PGM-IMB User Manual 1 2
Contents
1. The minimum detection speed of crossing the protected zone threshold selection mode Min speed has three options 0 1 m s 0 2 m s 0 4 m s 1 13 The maximum detection speed of crossing the protected zone threshold selection mode Max speed has three options 4 m s 6 m s 10 m s 1 14 The distance control and adjustment mode Dist contr is applicable ONLY to the IMB 150RD and IMB 800 detectors On all others you will be able to see this mode however you will NOT be able to make any changes Also the distance indicated on any of the non supported detectors is NOT CORRECT it will always read 450 200m The IMB 150RD will have the values of 10 20m 20 40m 40 75m or 75 150m The IMB 800 will have the values of 60 100m 100 200m 200 400m or 400 800m If a signal value is blinking this means the maximum value was reached if external conditions change problems may occur 1 15 The lower gain level control and adjustment mode Level L has 6 values 1dB 2dB 3dB 4dB 5dB 6dB User Manual Page 6 PGM IMB 1 16 The upper gain level control and adjustment mode Level P has 4 values 1dB 2dB 3dB 4dB Note In the lower and upper gain level control and adjustment mode a scale is displayed where the gain value is indicated by the signal2. PGM IMB 5 T R 60 Caster Avonuo Woodbridge ON LAL 5Y9 Canada Re Tel 1 416 657 4434 SE Fax 1 416 650 9012 a security technology research Toll Free 1 868 534 28TR IMB Series Programming Device PGM IMB USER MANUAL Toll Free 1 886 534 2STR Phone 1 416 657 4434 Fax 1 416 650 9012 www STRsecurity com support STRsecurity com User Manual Page 1 PGM IMB Revision 1 2 23 02 2009 Contents Introduction 1 Description and technical specifications 1 1 Application 1 2 Mode description 1 3 Power 1 4 Connection 1 5 Temperature ranges 1 6 Dimensions 1 Using the device 1 8 Indication mode 1 9 Method mode 1 10 Frequency mode 1 11 Tuning mode 1 12 Minimum speed mode 1 13 Maximum speed mode 1 14 Distance control mode 1 15 Lower gain level mode 1 16 Higher gain level mode 2 Packaging 3 Device lifetime and storage 4 Warranty terms and conditions User Manual Page 2 PGM IMB This operation manual contains information concerning the application design operation technical specifications of the PGM IMB device as well as installation and maintenance instructions necessary for the most effective usage of its technical potential Attention 1 We always work on improving our equipment therefore changes may be made at any time which will not affect normal operation of the equipment 1 Description and technical specifications 1 1 Th
3. ct to accident misuse and abuse or operated contrary to the instructions provided The opinion of STR with respect to this matter shall be final This warranty does not include and is not extended to broken and damaged accessories batteries and to parts wearing out due to normal wear and tear Proper Delivery Returned products will not be accepted for warranty repair unless accompanied with a valid Return Merchandise Authorization RMA number issued by STR RMA numbers issued by STR are valid for 15 days Shipments received after 15 days will be refused The unit must be shipped freight prepaid or delivered to the STR service facility in either its original package or similar package affording an equal degree of protection and with instructions indicating the location within Canada or the United States to which the unit will be returned The repaired unit will be returned to the customer freight prepaid unless the warranty claim is deemed void or invalid All accessories included with the unit must be listed individually on the packing slip for the shipping documentation STR will not accept any liability for loss or damage to such accessories if they are not listed Proof of Purchase Date This warranty applies and commences to STR products from the original date of purchase from an Authorized Re seller Proof of purchase i e photocopy of invoice must be included with product when submitting for warranty repair Warranty Limitation
4. e PGM IMB device is used to control and fine tune most of the IMB series of detectors IMB 150RD IMB 800 IMB 100 and etc 1 2 The device allows to control detectors and change parameters in the following modes of operation Display status Selection of detection distance and threshold Frequency adjustment Device calibration Selection of bottom detection speed threshold Selection of top detection speed threshold Control signal gain 1 3 The device draws power directly from the detector 1 4 The device is connected to the detector either through an onboard jack or through a jack in the distribution box e g IMB 150RD using the enclosed cable User Manual Page 3 PGM IMB 1 5 The device is able to function outdoor in temperatures ranging from 20 to 50 C 4 to 122 F and relative air humidity of 95 at 25 C 1 6 The size of the device is 115x65x40mm 4 5 x2 5 x1 6 and the weight without cable is 100gr 0 21lbs The PGM reads current signal values from the processor onboard the receiver of most IMB series and allows recording new values The signals are shown using an LCD display 3 buttons are used to control the device P changes modes In order to use the device it must be connected to an IMB series detector using the supplied cable The LCD screen on the device should read IMB xxx Tester In order to select a mode you must press the P button this i
5. frequency value Altern for an alternative frequency value in case of interference Important If you change the frequency value on the receiver you must change the frequency of the transmitter In order to do so you must connect the wire marked F to the ground wire in case of an older series detector or put a jumper on the F selector inside the casing You will determine which detector you have newer or older simply by the presence of wires our new detectors don t have any wires and come with terminal blocks 1 11 In the Tuning mode you can see the level of received signal in decibels from 2 to 70 For convenience the signal is partially displayed up to 20dB using an indicator The starting point of the indicator changes automatically during the tuning process This mode may have the following MESSAGES Ranget the signal level is out of the working range If a signal value is blinking this means the maximum value was reached if external conditions change problems may occur User Manual Page 5 PGM IMB The maximum tuning mode usage time is 5 minutes When this time elapses the device will automatically quit this mode In order to re enter this mode you must use the P button again In this mode and when you leave and enter the mode data is being written to the non volatile memory of the receiver this is indicated by a flashing rectangle in the lower right corner of the LCD 1 12
