Sasquatch 1000W
Contents
1. 1 Seat 8 Front Shock Absorber 2 Taillight 9 Tire 3 Rear Wheel 10 Headlight 4 Hub Motor 11 On Off key switch 5 Controller inside 12 Handlebars 6 Battery inside 7 Battery Carrier with lock Diagram 2 The Handlebars and Controls This diagram illustrates the various parts of your ATV Please note that many of these parts are not user ser viceable and should be repaired only by trained professionals This is especially true of the electrical systems and the mechanical components 2 3 1 5 6 7 1 Accelarator 4 LED switch 7 Speed Indicator 2 Front brake controller 5 Horn 3 Rear brake controller 6 Speedometer gt DAYMAK Riding Instructions This guide assumes that you already know how to ride a standard ATV Before you try to ride an electric ATV you should be very familiar with controlling and balancing a normal ATV Caution If you do not have riding experience an e ATV is too dangerous to ride Do not begin learn ing to ride a ATV using an e ATV Important Notes E ATVs are Fast E ATVs are capable of traveling at higher speeds than many rid ers are accustomed to Use caution at all times especially when travelling in mixed traffic Always take into account driving and traveling conditions Obey the Law Be sure to follow all provincial and city tr2. is registered and you are licensed to drive gt DAYMAK The Brakes Front Brakes The brakes on your e ATV are drum brakes like those found on gas scooters and motorcycles They generally provide for very fine stopping and control This is a very tested and well designed technology but even so the brakes will require servicing from time to time and may have to be adjusted for tension Unlike normal friction grip ATV brakes which clamp down from the outside the drum brakes clamp from the inside When the brakes are activated tension increases and the clamps engage This is a very effective and reliable way to stop a vehicle The brakes are contained within a sealed unit and are very finely adjusted and fitted Rear Brakes The rear brakes on your e ATV are EABS Brakes Electric Absorption Braking System These provide a good friction grip when they are activated They significantly less than standard drum brakes Using these brakes helps to reduce the weight of the e ATV and improve its performance Shock Absorbers Your e ATV is equipped with Reverse Shock System shock absorbers These effective but simple devices ab sorb the energy from bumps and dips and allow you to have a much more comfortable ride The Reverse Shock System is superior to normal Monoshock shock absorbers usually found on e ATVs and provides for a much more comfortable ride While they are very resilient please note that very sharp or large shock
3. could also cause your motor to work too aggressively and it may burn out Disconnecting the Circuit Breaker When the circuit breaker is disconnected all power from the battery to the e ATV is blocked This is useful if you are going to store your e ATV or if it is damaged and you wish to bring it to be serviced Disable the circuit breaker using the following very simple procedure 1 Open the seat compartment 2 Find the circuit breaker switch it should be very obvious 3 Activate the switch The power to the e ATV will be disabled Long Term Storage of your E ATV If you are storing your ATV for a long period disconnect the circuit breaker This is a safer way to store the electric ATV as it prevents accidental activation of the e ATV and makes it impossible to activate it even with the key The circuit breaker is found by opening up the battery case It sits between the battery and the controller Please see the section titled Your Battery for instructions on battery maintenance while your e ATV is being stored Your e ATV may or may not have a circuit breaker gt DAYMAK 11 The Battery This section details what you need to know about the battery that powers your e ATV Al ways remember to treat your e ATV s electrical systems with respect Battery Power The dashboard has a battery charge indicator When the e ATV is activated the needle will jump and indicate the currently available battery power If
4. dealer Warning Be absolutely sure that you replace the battery with an identical or very similar battery While it is possible to change the battery format or power levels this requires advanced knowledge of electrical systems If improperly done this can result in immediate and irreparable damage to the electronic controller and electrical systems Be absolutely certain of what you are doing before you replace the battery with a different type of battery Using the wrong type of battery will also void your warranty gt DAYMAK Technical Data This section provides you with the technical specifications for your e ATV The Motor and Wheel Assembly The Smart ATV has a 800 Watt magnetic DC brushless motor on the rear wheel hub This type of motor has excellent low end torque and high efficiency when working within its range Note that while the motor is very quiet it does produce some noise Also attached to the rear hub are speed reduction gear and the speed free clutch The Freewheel The wheels have freewheels so the e ATV s drive train is not fixedly geared This means that when coasting or traveling downhill you can turn off the engine and your e ATV will continue to move without slowing This feature will allow you to achieve faster speeds when coasting moving downhill or moving with the wind It will also allow you to conserve electrical power because you will be able to let to the motor rest while moving Th
