- American Diagnostic Corporation
Contents
1. Use only a soft dry cloth to clean the device Do not use gasoline paint thin X ner chemicals such as strong bases strong acids oxidizing agents and re 29 ducing agents or other strong solvents on the unit Since the cuffs may absorb perspiration and other fluids inspect them for stains and discoloration X after each use Sponge with a damp cloth If necessary the cuff can be washed in cool water with mild soap or detergent disinfectant Remember to remove the bladder prior to washing After washing the cuff should be rinsed and al lowed to air dry NEVER iron When storing the device do not place heavy objects on it and do not coil BLADDER TUBE too tightly When the unit has been stored at a temperature below the freezing point keep it for at least 1 hour in a warm place before using Remove 24 the battery if the device is to be stored for an extended period of time Keep the batteries out of the reach of children Caution Do not disassemble or modify the device We suggest that the device be checked every 2 years This operation may only be performed by the manufacturer or by firms authorized by the manufac turer Caution Do not inflate the cuff when it is not wrapped around an arm Checking pressure accuracy Connect a cuff wrapped around a firm cylinder to the 9002 e sphyg 2 and a standard manometer Turn on the 9002 e sphyg 2 while pressing and holding the START STOP button down Release2. Err 2 MEASUREMENT ERROR Measurement could not be made because of moving or talking during measurement INFLATION ERROR AIR PLUG is not correctly inserted Noise was detected DEFLATION ERROR Movement or talking was CHECKING MODE See page 21 detected during measurement Extreme changes in pressure occurred during measurement NO POWER AC ADAPTER is not correctly connected Battery is exhausted Nothing is being displayed when MAIN POWER SWITCH is pressed down in the ON position 9002 was left turned on but has not been operated for over an hour Make sure that the patient stays still during measurement Make sure the patient remains still and quiet during measurement Reinsert AIR PLUG and make sure that it is securely inserted Make sure that the patient stays still and quiet during measurement Make sure the patient remains still and quiet during measurement Do not let patient move during measurement Turn off the device once and then turn it on again to take measurement Reinsert AC ADAPTER and make sure that it is securely inserted Charge the battery or use AC ADAPTER Turn off the device or press START STOP button or SET MEMORY button to activate the device from energy saver mode Error Displays and Troubleshooting ERROR SYMBOL SYMPTOM x CUE REMEDY Measurement is interrupted once and the cuff is inflated again Blood pressure is differen
3. with small 3mm allen key provided Place cuff storage basket on top of stainless steel inner pole making sure the pole goes completely inside collar and tighten allen bolt with key Figure 3 Attach manometer to basket using 6mm allen bolt and washer as shown Tighten securely with large 6mm allen key Figure 4 Connect tubing as noted in Wall configuration 4 Adjust height of manometer by loosening adjusting knob and raising or lowering inner pole until gauge is at de sired height Tighten adjusting knob by hand Figure 5 Figure 3 Figure 4 Figure 5 Cuff Connections PLUG PORT 1 Squeeze the middle of the plastic air connector CONNECTION on theend of coiled tubing between thumb and forefinger and insert into the air connection port on vA AIR CONNECTOR the face of the e sphyg 2 Make sure connector Coiled Tubing firmly lock snaps into the port Figure 1 Figure 1 l 2 Firmly insert male connector of coiled tubing Figure 2 into female connector at end of the Adcuff MALE bladder tubing Be sure the connectors are CONNECTOR tight Figure 2 Coiled Tubing E FEMALE CONNECTOR Bladder Tube Taking Blood Pressure Auto Mode Turn on the device by pressing I side of MAIN POWER SWITCH Move MODE SELECTOR downward and set the device to AUTO See page 15 for MANUAL measurement MANUAL Set the initial inflation value with PRESET PRESSURE KNOB Select the pressur
