Home

5GHz Outdoor Router User Manual

1. VPN is the abbreviation of Virtual Private Network It is designed for creating point to point private link via shared or public network 5 28 What is IPSEC IPSEC is the abbreviation of IP Security It is used to transferring data securely under VPN 5 29 What is WLAN Block Relay between Clients An Infrastructure Basic Service Set is a BSS with a component called an Access Point AP The access point provides a local relay function for the BSS All stations in the BSS communicate with the access point and no longer communicate directly All frames are relayed between stations by the access point This local relay function effectively doubles the range of the IBSS 5 30 What is WMM WMM is based on a subset of the IEEE 802 1 le WLAN QoS draft standard WMM adds prioritized capabilities to Wi Fi networks and optimizes their performance when multiple concurring applications each with different latency and throughput requirements compete for network resources By using WMM end user satisfaction is maintained in a wider variety of environments and traffic conditions WMM makes it possible for home network users and enterprise network managers to decide which data streams are most important and assign them a higher traffic priority 5 31 What is WLAN ACK TIMEOUT ACK frame has to receive ACK timeout frame If remote does not receive in specified period it will be retransmitted V3 0 0 WO Loopcomm 5 32 What is Modulatio
2. 2040 security Mode WPA PSE w setup Wizard AP Client WWOS 4P or WDS step 2 Configure Wireless settings wireless Band SOZ LIB GYN wireless Mode AP Ww Frequency Channel AutoSelect w Current Channel 1 Network Name SSID ol lln Router Channel Bandwidth Cop 27040 Security Mode WP AZ PSK When you finish these settings then click Apply button to save Choose either Client or WDS then click Next button to step 3 V3 0 0 W Loopcomm Step 3 a Configure AP Client Mode Settings setup Wizard This mode is for bridge setting The setup Wizard will guide you to configure the mode to setting AP AP Client WDS AP or WDS step 3 Configure AP Client Mode Settings AP Client parameters zal SOZ ln Router Security Mode OPEN Encryption Type NONE b Configure WDS Mode Settings Setup Wizard This mode is for bridge setting The Setup Wizard will guide you to configure the mode to setting AP AP Client WDS AF or WDS Step 3 Configure WDS Mode Settings poe E E owe poe E E E PONE e E Ooo Ba SE V3 0 0 W Loopcomm 4 3 1 2 Gateway Mode This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your ISP Internet Service Provider setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your SP ilnternet Servi
3. 2040 Security Mode SHAREDWEP When you finish these settings then click Next button to jump at Step4 Frequency Channel V3 0 0 W Loopcomm WPA PSK setup Wizard This mode is use wireless to connected APS The Setup Wizard will guide you to configure the wireless how to connect any APS and setting WAN mode to connected internet step 3 Configure Wireless Settings wireless Band 202 LLEGAN EE Current Channel 1 Network Name SSID 804 1 ln Router Channe Bandyyvidth Oo soo Security Mode WPA PSK i poa Loo ee When you finish these settings then click Next button to jump at Step4 Wireless Settings V3 0 0 WO Loopcomm WPA2 PSK setup Wizard This mode is use wireless to connected AFS The setup Wizard will guide you to configure the wireless how to connect any APS and setting WAN mode to connected internet step 3 Configure Wireless Settings Wireless Settings wireless Band 207 LlIB G N T Current Channel 1 Network Name SSID SOZ ln Router nanne Bandwidth Con soo security Mode WPAC PSK Item Description Wireless Band Click to select wireless band from pull down menu Frequency Channel Select the wireless communication frequency channel from pull down menu Network Name SSID It is the wireless network name The SSID can be 32 bytes long Channel Bandwidth Select the operating channel width 20 MHz or 20 40 MHz Security Mode
4. Status Dizable Server IP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection User can use embedded PPTP client supported by this router to make a VPN connection If you select the PPTP support on WAN interface fill in the IP address for it Fill in the user name and password to login the PPTP server Fill in the user name and password to login the PPTP server Address Mode Static To configure the IP address information by manually please fill in the related setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Operation Mode Keep Alive Keep the PPTP connection all the time Please also configure the Redial Period field On Demand Please configure the Idle Time field When time is up the PPTP connection will disconnect The connection will re connect when any outgoing packet arise Manual Let user connect the PPTP connection manually MAC Clone Take NIC MAC address of PC on LAN side as the MAC address of WAN interface V3 0 0 WO Loopcomm 4 3 3 2 LAN Local Area Network LAN Settings You may enablefdisable networking functions and configure their parameters as your wish LA
5. etc v Building Materials metal door aluminum studs v Electrical devices microwaves monitors and electrical motors Solutions to overcome the interferences v Minimizing the number of walls and ceilings v Position the WLAN antenna for best reception v Keep WLAN devices away from other electrical devices eg microwaves monitors electric motors etc v Add additional WLAN Access Points if necessary 5 8 What are the Open System and Shared Key authentications IEEE 802 11 supports two subtypes of network authentication services open system and shared key Under open system authentication any wireless station can request authentication The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station The receiving station then returns a frame that indicates whether it recognizes the sending station Under shared key authentication each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802 11 wireless network communications channel 5 9 What is WEP An option of IEEE 802 11 function is that offers frame transmission privacy similar to a wired network The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers WEP relies on a secret key that is shar
6. Protocol TCP amp UDP Comment The maximum rule count is 32 Virtual Server Select Enable or Disable the Virtual Server function IP Address To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall fill in the IP address Public Port To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall fill in the public port Private Port To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall fill in the private port Protocol Specify protocol TCP amp UDP TCP or UDP Comment Make a comment for the virtual server policy V3 0 0 Q Loopcomm 4 3 5 3 DMZ DMZ Settings You may setup a De militarized Zone DMZ to separate internal network and Internet DMZ Settings DMZ Settings Disable DMZ Settings Enable or Disable the DMZ function DMZ IP Address To support DMZ in your firewall design fill in the IP address of DMZ host that can be access from the WAN interface V3 0 0 Q Loopcomm 4 3 5 4 System Security system Security Settings You may configure the system firewall to protect AP Router itself from attac king Remote management Remote management via WWAN Ping form WAN Filter Ping form WWAN Filter Stateful Packet Inspection SPI SPI Firewall A
7. Please select the security mode related wireless data encryption WEP When you select WEP please input 5 13 ASCII 10 or 26 HEX characters for WEP Key Pre Shared Key WPA PSK WPA2 PSK When WPA WPA2 Pre shared key encryption is selected please fill in the Pre shared key The format can be passphrase or Hex 64 characters When you finish these settings then click Apply button to save V3 0 0 W Loopcomm Step 4 Configure AP Client setting setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless how to connect any APs and setting WAN mode to connected internet step 4 Configure AP Client setting AP Client AP Client parameters _ Encryption Toe Type NONE NONES SCAN APs SE Authentication Wireless Mode nn V3 0 0 W Loopcomm 4 3 2 Operation Mode a Bridge Operation Mode Configuration You may configure the operation mode suitable for you environment In this mode all ethernet ports and wireless interface are bridged together and NAT function is disabled All the WWAN related function and firewall are not supported Bridge In this mode the device is supposed to connect to internet via ADSL Cable Modem The NAT is oO Gateway enabled and PCs in LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP client PPTP client ATF client or
8. can be passphrase or Hex 64 characters V3 0 0 W Loopcomm OPEN WEP setup Wizard This made is for bridge setting The Setup Wizard will guide you to configure the mode to setting AP AP Client WOS A4P or WDS step 2 Configure Wireless settings wireless Band B02 LIB G N wireless Mode Mode Se Ca Frequency Channel Autoelect ect Current Channel 1 Network Name SSD Name SSID SU lin Router Channel Bandyvidth Oan o040 Security Mode OFEN WEP SHAREDWEP Setup Wizard This mode is for bridge setting The setup Wizard will guide you to configure the mode to setting AP AP Client WWOS 4P or WDS step 2 Configure Wireless settings me Band nr LLB GIN N b wireless Mode Mode Frequency Channel AutoSelect wl Current P Network Name SSID Name SSID Bolink lin Router channel e Bandvyvidth Oo 2040 Security Mode SHARED WEP V3 0 0 W Loopcomm WPA PSK setup Wizard This made is for bridge setting The Setup Wizard will guide you to configure the mode to setting AP WPA2 PSK This mode is for bridge setting The Setup Wizard will guide you to configure the mode to setting AP AP Client WOS 4P or WDS Step 2 Configure Wireless settings wireless Bang SUA LIB G N wireless Made AP Frequency Channel Autoselect Current Channel 1 Network Name SSID SO2 l ln Router Channel Bandwidth Oog
