Write-Once CD-R System User`s Manual
Contents
1. Program Area Empty e No EFM at search address e Link Area Encountered e Calibration Area Full e Dummy blocks added e Block size format conflict e Current Command Aborted BARCODE READING ERROR e Recovery Needed e Can t Recover from track e Can t Recover from Program Memory Area e Can t Recover from Lead in Area e Can t Recover from Lead out Area e Laser Current Over WRITE ONCE CD R System User s Manual2. R Recording Unit Sn ntnnnaln ni nude CD R Image Transmission Error ss CD R Recording Unit Setting Errors ss Errors Returned by CD R Recording Unit ss WRITE ONCE CD R System User s Manual This page was blank in the original Japanese document Introduction Segacdw is a program that records a CD image file created on a virtual CD system command VCDBUILD on a CD R disc using a CD R recording unit This com mand is invoked from the system command prompt WRITE ONCE CD R System User s Manual 3 Installation Hardware Installation Connect the YAMAHA CDE CDR100 CD R recording unit CDE100 is the model name for CDR100 with the system case to the host machine using the SCSI interface See the CDR100 manual for details and how to connect the recording unit Setting CDR100 SCSI ID to 5 eliminates the necessity of setting the SCSI ID to the command segacdw argument each time Software Installation Copy the segacdw execution file from the floppy disk distribution medium to the hard disk of your host machine Set the PATH if necessary Command Reference The CD Witer Command Command name segacdw Syntax segacdw i s t image _prefix Description This command writes to a CD image file a CD R using YAMAHA s CDR100 CD R recording unit The command is invoked from the system command prompt Arguments The name of the CD image file is specified to the image_prefix image_prefix The name of CD image file
3. e Error Number d at Logical Block Address e No Additional Sense e Caddy out e Drive Not Ready e Communication Failure e Track Following Error e Unrecoverd Read Error e Positioning Error e Recovered Read Data With Retries e Recovered Read With ECC Correction e Parameter List Length Error e Invalid Command e Invalid Block Address e Illegal Field in Command Descriptor e Invalid LUN e Invalid Field Parameter List e Medium Changed Power on Reset or Bus Reset Occurred e Command Sequence Error e Medium Format Corrupted e Write Data Error with CU e Monitor Atip Error e Invalid Bits in Identify Message e Diagostic Failure e Power On or Self Test Failure e Internal Controller Error e SCSI Parity Error e Write Operation in Progress e Medium Caddy Load or Eject Failed e Unable to Read TOC PMA or Subcode e Operator Medium Removal Request e End Of User Area encountered on this Track e Illegal Mode for this Track e Illegal Track Command Currently Not Valid e Medium Removal Is Prevented e Stopped on Non data block e Invalid Start Address e Attempt to cross track boundary e Illegal Medium e Application Code Conflict e Ilegal block size for command e Block size Conflict e Request for Fixation Failed e End Of Medium Reached e Illegal Track Number e Data Track Length Error e Buffer Under Run e Illegal Track Mode e Optimum Power Calibration Error e Calibration Area Almost Full e Current
4. incorrect or outdated information while reading through the attached document or come up with any questions or comments please let us know so that we can make the required changes in subsequent revisions Simply fill out all information below and return this form to the Developer Technical Support Manager at the address below Please make more copies of this form if more space is needed Thank you General Information Your Name Phone Document number ST 201 B 092994 Date Document name WRITE ONCE CD R System User s Manual Corrections Questions comments Where to send your corrections 415 802 1440 Mail SEGA OF AMERICA Attn Sr Coordinator Attn Sr Coordinator Technical Publications Group Technical Publications Group 130 Shoreline Dr Redwood City CA 94065 WRITE ONCE CD R System Users Manual Introduction Msn ri nn ae rs Ni daa eh das RR Installation tent AE 200 Hardware Installation ennn on a a a a a e e E e RGA Sofiw agsia lla ON a r a eax MATE tee ESS Command KEren iee a enea SR S N lt nie The CD Writer Command o c ccccccceccesscssccsscssecsecssscsecsscsscsscesscsssesscessesssessesssessesascasssassass The TOC File Generator Command miss iii Troubleshooting ss Image File saine RU Ann aei aeae Rens E EE RE RE have HPF ormat Errors nie aav eaan int TAR tee A EA Error ennemi nent Cue Sheet Errors Sas AE AA OS EN Sn RAR A En darts Errors Generated by the Relationship between the Host Machine and CD
5. is the prefix of files which have the dsk the emu and the toc file name extensions These files must all be in the same direc tory The CD image files created with the Virtual CD System should have the file name extension dsk Use the file name extension emu for the CD image files created with the C Trac Builder Options i Specifies the distination to be transmitted the CD image files by the SCSI ID 0 to 7 In other word specify SCSI ID of CDR 100 The default is 5 S Specifies the writing speed Specify any one out of the values 1 normal speed 2 double speed and 4 quadruple speed The default is 4 which writes at quadruple speed t Write with CDR100 test mode The actual CD R is not written on it Examples To record a CD image file consisting of test dsk and test toc onto a CD R specify as follows C gt segacdw test The following is the test to record at double speed on a recording unit with a SCSI ID of 6 C gt segacdw i 6 s 2 t test WRITE ONCE CD R System User s Manual 5 The TOC File Generator Command Command name gentoc Syntax gentoc v image_prefix Description This command generates a TOC file from a CD image file created using C Trac Builder for MEGA CD SEGA CD The command is invoked from the system prompt Arguments The name of the CD image file is specified at an image_prefix image_prefix The CD image file name is the prefix of a file which has the an emu file name ext