5. electrical outlet Charger Warning Only use the chargers that were supplied with your e ATV Using chargers that do not have specifications identical to those which came with the e ATV could irreparably damage your e ATV s battery and electrical systems and may cause injury To charge your e ATV follow these steps 1 Turn off the e ATV and remove the key from the ignition 2 Plug the female end of the charger cable into the charging slot on the e ATV This is found on the outside casing of the e ATV in front of and just underneath the seat 3 Plug the male end of the charger power cable into your wall socket This should be a110v household electricity supply You can also use a portable generator if necessary but make sure it provides 110V current 4 Allow the e ATV s battery to charge for the appropriate amount of time 6 12 hours 5 Disconnect the charger when the LED light on the charger is green The batteries have been fully charged If your charger s LED status light does not change from red to green over an extended period of time for perhaps more than 14 hours and the battery is very hot the battery or charger may need replacing Stop charging and bring both to your Daymak dealer imme diately Do not charge the battery gt DAYMAK Battery Care Follow these suggestions to maintain your battery s optimal performance If you do not follow these suggestions your battery may lose its ability to maint
6. highly trained tech nical skills of our staff and careful ongoing design work by our engineers We hope you enjoy using this product and welcome any feedback that you may have New Laws Please check with your provincial or state government to learn about your local laws At the back of this manual you will ind the some of the common Canadian provincial regula tions that govern e ATVs Liability Daymak does not assume any liability for damages loss of profits or claims from third parties due to improper use of this product Daymak does not assume any liability for dam ages due to problems with the product resulting from service by a third party that is not certified by Daymak The information in this guide may be subject to change without notice For the latest infor mation available please contact your local Daymak dealer or visit our website We have taken all possible measures to ensure the accuracy and completeness of the in formation in this guide However if you do find anything missing incomplete or wrong do not hesitate to contact us O DAYMAK ATV Part Diagrams Diagram 1 The Sasquatch Youth 1000W Electric ATV This diagram illustrates the various parts of your ATV Please note that many of these parts are not user ser viceable and should be repaired only by trained professionals This is especially true of the electrical systems and the mechanical components
7. listen for changes in the sounds your e ATV makes over time Any mechanical or power issues may have effects on the sounds the ATV makes Holding the Handlebars As with a normal ATV or gas scooter place your fingers over the brake levers using the palms of your hand and your thumbs to wrap around and under the handlegrips Doing this allows you to activate the brakes easily by squeezing your hand in case you have to stop quickly This is the safe way to control your electric ATV Turning your E ATV On and Off To turn on your e ATV insert the key into the ignition located just below the dash board and turn the key to the right When your e ATV is activated the power indicator will light and the battery charge indicator will jump showing you how much power your e ATV has To turn off the e ATV simply turn the key to the left and remove the key Warning When you activate the e ATV the electrical system becomes live Do not try to affect changes to the E ATV such as removing the battery or repairing electrical components while the E ATV is activated Turn the E ATV off and remove the key before you attempt to access any of the electrical components Also the battery carries a significant electric charge and can injure people if not treated properly and with respect Accelerating and Decelerating The throttle is found on the right side hand grip on the handlebars Turn the grip forward away from you to accelerate To dece