6. level by and block activation is indicated by in the lower right corner of the LCD 2 Packaging Your package should include the detector this user manual and a connector cable 3 Device lifetime and storage The MTTF of the device is approximately 8 years The PGM IMB may be stored in it s original packaging in storage facilities with the air temperature from 5 up to 40 C and relative humidity not exceeding 80 User Manual Page 7 PGM IMB Warranty Information Terms amp Conditions LIMITED WARRANTY STR hereby warrants subject to the conditions here in below that should this product become defective by reason of improper workmanship or material defect during the specified warranty period STR will repair the same effecting all necessary parts without charge for either parts or labor or replace the unit at STR s discretion Labor ONE 1 Year from the date of original purchase from authorized Re seller unless otherwise specified Parts ONE 1 Year from the date of original purchase from authorized Re seller unless otherwise specified Void Warranty Purchaser warranty will be void and purchaser waves any rights to make warranty claim if product has been opened altered or modified repaired or serviced by anyone other than the service facilities authorized by STR to render such services Further the seal serial number on the unit must not have been altered or removed The unit must not have been subje
7. ne We only use your personal information to service your account to provide you with the products you inquire about and request and to inform you of additional products or services that may benefit you User Manual Page 9
8. nt of reason for return e Customer is responsible for all freight charges duties and taxes if applicable Product must be properly packaged and shipped Prepaid to STR in its original packaging or similar packaging that offers an equal degree of protection STR will charge the full replacement cost for any missing components or parts STR is not responsible for lost or damaged merchandise We strongly recommend insuring products for return shipping e Return claims are void if manufacturer s seal is broken and or products are altered or modified subjected to an accident improper handling improper installation misuse and abuse or operated contrary to the operating instructions Products returned that are not in re saleable condition will be returned to customer at their expense e Discontinued items special or custom made equipment items items not carried as stock even though they may appear on price lists may not be returned Returned products will be evaluated at the original purchase price and not at any subsequent price increase or decrease Subject to the conditions stated above the following re stocking fees will apply to products returned for credit refund STR reserves the right to determine the validity of the product returned and or refuse to accept product for credit 0 Re Stocking Fee less original shipping charges If product is returned within 30 days from original STR ship date 25 Re Stocking Fee less
9. original shipping charges If product is returned within 60 days from original STR ship date 50 Re Stocking Fee less original shipping charges If product is returned within 90 days from original STR ship date 100 Re Stocking Fee 0 credit If product is returned after 90 days from original STR ship date DISCLAIMER In no event will STR or any of its affiliates be liable for any indirect special punitive consequential liability or incidental damages upon any basis of liability whatsoever even if advised of the possibility of such damages In addition STR does not take any responsibility or assume any liability for the wiring installation or placement of the equipment Customer purchases or for the activities of any other individual or entity such as Customer s Company those who prepare the specifications or any local Authorities who inspect or approve Customer s installation PRIVACY POLICY STR does not collect personally identifying information about you except when you specifically provide it to us Forms you may fill out that request personal information such as your mailing address telephone number e mail address etc will not be disclosed to any third party companies www STRsecurity com is for information purposes Distribution duplication modification or revision of the contents of this site is strictly prohibited without the explicit written permission of STR STR is committed to safeguarding your privacy onli
10. s This warranty does not cover maintenance or check ups if required This warranty gives you specific legal rights and you may also have other rights which vary from state province to state province Some states provinces do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts therefore the above exclusions or limitations may not apply to you STR is not responsible or liable for indirect special incidental or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to loss of property loss of revenues or profit or cost of removal installation or reinstallation PRODUCT RETURNS 30 Day Product Return Policy If you are not satisfied with a product you may return it to STR within 30 days from original date of shipment within the following conditions User Manual Page 8 PGM IMB e Original shipping charges are not refundable unless deemed that STR shipped incorrect item s incorrect quantity ies or original manufacturers defective product subject to STR validation e Returned products will not be accepted unless accompanied with a valid Return Merchandise Authorization number RMA e RMA numbers issued by STR are valid for 15 days Shipments received after 15 days will be refused e Returns must include a copy of original invoice the completed STR packing slip and a detailed stateme
11. s when the Indic message should appear on the LCD screen meaning you are able to select the Indication mode which is the first one in the menu Use the directional buttons to select the required mode An ability to enter a mode is confirmed by displaying the P sign in the lower left corner of the LCD If the P button is pushed a second time the chosen mode will be entered 1 8 The Indication mode allows to see the following detector conditions Pow power level drop below acceptable levels AV alarm LU low level block activation LP mid level block activation HL high level block activation User Manual Page 4 PGM IMB 1 9 The Selection of detection distance and threshold mode Method on the PGM IMB has two options Auto for automatic device operation Manual for manual adjustments The correct option can be selected using the directional keys In order to exit the mode and save changes in this or any other modes the P button must be pressed The process of saving changes is indicated by a flashing rectangle in the lower right corner of the LCD Note when the Auto option is selected you can only see indication of the set parameters you cannot actually change them In the Manual option you can change parameters 1 10 The frequency adjustment mode Mod Freq has two options Main for the main
Download Pdf Manuals
Related Search