4. allows you to use the time proven auscultatory method to obtain blood pressure readings Thank you for your patronage It is indeed our pleasure to serve you Sincerely American Diagnostic Corp ADC 9002 e sphyg 2 Table of Contents Introduction and Intended Use 4 Warnings and Precautions 5 FTOBUCE POT BS u mane nage tay d ob arida Sack p dio N 6 Name and Function of Each Part 1 8 Preparation for Use 9 10 How to Assemble Wall Model 11 How to Assemble Mobile Model 12 CUT GOMMCCUONS decet dva Wu ad ded A 13 Taking Blood Pressure 13 16 Memory Function 17 Error Displays and Troubleshooting 18 20 Care and Maintenance 21 Wall Unit Parts and Tools 22 Mobile Unit Parts and Tools 29 Mobile Base Assembly 24 Specifications 25 Limited Warranty 26 Replacement Parts 2 This manual is intended to assist the user in the safe and efficient operation of the Automatic Sphygmo manometer 9002 The pro
5. the button after the initial display all seg ment display disappears Two O s are displayed and the 9002 9002 e sphyg 2 is in CHECKING MODE Inflate the cuff with an d inflation bulb and compare the readings Pressure accuracy is to be 3mmHg Contact dealer if accuracy of your 9002 e m iS bs BLADDER 9002 sphyg 2 is invalid TUBE PORT A test kit may be purchased from an authorized dealer 9002W Wall Unit Parts amp Tools ADC Item e sphyg 2 6mm Allen Wrench Wall Bracket Wall Basket with 3 screws 3 mollys Coiled tubing Mounting Bolt Washer 1 Connector Connector Male 9 Connector Female 10 Adcuff amp Bladder Adult 11 2 Screws for wall bracket 12 2 Mollys for wall bracket Ex per 2 foo 4 ST ol 972 101 7 iii 885N 9002 2 Item no 9002 752M 116 952 103 2 752 116 952 025 8850 972 101 9002 2 891M 891F 845 11 ABK IF 952 104 952 105 891F 845 11 ABK IF 952 105 Se be ee FS 1 10 ADC Item e sphyg 2 6mm Allen Wrench 3mm Allen Wrench Mounting Bolt Washer 2 Mobile Stand Coiled tubing Connector Connector Male Connector Female Adcuff amp Bladder Adult 9002M Mobile Unit Parts amp Tools Item no 9002 752M 116 752M 117 972 101 752M 02 885N 9002 2 891M 891F 845 11ABK IF 752M 116 752M 117 3 Q B B 7 972 101 9002 2 9 8
6. 6 mm W x D x H Symm Dei Symbol Dem m Important Warning Caution net Latex Free Manufacturer s Information circumference Size Conforms to EU Standards Limited Warranty American Diagnostic Corporation ADC warrants its products against defects in materials and workmanship under normal use and service as follows 1 Warranty service extends to the original retail purchaser only and commences with the date of delivery 2 The entire sohygmomanometer is warranted for two years 3 Cuff bladder and coiled tubing are warranted for three years 4 The manometer is warranted to remain accurate to 3mmHg over its full range when compared to a reference standard for life What is Covered Repair or replacement of parts and labor What is not covered Transportation charges to and from ADCe Damages caused by abuse misuse accident or negligence Incidental special or consequential damages Some states do not allow the exclusion or limitation of incidental special or consequential damages so this limitation may not apply to you To Obtain Warranty Service Send item s postage paid to ADC Attn Service Dept 55 Commerce Dr Hauppauge NY 11788 Please include your name and address daytime phone no proof of purchase a brief note explaining the problem and 2 00 to cover the cost of return shipping and handling Implied Warranty Any implied warranty shall be l
7. 85 891 891F 845 11 ABK IF Mobile Base Assembly Parts NASA 972 080 asket Rubber Casters 5 972 106 nner Pole Single Caster 972 106 1 Basket Tightening Key Sw 9 Basket 972 108 Operating Principle Indicator Pressure Indicating Range Measuring Range Accuracy Inflation Deflation Exhaust Power Supply Power Consumption Memory Operating Environment Storage Environment Coverage Arm Circumference Adult Size Cuff Large Adult Size Cuff Small Adult Size Cuff Main Unit Weight Size Specifications are subject to change without notice due to improvements in performance marks only apply to AUTO measurement Specifications Oscillometric method 300 digits column LCD and 10 digits segment LCD 0 to 300 mmHg cuff pressure 90 to 250 mmHg systolic 40 to 180 mmHg diastolic 40 to 160 bpm pulse rate 3 mmHg cuff pressure 5 of reading pulse rate Automatic inflation Electric control valve Automatic exhaust valve 7 0 VDC AC adapter MODEL 9605 02225 1U0C or 4 8 VDC rechargeable NiMH battery 14W max Single measurement result 50 F to 104 F 15 to 90 relative humidity 4 F t0 122 F 15 to 95 relative humidity 9 0 to 15 7 inches 23 0 to 40 0 cm 13 3 to 19 6 inches 34 0 to 50 0 cm 7 4 to 10 6 inches 19 0 to 27 0 cm Approx 2 2 Ib 1000 g without AC adapter or battery 5 4 x 10 6 x 3 8 in 136 x 266 x 9