8. take your e ATV to your Daymak dealer for servicing Bringing in your E ATV for Service Do not attempt to service the electronic or mechanical parts of your e ATV unless you are absolutely sure of what you are doing and have a solid understanding of electrical and mechanical equipment If your e ATV is not performing properly disconnect the circuit breaker and bring the e ATV to your local Daymak dealer Do not store the e ATV without disconnecting the circuit breaker Liability Daymak will not be held responsible for damage or injuries resulting from errors resulting from improperly serviced parts gt DAYMAK ATV Maintenance Cleaning Cleaning is extremely important this will ensure your e bike will serve you for a long time In the long run it will save you money and a lot of time waiting for the bike to be repaired You should clean your ATV weekly Do not use aggressive power jets or water sprays when washing the ATV and keep water off the battery as much as you can Clean gently but thoroughly and make sure that all the outer casing of the electric parts are dry and clean Remove any dirt debris sand mud grit grime that got caught on the bike and dry it off While cleaning it is a good opportunity to look closely for a worn loose cracked rust teared or damaged parts Buckled paint can also be a hint for some parts that need closer inspection Lubricating It is also recommended to lubricate the cables
9. the power has dropped significantly you should charge your e ATV Distance and Power Your battery has the capacity to carry you anywhere from 35 to 50 km before it must be re charged The ability of your battery to power your ATV depends on many variables These variables include the weight of the rider the prevailing wind resistance the rider s driving habits the presence of steep hills and inclines and other issues such as proper air pressure in the tires Saving Power If you are traveling long distances you can save a lot of electricity by using better driving habits Coasting When going downhill or over long flat road surfaces try using your e ATV s momentum and allow it to coast without drawing power from the motor e Stopping and Starting Try to avoid stop and go movements The motor draws more power when starting from a full stop Weight Remove unnecessary weight from the ATV This reduces the amount of power the motor must draw Air Pressure Make sure your tires have the proper air pressure Proper pressure reduces drag on the tires and radically increases the efficiency of any vehicle Head and Tail Lights Turn off the lights to conserve power if it is safe to do so The lights will reduce the distance you can travel by about 596 gt DAYMAK Charging your E ATV Charging your e ATV is a simple process You require the following The charger that came with your e ATV A 110V household
10. Sasquatch 1000W User Manual DDRYMAK About Daymak Daymak is one of Canada s largest Alternative Vehicle providers We design engineer man ufacture import and repair everything from recreational dirt bikes go karts and electric golf cars to alternative transportation solutions such as e bikes and gas scooters Our electric bicycles represent an energy efficient and eco friendly alternative for people who need to get around the city They greatly increase the practicality of bicycle transpor tation in urban centres Costing only a few cents to charge an e bike can make city life more convenient and much less expensive While there are many new Green technologies that are still in their infancy electric bicycles have been developing over the last 40 years or more E bike technology has been dramat ically refined since the introduction of the first custom conversion bicycles Today electric bicycles are a supremely reliable and affordable means of transportation Daymak is constantly developing new eco friendly alternative transportation strategies led by its own Research and Development department in Toronto Canada We are always improving our products Our innovative in house engineering and quality testing provide customers with many new kinds of reliable eco friendly vehicles designed to help change the lives of our customers and the world Daymak warranties services and stocks parts for everything it sells We support
11. affic laws This includes obeying stop signs checking carefully when turning and riding defensively An e ATV is a motorized vehicle even though it is classed as a ATV You must fol low the law e Stay Sober Never ride your ATV while intoxicated An e ATV is capable of trav eling faster than a normal ATV and you should always be in control of it Share the Road Be careful in mixed traffic When on ATV paths traveling near pedestrians or on recreational trails try to be polite and courteous to those using the paths with you E ATVs are new in most cities so other users of the roads and recreational paths may not know how to deal with e ATV riders Bear in mind that in a sense e ATV riders are ambassadors for this new method of transportation Items to Carry with the Electric ATV It is a good idea to carry the following items with you at all times when you ride your e ATV The charger to charge the ATV in case the battery power runs out A lock to secure your e ATV when you park it A helmet as required by safety laws gt DAYMAK Inspecting your Electric ATV Always inspect your e ATV before you ride it to make sure its safety features are oper ating properly Many accidents can be avoided with routine inspections Once you are comfortable with your e ATV you will be able to detect small changes in the way it feels If anything changes between uses make sure to have it properly examined Also be sure to