6. result from applications based on the examples describe herein It is possible that this document may contain reference to or information about SEGA products development hardware software or services that are not provided in countries other than Japan Such references information must not be construed to mean that SEGA intends to provide such SEGA products or services in countries other than Japan Any reference of a SEGA licensed prod uct program in this document is not intended to state or simply that you can use only SEGA s licensed products programs Any functionally equivalent hardware software can be used instead SEGA will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user s equipment or programs according to this document NOTE A reader s comment correction form is provided with this document Please address comments to SEGA of America Inc Developer Technical Support att Evelyn Merritt 150 Shoreline Drive Redwood City CA 94065 SEGA may use or distribute whatever information you supply in any way it believes appropriate without incurring any obligation to you 11 2 94 002 SEGA SEGA OF AMERICA INC Consumer Products Division WRITE ONCE CD R System User s Manual Doc ST 201 B 092994 1994 SEGA All Rights Reserved READER CORRECTION COMMENT SHEET Keep us updated If you should come across any
7. General Notice When using this document keep the following in mind 1 This document is confidential By accepting this document you acknowledge that you are bound by the terms set forth in the non disclosure and confidentiality agreement signed separately and in the possession of SEGA If you have not signed such a non disclosure agreement please contact SEGA immediately and return this document to SEGA This document may include technical inaccuracies or typographical errors Changes are periodi cally made to the information herein these changes will be incorporated in new versions of the document SEGA may make improvements and or changes in the product s and or the program s described in this document at any time No one is permitted to reproduce or duplicate in any form the whole or part of this document without SEGA S written permission Request for copies of this document and for technical information about SEGA products must be made to your authorized SEGA Technical Services representative No license is granted by implication or otherwise under any patents copyrights trademarks or other intellectual property rights of SEGA Enterprises Ltd SEGA of America Inc or any third party Software circuitry and other examples described herein are meant merely to indicate the character istics and performance of SEGA s products SEGA assumes no responsibility for any intellectual property claims or other problems that may
8. e Sheet parsing failed e Cue Sheet conversion failed e Cue sheet size error e Cue sheet too large e Empty cue sheet e No track definitions in cue sheet Can t find lead out in cue sheet e Nocore for cue sheet The following error message indicates that there is not a Cue Sheet generated or there is not a file that contains the Cue Sheet not in the same directory as the image file No cue sheet WRITE ONCE CD R System User s Manual 7 Errors Generated by the Relationship Between the Host Machine and CD R Recording Unit CD Image Fansmission Error The following error message indicates that the I O speed of the host hard disk cannot keep the same the writing speed as of its CD R writing unit Specify the correct speed using option s Buffer Under Run CD R Recording Unit Setting Errors The following error message is displayed when an incorrect writing speed was specified Specify the correct writing speed using the option s e Error Bad speed value The following error message is displayed when the CDR100 firmware version of the is old and cannot create CD discs for SEGA Saturn Change to the correct version of the CDR100 firmware e Firmware upgrade of CD recorder is needed to use this software Errors Returned by CD R Recording Unit The following error messages are returned by the CD R recording unit e Unknown sense key Unknown additional sense code e Field Replaceable Unit failed Number of Errors
9. ension Options v Displays such information as the contents of the Cue sheet Example To generate TOC file test toc from test emu specify as follows C gt gentoc test Troubleshooting The following sections describe the measures against the error message display Image File Errors The error messages described in this section will be displayed when there are prob lems with the CD image Make sure the dsk file or the emu file is in the same directory as the toc file Make sure the files are created correctly using the Virtual CD System If the error still remains you will have to create the CD image again Image File Format Errors The following error message displays indicate that the format of the CD image to be recorded is incorrect e Bad data form unknown data form in line e Error Data Length The following error message display indicates either the mode of the CD ROM to be created is incorrect or a CD image format is not supported by segacdw Unknown data mode ISRC Length Errors The following error message display indicates that there is a problem with the length of the ISRC stored in the CD image Check the original data and regenerate the CD image ISRC length error in line Cue Sheet Errors The following error message display indicates that there are problems with the Cue sheet Recreate the dsk file and toc file using the Virtual CD System e Cue Sheet intermediate conversion failed e Cu
Download Pdf Manuals
Related Search