9. for it Fill in the user name and password to login the L2TP server Fill in the user name and password to login the L2TP server Address Mode Static To configure the IP address information by manually please fill in the related setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Operation Mode Keep Alive Keep the L2TP connection all the time Please also configure the Redial Period field On Demand Please configure the Idle Time field When time is up the L2TP connection will disconnect The connection will re connect when any outgoing packet arise Manual Let user connect the L2TP connection manually MAC Clone Take NIC MAC address of PC on LAN side as the MAC address of WAN interface V3 0 0 Q Loopcomm e PPTP Wide Area Network MAN Settings Vou may choose different connection type suitable for your environment Besides you may alsa configure parameters according to the selected connection type WAN Connection Type PPTP i we PPTP Mode Server iF es User Name LO Password DO CSsC Address Mode ro tat wt iP address LZ Subnet mask C Default Gateway Operation Mode Keep Alive Made Redial Period Ssencoands
10. g client Mode transmissions Beacon Interval Beacons are the packets sending by Access point to synchronize the wireless network The beacon interval is the time interval between beacons sending by this unit in AP or AP WDS operation The default and recommended beacon interval is 100 milliseconds Data Beacon This is the Delivery Traffic Indication Map It is used to alert the clients that Rate DTM multicast and broadcast packets buffered at the AP will be transmitted immediately after the transmission of this beacon frame You can change the value from 1 to 255 The AP will check the buffered data according to this value For example selecting 1 means to check the buffered data at every beacon Fragment The fragmentation threshold determines the size at which packets are Threshold fragmented sent as several pieces instead of as one block Use a low setting in areas where communication is poor or where there is a great deal of radio interference This function will help you to improve the network performance V3 0 0 WO Loopcomm RTS Threshold The RTS threshold determines the packet size at which the radio issues a request to send RTS before sending the packet A low RTS Threshold setting can be useful in areas where many client devices are associating with the device or in areas where the clients are far apart and can detect only the device and not each other You can enter a setting ranging from 0
11. in the default gateway for WAN interface out going data packets Operation Mode Keep Alive Keep the PPTP connection all the time Please also configure the Redial Period field Manual Let user connect the PPTP connection manually When you finish these settings then click Next button to jump at Step3 V3 0 0 WO Loopcomm Step 3 configure Wireless Settings There are five options Disable WEP WPA PSK WPA2 PSK for Wireless security connection setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your lsPilnternet Service Provider step 3 Configure Wireless Settings Wireless Settings wireless Band oU4 LIB GIN Frequency Channel AutoSelect _ CO Channel 1 Network Name SSID oO l1n_ Router Channe Randvvidth Oon onan Securty Mede Disable CIFEN WEF HARED WEP WPA2 PSE Item Description Wireless Band Click to select wireless band from pull down menu Frequency Channel Select the wireless communication frequency channel from pull down menu Network Name SSID J It is the wireless network name The SSID can be 32 bytes long Channel Bandwidth Select the operating channel width 20 MHz or 20 40 MHz Security Mode Please select the security mode related wireless data encryption WEP When you select WEP please input 5 13 ASCII 10 or 26 HEX characters for WEP Key Pre Shared Key WPA PSK WPA2 PSK Whe
12. nennen ereen 81 5 29 What is DDNS eetset n E AE AE EIEE EAN E 82 5 20 What is NIP Chenf oenen eeen E 82 Deze WS VENS E E AAE A N AT 82 SO Whats IERSE ae N E E 82 5 29 What is WLAN Block Relay between Clients 82 OW DAIS IY DIN eenst 82 5 31 What is WLAN ACK TIMEOUT eeccccccccceceeseeeeeceeeeeenaas 82 5 32 What is Modulation Coding Scheme MCS cc ccceecceecceeeeeeees 83 V3 0 0 W Loopcomm 5 33 What is Frame Aggregation 00 0 0 cccccccccccccccaeesseeeecceeeeeaaeeeseeeeeeeeeaaas 83 5 34 What is Guard Intervals GD ennen eenen 83 V3 0 0 Ww Loopcomm 1 Terminology V3 0 0 Q Loopcomm TKIP Temporal Key Integrity Protocol UPNP Universal Plug and Play Virtual Private Network V3 0 0 Q Loopcomm 2 Introduction The Outdoor Router is an affordable IEEE 802 11b g n specifications of Outdoor Router solution setting SOHO and enterprise standard for high performance secure manageable and reliable WLAN This document describes the steps required for the initial IP address assign and other configuration of the outdoor router The description includes the implementation of the above steps 2 1 Package Content The package of the WLAN Broadband Router includes the following items v Outdoor Router Y DC 12V Power Adapter Y Documentation CD Y POE Injector v Tie 2 2 Product Features gt Compatible with IEEE 802 11n Specifications provides wirel
13. static IP In this mode all ethernet ports are bridged together and the wireless client will connect to ISP access point The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN You must set the wireless to client mode first and connect to the ISP AP in site Surey page Wireless ISP The Bridge mode allows that all Ethernet and wireless interfaces are bridged into a single bridge interface b Gateway Operation Mode Configuration You may configure the operation mode suitable for you environment In this mode all ethernet ports and wireless interface are bridged together and NAT function is disabled All the WAN related function and firewall are not supported Bridge In this mode the device is supposed to connect to internet via ADSL Cable Modem The NAT is el Gateway enabled and PCs in LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP client PPTP client TF client or static IP In this mode all ethernet ports are bridged together and the wireless client will connect to ISP access point The MAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN You must set the wireless to client mode first and connect to the ISP AP in site Suvey page O Wireless ISP The Gateway mode allows that the first Ethernet port is treated as WAN port and the Ethernet port
14. there is connection the WPS Summary will show related information and status Here shows the AP s PIN code Personal Identification Number that the enrollee should enter the registrar s PIN code to make a connection Click Generate button to generate a new AP PIN code WPS mode Select WPS mode PIN Personal Identification Number PBC Push Button Communication Input enrollee s PIN code to AP registrar V3 0 0 WO Loopcomm 4 3 5 Firewall 4 3 5 1 MAC IP Port Filtering MAC IP Port Filtering Settings You may setup firewall rules to protect your network from virus worm and malicious activity on the Internet Basic Settings MACiIPIPor Filtering MAC IP Port Select Enable or Disable the MAC IP Port Filtering function Filtering Source MAC address Lo Dest IF Address sd Source IP Address sd Protocol Hone Dest Pon Range C T Source Port Range CH commen _ ti TCS The maximum rule count is 32 Source MAC m Fill in the MAC address of source NIC to restrict data transmission address Dest IP Address Fill in the IP address of destination to restrict data transmission Source IP Address Fill in the IP address of source to restrict data transmission Protocol Select the protocol that you want to restrict There are four options None TCP UDP and ICMP Dest Port Range Fill in the start port and end port number of destination to restrict data transmission Source Po
15. to 2347 bytes TX Power The default TX power is 100 In case of shortening the distance and the coverage of the wireless network input a smaller value to reduce the radio transmission power For example input 80 to apply 80 Tx power Short Preamble Default Disable It is a performance parameter for 802 11 b g mode and not supported by some of very early stage of 802 11b station cards If there is no such kind of stations associated to this AP you can enable this function Short Slot It is used to shorten the communication time between this AP and station TX Burst The device will try to send a serial of packages with single ACK reply from the clients Enable this function to apply it Country Code Select the country code for wireless from pull down menu V3 0 0 W Loopcomm 4 3 4 3 Security a Disable Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring Security Wireless Security Mode Disable Access Policy If you set Security Mode to Disable the wireless data transmission will not include encryption to prevent from unauthorized access and monitoring V3 0 0 Q Loopcomm b OPEN WEP SHARED WEP Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from Unauthorized access and monitoring Security Wireless Security Mode OFEN WEP iw Wire Equivalenc