12. ain a charge and might have to be replaced sooner than would otherwise be necessary e Charge it Charge your battery immediately after riding it e Full Charge Do not allow the battery to run down completely and lie in storage without a charge This significantly reduces the battery s lifespan and may cause damage Keep it Charged When being stored charge the battery occasionally to make sure its power supply does not run down Charging it once every 21 days should be sufficient e Storage Conditions Store the battery on a flat cool dry surface Do not allow the battery temperature to drop below 10 degrees Celsius for extended periods of time Warning DO NOT place your Lead Acid battery on concrete Concrete drains the battery s power and will neutralize the lead acid Placing the battery on concrete for any length of time will likely result in the battery being drained of power and possibly losing its ability to store electricity O DAYMAK Cold Weather and your Battery Below 10 degrees Celsius the battery will not work as well as it would in warmer tempera tures While Lithium lon batteries perform better than Lead Acid batteries in temperature extremes both will experience reduced performance in cold temperatures Also repeatedly riding the e bike in cold temperatures may cause your battery to have to be replaced sooner Handling the Battery The battery contains large amounts of electrical power You must use
13. caution and respect when handling it Not following these instructions can result in serious injury Warning Follow these instructions closely Use care when handling your battery Always lift the battery with both hands and carry it with care Never drop the battery If the case is damaged the contents may leak out Never puncture or open the battery case The contents are dangerous and may cause injury Do not touch the contents of a leaking battery Seek help immediate ly Do not touch the two metal poles on the battery box at the same time This can cause a short circuit It could injure you or others and cause serious damage to the electrical systems in the e bike Your battery contains significant amounts of electrical power Do not handle your battery if either you or the battery are wet Water is an ex cellent conductor of electricity You may experience an electrical shock and you may be injured gt DAYMAK Replacement and Disposal After approximately 300 charges a lead acid battery will need to be replaced A lithium ion battery will last approximately 1500 charges When the battery has to be replaced you will notice that your battery cannot carry as much of a charge as it could initially Contact your local Daymak dealer to purchase a new battery When replacing your battery dispose of it at a proper municipal battery recycling facility If none is available please contact your local Daymak
14. d more patience The front wheel is easier to service when changing a flat tire than the rear wheel as the rear wheel is connected to the hub motor and other mechanical parts Unless you are very familiar with the mechanical components of the rear motor attempt ing to change a flat rear tire may cause serious problems Please contact your Daymak dealer for specific instructions on how to remove your wheel and tires safely and how to replace the tubes It may be easier and safer to have the tubes replaced by your Daymak dealer gt DAYMAK The Brakes The drum brakes on your Smart ATV allow you to stop and are a critical safety feature Make sure you test them regularly Take the e ATV to your Daymak dealer if the brakes appear to be losing their stopping power or feel looser than they were previously The brakes on your e ATV may require servicing from time to time The brake pads will need to be replaced as they wear down usually after about a year to a year and a half or so depending on how the e ATV is ridden Also the brake cables may have to be adjusted for tension You can only service the brakes yourself if you have extensive experience servicing drum brakes Please do not attempt to service the drum brakes if you are not absolutely sure how to do it Adjusting the Brake Cable Tension From time to time you may need to adjust the brake cable tension to loosen or tighten the drum brakes On your drum brakes a
