audio Interface Upload settings configuration Video configuration firmware Login Logout Password protection On delivery the browser configuration is protected by a password so no unauthorized changes can be done The password can be changed in this menu The password should be kept with care as with a lost password you cannot access the browser configuration Special RFID cards The green and the red RFID card which are delivered can open the LCD configuration or enrollment menus The assignment to these special functions was already done at the factory If yo
6. 55 Tiwa au ieee eee aoe DNS Server 1 DNS Server 2 0 0 DHCP ON D Manual assignment In the DHCP OFF mode you can manually input the IP address Therefore type on one of the sets of numbers of the IP address subnet mask or gateway address Then a 10 key pad is displayed with the numbers to be entered lt q BACK IP ADDRESS Subasi es i Gateway Calan tem eden amia DNS Server 1 0 0 DNS Server 2 0 k 0 The 10 key pad also includes a button to correct the input and an OK button to accept the entry If the OK button is pressed the 10 key pad disappears To enter a full address you can jump from group to group of numbers so the 10 key pad does not need to be hidden in between With the back button you can exit the menu and return to the selection menu 10 Camera The unit is equipped with a wide angle lens covering the space with a horizontal angle of about 100 degrees Depending on the application it may be advantageous that only a specific area in front of the entrance displays for example to receive a larger picture from the person located in front of the device The screen in this menu always shows a scaled live picture of the portrait camera in the correct aspect ratio of 4 3 as it would appear in use on a videophone or on a PC monitor This is for monitoring the selected zoom amp pan settings Pan area By tapping the picture with your finger you can move it as you want providin
7. Start of operation For all mounting instructions please see the installation manual The device can be configured before or after mounting The device has no separate power switch so it cannot be accidentally switched off After the power supply has been established see installation manual the device starts and the home screen is on the display Wednesday 14 11 2012 11 08467 seeee HgoorTbell eeee Phonelist In the upper right corner you can find the date and time display In the middle there is the call button and at the bottom a button for PIN code for the phone book function and the face enrollment guidelines Available only with the VI FR DS 1 For further use of the device configuration is required The devices have two different configuration areas Configuration via LCD screen Via the LCD screen settings can be made that require direct access to the device such as the teaching of ID cards enrollment Other points can be set directly on the LCD screen but can also be configured via the web interface such as the adjustment of the screen brightness Configuration via web browser Via the web browser all settings except the enrollment can be done Some settings such as the display brightness can be set either via the LCD menu or the browser However the setting of this example is more feasible locally because the settings are directly controllable Special RFID cards Both cards have already been
8. Visualint VI EN DS 1 and VI FR DS 1 Manual Visualint www visualint net Visualint 12355 US Highway 301 North Parrish Florida 34219 Tel 941 225 4925 Email sales Visualint net VI EN DS 1 and VI FR DS 1 Attractive all in one system for access control and door communication Stand alone solution without a PC or separate controller Visualint Table of Contents ADOUCIR POUC piss onria ssasavcianiciaveyiatetcisatersounitseuiasunribincierieusserawartueninusccoures A O 5 Wan IVIGU CIN oriras E E 7 Start or operat Oiss EEEE 8 installing VISICOr COMMUNICALION vcsisisccvcvcsessiacrenseascavnsedsnvesvictianinessacnanesdswcasieaanenteteceoneniesseetibestsnaedeudne nines 14 WISIN vistor COMMUNICATION cisccscanteccecsancsscanscevasascessmaceesescasisedescscncesctosseunesuasscsnncecsseieasenesaapesusanetscsasescenssenesessanas 14 Installing access control sssesesesscesscecscecscecececececesecesesesesesesesesesesesesesesesesesescscecscecscececececececececesecesesesesesesesesese 17 Using ACCESS CONTI Ol siesigsacsciwiadecvinsiesenianadaa ecatnivacudubansieesaiaeesinaacewdsnaadasdienaviauadeniniaveasannisseviinadaileiectiniwtiistidenineless 19 Video SURVC IN ANC O sssini A EEE EA EAA ANAA 23 Extended c nfiguration Vid DIOWSEN da iiansiasiucsiwinancersvccssencnsvavinigassecwidannodinv inn e orron Inr NSE I TEAREN D NEA a iora 24 IOS SAN aaa E E eigseees 27 D claration Of CONTON Y osrin E EEA ASS 29 About this