16. N Setup MAC Address 8C 92 36 00 66 F 8 ip Address Subnet Mask DHCP Type Lease Time Boo 802 10 Spanning Tree LTD lowe Proxy Disable uPnP Router Advertisement Disable w PPPoE Relay Disable DNS Proxy Disable ar Take NIC MAC address of PC on LAN side as the MAC address of WAN MAC Address interface IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface DHCP Type Disable Disable DHCP server on LAN side Server Enable DHCP server on LAN side Lease Time Fill in the lease time of DHCP server function LLTD Select enable or disable the Link Layer Topology Discover function from pull down menu IGMP Proxy Select enable or disable the IGMP proxy function from pull down menu UPNP Select enable or disable the UPnP protocol from pull down menu DNS Proxy Select enable or disable the DNS Proxy function from pull down menu V3 0 0 WO Loopcomm 4 3 3 3 VPN Pass Through VPN Passthrough WPN passthrought configurations including LATA IPSec and PPTP passthrough VPN Pass Through LTF Passthraugh Enable IPSec Passtrough Enable PPTP Passthrough Enable v i Item Description L2TP Passthrough Select enable or disable the L2TP pass through function from pull down menu IPSec Passthrough Select enable or disable the IPSec pass through function from pull down menu PPTP Passthrough Select enable or disable the PPTP pass through function f
17. Subnet Mask Dn Default Gateway fo Prima DAS Server fo secondary DAS Server DO Primary DNS Fill in the IP address of Domain Name Server 1 Server Secondary DNS Fill in the IP address of Domain Name Server 2 Server When you finish these settings then click Next button to jump at Step3 V3 0 0 Q Loopcomm c PPPOE ADSL If you select PPPOE please fill in these fields on next page setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your lSP nternet Service Provider step 2 Configure Internet Connection clita Connection PPPOE ADEL v Type PPPoE Mode user Name Password very Passwor _ Operation Mode Keep Alive Mode Redial Period ED senconds On demand Made Idle Time Een minutes User Name If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Password If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Verify Password Fill in the password again for verification Operation Mode Keep Alive Keep the PPPoE connection all the time Please also configure the Redial Period field On Demand Please configure the Idle Time field When time is up the PPPoE connection will disconnect The connection will re connect when any outgoing packet arise Manual Let user connect the PPPoE conne
18. Timeout E Access Policy Pony Psae WPA Cipher Suite Select TKIP or AES for WPA algorithms Key Renewal Please fill in a number for Group Key Renewal interval time Interval IP Address Enter the RADIUS Server s IP Address provided by your ISP Enter the RADIUS Server s port number provided by your ISP The Default is 1812 Shared Secret Enter the password that the Wireless Router shares with the RADIUS Server Session Timeout Session timeout interval is for 802 1x re authentication setting Set to zero to disable 802 1x re authentication service for each session Session timeout interval unit is second and must be larger than 60 Idle Timeout Enter the idle timeout in the column V3 0 0 WO Loopcomm e 802 1X Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from Unauthorized access and monitoring Security Mode BL iw 02 1x WEP WEP Disabled Enabled G Address fo Port shared Secret E session Timeout fo idie Timeout m Access Policy Policy Aad a station Mac E arry WEP Select Disable or Enable For WEP IP Address Enter the RADIUS Server s IP Address provided by your ISP Port Enter the RADIUS Server s port number provided by your ISP The Default is 1812 Shared Secret Enter the password that the Wireless Router shares with the RADIUS Server Session Timeout Session timeout interval is for 802 1x re authent
19. WO Loopcomm 2 4GHz Outdoor Router User Manual 2014 V3 0 0 Q Loopcomm Table of Contents de F111 100 oaea AEEA NEE ENANA 5 CD PAV OR ECU U ENE EPTO TATT A AEI AE O 7 2 1 Package Content annae eeeenenennnnnnererervensnnnnnnrrseervevens 7 2 2 Prod ct WC AG CS coression r a a e ni 7 2 3 Rear Panel Description aa eneneenennnereereeenenennnrreeervenens 8 2 3 Fro nt Panel Description sissscecstontstandaeseceutesciasienaccusiantessoiariecateateceesiseaseaieuntes 9 3 Hardware Installation snnnannnnneerrrenneene eee veenenenennnnnnnnens 10 3 1 Appearance and Interface Introduction aaneen 10 3 2 Hardware Installation Steps nanne nnen neen eeeenenenn 12 4 Software Configuration a ssc sosatongasseed spansausene conor a deaatenasssuntscsasareecncentonscoacovaasian 14 4 1 Prepare your PC to configure the WLAN Broadband Router 15 4 2 Connect to the WLAN Broadband Router 16 4 3 Management and configuration on the Outdoor Router 16 A A ose says thea tance she tsea A ocieeiesaaeseadeaataseateess 16 4 3 1 1 Bridge Mode en eeeenneeeeeeneenen 16 4 3 1 2 Gateway Mode anneer nennen 21 dol WISP MOE nnen metende 30 4 32 Operation Mod tsnevennenserdhereeverneetneatsinevansenterebbebncvantausbeedennanendsnie 41 4 3 3 Internet Settings onsnensee nee neenenen
20. and the wireless interface are bridged together and are treated as LAN ports V3 0 0 W Loopcomm c Wireless ISP Operation Mode Configuration You may configure the operation mode suitable for you environment In this mode all ethernet ports and wireless interface are bridged together and MAT function is disabled All the WAN related function and firewall are not supported Bridge In this made the device is supposed to connect to internet via ADSL Cable Modem The NAT is Gateway enabled and PCs in LAN ports share the same IP to ISP through WAN part The connection type can be setup in WWAN page by using PPPOE DHCP client PPTP client ATF client or static IP In this made all ethernet ports are bridged together and the wireless client will connect to SP access point The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAM You must set the wireless to client mode first and connect to the ISP AP in oite Sunvey page O Wireless ISP The Wireless ISP mode allows that the wireless interface is treated as WAN port and the Ethernet ports are LAN ports V3 0 0 WO Loopcomm 4 3 3 Internet Settings 4 3 3 1 WAN a STATIC Wide Area Network WAN Settings You may choose different connection type suitable for your environment Besides you may alsa configure parameters according to the selected connection type WAN Connection Type ee TATIC fined IP iw adres
21. annel from pull down menu Network Name SSID ff It is the wireless network name The SSID can be 32 bytes long Channel Bandwidth Select the operating channel width 20 MHz or 20 40 MHz Security Mode Please select the security mode related wireless data encryption WEP When you select WEP please input 5 13 ASCID 10 or 26 HEX characters for WEP Key Pre Shared Key WPA PSK WPA2 PSK When WPA WPA2 Pre shared key encryption is selected please fill in the Pre shared key The format can be passphrase or Hex 64 characters V3 0 0 W Loopeomm OPEN WEP setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless how ta connect any APs and setting WAN mode to connected internet step 3 Configure Wireless Settings wireless Bana Band SOe LIB GIN Frequency Channel AutoSelect wl Current Channel 1 Network Name SSID Name SSID SU lin Router channe Band vyvicth Oo omvang security Mode OPENWEE When you finish these settings then click Next button to jump at Step4 SHAREDWEP setup Wizard This mode is use wireless to connected APs The setup Wizard will guide you to configure the wireless how to connect any APs and setting WAN mode to connected internet step 3 Configure Wireless Settings wireless Band 02 11 E G M AutoSelect Current Channel 1 Network Name SSID SOZ l ln Router Channel Bandwidth onp
22. ated setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Operation Mode Keep Alive Keep the L2TP connection all the time Please also configure the Redial Period field Manual Let user connect the L2TP connection manually When you finish these settings then click Next button to jump at Step3 V3 0 0 WO Loopcomm e PPTP If you select PPTP please fill in these fields on next page setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless how to connect any APs and setting WAM mode ta connected internet Step 2 Configure Internet Connection WAN Connection PETE Type ECT EEN En Operation Mode Keep Alive Mode Redial Period senconds et Back JL Net JL Cm PPTP Server IP Allow user to make a tunnel with remote site directly to secure the data Address transmission among the connection User can use embedded PPTP client supported by this router to make a VPN connection If you select the PPTP support on WAN interface fill in the IP address for it Fill in the user name and password to login the PPTP server Password Fill in the user name and password to login the PPTP ser
23. bridge or repeater service 5 22 What is Universal Plug and Play uPNP UPnP is an open networking architecture that consists of services devices and control points The ultimate goal is to allow data communication among all UPnP devices regardless of media operating system programming language and wired wireless connection 5 23 What is Maximum Transmission Unit MTU Size Maximum Transmission Unit MTU indicates the network stack of any packet is larger than this value will be fragmented before the transmission During the PPP negotiation the peer of the PPP connection will indicate its MRU and will be accepted The actual MTU of the PPP connection will be set to the smaller one of MTU and the peer s MRU 5 24 What is Clone MAC Address Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address Since that all the clients will communicate outside world through the WLAN Broadband Router so have the cloned MAC address set on the WLAN Broadband Router will solve the issue V3 0 0 Q Loopcomm 5 25 What is DDNS DDNS is the abbreviation of Dynamic Domain Name Server It is designed for user owned the DNS server with dynamic WAN IP address 5 26 What is NTP Client NTP client is designed for fetching the current timestamp from internet via Network Time protocol User can specify time zone NTP server IP address 5 27 What is VPN