15. e Controller Daymak pioneered the development of intelligent component control in e ATVs The D Drive technology developed by Daymak is the brain of your e ATV It allows your e ATV to achieve faster acceleration to climb steeper hills and to save energy In future it will allow for other ways of recharging your e ATV s batteries such as by using solar or wind power The electronic controller is located under the seat assembly This controller efficiently regulates the speed and electronic functions of the ATV It allows for stepless speed adjustment shuts off the motor when the brakes are activated has low voltage protection and has fuses to prevent excess current from damaging the e ATV s systems The Governor A key component of the controller is the Governor The Governor regulates the speed of the e ATV It pre vents the motor from assisting riders when the e ATV s speed surpasses 32 km per hour The governor s primary function is to make sure that the motor functions efficiently If the governor is not functioning the mileage of the e ATV will be dramatically reduced and its performance will suffer Disabling the governor voids the warranty and may damage your controller This speed limitation to 32 km per hour is required by government regulations Traveling faster than 32 km per hour through motor power alone is illegal in Canada and could result in serious fines or penalties unless your vehicle is insured for liability
16. etc A clean lubricated e ATV tends to be faster smoother and quieter It s like having a little extra push for free Apply the lubricant to the different parts and let it sit a few minutes and then wipe off the excess lubricant with a rag After a while clean the different parts with a degreaser to remove any excess dirt that has been collected Weather Don t leave the ATV out in the rain or snow Store it somewhere dry and out of direct sunlight Overheating the batteries for example can cause problems Do not open up casings chargers etc as you are unlikely to be able to reseal them ef fectively afterward making them more susceptible to water damage and other extreme weather conditions Batteries should be removed from the ATV if not used and charged once a month regard less of usage O DAYMAK 23 Schedule The frequency of maintenance depends on how much you ride and under which conditions Recreational riders needs far less maintenance then off road riders The harder you ride the more you have to take care of your ATV if you want it to last There are various time intervals for proper maintenance Quick maintenance should be done before amp after every ride Time after purchase Action Suggested Check tire p ressure check brakes t hat they w ork check lights c heck bolts makes ure everything i s tight c heck battery gauge D o notride the ebike unless everything is functional and proper Every
17. insert the key into the lock on the left side of the e ATV just below the seat Turn it all the way to the right The seat will snap open and pop up To close the seat trunk make sure that there is nothing blocking the locking mechanism such as items you have placed in the storage compartment and push the seat down with force You will hear a click sound when it is properly closed Parking and Locking your E ATV When you want to park your e ATV for a short time either when you have reached your destination or are at home follow these steps 1 Stop the e ATV and position it as you want it 2 Get off the e ATV making sure to keep it balanced 3 Stand to the side and slightly to the rear of the e ATV 4 Lock your e ATV to a ATV locking post or other secure object through the rear wheel frame or one of the metal frame components Warning Do not let your e ATV drop or fall The exterior may be damaged The fall may damage oth er components inside the e ATV as well Your e ATV may or may not have a seat compartment or rear storage gt DAYMAK Maximum Load Do not exceed the maximum load capabilities of your e ATV You can find the exact load ing capacity listed in the technical specifications in this guide If you exceed the maximum load the performance of the ATV will suffer Exceeding the maximum load of your e ATV could cause damage to the shocks to the mechanism and ultimately even to the frame It
18. lerate release the grip turn it towards you Don t over rotate the accelerator as this could damage the battery and electrical components Warning Do not activate the accelerator until you are seated on the ATV and are ready to accelerate The e ATV can easily escape from your control possibly injuring you or others and the e ATV may be damaged by being dropped gt DAYMAK Stopping Your e ATV has two sets of brakes at the front and at the rear The levers attached to the handlebars on the left and right activate the brakes Pull the levers toward you to activate the brakes You can use both brakes to come to a stop more quickly or you can use one of the brakes to come to a gentle stop depending on your riding needs at the moment When the brakes are activated the power to the engine is automatically turned off until you release the brakes This allows you to stop safely Safety Tips When you are traveling in wet weather water may cause your brakes to function less efficiently because it reduces friction between the brake pads and the wheels Take care to slow down and give yourself more room to stop or slow if necessary e Itis a good idea to have your brakes and brake pads checked regularly The brake pads will eventually wear down through friction and after significant use will have to be replaced Signalling The Horn The e ATV has a horn The horn button is on the left handlebar Simply press it to ac