8. TIC CORPORATION ADC Inspected in the U S A 2 tel 631 273 9600 1 300 232 2670 Hauppauge NY 11788 el 09 1 2 3 j A OU ee 4 fax 631 273 9659 www adctoday com ADC UK Ltd email P aun com Unit 6 PO14 1TH I United Kingdom IB p n 93 9002 00 rev 8 english
9. TION MARK j DA DEFLATION MARK oa us COLUMN LCD HDI BATTERY MARK POWER MARK PRESET PRESSURE KNOB START STOP BUTTON SET MEMORY BUTTON AC INDICATOR MODE SELECTOR AIR PLUG AIR CONNECTOR BATTERY COMPARTMENT AC ADAPTER JACK COVER MAIN POWER h MM BATTERY 2 BATTERY PLUG I CONNECTOR ON Gui ADAPTER PLUG Name and function of each part Cuff Sizes SMALL ADULT ADULT LARGE ADULT Arm circumferences of 7 4 10 6 Arm circumferences of 9 0 15 7 Arm circumferences of 13 3 19 6 19 0 27 0cm 23 0 40 0cm 34 0 50 0cm LUER CONNECTOR Male Luer to Female Blad BLADDER TUBE der Tube Female Luer Connection COILED TUBING AIR ADCUFF CONNECTOR to main unit AC ADAPTER RECHARGEABLE INSTRUCTION NICKEL METAL HYBRID MANUAL NiMH BATTERY ADAPTER PLUG BATTERY PLUG e sphyg 2 Other parts included depending upon model selected Preparation for Use Connecting and Using the AC Adapter All models Connect AC ADAPTER PLUG to AC ADAPTER JACK Plug AC ADAPTER in the power socket AC INDICATOR is lit when AC ADAPTER is connected correctly Installing the RECHARGEABLE NiMH Battery All models NOTE The battery enclosed in the product package is not charged and needs to be charged for about 4 hours before use NOTE Turn off the power and unplug AC ADAPTER
10. arm How to Assemble Wall Model Securely attach wall bracket to flat surface using enclosed mollys and screws at desired height t is advised to use a level to ensure proper mounting Figure 1 Attach manometer to wall bracket by lowering atop wall bracket sliding male tab into female seat of the bracket Se cure the two together using the 6mm allen bolt and washer from below Tighten securely with large 6mm allen wrench Figure 2 Securely attach cuff basket to flat surface to left of manome ter using enclosed mollys and screws at desired height It is advised to use a level to ensure even mounting Figures 3 4 Attach 8 foot length coiled tubing to air inlet on face of e sphyg Figure 5 Insert male luer connector 891M on free end of coiled tubing to female connector 891F on bladder tubing Figure 6 Fold cuff and store in basket Figure 4 Figure 5 Figure 3 em Figure 6 How to Assemble Mobile Model i With base on its side connect upright outer pole to base using large 6mm allen bolt Tighten with large 6mm allen key provided Tighten hardware as securely as possible Note To prevent loosening hardware must be tightened securely and periodically checked Figure 1 Slide spring and stainless steel inner pole inside outer UL pole with open end up Figure 2 Figure 1 Loosen 3mm allen bolt on collar of cuff storage basket
11. asurement Allow your patient to rest for at least 5 minutes Error Displays and Troubleshooting ERROR SYMBOL SYMPTOM x CAUSE REMEDY Measurement result Blood pressure was taken in Measurement result is saved cannot be recalled or MANUAL mode only when it is taken in is not stored AUTO mode Measurement cannot be Cuff inflation does Battery is exhausted made when BATTERY MARK not start is displayed Recharge the battery AC INDICATOR is lit AC INDICATOR also indicates even when 9002 is The battery is inserted whether the battery is being turned off charged or it is not being charged Difference in voltages The column LCD is between AC ADAPTER and dim or brightness is 9002 is operated with the battery lead to differences not steady the battery in LCD brightness This does not indicate a functional problem If you cannot get correct measurement with the methods above do not tamper with the internal mechanism Contact your dealer If the unit malfunctions return it to the dealer or an authorized service representative for servicing according to the warranty The manufacturer provides service data to qualified dealers Care and Maintenance Because the device includes precision parts care should be taken to avoid extreme temperature variations humidity shock dust and direct sunlight Do not drop or strike the device Make sure not to expose the unit to moisture This unit is not water resistant