24. ce Providers The wizard will guide you through these three quick steps Begin by clicking on Mext Step 1 Configure LAN IP address settings Step 2 Configure Internet connection Step 3 Configure Wireless settings Step 1 configure LAN IP address settings Setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your SF ilnternet Service Provideri step 1 Configure LAN IF address settings ir Address 192 166 1200 Subnet Wask 1554552550 V3 0 0 W Loopcomm Step2 configure Internet connection Click Next button to next step for Internet connection settings There are five options DHCP Static Mode PPPOE L2TP PPTP for Internet connection on WAN port a DHCP Auto Configure setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connectto your lSPilnternet Service Provider step 2 Configure Internet Connection ee onneeen Type If you select DHCP option please click Next button to jump at Step3 V3 0 0 WO Loopcomm b Static Mode fixed IP If you select Static Mode fixed IP please fill in these fields on next page setup Wizard This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your lSPijnternet Service Provider step 2 Configure Internet Connection eee OTEELI Satie Mode ited IE iv Type me iP Address Dn
25. ction manually When you finish these settings then click Next button to jump at Step3 V3 0 0 WO Loopcomm d L2TP If you select L2TP please fill in these fields on next page setup Wizard This mode is tor home networking The Setup wizard will guide you to configure the router to connect to your lSPi nternet Service Provider Step 2 Configure Internet Connection WURA Connection LATE Type Lare serere aaaress userName LL Passware SY Address Mode i Static bw iF Address C Subnet Mask sd Default Gateway sd Operation Mode Keep Alive Mode Redial Period sencands met L2TP Server IP Allow user to make a tunnel with remote site directly to secure the data transmission Address among the connection User can use embedded L2TP client supported by this router to make a VPN connection If you select the L2TP support on WAN interface fill in the IP address for it Fill in the user name and password to login the L2TP server Password Fill in the user name and password to login the L2TP server Address Mode Static To configure the IP address information by manually please fill in the related setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface ou
26. ctions 5 15 What is Wi Fi Protected Access WPA W1 Fi s original security mechanism Wired Equivalent Privacy WEP has been viewed as insufficient for securing confidential business communications A longer term solution the IEEE 802 111 standard is under development However since the IEEE 802 111 standard is not expected to be published until the end of 2003 several members of the WI Fi Alliance teamed up with members of the IEEE 802 111 task group to develop a significant near term enhancement to Wi Fi security Together this team developed Wi Fi Protected Access To upgrade a WLAN network to support WPA Access Points will require a WPA software upgrade Clients will require a software upgrade for the network interface card and possibly a software update for the operating system For enterprise networks an authentication server typically one that supports RADIUS and the selected EAP authentication protocol will be added to the network 5 16 What is WPA2 It is the second generation of WPA WPA2 is based on the final IEEE 802 111 amendment to the 802 11 standard 5 17 What is 802 1x Authentication 802 1x is a framework for authenticated MAC level access control defines Extensible Authentication Protocol EAP over LANs WAPOL The standard encapsulates and leverages much of EAP which was defined for dial up authentication with Point to Point Protocol in RFC 2284 Beyond encapsulating EAP packets the 802 1x standard al
27. d This mode is for home networking The Setup Wizard will guide you to configure the router to connectto your lSPilnternet Service Providers step 1 Configure LAN IP address settings G Address 1321 66 1 200 Subnet blask 2554552550 V3 0 0 WO Loopcomm Step 2 configure Wireless Settings There are five options Disable Open WEP Shared WEP WPA PSK WPA2 PSK for Wireless security connection setup Wizard This mode is for bridge setting The setup Wizard will guide you to configure the mode to setting AP AP Client WWOS 4P or WDS step 2 Configure Wireless settings wireless Band wireless Mode gere Channel EE Network Name SSID channe Bandwidth Oog onno Security Mode Disable i Item Description Wireless Band Click to select wireless band from pull down menu Wireless Mode Click to select wireless mode from pull down menu Frequency Channel Select the wireless communication frequency channel from pull down menu Network Name SSID J It is the wireless network name The SSID can be 32 bytes long Channel Bandwidth Select the operating channel width 20 MHz or 20 40 MHz Security Mode Please select the security mode related wireless data encryption WEP When you select WEP please input 5 13 ASCII 10 or 26 HEX characters for WEP Key Pre Shared Key WPA PSK WPA2 PSK When WPA WPA2 Pre shared key encryption is selected please fill in the Pre shared key The format
28. d Service Set ESS is a set of two or more BSSs forming a single sub network Since most corporate WLANs require access to the wired LAN for services file servers printers Internet links they will operate in infrastructure mode Distribution System DS Basic Service Set BSS j Extended Service Set ESS Example 1 wireless Infrastructure Mode Ad hoc mode also called peer to peer mode or an Independent Basic Service Set or IBSS is simply a set of 802 11 wireless stations that communicate directly with one another without using an access point or any connection to a wired network This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services such as a hotel room convention center or airport or where access to the wired network is barred such as for consultants at a client site Independent Bask Service Set ID 5 Example 2 wireless Ad Hoc Mode V3 0 0 Q Loopcomm 5 5 What is BSSID A six byte address is that distinguish a particular a particular access point from others Also know as just SSID Serve as a network ID or name 5 6 What is ESSID The Extended Service Set ID ESSID is the name of the network you want to access It is used to identify different wireless networks 5 7 What are potential factors that may causes interference Factors of interference v Obstacles walls ceilings furniture
29. ds 60 9999 Access Access Policy WPA Cipher Suite O Tkp AES TKIPAES If you set Security Mode to WPAPSK or WPA2 PSK please fill in the related configurations as below WPA Cipher Suite Select TKIP AES or TKIPAES for WPA algorithms V3 0 0 Q Loopcomm Pre Shared Key Please fill in a passphrase like test wpa 123 or a hexadecimal string like OSE4 E123 456 El Key Renewal Please fill in a number for Group Key Renewal interval time Interval d WPA RADIUS WPA2 RADIUS Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from Unauthorized access and monitoring Security Wireless Security Mode IWPARADIUS Tse era Cipher Suite COTKIP AES TKIPAES Key Renewal Interval seconds 60 4440 Radius Server ie Address o Pon Shared Secret Session Timeout lie E Er Timeout IL Policy Disabiea_ Aad a station Mac Lo V3 0 0 WO Loopcomm Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from Unauthorized access and monitoring Security Made WPA2 RADIJS x WPA Cipher Suite OTK AES OTKIPAES Key Renewal Interval seconds EO 4440 Pm Cache Period fio minute Pre Authentication Disabled Enabled IP Adcress oO snared secret mn Session Timeout jo ite
30. e Protection WEP Default Key wee Key 1 WE ERE wee Key z IL re WEP Keys wer Key 3 Cid Hex 1 wee Key 4 Lo Hex Hex wl Access Policy 7 Policy Disabled sw Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring Security Wireless Security Mode SHABED WEP Te Wire Equivalence Protection WEP Default ESE mme et a a aeo WEP Keys dee m wer Key 3 sd Hex wer Key 4 sd Hex Access Policy If you set Security Mode to OPEN WEP or SHARED WEP please fill in the related configurations as below Default Key Specify a Key number for effective WEP Keys 1 4 When you select WEPAUTO please input 5 13 ASCII 10 or 26 HEX characters for WEP Key V3 0 0 Q Loopcomm c WPA PSK WPA2PSK Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from Unauthorized access and monitoring Security Wireless TE WPA Cipher Suite O TKP AES TKIPAES Pre shared Ke Key Renewal Interval 3600 seconds 60 9999 Access Policy Policy Disabled Add a station Mac Wireless Security Encryption Settings Setup the wireless security and encryption to prevent from unauthorized access and monitoring Pre Shared key Key Renewal Interval 3600 secon
31. ed between a mobile station e g a laptop with a wireless Ethernet card and an access point i e a base station The secret key is used to encrypt packets before they are transmitted and an integrity check is used to ensure that packets are not modified in transit V3 0 0 Q Loopcomm 5 10 What is Fragment Threshold The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802 11 to achieve parallel transmissions A large data frame is fragmented into several fragments each of size equal to fragment threshold By tuning the fragment threshold value we can get varying fragment sizes The determination of an efficient fragment threshold is an important issue in this scheme If the fragment threshold is small the overlap part of the master and parallel transmissions is large This means the spatial reuse ratio of parallel transmissions is high In contrast with a large fragment threshold the overlap is small and the spatial reuse ratio is low However high fragment threshold leads to low fragment overhead Hence there is a trade off between spatial re use and fragment overhead Fragment threshold is the maximum packet size used for fragmentation Packets larger than the size programmed in this field will be fragmented If you find that your corrupted packets or asymmetric packet reception all send packets for example You may want to try lowering your fragmentation threshold This will cause packets to be broken into sma