19. omponents Alteration of these components voids the warranty Tire Pressure Maintain the air pressure in your tires at the appropriate level If the air pressure is too low your e ATV s performance will suffer and it will become damaged more easily Cold weather and lower temperatures will cause the air pressure in your tires to drop and warmer weather will cause it to increase even if there are no leaks in the tire tube To re place the air in your tires follow this procedure 1 Identify the required pressure by examining the text along the side of the tire rim This text should indicate the recommended pressure for your tire Locate the air valve on the inner surface of the tire rim Remove the valve cap and place in a secure location Place the nozzle end of an air pump hand power or mechanical over the valve Pump up the air in the tire being careful not to let the pressure go above the level prescribed on the side of the tire wall Remove the pump nozzle from the air valve without allowing much air to escape from the tire 7 Replace the valve cap on the air valve UAWN a Maintaining the proper air pressure will allow you to travel much further on a single charge because the motor will not have to work as hard to move the e ATV Replacing Flat Tires Replacing flat tire tubes is a more complicated and labour intensive process with e ATVs than it is with regular ATVs It requires proper tools more skill an
20. our prod ucts Please feel free to visit our website You ll find the latest in cool transportation solutions support for the products you ve purchased and contact information gt DAYMAK Table of Contents NRO UC EID nenne einsehen 4 Part Diatjl alis usas ia oot aad GINE nn iU bn ir eds qais bou Re RE ER S GN Oc DOE 5 Riding Irist Ue HOS nee ee 6 Ope r ting INSTMIELIONS tr 10 Huius T T LAPEER EKE EE iNi 12 Technical Data nn anne 17 Maintenance and Troubleshooting usan erp ee 20 O DAYMAK Introduction E ATV Riding an electric ATV is a great way to hop around town conveniently and cheaply E ATVs represent a natural progression in the development of urban transportation Using only small amounts of electricity e ATVs have the potential to radically reduce the amount of pollution in our cities As well they are very quiet so they do not add tothe high levels of noise pollution which we often take for granted They are easy and usually free to park They are unobtrusive and highly practical additions to the urban landscape E ATVs are also inexpensive They currently require no registration no insurance no li cence and do not incur parking charges As well compared to internal combustion en gines the engines in electric vehicles have fewer moving parts and require far less main tenance Your Daymak e ATV is the result of Daymak s years of experience the
21. s such as drops from a height of 15 cm or more can cause serious damage to your shock absorbers Replacing them is a complex and time con suming task so do be careful when dropping from larger heights O DAYMAK Basic Statistics Dimensions Weight Loading Capacity Speed and Mileage Wheel Size 19x7 8 Seat Height 75cm 29 35 kg without battery 50 kg with battery Standard 75 kg Maximum 150 kg Max Speed 32 km h Max Mileage 50 km Electrical System Statistics Motor Statistics Rated Power 1000W Voltage 48V Rated rolled speed 200 RPM Working efficiency 70 8096 Torque 32 55 Nm Max Climbing Angle 12 15 Degrees Controller Statistics Input voltage 48V Charger Statistics Charger Input AC 100 240V Standard Input voltage 110V 10 Output DC 48V BM online Charger output voltage 43 8 10 50Hz Power Rated 800W Charge Time 6 12 hours Battery Statistics 4 Batteries Each Type Sealed Lead Acid Battery Rated Voltage 48V Rated Power 20AH Battery Life 300 charges Number 4 battery units in series Standard Capacity 12V x 20AH Rated Total Capacity 500Wh O DAYMAK 20 Maintenance and Troubleshooting This section outlines problems you may have and solutions you may be able to use Many of the parts in this product are not user serviceable and should be repaired by trained professionals This is especially true of the electrical systems and the mechanical c