12. be fore inserting the battery Make sure O side of MAIN POWER SWITCH is pressed down Remove BATTERY COMPARTMENT COVER by loosening and removing the screw Fig 1 Connect BATTERY PLUG to BATTERY CONNECTOR inside the battery compartment and insert the battery Fig 2 Put back BATTERY COMPARTMENT COVER and close it by inserting and tightening the screw Connect AC ADAPTER PLUG and plug AC ADAPTER in the power socket to charge the Fig 3 battery The battery is charged regardless of whether the e sphyg 2 is powered on or off s ORANGE charging Orange light of AC INDICATOR indicates that the battery is being charged Fig 3 The battery is fully charged after approximately 4 hours The color of the AC INDICATOR may switch to green and return to Unplug AC ADAPTER after the light turns 2 green as it indicates the battery is charged does not indicate a problem Cop BATTERY MARK flashes in the segment LCD when the battery charge is low Only a few more measurements remain before the battery runs down BATTERY MARK The battery needs to be recharged when BATTERY MARK is displayed mark Measurement cannot be made NOTE The rechargeable batteries may not be completely full after their initial charge or when they have not been used for an extended period of time This should be solved once the unit has been used a few times and the batteries have been charged and discharged Battery l
13. ct Features DUAL DISPLAY COLUMN LCD and SEGMENT LCD Simulated Mercury Column The pressure can be read in the column LCD height and as digital value in the segment LCD DUAL MEASUREMENT MODE AUTO and MANUAL Modes of Measurement Determination of blood pressure can be made either automatically by the oscillometric method or manually by the auscultatory method using a stethoscope MODE DEFLATION RATE MEMORY AUTO Maintained at 4 0 to 4 9mmHg sec Last measured result auto saved MANUAL Maintained at preset rates of N A 2 5 4 5 or 6 5mmHg sec Cuff Sizes Auto Mode The Small Adult size cuff will accommodate arms of approximately 7 4 to 10 6 inches 19 0 to 27 0 centimeters A Small Adult cuff should be used on patients 12 or older only in auto mode The Adult size cuff will accommodate an upper arm circumference range of approximately 9 0 to 15 7 inches 23 0 to 40 0 centimeters The Large Adult size cuff will accommodate that of approximately 13 3 to 19 6 inches 34 0 to 50 0 centimeters Cuff Sizes Manual Mode In manual mode any of ADC s9 5 cuff sizes child small adult adult large adult or thigh may be used on any patient Operation with AC Adapter or Rechargeable Battery The digital ADC9 e sphyg 2 sphygmomanometer is powered by either an AC Adapter or rechargeable nickel metal hybrid NiMH battery both included Name and function of each part MAIN UNIT SEGMENT LCD INFLA
14. duct must be used in accordance with the procedures contained in this manual and must not be used for purposes other than those described herein It is essential to read and understand the entire manual Introduction and Intended Use The 9002 digital ADC e sphyg 2 sphygmomanometer is a digital sphygmo manometer intended for measurement of systolic and diastolic blood pressure and pulse rate in adult patients i e age 12 and above This product is not designed for neonatal use Inaccurate readings may result if it is used on a child s arm Accuracy was evaluated during clinical studies in which results with the 9002 digital ADC e sphyg 2 sphygmomanometer were compared with simultaneous ausculta tory measurements obtained with a standard sphygmomanometer In these studies the onset of the fourth or fifth Korotkoff sound was taken as the diastolic pressure for the purpose of determining overall efficacy A copy of this study is available from ADC on request To ensure that accuracy is maintained compare readings obtained with the 9002 digital ADC e sphyg 2 sphygmomanometer with values measured by a trained observer using a manual sphygmomanometer at least every 6 months Blood pressure measurements determined with this device are equivalent to those ob tained by a trained observer using the cuff stethoscope auscultatory method within the limits prescribed by the American National Standard Manual electronic or automated sph
15. e approximately 30 to 40 mmHg above expected systolic pressure AUTO Pressure can be set between 100 mmHg and 280 mmHg Set the pressure at 180 mmHg if patient s systolic pressure is PRESET PRESSURE difficult to predict 180 The cuff is re pressurized to a higher value if the preset 140 nt pressure is too low for blood pressure to be taken during cuff 28 deflation 100 Apply the cuff to patient s arm Choose the right size of cuff for your patient NOTE Only these 3 cuffs may be used in auto mode ARM CIRCUMFERENCE CUFF SIZE 9 0 to 15 7 inches 23 0 to 40 0 cm ADULT 13 3 to 19 6 inches 34 0t050 0cm LARGE ADULT 7 4 to 10 6 inches 19 0 to 27 0 cm SMALL ADULT The lower edge of the cuff should be about 1 2 to 3 cm above the inner elbow and BLADDER TUBE should be over the inner part of the arm positioning the ARTERY MARK of the cuff over the brachial artery Press the surface of the cuff to make sure that the hook and loop adhesive fastens securely The cuff should be wrapped loosely enough so that two fingers can be placed between the cuff and patient s arm If the cuff is wrapped tighter or looser than this inaccurate blood pressure readings may result If your patient is wearing a shirt that might restrict circulation in his her upper arm or he she rolls his her sleeve up over the upper arm the blood flow will be restricted preventing accurate measurement Press START STOP button The cuf
16. e sphyg 2 9002 Automatic Sohygmomanometer gt 2 8 B j o e 8 8 AMERICAN DIAGNOSTIC CORPORATION A Special Thank You Thank you for choosing an ADC blood pressure instrument We re proud of the care and quality that goes into the manufacture of each and every item that bears our name Only the finest materials are used to assure you of a timeless instrument designed for optimum performance You ll quickly appreciate the results for you now own one of the finest sphygmomanometers that money can buy With proper care and maintenance your ADC blood pressure instrument is sure to provide you with many years of dependable service Please read the following instructions and general information which will prove helpful in allowing you to enjoy your ADC product Advantages of Digital Your new ADC e sphyg 2 sphygmomanometer is intended to provide you with all of the func tionality of a traditional sphygmomanometer with none of the problems associated with these devices Using state of the art technology your e sphyg 2 sphygmomanometer will provide you with per formance versatility and reliability exceeding the most popular aneroid and mercurial instruments Its dual mode design will permit the instrument to fully measure a patient s blood pressure and pulse automatically In manual mode it
17. ed from the cuff when pressure descends to 30 mmHg Turn off the device by pressing O side of MAIN POWER SWITCH The device will be in the energy saver mode approximately after d 3 minutes if it is not turned off See page 10 POWER MARK Make sure your patient is relaxed has taken at least 5 minutes of rest before measurement and refrains from talking or moving during measurement Confirm that the cuff is kept at the height of patient s heart during measurement Do not execute repeated measurements for congestion of blood could result in false measurement Allow the patient s arm to rest for at least 5 minutes Memory Function Measured result obtained in AUTO mode is automatically saved in the memory and can be recalled until next measurement is taken The result is not saved when the measurement is performed in MANUAL mode To recall the result turn on the device by pressing I side of MAIN POWER SWITCH and set the device to AUTO with MODE SELECTOR Press SET MEMORY button and the last result from AUTO measurement is displayed Turn off the device by pressing O side of MAIN POWER SWITCH The device will be in the energy saver mode approximately after 1 3 minutes if it is not turned off See page 10 POWER MARK Error Displays and Troubleshooting ERROR SYMBOL SYVPTOM CAUSE REMEDY OVER PRESSURIZATION The cuff was inflated to the maximum pressure because of movement of body etc Err 300
18. f is inflated automatically after zero settings Pressurization stops when pressure reaches the preset pressure value and rege pressure starts to descend Heart mark flashes in the segment LCD synchronizing detected pulse Deflation rate is displayed at the lower right corner of the segment LCD IR a 2 Press START STOP button whenever the measurement addon tate should be interrupted mmHg s The device will stop during any course of measurement procedure and rapidly exhaust air from the cuff Air is rapidly exhausted from the cuff as measurement completes Blood pressure and pulse rate are displayed Turn off the device by pressing O side of MAIN POWER SWITCH The device will go to the energy saver mode after approximately d LJ 3 minutes if it is not turned off See page 10 POWER MARK Make sure your patient is relaxed has taken at least 5 minutes of rest before measurement and refrains from talking or moving during measurement Confirm that the cuff is kept at the height of patient s heart during measurement Do not execute repeated measurements for congestion of blood could result in false meas urement Allow the patient s arm to rest for at least 5 minutes Taking Blood Pressure Manual Mode When you want to take your patient s blood pressure using the auscultatory method with a stethoscope set the device to MANUAL mode Turn on the device by pressing I side of MAIN POWER SWITCH M
19. ife Life of the rechargeable NiMH battery is approximately 2 years However it may vary de pending on operating conditions Replace the battery when BATTERY MARK is displayed often or when frequent charging of the battery becomes necessary G Tips on prolonging the battery life UE The device is powered by the AC ADAPTER when it is connected d the installed battery is not used if the AC ADAPTER is connected L4 e Remove the battery when operating the device with the AC ADAPTER for an extended period of time or when the battery does not need to be charged e Avoid charging the battery if it is not completely exhausted Do not forcefully remove the battery or pull out the plugs holding cords and cables Use indicated AC Adapter and the battery only Contact your dealer if they are damaged ly POWER MARK The device goes to energy saver mode when it is left turned on and not operated for approximately 3 minutes The mark will be displayed for an hour and then disappear Make sure to turn off the device by pressing O side of MAIN POWER SWITCH down after each use especially when the device is powered by the battery The device activates from energy saver mode when either START STOP button or SET MEMORY button is pressed It is recommended to activate the device by pressing SET MEMORY button since the device could start inflation if START STOP button is pressed Press START STOP button again and stop inflation if the cuff is not wrapped around
20. imited in duration to the terms of this warranty and in no case beyond the original selling price except where prohibited by law This warranty gives you specific legal rights and you may have other rights which vary from state to state To Register Your Product visit us at www adctoday com register Replacement Parts Component Part No Latex free Model Use Coiled Tubing 4 886N Desk Coiled Tubing 8 885N All Models Cuff amp Bladder Sm Adult 845 10SABK IF All Models Cuff amp Bladder Adult 845 11 ABK IF All Models Female Luer Conncetor 891F All Models Male Luer Conncetor All Models Plastic Connector 9002 2 All Models Rechargeable Battery Pack 9002 5 All Models FOR QUESTIONS COMMENTS OR SUGGESTIONS CALL TOLL FREE 1 800 ADC 2670 OR VISIT WWW ADCTODAY COM FEEDBACK Many ADC instruction manuals are available on our website in other languages at www adctoday com care 2013 ADC All rights reserved No one is permitted to reproduce or duplicate in any form this manual or any part thereof without the expressed written permission of ADC ADC assumes no responsibility for any injury to anyone or for any illegal or improper use of the product that may result from failure to use the product in accordance with the instructions cautions warnings or statement of intended use published in this manual The 9002 e sphyg 2 and Adcuff are trade marks of ADC AMERICAN DIAGNOS
21. ove MODE SELECTOR upward and set the device to MANUAL See page 13 for AUTO measurement MANUAL Set the initial inflation value with PRESET PRESSURE KNOB Details on preset pressure page 13 AUTO i Press SET MEMORY button to confirm and or select the u appropriate deflation rate 100 The deflation rate is displayed at the lower right corner of the segment display The deflation rate can be selected from 2 5 4 5 and 6 5 mmHgs The set deflation rate returns to the default value 2 5 when the 25 device is turned off deflation rate Apply the cuff and stethoscope to the patient s arm in the same manner as the usual auscultatory method Press START STOP button The cuff is inflated automatically after zero settings Pressurization stops when pressure reaches the preset pressure value and pressure starts to descend Deflation rate is displayed at the lower right corner of the segment LCD deflation rate NOTE Press START STOP button whenever the measurement mmHg s should be interrupted The device will rapidly exhaust air from the cuff If cuff inflation was not sufficient press and hold down START STOP button once deflation has started and the cuff is pressurized again Pressurization will continue while the button is pressed Pressure does not exceed 290 mmHg Press START STOP button when blood pressure is taken and air is rapidly exhausted from the cuff START STOP Air is also rapidly exhaust
22. t each time The reading is extremely low or high Pulse rate is too low or too high LOW BATTERY Battery is weak BATTERY ERROR Battery is exhausted The indication appearing dur ing LCD segment test which is performed when the unit is turned on does not indicate low battery or battery error ENERGY SAVER MODE The device was left turned on and has not been operated for over approximately 3 minutes When the preset pressure value was not high enough to make measurement or when noise was detected the cuff is pressurized again to a higher level Patient moved during measurement Patient is not being measured with correct posture Blood pressure readings constantly vary with time of measurement and physical and mental condition Patient moved during measurement There was not enough rest taken before measurement Change the battery Only a few measurements can be made before the battery runs down Charge the battery Measurement cannot be conducted Turn off the device or press START STOP button or SET MEMORY button to activate the device from energy saving mode Make sure to turn off the device by pressing 0 side of MAIN POWER SWITCH after use This does not indicate a problem Make sure that the patient stays still and quiet during measurement Make sure that the patient is being measured with correct posture Make sure that the patient stays still during me
23. under dialysis therapy or on anticoagulant antiplatelets or steroids could cause internal bleeding Warning Do not use cuffs AC adapters or batteries other than those included with this product or replacement parts supplied by the manufacturer Warning This system may fail to yield specified measurement accuracy if operated or stored in temperature or humidity conditions outside the limits stated in the specifications section of this manual Warning When using with an infant or child cuff extra care must be taken to prevent over inflation To prevent discomfort or injury to the patient ensure preset pressure is not set above the desired level Warning This product may contain a chemical known to the state of California to cause cancer birth defects or other reproductive harm Caution Federal law restricts this device to sale by or on the order of a physician or licensed healthcare practi tioner Caution To avoid any possibility of accidental strangulation keep this unit away from children and do not drape tubing around your neck Note To obtain the greatest accuracy from your blood pressure instrument it is recommended that the instru ment be used within a temperature range of 50 F 10 C to 104 F 40 C with a relative humidity range of 15 90 non condensing Note All connectors and inflation system should remain connected to the device during storage to avoid dust entering through the connector port Produ
24. ygmomanometers The 9002 digital ADC9 e sphyg 2 sphygmomanometer has the ability to function ac cording to its specifications in the presence of common arrhythmia such as atrial or ventricular premature beats or atrial fibrillation Warnings and Precautions Warning A warning statement in this manual identifies a condition or practice which if not corrected or discon tinued immediately could lead to patient injury illness or death Warning If luer lock connectors are used in the construction of tubing there is a possibility that they might be inadvertently connected to intravascular fluid systems allowing air to be pumped into a blood vessel Immediately consult a physician if this occurs Warning Do not allow a blood pressure cuff to remain on patient for more than 10 minutes when inflated above 10mmHg This may cause patient distress disturb blood circulation and contribute to injury of peripheral nerves Warning Safety and effectiveness with neonate cuff sizes 1 through 5 is not established Warning For all blood pressure systems that can be wall mounted ensure that the unit is securely mounted prior to use to avoid damage to the instrument and potential patient injury Warning Do not use the 9002 in an explosive environment such as where flammable anesthetics exist or inside an oxygen chamber with strong electrostatic and electromagnetic fields e g mobile phones Warning Use of this instrument on patients
Download Pdf Manuals
Related Search