32. ess speed up to 150Mbps data rate gt Compatible with IEEE 802 1 1g standard to provide wireless speeds of 54Mbps data rate gt Compatible with IEEE 802 11b standard to provide wireless speeds of 11Mbps data rate gt Maximizes the performance and ideal for media centric applications like streaming video gaming and Voice over IP technology gt Support various operation Bridge Gateway Ethernet Converter modes between wireless and wired Ethernet interfaces gt Supports WPS 64 bit and 128 bit WEP WPA WPA2 encryption to protect the wireless data transmission gt Support TKIP AES TKIPAES of WPA algorithms gt Support IEEE 802 3x full duplex flow control on 10 100M Ethernet interface gt Support DHCP server to provide clients auto IP addresses assignment gt Support DHCP client static IP PPPoE L2TP and PPTP of WAN Interface gt Supports firewall security with port filtering IP filtering MAC filtering port forwarding DMZ hosting and URL filtering functions gt Support WEB based management and configuration gt Support System Log gt Support Dynamic DNS gt Support NTP V3 0 0 Loopcomm 2 3 Rear Panel Description LED Indicator on x x Off ON Off 1 PWR LED 2 WLAN LED 3 WAN LED Flashing Data is transmitting or receiving on the WAN interface Port linked Flashing Data is transmitting or receiving on the LAN interface 4 LAN LED V3 0 0 W Loopcomm 2 3 F
33. example 191 168 1 254 could be an IP address The MAC Media Access Control address is your computer s unique hardware number On an Ethernet LAN it s the same as your Ethernet address When you re connected to the Internet from your computer or host as the Internet protocol thinks of it a correspondence table relates your IP address to your computer s physical MAC address on the LAN To find your PC s IP and MAC address v Open the Command program in the Microsoft Windows v Type in ipconfig all then press the Enter button v Your PC s IP address is the one entitled IP Address and your PC s MAC address is the one entitled Physical Address 5 2 What is Wireless LAN A wireless LAN WLAN is a network that allows access to Internet without the need for any wired connections to the user s machine 5 3 What are ISM bands ISM stands for Industrial Scientific and Medical radio frequency bands that the Federal Communications Commission FCC authorized for wireless LANs The ISM bands are located at 915 13 MHz 2450 50 MHz and 5800 75 MHz V3 0 0 W Loopcomm 5 4 How does wireless networking work The 802 11 standard define two modes infrastructure mode and ad hoc mode In infrastructure mode the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations This configuration is called a Basic Service Set BSS An Extende
34. hannel Bandwidth O20 p40 Security moge WPA PSK w WPA2 PSK setup Wizard This mode is for home networking The setup Wizard will guide you to configure the router to connect to your ISP Internet Service Provider Step 3 Configure Wireless Settings wetn teng wireless Bana Band 802 11 B GIN lt Channel AutoSelect wl Current Channel 1 Network Name SSD Name SSID SOZ In Router Channe Bandwidth O0 ooo Security Mode WPAZ PSE When you finish these settings then click Apply button to save Choose either Client or WDS then click Next button to step 3 V3 0 0 W Loopcomm 4 3 1 3 WISP Mode This mode is for home networking The Setup Wizard will guide you to configure the router to connect to your ISP Internet Service Provider setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless how to connect anw AFS and setting WAN mode to connected internet The wizard will guide you through these four quick steps Begin by clicking on Mert Step 1 Configure LAN IP address settings Step 2 configure Internet connection Step 3 configure Wireless settings Step 4 Site survey APs to connected internet Step 1 configure LAN IP address settings setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless howto connect any APS and se
35. he housing is well installed Step4 Complete the hardware installation as diagram as below Install POE Injector DC Insert adapter POE This hole is linked to Secondary port of the Outdoor Router with RJ 45 LAN This hole is linked to LAN side PC Hub or Router ADSL modem device with RJ 45 There is no software driver or utility installation needed but only the configuration setting Please refer to chapter 4 for software configuration Notice It will take about 50 seconds to complete the boot up sequence after powered on the Outdoor Router Power LED will be active and after that the WLAN Activity LED will be flashing to show the WLAN interface is enabled and working now V3 0 0 Q Loopcomm 4 Software Configuration There are web based management and configuration functions allowing you to have the jobs done easily The Outdoor Router is delivered with the following factory default parameters on the Ethernet LAN interfaces Default IP Address 192 168 1 200 Default IP subnet mask 255 255 255 0 WEB login User Name admin WEB login Password admin V3 0 0 Q Loopcomm 4 1 Prepare your PC to configure the WLAN Broadband Router For OS of Microsoft Windows 2000 XP 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear 2 Move mouse and double click the right button on Network and Dial up Connections icon Move mouse and double click the Local Area Connec
36. ication setting Set to zero to disable 802 1x re authentication service for each session Session timeout interval unit is second and must be larger than 60 Idle Timeout Enter the idle timeout in the column V3 0 0 Q Loopcomm f Access Policy Policy Disabled Add a station Mac Select the Disabled Allow or Reject of drop down menu choose wireless access control mode This is a security control function only those clients registered in the access control list can link to this WLAN Broadband Router Add a station MAC Fill in the MAC address of client to register this AP router access capability V3 0 0 W Loopeomm 4 3 4 4 Station List station List You could monitor stations which associated to this AP here Wireless Network Wareless nemore MlM You could monitor stations which associated to this AP here V3 0 0 Q Loopcomm 4 3 4 5 WPS Wi Fi Protected Setup You could setup security easily by choosing PIN or PBC method to do Wi Fi Protected Setup WPS Config WPS Enabled Yv Apply WPS Current Status Idle WPS Configured Mo WPS SSID 802 11n_ Router WPS Auth Mode Open WPS Encryp Type Mone WPS Default Key Index WPS Key ASCII 37762520 Generate Select Enable or Disable the Wi Fi Protected Setup function Then click Apply button to take effect function after change After enabling the WPS function if
37. image file on PC And click i the Apply button to upgrade firmware 4 3 6 4 Backup amp Restore Backup amp Restore You might save system settings by exporting them to a configuration file restore them by importing the file or reset them to factory default Export Settings Export Button Import Settings Settings file location Import Cancel Load Factory Defaults Load Default Button Load Default Export Button Click Export button to export the current configuration to your PC Settings file Click Browse button to select the configuration file from your PC then click location Import button to update the configuration Load Default Click the Load Default button to reset the configuration parameter to factory Button defaults This page shows the current status and some basic settings of the device includes system info Internet Configurations and Local Network V3 0 0 4 3 6 5 Status This page shows the current status and some basic settings of the device includes system info Internet Configurations and Local Network Access Point Status This page show the current status and some basic settings of the device System Information Firmware Version 1 1 06 M A Mov 19 2012 system Up Time U days 0 hours 46 mins 41 secs Wireless ISP Mode Operation Mode Repeater Information Repeater status TA Repeater Device Re
38. ller fragments These small fragments if corrupted can be resent faster than a larger fragment Fragmentation increases overhead so you ll want to keep this value as close to the maximum value as possible 5 11 What is RTS Request to Send Threshold The RTS threshold is the packet size at which packet transmission is governed by the RTS CTS transaction The IEEE 802 11 1997 standard allows for short packets to be transmitted without RTS CTS transactions Each station can have a different RTS threshold RTS CTS is used when the data packet size exceeds the defined RTS threshold With the CSMA CA transmission mechanism the transmitting station sends out an RTS packet to the receiving station and waits for the receiving station to send back a CTS Clear to Send packet before sending the actual packet data This setting is useful for networks with many clients With many clients and a high network load there will be many more collisions By lowering the RTS threshold there may be fewer collisions and performance should improve Basically with a faster RTS threshold the system can recover from problems faster RTS packets consume valuable bandwidth however so setting this value too low will limit performance 5 12 What is Beacon Interval In addition to data frames that carry information from higher layers 802 11 include management and control frames that support data transfer The beacon frame which is a type of management frame