22. small wing nut rides up and down a threaded bolt moving the brake cable and tightening or loosening the brake pads Just outside the casing near the drum brake the brake cable joins the drum brake A small wing nut allows you to adjust the tension 1 Locate the wing nut on the drum brake 2 To tighten the brakes turn the wing nut clockwise 3 To loosen the brakes turn the wing nut counter clockwise 4 Adjust the tension until the drum brakes are tight enough to provide for proper safety but are loose enough to allow the wheel to move freely when the brake is not engaged Warning Your brakes are a critical safety feature Do not excessively loosen the drum brakes If you do not keep them sufficiently tight your drum brakes will fail and your e ATV will not be able to stop properly gt DAYMAK 21 22 The Motor Do not service the motor yourself Bring the e ATV to your Daymak dealer for service The motor in your e ATV is a highly complex and fine tuned mechanism Repairing it requires significant expertise We suggest maintenance every 100 running hours or so Shock Absorbers and Comfort If your riding experience feels bumpier than usual and you suspect that your shock ab sorbers are experiencing difficulties check the air pressure in your tires If the air pressure is too low this may be the reason you feel less comfortable It may have nothing to do with your shock absorbers If the problem persists
23. time before you ride The 60 second check Completely clean the bike including the dust on the motor and underthe seat Check for any abnormal wear and tear or alignment problems 30 days every month Inspect frame and fork for paint cracks or bulges that 90 days may indicate f rame or part damage p ay p articular every 3 months attention to all frame joints Check wear and tear on tires Check range of battery Inspect all components oft he ebike Check that 180 days connections are nice and tight Look inside where you every 6 months controller is and clean in detail Check that all plugs Go over every bolt and nut in your ebike Bring ebike f or c omplete t une up Varying ont he ebike t he ebike s hop s hould completea b attery 360 days discharge tiresshould be changed depending on every 12 months wear and tear All connections should be checked for rust andl ooseness A llc omponents should be checked including charger ignition and gauges gt DAYMAK
24. tivate the horn Turning Signal Lights Your e ATV has turn signal lights The turn signal activator is on the left handlebar Push it left or right to activate it to indicate that you are turning in the appropriate direction and press the middle of the button to turn it off The turn signals also emit a noise to ensure that everyone knows you are turning This turn signal cannot be disabled without also disabling the visual signal Lights The headlight and taillight are useful features when you are riding at night or in dark areas They radically improve your safety in mixed traffic The switch is located on the left handle bar The lights on your e ATV consume some electricity Keeping them on may reduce the maximum distance you can travel on one charge by about 5 96 gt DAYMAK Riding in Wet Weather Your e ATV is designed to function in wet conditions such as when it is raining However because the motor is on the rear wheel it is easy to slip when moving at high speeds If it is very wet be sure to avoid high speeds When you are traveling in wet weather water may cause your brakes to function less ef ficiently because it reduces friction between the brake pads and the wheels Take care to slow down and give yourself more room to stop or slow if necessary The Motor and Water Your e ATV is not designed to be immersed in water Always ensure that the water level does not go above the middle of the tire to prevent
25. water from getting inside the motor Water in the motor can cause short circuits and may damage the electrical systems in your e ATV Riding in Cold Weather Your e ATV is designed to operate year round However in very cold conditions or when there is a lot of snow or slush on the ground it is possible for the motor in the e ATV to get wet or for the brakes to function less efficiently just as can happen in wet weather Below 10 degrees Celsius the battery will not work as well as it would in warmer temperatures While Lithium lon batteries perform better than Lead Acid batteries in temperature ex tremes both will experience reduced performance in cold temperatures Also riding the e ATV in cold temperatures may require you to replace the battery sooner rather than later gt DAYMAK Operating Instructions Using the Rear Storage Compartment The rear storage compartment is opened using the key provided to you when you pur chased your e ATV Insert the key and turn it to the right to open the compartment Close the case and turn the key in the opposite direction to lock the compartment again You can use this compartment to store the charger and associated cables so you can recharge your e ATV if it runs out of power It can also hold a locking mechanism such a u lock for added security when parking your e ATV The space provided is perfectly suited for these purposes Opening the Seat Trunk To open the seat trunk
Download Pdf Manuals
Related Search