2.4GHz WIRELESS DATA TRANSCEIVER USER MANUAL
Contents
1. close 802 11 a b g AP router and other 2 4GHz devices Pairing procedure 1 Make sure these two devices one is set to Master and another is Slave 2 Please hold the Pairing KEY of the master device until the device connected to DC12V power supply and then you can find the Pairing LED of master device is flashing 3 Please do the same procedure as step 2 again for the slave device 4 When the pairing procedure is complete the RF Link LED of two devices is on 2 Caution for Installation 2 1 Be careful never let any water in this equipment 2 2 f necessary use a soft cloth moistened with alcohol to wipe off the dust 2 3 Be extra careful not to shake the unit 2 4 Avoid places where temperatures exceed 55 C or higher 2 5 Avoid places where there are frequent vibrations or shocks 2 6 When any abnormalities occur make sure to unplug the unit and contact your local dealer 3 Packing 3 1 Transceiver x2 3 2 Antenna x2 3 3 User manual x1 3 4 Screws x8 3 5 Plastic Conical Anchor x8 3 6 Power Adaptor x2 Option 4 Specification RS485 2 wire RS485 Half Duplex Data Baud Rate 2400 4800 9600 bps Fixed Format 1 Start bit 1 Stop bit 8 Data Bits No Parity ALARM I O ALARM Output NC COM NO Dry Contact Contact Rating AC 125V 0 5A DC 24V 1A Storage Temperature 30 C 85 C Dimensions W x L x H 92 x 75 x 25mm 3 62 x 2 95 x 1 00 excluding connectors and witho2. 2 4GHz WIRELESS DATA TRANSCEIVER USER MANUAL MODEL 15 2400RSK Panel View O 2 4G PTZ Controller with Frequency Hopping DC 12V IN BAUD O O O master ERS POWER RS485 ANT PAIRING KEYBOARD CAMERA inati RF LINK Ba PAIRING KEY DVR Termination R5485 ALARM IN o 4 T 1 DC 12V IN DC 12V Power Input 2 BAUD RATE and TERMINATION Baud rate and 120 Ohm termination setting by DIP switch Note After changing the baud rate by DIP switch please re boot the device again Baud Rate Setting On t 2400 bps T 4800 bps 3 RS485 PORT 2 wire Half Duplex RS485 support 4 ALARM IN TTL CMOS digital Input which could be connected to alarm sensor or digital control signal e g Magnetic Reed Switch Detector 5 ALARM OUT Reed Relay Output NC COM NO that could be connected to alarm devices e g Siren Flashing Unit 6 POWER ON or RF LINK LED Indicated to power on or RF link status Power RF LINK LED On RF Link Loss Low Flashing 7 RS 485 or PAIRING LED Indicated to RS485 data are transmitted or received and waiting pairing status Power RF LINK LED RS485 High Flashing Waiting Pairing Low Flashing 8 PAIRING KEY To set the device into pairing mode Please do the pairing procedure before connecting the devices to RS485 network Pleas refer to the pairing procedure for more detail 9 MASTER or SLAVE For RF pairing only 10 ANT SMA connector for connected to 2 4 GHz antennas REMARK Don t
3. fications including the antennas made to this device that are not expressly approved by the manufacturer may void the user s authority to operate the equipment Q2011 04 19
4. ut antenna FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body 3 Any changes or modi
Download Pdf Manuals
Related Search