39. n Coding Scheme MCS MCS is Wireless link data rate for 802 1 In The throughput range performance of an AP will depend on its implementation of coding schemes MCS includes variables such as the number of spatial streams modulation and the data rate on each stream Radios establishing and maintaining a link must automatically negotiate the optimum MCS based on channel conditions and then continuously adjust the selection of MCS as conditions change due to interference motion fading and other events 5 33 What is Frame Aggregation Every 802 11 packet no matter how small has a fixed amount of overhead associated with it Frame Aggregation combines multiple smaller packets together to form one larger packet The larger packet can be sent without the overhead of the individual packets This technique helps improve the efficiency of the 802 1 In radio allowing more end user data to be sent in a given time 5 34 What is Guard Intervals GI A GI is a period of time between symbol transmissions that allows reflections from multipath from the previous data transmission to settle before transmitting a new symbol The 802 11n draft specifies two guard intervals 400ns short and 800ns long Support of the 400ns GI is optional for transmit and receive The purpose of a guard interval is to introduce immunity to propagation delays echoes and reflections to which digital data is normally very sensitive V3 0 0
40. n WPA WPA2 Pre shared key encryption is selected please fill in the Pre shared key The format can be passphrase or Hex 64 characters V3 0 0 W Loopcomm OPEN WEP setup Wizard This mode is for home networking The setup Wizard will guide you to configure the router to connect to your sPilnternet service Provider step 3 Configure Wireless Settings Wireless Settings O OO OOOO wireless Band SOZLLB G N Frequency Channel AutoSelect w Current Channel 1 Network Name SSID S02 l1n Router Channel BandWidth Don p0 Security Mode OPEN WEF W SHAREDWEP Setup Wizard This mode is for home networking The setup Wizard will guide you to configure the router to connect to your lsP lnternet service Provider step 3 Configure Wireless Settings Wireless Settings wireless Band a0 LLEIGIN en current Channel 1 Network Name SSID O04 lin Router Channel Bandwidth Cap o0 40 Security Made SHAREDWEP Pre shared key nn V3 0 0 W Loopcomm WPA PSK setup Wizard This mode is for home networking The setup Wizard will guide you to configure the router to connect to your ISPilnternet Service Provider step 3 Configure Wireless Settings Wireless Settings wireless Band C 802 11B G N I1B G N Frequency Channel AutoSelect m ect Current antosete Network Name SSID network Name SSID e02 11m Romer SOZ in 80211n_Router c
41. n ennnnnnnnereerenvens 76 5 4 How does wireless networking work asana eeen 77 SS Whats bye he IDS neenstemmen 78 50 Whats aca occas ce E E crass essaescesaaaaeeaeceemnten 78 5 7 What are potential factors that may causes interference 78 5 8 What are the Open System and Shared Key authentications 78 SI Whats WEBS oran E eee 78 5 10 What is Fragment Threshold aaneen 79 5 11 What is RTS Request to Send Threshold 79 5 12 What is Beacon Interval 0 0 0 0 cccccccccccecccaeeeseeeecceeeeeeaeeeeeeeceeeeeaaas 79 5 13 What is Preamble Type iissiccsveaceseiiieciacexedoeeeiiavciaccysosvaerwecisaetoloeseriewentens 80 5 14 What is SSID Broadcast a eeeeeeeeevennnnnens 80 5 15 What is Wi Fi Protected Access WPA eneen SO SO W hatis a bas 22 nn E eee eee 80 5 17 What is 802 1x Authentication aanne nennnnnnreeeeneevenn 80 5 18 What is Temporal Key Integrity Protocol TKIP 81 5 19 What is Advanced Encryption Standard AES 81 5 20 What is Inter Access Point Protocol TAPP cece ewes Sl 5 21 What is Wireless Distribution System WDS 81 5 22 What is Universal Plug and Play UPNP cc ceeesceeeeeeeeeeees 81 5 23 What is Maximum Transmission Unit MTU Size 81 5 24 What is Clone MAC Address
42. ng WAN mode to connected internet step 2 Configure Internet Connection WAN Connection Type IP Address _ Subnet Mask Lo Default Gateway Primary DAS Serer S Secondary DAS Server IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Primary DNS Fill in the IP address of Domain Name Server 1 Server Secondary DNS Fill in the IP address of Domain Name Server 2 Server When you finish these settings then click Next button to jump at Step3 V3 0 0 Q Loopcomm c PPPOE ADSL If you select PPPOE please fill in these fields on next page setup Wizard This made is use wireless to connected APS The Setup Wizard will guide you to configure the wireless howto connect any APS and setting WAN mode to connected internet step 2 Configure Internet Connection ali Connection Type User Name _ Pasewor _ SSS yo Operation Mode Keep Alive Mode Redial Period a senconds On demand Made Idle Time Besl minutes User Name If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Password If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Verify Password Fill in the password again for verification Operation Mode Keep Alive Keep
43. nnnnnssnssnrsersenven 43 A WV PRIN oo trsapnca daa este peea cite wh E E 43 SS DE oe ee eee ee eee 48 4 3 3 3 VPN Pass WOU Mees eeepc sosiecseenataaematneeteoent oen naad 49 4 3 4 Wireless Settings uuuuuunnns ereen nennennnnrreerereveenennens 50 EAL DIS ea E A E E 50 BZN VANCE ea EE E EES 52 EIES SOT S eeen 54 4 3 4 4 Station LISE sacrverevnenerneeree ccavenevewncindavedanrenetarsdua andoeteacrerndekeres 61 B AME eeen eneen E E eneen tavernes 62 Ais a E E art cegh sc NEIE E A AA 63 4 3 5 1 MAC IP Port Filtering nanne 63 4 3 5 2 Port Forwarding nanne ennennnnnnnneeeneeenenn 65 rd Dh Zn 67 ASSA System SO CUNY oreades 68 4 3 5 Content Filtering an eneen eten 69 4 3 6 AdministratlOn eeeeeeneeeenennnennnnnnsnnssnrserrsnnen 70 4 3 6 1 Management anorte noen Rsadi nies 70 V3 0 0 Q Loopcomm ESO OOS ictal vada se atresec ea ani A 12 4 3 6 3 Upload Firmware cccccccccccccecceececeeeeeeesssssseeseeeeeeeees 73 4 3 6 4 Backup amp Restore annaennnnene nennen 73 409 SALUS e eenen 74 4 3 6 6 System LOB ae nenennnnneeeeneenennnnnnneeeeneevens 75 5 FREQUENTLY ASKED QUESTIONS FAQ ccc ccnnsrsseseeeeeeeeees 76 5 1 What and how to find my PC s IP and MAC address 76 5 2 What is Wireless LAN s sadescte seach danissccectesteiasiscacte aE EENT 76 5 3 What are ISM bands nnnsennnnnnss eene
44. ouse and click Internet Protocol Version 4 TCP IPv4 then click Properties button 4 Move mouse and click General tab Select Specify an IP address and type in values as following example v IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 254is good to connect the Wireless LAN Access Point Don t use 192 168 1 200 v IP Subnet Mask 255 255 255 0 5 Click OK to complete the IP parameters setting V3 0 0 W Loopcomm 4 2 Connect to the WLAN Broadband Router Open a WEB browser i e Microsoft Internet Explorer 6 1 SPI or above then enter 192 168 1 200 on the URL to connect the WLAN Broadband Router 4 3 Management and configuration on the Outdoor Router 4 3 1 Wizard The setup wizard will be changed when the user selects different operation modes 4 3 1 1 Bridge Mode This mode is for bridge setting The Setup Wizard will guide you to configure the router to connect to your ISP Internet Service Provider setup Wizard This mode is for bridge setting The Setup Wizard will guide you to configure the mode to setting AP AP Client WWOS AP or WDS The wizard will guide you through these three quick steps Begin by clicking on Next Step 1 Configure LAN IF address settings Step 2 Configure Wireless mode settings Step 3 Configure WDS mode AP Client mode or AP mode or Apply Click Next button to next step for LAN IP address settings Step 1 configure LAN IP address settings setup Wizar
45. peater Mac Address Repeater Rool Wireless Information Status Fadia ON Mode J gt 0 aal din Router Channel Encryption Disable Hal 00 30 4F 93 BF E6 Connected Type DHCP mas S wooo e o z a V3 0 0 Q Loopcomm 4 3 6 6 System Log This page is used to view system logs system Log Syslog Jan Jan 1 01 49 36 ralink user Jan 1 01 49 39 ralink user Jan 1 01 49 39 ralink user Jan 1 01 49 39 ralink user Jan 1 01 49 41 ralink user 1 01 49 41 ralink user debug kernel debug kernel debug kernel debug kernel debug kernel ral no ethe 1 ethe 2 apolill br no 01 49 36 ralink syslog info syslogd started BusyBox wl 12 1 notice kernel klogd started BusyBox vl 12 1 2012 10 Py routers present no TPv6 routers present no TPv6 routers present no IPvh routers present IPyh routers present Click the Refresh button to refresh the log shown on the screen Clear Click the Clear button to clear the log display screen V3 0 0 Q Loopcomm 5 FREQUENTLY ASKED QUESTIONS FAQ 5 1 What and how to find my PC s IP and MAC address IP address is the identifier for a computer or device on a TCP IP network Networks using the TCP IP protocol route messages based on the IP address of the destination The format of an IP address is a 32 bit numeric address written as four numbers separated by periods Each number can be zero to 255 For