9. ardized in the re commendation G 711 by the ITU T By this analog voice signals are converted through the digitization with a non linear quantization the so called A characteristic curve into digital signals The aim is to achieve a higher dynamic range with the same number of binary digits per sample or a larger signal to noise ratio in which the large signal excursions have coarser and small signal excursions have finer resolutions law In North America and Japan the law related method is used similar to the A law but not compatible Baud rate Describes the number of symbols transmitted per time unit The baud rate is different from the lower data rate by the ratio of the number of symbols per transmitted data bit The baud rate must be set equal on both sides when communicating via a serial interface 27 DHCP Dynamic Host Configuration Protocol allows the assignment of the network configuration to devices by a DHCP server In this setting the user must not set the IP address and other addresses by hand DNS Domain Name System Service on the network mainly for responding to requests for name resolution This device can be addressed with a plain text name that is easier to remember and characterizes the device Here the name remains the same even with changing IP addresses Intercom A station with microphone and speaker that provides and audio and often an audio visual communication to a remote site LCD Liquid Crys
10. be made With the back button you can exit the menu and go to the selection menu Display The adjustment of the display brightness is best done locally because you can only there take into account the direct influence of the ambient brightness The adjustment of the brightness however is also possible through the browser configuration 12 Automatic mode When delivered the slide switch is set to automatic In this setting the display brightness is automatically adjusted to the ambient brightness The determined brightness is shown in the display by the sliding switch This setting has the advantage that the display is automatically dimmed overnight and thereby power consumption is reduced while the display s life is extended lt q BACK DISPLAY Automatic a 11 Manual mode If the automatic brightness control is not desired the slide switch is set to y manual In this setting the control knob of the slider appears which allows the free choice of brightness With the back button you can exit the menu and return to the selection menu Sabotage protection Tamper The device is equipped with a tamper switch After installing the device the two security screws on the bottom edge must be screwed with the provided socket wrench as described in the installation manual In the final position the tamper switch is closed This can be checked on the present menu If the area shown below the lettering tamper is gree
11. by a ringing tone and an animation of the ring button At the same time the text Calling Doorbell appears under the ring button Tapping again interrupts the animated doorbell and an existing connection The bell returns to the idle state the output of the ring tone stops and the message Call cancelled Doorbell is displayed for a set time If the call is accepted by the other side the text Connected Doorbell appears and the green earphone is displayed Now there is a two way audio connection and a conversation can be made If there is a videophone or a soft phone with video functionality such as the Cortez Connect DoorKeeper at the remote site the video image of the color camera is transmitted During an active call various control functions are possible to open the door and to zoom the camera or change the view This is described further below The existing connection can be closed both from the device by tapping the call button blue lettering Hang up and on the remote side In both cases for a certain time the text Connection cancelled Doorbell appears Then the button appears in idle state again If an active call is not answered within an adjustable time SIP call timeout from the opposite side there is no connection The message No response from Doorbell appears before the device returns to the idle state Dialing from the phonebook 15 In addition to the ring button the device offers an integrated phon
12. ebook in which the contact persons of the company are listed See installing access control The phonebook button may be labeled with any text The figures show the label with the text Phonelist The phone book is accessed by tapping the phone book button at the bottom of the ring button With the back button on the top left the phone list can be left and switched to the home screen again The entries in the list appear in alphabetical order However only those entries are shown in which was set the check in phonebook in the configuration If the list contains more items than can be shown an ABC index bar is displayed on the right side By tapping you can activate individual letters areas The scroll function is caused by the vertical sweep of the list with your finger When you tap an item the contact person is called The selected entry is thus opened and a text will appear that describes the currently performed action In addition a button to end the call or the conversation is displayed The following figures illustrate the process In the example the entry Empfang is tapped First the call is started which is indicated by the text Calling Once the connection the text changes to Connected with After the conversation either determined by the receiving station or by tapping the Cancel call button the text Disconnected from is shown for a set time The screen automatically returns to the home scr
13. een with doorbell button If there is no connection possible for a given time the text No response from appears Then the original phone book list appears again Control during the connection If there is an active connection from the device to a phone videophone or soft phone commands can be entered during the call via the telephone keypad Depending on the terminal it may be necessary to unblock the transmission of keyboard commands during a connection first This should be described in the user manual of the phone under SIP Info or DTMF Signaling Except for the opener functions the commands require a videophone or video enabled soft phone to use the video controls Door opener The pound key activates the built in relay of the device Usually the door opener is connected there On the screen a message appears Access granted 16 SDEF Zoom in Higher magnification of the image but with a smaller cut details can be picked up in the picture Swxvrz es ae Zoom out Lower magnification with larger field of view it gives you a better overview 2 ABC Bruv GHI mno oa pi sis Pan function The magnified image can move up down left and right HJKL Center The image will be centered O 1 7 pars n 7 Position buttons The view positions 1 3 stored in the device are available via these keys The key is used for video surveillance Installing access control Input of employee data IMPORTANT
14. enrolled in the factory to be used directly see RFID Enrollment With the green card the unit is set into enrollment mode With the red card the unit is set into configuration mode If there is no active input via the touch screen during these modes you will leave the opened mode automatically after a period of 30 seconds and the home screen appears again This is for safety so that the opened mode doesn t remain activated unintentionally for a longer time If you want to make further settings you must use the green or red card again Configuration via LCD menu With the red card you can configure the following sections Camera Audio Display IP Address and Sabotage protection By tapping the appropriate entries the desired menu appears IP address So that the device is addressed in the network and later the browser configuration can be carried out the IP address of the device can be adjusted The IP address is usually provided by the system administrator of the company Automatic assignment Basically the IP address will be assigned automatically via DHCP or manually Therefore there is a slide switch in the middle The advantage of the automatic assignment of the IP address in DHCP mode is offset by the disadvantage of changing the IP address When set to DHCP ON the assigned address will appear in this menu In this case the address fields for the direct input are disabled lt q Back IP ADDRESS Ie i 2255 2
15. enu Audio Volume Because of the great influence of the mounting location on the acoustic properties the audio settings should be made on the LCD menu The values however are also accessible through the browser configuration 11 Automatic Gain Control In the top half of the menu is the slider for the volume setting The volume can be set between the limits of the min and max based to the local conditions and the preferences of the user If you move the slider a voice recording is played to assess the volume N Microphone In the lower half there are the settings for the microphone sensitivity The 4 sensitivity offers two options a digital control and an analog gain If the local acoustic conditions vary greatly it is recommended to turn on automatic adaptation Change the slide switch labeled automatic gain control The digital gain ensures that it is adjusted to a certain extent and to avoid clipping The sensitivity of the microphone can be selected independently of whether an automatic adjustment has been selected or not with the slider The analog pre amplification of the microphone is now adjusted When delivered a mean value is the default which should be suitable for most applications Especially in very quiet or noisy environments the speech intelligibility can be improved by varying the sensitivity Because of the individually very different acoustic conditions no general requirement for the best setting can
16. g you have zoomed in before That means that the horizontal button is not at the left end Zoom slider To adjust the magnification electronic zoom takes the horizontal slider On the left end the maximum wide angle representation is selected Moving the slider to the right you can zoom in to the picture Here the image section decreases Now the image can be shifted within the window depending on the desired image If the slide is in the rightmost position the maximum magnification is reached When delivered the unit is set to maximum wide angle without any zoom and pan Usually the image section should be chosen so that a person in front of the station is shown clearly visible Save image positions Three different zoom pan settings can be stored in the device as fixed positions These positions can be called up quickly during an active connection from the receiving side You can typically save an overview display and two detailed views of the situation in the entrance area which can then be accessed for inspection The stored position under key 1 is displayed as the default view for a video connection To save a selected zoom amp pan setting press one of three buttons below the slider position until a beep sounds The beep indicates that the setting has been saved To check you can access the settings by briefly pressing without beep the key position again With the back button you can exit the menu and go to the selection m
17. gement of data and authentication of users 26 Audio Video All settings for audio and video transmissions can be edited here In addition a live video stream and stored fixed positions in the device can be displayed if required Interface configuration The device has several inputs and relay outputs that can be extensively configured The available resources for the connection link target must have been previously configured with details of the SIP URI in Access Control Upload firmware With Upload a new firmware can be programmed into the device The already installed firmware version can be read in the browser menu System information While performing a firmware upload ensure that the unit is not disconnected from the power supply Only after the new firmware has been programmed and the automatic restart of the unit is completed the supply voltage can be separated Configuration and access control list files can also be uploaded or downloaded This makes it possible once set or stored data via Download and Upload transmit to other devices The download of the configuration data is recommended not only for safety reasons backup but also if you want to configure multiple devices of the same kind and do not use the Cortez Connect software FaceAdmin Glossary A law The A law is a method of digitization process for analog audio signals in the telecommunications sector used primarily in Europe which is stand
18. he screen turns from white to blue By clicking the face icon a positioning help can be shown As with the enrollment the live image of the camera is shown with superimposed guidelines The green brackets provide guidance for optimal positioning in front of the camera of the device For successful face recognition a confirmation screen is displayed for an adjustable time containing the image of the person entitled user data and the message Access granted After that the start screen appears again Tips for rapid identification The right distance from the device is about an arm s length Therefore put the thumb of an outstretched arm on the edge of the device You should look vertically at the camera above the display For this purpose it is usually necessary to lower his head slightly as the device is mounted slightly lower for size compensation Rapid changes in the facial expressions or the whole position or an enrollment deviating expression impede the rapid recognition Also talking can prevent the detection since the tension of the face muscles change the 3 D shape so that no sufficient match results with the stored characteristics are found The enrollment and the recognition must be made without glasses firstly reflections of the built in lighting invisible infrared light could interfere with the detection on the other hand the 3D shape of the glasses and the glasses frame is also stored as a feature So especially fo
19. indows Mac or mobile devices iOS Android that can be set up as audio visual remote sites After installing the DoorKeeper software it is sufficient to put a check at the respective doors to be informed of door calls For details see the DoorKeeper documents Installing phonebook To see entries of the access control list in the phonebook you have to set the check in Phonebook at all desired entries This is only possible with a SIP URI which means the SIP phone number of each entry Using visitor communication The intercom feature is used to communicate with visitors who want to talk to a special person of the company Through the implementation of the voice over IP protocol SIP the device is compatible with modern video telephony infrastructures There is no need for an additional terminal on the extension side as the call can be routed to each voice over IP terminal which can be reached via the network and SIP The intercom feature is controlled by the operation of the ring button or by selecting a contact person from the phone list Ring button 14 The home screen of the device shows in the middle of the screen one symbolized ring button which can be individually labeled In the following description it is assumed that the ring button is labeled Doorbell Wednesday 14 112012 1108461 Phonelist By tapping the screen in the call button area the connection is started An active call is illustrated
20. io connection is terminated Now the video surveillance function is available again for more than one observer and the display goes back to the main screen Extended configuration via browser The complete configuration of the device is done by using a web browser For this purpose the device has a built in HTTP server The configuration is divided into different menus for each respective websites are available To use the convenient configuration via a web browser you must have connected the device to the Local Area Network LAN and a valid IP address for the network must have been configured as described in the previous chapter Furthermore the PC on which the browser is running and which will be used for the configuration has to be connected in the same network so that the IP address of the device is achievable l cet Basically changes are applied only after pressing the respective assigned Set button If pages are left without setting all changes made will be lost Home screen By opening the browser and entering the IP address of the client device for the first time the website of the device appears The basic design of the screen for all menus consists of the following elements Bar at the top of the screen with a company logo Tree bar on the left with the hierarchical representation of all menus Main window for the configuration menus The configuration menus can be selected either by using the icons in the window or on
21. ish but also German and French menus as well Unit date and unit time The device has an internal real time clock buffered and even continues if the event of power failure or when transporting the device some time more than 1 year Access control In the list view a list with last names and first names is shown Depending of the screen size and the browser window only the first entries are displayed By pressing the scroll bar on the right side you can go to the desired section of the list With the arrow keys you can browse the pages Use button Change to display the contact details Network settings The input of the network settings is analogous to the input on the LCD configuration There exist the same entries IP address subnet mask gateway address DNS server 1 and 2 Auto IP DHCP on off Additionally the name is entered with which the device appears on the network spaces are not allowed The change in the network settings should be done with special care because by entering incorrect values the unit may no longer be accessed from the browser In this case the correct address must be re entered via the LCD menu SIP configuration The intercom functionality operates on the Voice over IP standard SIP Instead of the cumbersome IP addresses short numbers or text name can be used for dialing Second the SIP server offers several convenience features such as an answering machine for audio and video centralized mana
22. m red through yellow to the green zone Sequence of enrollment Important for the rapid flow of enrollment is that the positioning of the face during the enrollment will retain Little movements up or downward to the left or the right are appreciated to ensure the software to store as much face details as possible Please do not talk during the enrollment as these influences your face expression The progress will last about 20 30 seconds in total The progress bar shows progress and quality of the enrollment If an enrollment is determined without reaching the green sector the enrollment has to be redone A list with the available contacts is shown With the arrow keys you can assign the face image to the corresponding contact If the device is operated in server mode in conjunction with the Cortez Connect management software FaceAdmin the enrollment has to be unlocked for these contacts in the software For more information please see to the documentation for the FaceAdmin Upon successful storage of the data the color of the field changes from yellow to green With browser configuration the default user name can be changed and personal information can be completed The check access via face is automatically set at the respective entry at the access control list After completing an enrollment a new one can be done directly Using access control The unit offers for the field of access control three technologies that ca
23. manual This product is manufactured with modern manufacturing techniques and extensive quality assurance measures If you have questions about your device please contact your sales representative Visualint is constantly working on the development of devices and versions We reserve the right to make changes in the scope of delivery technology and equipment No claims shall be made from any text and illustrations of this manual About this product The devices of the VI FR DS 1 and VI EN DS 1 family are new access control terminals which elegantly combine access control and visitor communication You gain a representative business card at the front door of your company The VI FR DS 1 access control solution operates on the basis of a face recognition method which measures the face three dimensionally and grants the highest possible security against unauthorized access at the highest possible comfort hands free operation In addition all devices offer the access option of a RFID card and or a PIN code At the same time they also allow audiovisual communication Visitors can connect to the reception desk or a contact person The operation is performed intuitively with a touch screen The data connection is via Ethernet and is compatible with modern voice over IP SIP standard Integrated interfaces support connections of external components Features Integrated Face Detection Available only with the VI FR DS 1 The calculation
24. ment The enrollment consists of three steps Geometry capture Here the three dimensional measurement of the face and the calculation of the biometric features are made Features check The biometric features gained in step 1 are reviewed in terms of the quality and completeness Data storage The biometric features are stored in the database of the device Positioning The green lines and the messages provide assistance to the position of the face in front of the device This learning process is also used to get to know the approximate distance from the subsequent use of face recognition The green brackets indicate that the device has found the face and now follows the position of the face in the image The facial expressions in front of the camera should be neutral at best Although precautions have been taken by the software that the facial expressions have no effect for the calculation of facial features a 18 neutral facial expression improves the recognition performance of the device The facial expression should be preferably matched to the expression with which you want to be recognized in the daily use If the distance from the device is too large not enough features can be recovered for recognition In these cases the text message will appear Step closer If the face is too close to the unit the message Step back is issued With a proper position in front of the unit no message is sent and the progress bar moves fro
25. minals for external power supply and interfaces g Ethernet Network connection to the power supply Power over Ethernet and network connectivity h Wall mount holder can be used as a drilling template or back housing Content of delivery for VI EN DS 1 VI FR DS 1 Mounting kit Dowels and screws for wall mounting socket wrench for housing locking or opening seals Terminal block Types PTR AK1350 series Network cable Patch cable for Ethernet connection RFID cards Green and red card with special functions for log in to configuration and enrollment sites grey card for visitor ID card Manual Installation manual Wall Mounting Cut out for flushing mounting 124 x 244 47mm 4 8 x 9 6 x 1 85 in Further details on datasheet at www visualint net w j e 1 Separate housing front from housing back Loosen sealing screws 2 Move housing front upwards and unhinge it 3 Put cables through rubber seal 4 Put rubber seal with cables through the desired housing LS opening and snap it in f 5 Mounting housing back a Flush mounting in cavity wall If you use the outwards screw holes close the inwards screw holes with attached rubber seals b Flush mounting in solid wall c Surface mounting 6 Plug in desired connections 7 Place housing front on fulcrum pins and move it downwards 8 Tighten sealing screws to fix the housing front with the housing back
26. n the tamper switch is closed providing security against theft of the device If the area is red the tamper switch is open Removal of the device cannot be detected In this case the security screws have to be screwed until a faint clicking sound indicates the switching of the tamper switch and the area is shown in green 13 Accelerometer The built in acceleration sensor in the device measures changes in the orientation of the device in all three spatial axes The movement of the device to the axes x y z are represented as level indicators When a display changes in the red zone an alarm can be generated as at the tamper switch The acceleration sensor is primarily used to detect a theft without unscrewing the device or vandalism With the alarm message an alert to a control center and or a video recording of evidence can follow Installing visitor communication LCD display settings The start screen and all labels of the LCD menu can be adjusted via the browser pages of the device please insert IP address first The browser pages offer extensive tooltips to all fields Installing destinations To label the ring button and to fill the phone book with entries you have to install destinations This is made via the browser menu Access control see Installing access control As an alternative or in addition to a fixed remote station for the doorbell you can use the Cortez Connect software product DoorKeeper for W
27. n be used for entrance allowance Face recognition Available only with the VI FR DS 1 is a biometric method in which the three dimensional shape of the face is detected Biometric methods do not require any identification card and are therefore extremely safe because a loss or theft is eliminated Face detection also offers the advantages of convenient operation without a free hand and touchless hygienic operation 19 RFID is a modern smart card technology which also works without contact By encryption techniques high security is achieved In the future mobile phones will work according to the present standard NFC and can then be used as identification PIN code is a fairly simple process in which the knowledge of a number sequence is used as permission As the sequence of numbers may also be guessed or tried the security level here is relatively low Access via face recognition Available only with the VI FR DS 1 After the implementation of enrollment and the assignment of the employee data at the access control list the face recognition can be directly used Starting from the basic mode of the device start screen the face recognition works automatically therefore the device looks for the presence of face in the viewing area of the camera If a face is found in sufficient size the unit attempts to identify the face If a face is found in the range of the camera the color of the face icon in the lower right corner of t
28. r large fashionable glasses the recognition accuracy could be compromised 20 Access via RFID The device behaves in relation to the access via RFID card as a conventional card reader The access card is held just in front of the field marked with the RFID symbol The card does not need to be placed on the device but will be detected at a distance of 1 to 3 cm from the device If an enrolled card is detected the access is granted RFID AUTHENTIFICATION Identified Address Last name von F rth First name Rafael Pers ID 99 A ACCESS GRANTED If an unknown card held in front of the reader the screen message card not in system appears Card not in system UID OA4CDC71 If the card is indeed known to the system but access is blocked tick in the access control list is missing this is indicated by the following message on the screen 21 Access with RFID for User not activated Access via PIN code While access via RFID requires the possession of the correct card the access via a PIN code requires knowing the correct code By clicking on the PIN icon in the lower left corner of the screen a 10 key keyboard is displayed A mistake can be undone with the Corr The entry is completed by pressing the OK button If the code is entered correctly the access is granted PIN AUTHENTIFICATION Identified Address Last name von Firth First name Rafael Pers ID 99 ACCESS
29. single observer but up to 10 remote stations can simultaneously receive the video image from the door As described above the video parameters can be changed during the call so you can pan the camera from a distance and tilt or zoom into images or zoom out for an overview see Control during the connection It should be noted that this possibility deserves all observers across multiple active peers Therefore concurrent requests can be sent by the observers on the camera of the terminal If the camera of an observer is set to a fixed position it is quite possible that another observer chooses a different position and zoom setting The audio transmission is initially turned off for privacy reasons i e there is no acoustic monitoring of the entrance area The bidirectional audio connection must explicitly be unlocked from the opposite side and then the terminal is also displayed A person in front of the terminal can see that the microphone was turned on With the audio connection all other video connections that may have been installed are stopped so that the connection will be exclusively assigned to the observer who requested the audio connection Speaker on off By tapping the star button during an active video connection the audio connection is bidirectional and the AV connection is exclusively assigned to the requesting 23 remote station The terminal screen is switched to CONNECTED By re pressing the star button the aud
30. tal Display often colloquially referred to as flat NIR Near Infrared invisible to the human eye in the near infrared light range OSDP Open Supervised Device Protocol is an approach to standardize the connection of peripheral devices in the field of access control and alarm systems and to enable collaboration between devices from different manufacturers PIN Personal Identification Number is a number known by only one or a few persons with which they can be authenticated against a machine RFID Radio Frequency Identification a modern smart card system for access control SIP Session Initiation Protocol is a network protocol for setting up controlling and terminating a communication session between two or more participants In the IP telephony SIP is a frequently used protocol UID Unique Identifier a unique and distinctive number which allows the authorization of a card to the reader This number consists of a fixed number of characters and is awarded only once URI Uniform Resource Identifier consists of a string which is used for identification A SIP URI is used for addressing participants of SIP based calls It is thus the SIP phone number of a participant 28 Declaration of Conformity Visualint 12355 US Highway 301 North Parrish FL 34219 Declares that the devices VI EN DS 1 VI FR DS 1 comply with the requirements of the directives on electromagnetic compatibility 2004 108 RG and has
31. u want to use other cards for these functions you can change the assignment as follows Option 1 First the two UID entries are deleted Pressing the set button the card detection system for opening the configuration and enrollment menus is started Then the green card to open the LCD configuration has to be put in front of the reader A message will appear if the card has been detected The red card to open the enrollment has to be put in front of the reader Two new UIDs are entered and the unit will operate normally To display the new UIDs in the browser the browser page has to be reloaded Option 2 The UIDs for the two special cards can be entered in the appropriate fields Manual entry of the UIDs always carries the danger of incorrect entry Therefore option 1 is always to be preferred System information The system status menu is divided into the areas of system data and system log 25 The system data contain information about the device type the hardware address and software version of the firmware For service purposes the built in hardware components may be displayed Please contact your system administrator for questions regarding the syslog protocol Menu configuration The appearance and the caption of the LCD screen can be adjusted with input of your personal preferences on this page Basic settings All general device settings have been grouped under this menu Language selection The device supports not only Engl
Download Pdf Manuals
Related Search