46. pp Remote Select Deny or Allow for remote management function management Ping form WAN Select Disable or Enable for Ping permit from WAN Filter SPI Firewall Select Disable or Enable for SPI firewall function V3 0 0 Q Loopcomm 4 3 5 5 Content Filtering Webs Host Filter Settings Add a Host keyword Filter r Current Website Host Filters CN Fill in a word for Webs Host Filter policy Make a mark for next action Delete Click Delete button to delete all that you selected Click Reset button to clear selected items Webs URL Filter Settings Add a URL filter URL Current Webs URL Filters Delete Reset URL Fill in a URL for Webs URL Filter policy Add Make a mark for next action Delete Click Delete button to delete all that you selected Reset Click Reset button to clear selected items V3 0 0 WO Loopcomm 4 3 6 Administration 4 3 6 1 Management Adminstrator Settings Passwor eesse _ NIP Settings current Time Sat Jan 1 05 19 03 UTC 2000 Time Zane CEMT 11 00 Midway land Sarna u NTP Server ex time nist goy htpO broad mitedu time stdtime gow t NTP synchronizationihours C Apply Cancel Item Description Username Fill in the user name for web management login control Password Fill in the password for web management login control Current Time It shows the current time Time Zone Select
47. provides the heartbeat of a wireless LAN enabling stations to establish and maintain communications in an orderly fashion Beacon Interval represents the amount of time between beacon transmissions Before a station enters power save mode the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point V3 0 0 Q Loopcomm 5 13 What is Preamble Type There are two preamble types defined in IEEE 802 11 specification A long preamble basically gives the decoder more time to process the preamble All 802 11 devices support a long preamble The short preamble is designed to improve efficiency for example for VolP systems The difference between the two is in the Synchronization field The long preamble is 128 bits and the short is 56 bit 5 14 What is SSID Broadcast Broadcast of SSID is done in access points by the beacon This announces your access point including various bits of information about it to the wireless world around it By disabling that feature the SSID configured in the client must match the SSID of the access point Some wireless devices don t work properly if SSID isn t broadcast for example the D link DWL 120 USB 802 11b adapter Generally if your client hardware supports operation with SSID disabled it s not a bad idea to run that way to enhance network security However it s no replacement for WEP MAC filtering or other prote
48. rom pull down menu V3 0 0 WO Loopcomm 4 3 4 Wireless Settings 4 3 4 1 Basic Basic Wireless Settings You could configure the minimum number of Wireless settings for communication such as Network Name SSID and Channel The Access Point can be set simply with only the minimum setting items Wireless Network wireless On Off Wireless OFF Current Status Radio ON Antenna Switch extemal intema wireless Band 02 1 1BE G N ssp Broadcast Network Mame SSID Enabled Disabled AP Isolation Enabled Disabled B5510 00 30 4F 93 BF E8 Frequency Channel Current Channel 1 operating Mode Mixed Mode Green Field channel BandWidth O 20 20 40 Guara Interval Long Auto Click Wireless OFF button to turn off wireless RF radio Click Wireless ON Wireless On Off button to turn on wireless RF radio Select Internal antenna or External antenna for using The default is using Antenna Switch Internal antenna Wireless Band Click to select wireless band from pull down menu It is the wireless network name The SSID can be 32 bytes long User can use SSID the default SSID or change it Broadcast Network Name Enable or disable the SSID broadcast function SSID Wireless network is similar to the virtual local area network All of the Wireless AP Isolation client devices can access each other completely When you enable this function it will turn off connection between wireles
49. ront Panel Description For external antenna You can use the SMA connector to connect with SMA connector 2 4GHz external antenna The RJ 45 sockets allow LAN connection through Category 5 cables Secondary Middle Support auto sensing on 10 100M speed and half full duplex comply with IEEE 802 3 802 3u respectively The RJ 45 socket allows WAN connection through a Category 5 cable Main Right Support auto sensing on 10 100M speed and half full duplex comply with IEEE 802 3 802 3u respectively Press continually the reset button about 5 10 seconds to reset the Reset Bottom l configuration parameters to factory defaults V3 0 0 W Loopeomm 3 Hardware Installation 3 1 Appearance and Interface Introduction Notes The product shot is for reference only please refer to physical product 1 LED Panel 2 Waterproof Sliding Door 3 Pass trough Ethernet cable from this hole 4 Push this button to remove upper housing V3 0 0 W Loopcomm 5 Pole Mount 6 Wall Mount a 7 Secondary port with POE 8 Main port 9 SMA connector for external antenna 10 Reset button V3 0 0 W Loopcomm 3 2 Hardware Installation Steps Stepl Push the button in the side to remove upper housing F Step2 Pass through Ethernet cable from the hole insert the cable to Secondary port Note RJ 45 8P8C Ethernet cable is required V3 0 0 W Loopcomm Step3 Install the upper housing and make sure t
50. rt Range Fill in the start port and end port number of source to restrict data transmission Select Accept or Drop to specify the action of filtering policies Make a comment for the filtering policy V3 0 0 Q Loopcomm Current MACI IP Port filtering rules in system No Source MAC address Dest IP Address Source IP Address Protocol Dest Port Range Source Port Range Action Comment Pkt Cnt Others would be dropped Make a mark for next action Delete Selected Click Delete Selected button to delete all that you selected Click Reset button to clear selected items V3 0 0 WO Loopcomm 4 3 5 2 Port Forwarding Virtual Server Settings You may setup Virtual Servers to provide services on Internet Part Forwarding Disable iP Address E Port Range LIL Protacol ECP amp UDP commer The maximum rule count is 32 5 Port Forwarding Select Enable or Disable the Port Forwarding function IP Address To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall fill in the IP address Port Range To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall fill in the port range Protocol Specify protocol TCP amp UDP TCP or UDP Comment Make a comment for the port forwarding policy V3 0 0 Q Loopcomm Virtual Server Virtual Server IP Address IL Public Port Private Port
51. s O OOo O Subnetmask E Default Gateway Primary DNS Server secondary DNS Gener Status IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Primary DNS Fill in the IP address of Domain Name Server 1 Server Secondary DNS Fill in the IP address of Domain Name Server 2 Server MAC Clone Take NIC MAC address of PC on LAN side as the MAC address of WANI interface V3 0 0 WO Loopcomm b DHCP Wide Area Network WAN Settings You may choose different connection type suitable for your environment Besides you may also configure parameters according to the selected connection type WAN Connection Type DHCP Auto config w DHCP Mode Status Fill in the host name of Host Name of DHCP server The default value is empty MAC Clone Take NIC MAC address of PC on LAN side as the MAC address of WAN interface V3 0 0 WO Loopcomm PPPoE Wide Area Network WAN Settings You may choose different connection type suitable for your environment Besides you may also configure parameters according to the selected connection type WAN Connection Type PPPoE ADSL iw UserName Lo password De verit Password Operation Mode Keep Alive Mode Redial Period Cn senconds On demand Mode Idle Time Be minutes status User Name If you select the PPPoE suppor
52. s clients Only allows connection V3 0 0 WO Loopcomm between wireless client and this AP router BSSID Show the MAC address of Wireless interface Frequency Channel Operating Mode Select Mixed Mode for 11b g n mode or Green Field for 11n mode Channel Bandwidth Select the wireless communication frequency channel from pull down menu Select the operating channel width 20 MHz or 20 40 MHz Select Long or Auto Guard intervals are used to ensure that distinct Guard Interval transmissions do not interfere with one another Only effect under Mixed Mode Select 0 7 or Auto from pull down menu The default is Auto Only effect under Mixed Mode V3 0 0 WO Loopcomm 4 3 4 2 Advanced Advanced Wireless Settings Use the Advanced Setup Hage to make detailed settings for the Wireless Adwanced Setup Includes items that are not available from the Basic Setup page such as Beacon Interval Control Tx Rates and Basic Data Rates EE Protection Mode Beacon Interval ms range 20 999 default 100 Data Beacon Rate DTIM ms range 1 255 default 1 Fragment Threshold irange 256 2346 default 2346 ars Threshold range 1 2347 default 2347 Tx Power range 1 100 default 100 short Preamble Enabled Disabled shor Slat Enabled Disabled Country Code US United States i B G Protection When protection is enabled in this mode it protects 802 1 1b
53. so defines EAPOL messages that convey the shared key information critical for wireless security V3 0 0 WO Loopcomm 5 18 What is Temporal Key Integrity Protocol TKIP The Temporal Key Integrity Protocol pronounced tee kip is part of the IEEE 802 111 encryption standard for wireless LANs TKIP is the next generation of WEP the Wired Equivalency Protocol which is used to secure 802 11 wireless LANs TKIP provides per packet key mixing a message integrity check and a re keying mechanism thus fixing the flaws of WEP 5 19 What is Advanced Encryption Standard AES Security issues are a major concern for wireless LANs AES is the U S government s next generation cryptography algorithm which will replace DES and 3DES 5 20 What is Inter Access Point Protocol LAPP The IEEE 802 1 If Inter Access Point Protocol LAPP supports Access Point Vendor interoperability enabling roaming of 802 11 Stations within IP subnet IAPP defines messages and data to be exchanged between Access Points and between the LAPP and high layer management entities to support roaming The APP protocol uses TCP for inter Access Point communication and UDP for RADIUS request response exchanges It also uses Layer 2 frames to update the forwarding tables of Layer 2 devices 5 21 What is Wireless Distribution System WDS The Wireless Distribution System feature allows WLAN AP to talk directly to other APs via wireless channel like the wireless
54. t going data packets Operation Mode Keep Alive Keep the L2TP connection all the time Please also configure the Redial Period field Manual Let user connect the L2TP connection manually When you finish these settings then click Next button to jump at Step3 V3 0 0 WO Loopcomm e PPTP If you select PPTP please fill in these fields on next page setup Wizard This mode is for home networking The Setup wizard will guide you to configure the router to connect to your lSPilnternet Service Provider Step 2 Configure Internet Connection WVAN Connection EFTE Type e en Operation Mode Keen Alive Mode Redial Period senconds PPTP Server IP Allow user to make a tunnel with remote site directly to secure the data Tg Address transmission among the connection User can use embedded PPTP chent supported by this router to make a VPN connection If you select the PPTP support on WAN interface fill in the IP address for it Fill in the user name and password to login the PPTP server Password Fill in the user name and password to login the PPTP server Address Mode Static To configure the IP address information by manually please fill in the related setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill
55. t on WAN interface fill in the user name and password to login the PPPoE server Password If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Verify Password Fill in the password again for verification Operation Mode Keep Alive Keep the PPPoE connection all the time Please also configure the Redial Period field On Demand Please configure the Idle Time field When time is up the PPPoE connection will disconnect The connection will re connect when any outgoing packet arise Manual Let user connect the PPPoE connection manually MAC Clone Take NIC MAC address of PC on LAN side as the MAC address of WAN interface V3 0 0 WO Loopcomm d L2TP Wide Area Network WAN Settings vou may choose different connection type suitable for your environment Besides you may alsa configure parameters according to the selected connection type WAN Connection Type LATE He L2TP Mode Server iP Lo UserName CS Password DO Address Mode tac wt IP adores C Subnet mask mn Default Gateway Operation Mode Kezen Alive Made Redial Period sentands Status Disable Server IP Allow user to make a tunnel with remote site directly to secure the data transmission among the connection User can use embedded L2TP client supported by this router to make a VPN connection If you select the L2TP support on WAN interface fill in the IP address
56. the PPPoE connection all the time Please also configure the Redial Period field On Demand Please configure the Idle Time field When time is up the PPPoE connection will disconnect The connection will re connect when any outgoing packet arise Manual Let user connect the PPPoE connection manually When you finish these settings then click Next button to jump at Step3 V3 0 0 Q Loopcomm d L2TP If you select L2TP please fill in these fields on next page setup Wizard This mode is use wireless to connected APS The Setup Wizard will guide you to configure the wireless how to connect any APS and setting YWAN mode to connected internet Step 2 Configure Internet Connection WAN Connection LATE Type Lame Server IP Address MO UserName _ Passwora _ adress Mode tate i G Address sd Subnet mask es Detauit Gateway es Operation Mode Keep Alive Mode Redial Period senconds el L2TP Server IP Allow user to make a tunnel with remote site directly to secure the data transmission Address among the connection User can use embedded L2TP client supported by this router to make a VPN connection If you select the L2TP support on WAN interface fill in the IP address for it Fill in the user name and password to login the L2TP server Password Fill in the user name and password to login the L2TP server Address Mode Static To configure the IP address information by manually please fill in the rel
57. the time zone in your country from pull down menu NTP Server Fill in NTP server IP address NTP Fill in a number to decide the synchronization frequency with NTP server synchronization V3 0 0 Q Loopcomm DDNS Settings Dynamic DMS Provider Account Dynamic DNS Click the drop down menu to pick up the right DDNS provider you registered Provider Fill in the account of DDNS you registered Fill in the password of DDNS you registered DDNS Fill in the domain name that you registered V3 0 0 WO Loopcomm 4 3 6 2 Qos Quality of Service Settings YOU may setup rules to provide Quality of Service guarantees for specific applications oval of Service Enable v Local IP Address eee Uplink Bandvidth khps Downlink BandwidthiKbps ve LPs e Domi Ban Se Item Description Uplink Speed Input uplink Maximum upload speed Downlink Speed Input downlink Maximum download speed Local IP Address Fill in the local IP address Uplink Bandwidth Fill limit upload bandwidth Downlink Bandwidth Fill limit downlink bandwidth V3 0 0 Q Loopcomm 4 3 6 3 Upload Firmware Firmware Upgrade Upgrade the Device firmware to obtain new functionality It takes about 1 minute to upload upgrade flash and be patient please Caution A corrupted image will hang up the system Update Firmware Apply Location Click the Browse button to select the new firmware
58. tion icon The Local Area Connection window will appear Click Properties button in the Local Area Connection window 3 Check the installed list of Network Components If TCP IP is not installed click the Add button to install it otherwise go to step 6 4 Select Protocol in the Network Component Type dialog box and click Add button 5 Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation 6 Select TCP IP and click the properties button on the Network dialog box 7 Select Specify an IP address and type in values as following example v IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 254 is good to connect the Wireless LAN Access Point Don t use 192 168 1 200 v IP Subnet Mask 255 255 255 0 8 Click OK to complete the IP parameters setting For OS of Microsoft Windows Vista 7 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear 2 Move mouse and double click the right button on Network Connections item The Network Connections window will appear Double click Local Area Connection icon then User Account Control window shown Right click Continue button to set properties 3 In Local Area Connection Properties window Choose Networking tab move m
59. tting WAN mode to connected internet step 1 Configure LAN IP address settings LAN Setup P Address 192 168 1200 Subnet Mast 2552552550 V3 0 0 W Loopcomm Step2 configure Internet connection setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless howto connect any APs and setting WAN mode to connected internet step 2 Configure Internet Connection WAN Connection State Mode lined Fii w Type static Mode fined IP DHCP ane Conte FFFOE ADSL IF Address LITE Subnet mask Secondary DNS sewer J Click Next button to next step for Internet connection settings There are five options DHCP Static Mode PPPOE L2TP PPTP for Internet connection on WAN port a DHCP Auto Configure setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless how to connect any AFS and setting WAN mode to connected internet Step 2 Configure Internet Connection eon DHCP auto Config 1 Type DHCP Mode Hostname optional E If you select DHCP option please click Next button to jump at Step3 V3 0 0 Q Loopcomm b Static Mode fixed IP If you select Static Mode fixed IP please fill in these fields on next page setup Wizard This mode is use wireless to connected APs The Setup Wizard will guide you to configure the wireless howto connect any APs and setti
60. ver Address Mode Static To configure the IP address information by manually please fill in the related setting at below Dynamic The option allows the machine to get IP address information automatically from DHCP server on WAN side IP Address Fill in the IP address for WAN interface Subnet Mask Fill in the subnet mask for WAN interface Default Gateway Fill in the default gateway for WAN interface out going data packets Operation Mode Keep Alive Keep the PPTP connection all the time Please also configure the Redial Period field Manual Let user connect the PPTP connection manually When you finish these settings then click Next button to jump at Step3 V3 0 0 WO Loopcomm Step 3 configure Wireless Settings There are five options Disable OPENWEP WPA PSK WPA2 PSK for Wireless security connection setup Wizard This mode is use wireless to connected APS The setup Wizard will guide you to configure the wireless how to connect any APS and setting WAN mode to connected internet step 3 Configure Wireless Settings Wireless Settings Wireless Band S04 LBG reauen Channel Current Network Name SSID 802 11n_Router Channel Bandwidth Oog 20 40 Security Mode Disable CPFEM WEP et JC Neat SHAREDWEP ek SHAREDWEP j WPAZ PSE E Item Description Wireless Band Click to select wireless band from pull down menu Frequency Channel Select the wireless communication frequency ch

5GHz Outdoor Router User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents