Home

Manual Leapfrog Creatr

1. Infill Percentage 1 15 IndudeRaft W Generate Support Leapfrog BV Manual Leapfrog Creatr If you want to adjust more settings than just the options that are given in the basic FFF Settings menu you click Show Advanced to show the advanced print settings Now that the model has been imported and the process created we can create the g code to control the printer This is done by clicking Prepare to Print in the processes menu You will have to select a location to save the g code A g code is now being created to print your model This may take a few minutes When the slicing finishes the software will open the G code file for previewing It is advised to always check the preview to make sure the slicing went correctly and as desired It may take a short while to open the preview in the 3D display When you have verified that the g code has been created as desired and want to start the print on your Creatr you can start the print by clicking Begin Printing over USB and your print job will start If the preview is not as desired or displays a mistake you can go back by clicking Exit Preview Mode Leapfrog BV ee Leapfrog Manual Leapfrog Creatr 7 e Begin Printing over USB Save Toolpaths to Disk d Exit Preview Mode NB Don t forget to preheat the extruder s and the heated bed This will save you time and manually extruding a bit o
2. PLA ABS PVA Nylon Medium High General Settings Infill Percentage tJ 3 SS o Indude Raft Generate Support Indude Skirt Brim Skrtlayers 1 t Skirt Offset 0 00 2 mm Skirt Outlines 10 E o Temperature heated print bed If your print does not remain on your print bed while printing you could increase the temperature of your bed When you use PLA or PVA filament we advise you to start with a bed temperature of 60 C If you are still experiencing warping problems set this temperature to 65 70 C For ABS or Nylon we advise to start with a bed temperature of 80 C You could increase this to 85 90 C If you are printing with multiple filament types at the same time please make sure that your bed is set to the temperature for the filament that requires the hottest bed Leapfrog BV T Manual Leapfrog Creatr Leapfrog Check the Z offset If your object won t stick to the bed it is possible that the Z offset is too big and you need to decrease the Z offset Placing the bed a little bit closer to the nozzle will result in better adhesion between the first layer and the heated printbed Since the print sticker is made of plastic the first layer and print sticker can melt together If the Z offset is incorrect then you can follow the steps in section 3 13 That section explains the procedure thoroughly Leapfrog BV Manual Leapfrog Creatr 3 3 Extruder stops in mid p
3. Manual Lreatr the Future T Manual Leapfrog Creatr Leapfrog Dear customer Congratulations with the purchase of your very own Leapfrog Creatr Single or Dual Extruder We would like to help you get started so you can make your first 3D print on the Creatr and many more This is why we have developed this document it will guide you through unpacking installation and the print settings We also provide you with guidelines to get you back on track if something should go wrong It is possible that after reading this document or while operating your printer you have a question that is not listed in this document Therefore we also explain you how to contact our support department We wish you happy printing With kind regards The Leapfrog team 2 Leapfrog BV T Manual Leapfrog Creatr Leapfrog 3 Leapfrog BV Th Leapfroq Manual Leapfrog Creatr Table of content 4 Leapfrog BV 1 Installation 1 1 Unpack 1 2 Voltage switch 230 V gt 115 V 1 3 Software 1 4 Connect 2 Printing 2 1 Print sticker and Kapton tape 2 2 Connection 2 3 Preheat 2 4 Manually controlling your printer 2 5 Filament 2 6 Print settings 2 7 Printing with PVA 2 8 Start your print 2 9 When your print is finished 2 10 More information and tutorials 3 Troubleshooting Knowledgebase 3 1 Oh oh my filament is not feeding through 3 2 My object won t stick to the bed 3 3 Extruder stops mid
4. o Select the category which best suits your question o Select the priority of your question o Next please describe your question as detailed as possible so our support team can answer you as best as possible o Clarifying your question with pic s and movies will significantly increase the speed of providing a clear answer you can add files below Attach a file You will receive an automatic email when your ticket has been updated This way you do not have to check if you have received an answer but we will let you know Ps Leapfrog Dashboard My Tickets Add a new ticket Knowledgebase 3D Printers Store Support new ticket Please be descriptive and provide demonstrative links where possible You will be notified when a member of our support staff updates your ticket Ticket Title Enter a one line summary Type 1 General inquiries Describe the problem lescribe the problem including detail Attach a file No file select Choose File Priority gt low add ticket Leapfrog BV e Manual Leapfrog Creatr Leapfrog Appendix A Troubleshootingtrees When you run into a problem when using your printer but are not sure what is going on it can be hard to find the solution in the user manual To ease this process and help you find a solution as soon as possible we have created troubleshootingtrees for some problems that will direct you to the solution or refer to the location of t
5. clogging If you see that the fans are not spinning try to give them a push with for example a pen to get them going If they still don t start spinning please check if the wiring is connected properly 48 Leapfrog BV T Leapfroq Manual Leapfrog Creatr Heat cartridge Check whether the heat cartridge is sufficiently centred in the heat block In the pictures below you can see a heat cartridge that is centred and one that is not It is important that the heat cartridge is centred properly so that the heat is distributed equally over the filament and that the thermistor reads the correct temperatures preventing too cold extrusion which can cause clogging If you see that the heat cartridge is too far outside the block please loosen the index bolt that holds it and adjust the position Correct Centred Wrong Not centred Nozzles Check if the nozzles are still hot after the extruder stops and if they have the correct temperature Do not check this with your bare hands the nozzles can be very hot Please look at the software for the current temperature If the nozzle heating is somehow turned off or a different temperature was set this will result in clogging due to cold extrusion It is important to check if the software is set at the correct temperature Driver gear Check if the driver gear is tightened to its motor correctly If the driver gear is not tightened correctly the motor will deliver power
6. computer to connect with the printer Th step isto download and e For Windows 8 follow the Windows instructions mentioned later in this step Download Arduino 1 0 5 ZIP file Open the file with an archive utility like Winrar or WinZip Download Next steps Arduino 1 0 5 release notes hosted by Google Code Getting Started Reference Windows Installer Windows ZIP file a Environment MacOSX E ples Linux 32 bit 64 bit 5 source FAQ Leapfrog BV ER Manual Leapfrog Creatr Leapfrog e Unpack the content to any location DET Gv Tools Favorites Options Help E A Ld View Delete Find Wizard Info Virusscan Comment Name Size Packed Type Modifie di z Bestandsmap arduino 1 0 5 Bestandsmap 17 5 a e Go back to www lpfrg com support installation and on the website click on the text Leapfrog Repetier software to download Repetier Host Leapfrog setup from the website The first step is to download and install Arduino software to make it possible for your computer to communicate with your printer The next step is to download the Leapfrog Repetier Software as shown in the video This software allows you to convert your 3D software file STL for example to a printable file G Code and allows you to control your printer The Leapfrog Repetier software contains standard Creatr Print Profiles Just select the extruder the Leapfrog BV Manual Leapfrog Creat
7. filament spool from the printer Leapfrog BV Manual Leapfrog Creatr 2 6 Print settings To fully understand the print profiles it is best to first explain certain settings involved in the printing process Support material General explanation Support material is added during the printing process in order to support the overhanging parts of your design Not all shapes need support material For example the left cup you see below can be printed without support material because all layers can be easily printed on the layers below However the cup on the right is not printable without support because the printer cannot print the ear part into thin air If you would print this design without support material the print material will just drop down on the place where the ear begins In this case you will need to print your object using support material When printing with support material there is no need to design the support structure yourself the software will automatically calculate this for you when selecting one of the support profiles Breakaway support There are two types of support Breakaway support and Soluble support Breakaway support is a support type that adds support material in the same material and color as the material you use to print your object Here the support material is printed with one and the same extruder Therefore this type is great for those owning a Creatr Single extruder When
8. high quality printing and medium quality printing With 3D printing you will always ask yourself Do need a quick prototype or the final product The answer to this question affects your choice for the print process High quality printing Choosing for high quality will give you the best results This will mean that the layer height of each layer is very small 0 15 mm leaving an almost flat finish When selecting a high print quality your layers become almost twice as small compared to the medium printing setting This will result in more movements needed by the print head and therefore it also takes twice as much time to print your object Also there will be more infill by default increasing the print time but creating a stronger print You can adjust the infill by hand after selecting the quality of your print Medium printing also known as fast printing When you need a very quick prototype just to check dimensions of your product or to quickly show someone the idea we would recommend the fast printing profile The fast print profile prints with a layer thickness 0 25mm Here you will notice a less smooth finish surface but choosing the fast printing profile will also speed up the print time about twice Leapfrog BV T Manual Leapfrog Creatr Leapfrog 2 7 Printing with PVA Preparing the extruder e If you have previously used your extruder with another filament type and you want to start using PVA Mak
9. print 3 4 Min max temp triggered error messages 3 5 Nozzle seemed clogged 3 6 My extruders are not the same height 3 7 Uploading firmware 3 8 My STL file contains a hole and needs to be fixed 3 9 Calibrating the heated printbed 3 10 Z height does not match model 3 11 Checking the size of your z axis pulley 3 12 Adjusting the z offset 3 13 Checking the internal usb cable 3 14 Need support Page 7 Page 10 Page 11 Page 17 Page 20 Page 24 Page 25 Page 27 Page 29 Page 33 Page 35 Page 36 Page 41 Page 42 Page 44 Page 45 Page 48 Page 56 Page 59 Page 63 Page 64 Page 68 Page 69 Page 70 Page 71 Page 72 Page 74 Page 76 T Manual Leapfrog Creatr Leapfrog Appendix A Troubleshootingtrees 1a cannot connect my printer Page 79 1b Firmware Page 80 2 Calibration Page 81 3 My printer makes a lot of noise Page 82 4 Temperature errors Page 83 5 Extruder jams Page 84 6 Print doesn t stick to the bed Page 85 7 Printer loses connection during print Page 86 8 My print bed doesn t heat up Page 87 9 My print looks bad Page 88 5 Leapfrog BV Manual Leapfrog Creatr 1 Installation The following steps are steps you only have to follow when your brand new Creatr arrives at your doorstep for the first time Please follow each step thoroughly to make sure the installation will be a success and you can find yourself as a member of the Leapfrog eco system This section contains the followin
10. support Ipfrg com Leapfrog BV
11. the e mail address you ordered the software with The software is distributed via an electronic download e If you follow the link you will have to enter the product key and select the operating system that your computer runs on and click the download software button to start downloading the software Please not that you can download the software for only one computer using one product key Enter Product Key Operating System See n m Download Software e Now that you have downloaded the installer you can run it to install the actual software on your computer At the end of the installation wizard you will be asked to open the Quick start guide We recommend you to open and read this file as it provides a great insight in all the features of the software You can save the file or access it later from the software via Help gt Quick Start Guide e Before you can start using the software you will have to activate it This can be done via Help gt Activate Product A window will pop up where you will have to enter the product key in order to activate the Simplify3D software and start printing Leapfrog BV ER Leapfrog Manual Leapfrog Creatr e On the website click on the text Arduino software Operating system Windows miare oig D gt C Boe nmi cmt com o Frm ooootroq ca Kien The first step is to download and install the Arduino software to make it possible for your
12. 0 degrees for PLA and PVA You can also check the temperature by looking at the temperature plot see next screenshot The red dotted line is the setpoint for the extruder and the red solid line is the actual measured temperature The blue lines mean the same but for the bed instead of the selected extruder Leapfrog BV e Manual Leapfrog Creatr Leapfrog Temperature C Monitor Temperatures Clear Plot Data Leapfrog BV T Manual Leapfrog Creatr Leapfrog 2 4 Manually controlling your printer This section of the manual will explain you how to control the axes of your printer and extrusion using the manual controls of the printer e Manual controlling in the Simplify3D software is done using the jog controls tab in the machine control panel e Clicking these buttons will make your printer perform the associated operation All the numbers written on the buttons represent the amount of mm For example clicking the 100 button in the Y direction will move the extruder carriage 100mm in the y direction i e to the back of the printer Leapfrog BV Manual Leapfrog Creatr The extrude and retract buttons will extrude and retract filament for the selected extruder Please note that this can only be done when the extruder is heated The home buttons will move the axes to the home position The home position is the point where the coordinates for the axes are 0 You can home each a
13. GNU General Public License for more details You should have received a copy of the GNU General Public License along with this program If not see http www cqgnu ormg licenzse Arduino Wega 2560 of Wega ADK on COMME e Once the firmware has been successfully uploaded you can close the menu and all is set for you to start printing Leapfrog BV b Manual Leapfrog Creatr Leapfrog 3 8 My STL file contains a hole and needs to be fixed It is possible that Repetier Host Leapfrog provides you with an error that your STL file contains a hole This means that your file is not complete and when you print your file there will be a gap in your print where Repetier Host Leapfrog noticed there is a hole in your file Overall it is difficult to figure out where the hole is located This is where we can recommend using the Netfabb Cloud Service Netfabb Cloud Service is a service that checks your file and repairs it free of costs Please follow the guidelines below to fix your file e Goto http cloud netfabb com 9 2 E vjetrabb Buy Case Studies Products v Community Media Contact v Software for 3D Printing j 1544 UN fi H ni iid 4 em AL f i i netfabb Cloud Service Beta Web based file processing analyze check and repair your STLs The netfabb Cloud Services offer a free and easy to use solution for anyone with access to an internet conne
14. Leapfrog BV m Manual Leapfrog Creatr Leapfrog e Insert the power cord and USB cable in the backside of the Creatr e Plug the power cord in the outlet the USB cable in your computer and turn on your Creatr NB Make sure that you connect the power cord to a grounded outlet 9 Leapfrog BV Ps Manual Leapfrog Creatr Leapfrog 1 2 Voltage switch 230 V gt 115 V This step is only necessary if your electrical grid provides 115V WARNING NEVER PERFORM THIS OPERATION WHEN THE POWER PLUG OR USB CABLE IS PLUGGED INTO YOUR CREATR e Ifyou already connected your Creatr to your computer and power grid unplug your power cord and USB cable e Tilt your Creatr so you can access the bottom Look for the square hole e inthis hole you can see a yellow sticker and under it a red switch e Use an Allan key or screw driver to carefully move the switch to the left Your Creatr now operates on 115 V WARNING NEVER PERFORM THIS OPERATION WHEN THE POWER PLUG OR USB CABLE IS PLUGGED INTO YOUR CREATR Leapfrog BV Ps Manual Leapfrog Creatr Leapfrog Here we will explain you where to download and install the necessary software that communicates to your printer and turns your design into a printable file Download and activation e After you receive you have purchased the software you will receive a product key and a download link which is http www simplify3d com downloads at
15. Manual Leapfrog Creatr Leapfrog 3 10 Z height does not match model When your printed object turns out to be substantially larger or smaller than your originally model digital model it could be that your printer is equipped with incorrect firmware and therefore takes to many steps on the z axis each new layer A characteristic of this problem is that it becomes worse the higher the model is This guide will explain you how to resolve this problem e To determine what firmware your printer requires please check the troubleshootingtree Firmware in Appendix A This will automatically lead to the correct firmware to be loaded onto the electronics board e Now that you have found out what firmware you need Please contact support via a ticket at support lpfrg com and explain why you want the new firmware and what firmware you need according to the troubleshootingtree Section 3 7 explains how to upload this firmware onto your printer Leapfrog BV n T Manual Leapfrog Creatr Leapfrog In order to provide you with the correct firmware for certain models our support team needs to know the diameter of your z axis pulley If the firmware troubleshootingtree has led you here this paragraph will explain you how to check the size so that you can let support know e The pulley that you want to check is located in the back of the printer underneath the electronics cover The easiest way to check this would be to remove the back pla
16. Remove the old print sticker or Kapton tape and clean your print bed e Carefully align the Kapton tape as shown in the picture below Secure the tape by pressing down a small bit of the tape on the print bed while pushing the roll of tape to tense the tape Leapfrog BV T Manual Leapfrog Creatr Leapfrog e Hold the roll so the unapplied tape remains tense press the tape down by sliding 2 3 fingers from side to side or use an old bank card Leapfrog BV T Manual Leapfrog Creatr Leapfrog 2 2 Connection In order for your computer to tell your printer what to do you will need to connect your computer to your printer In this step we will show you how to do this with the Simplify3D Software e To connect and control the printer in the Simplify3D software you will need to access the machine control panel You can do so by either clicking the gear at the right side of the software interface see screenshot below or using Ctrl P ia Li ie Machine Control Panel e Now that you have opened the machine control panel you have to select the port that the printer is connected with and set the baud rate to 115200 Once you have set these you can simply press Connect to establish a connection with your Creatr The connect button should turn green instead of red Initialization oom b Print I ELAZLAL Cr Baud Rate 115200 Jbiskec V verbose e Inthe communication tab y
17. but the driver gear won t spin If this is the case please tighten the screw that is indicated on the picture below Leapfrog BV T Leapfroq Manual Leapfrog Creatr The next steps If all the checks mentioned earlier turn out to be okay we advise you to follow the next steps Clean your nozzle with your filament It is important that the nozzle has no leftover filament inside it that are stuck Please heat the nozzle to 220 230 degrees and retract the filament until it is completely out of the extruder Cut off the last part from the just retracted filament and make sure your cut is perpendicular Heat the nozzle to 240 degrees Celsius feed and extrude the filament Hereby the filament should push any clogging parts through the hot end This is a great way to clean your nozzle without the hassle of removing the nozzle and placing it in a bowl of dissolvent We would recommend doing this on a regular basis when you start your prints as it is a fast and a good regular check Printing at higher temperatures Printing with a nozzle that is too cold can cause clogging This can occur mid print because the nozzle temperature fluctuates with a few degrees If this happens please increase the temperature of your nozzle You can increase the print temperature in the process of simplify3d Click Show advanced and go to the temperature tab There you can select the extruder for which you wish to change the print temperature Remo
18. code A G code is a file format that the printer uses to print All your settings like print material speed layer thickness etc are in the G code Firstly make sure the print bed is heated to the correct temperature for the filament that you will be using It is advised to extrude a bit of filament before you run your print job to make sure that the nozzle isn t clogged Please note that the printbed will automatically move to the Home position when starting a new print The home position is the position where the value for the X Y and Z direction is zero You can see that the bed is placed at the highest point and the extruders are positioned at the front left side of the printbed If you want to print a pre existing G code you need to go to the machine control panel see section 3 3 and click Print which can be found next to the connect disconnect button A menu will pop up where you can browse your computer for the g code you wish to print Double click the desired g code and the print job will start Don t worry if the extruder carriage or bed don t move immediately after reaching the home position The printer will stabilise the extruder and bed temperature before it starts any movements You can monitor this process in the communication tab Leapfrog BV T Manual Leapfrog Creatr Leapfrog I have a STL file A STL file is a file format that contains the 3D design of your file If you have a STL fil
19. connect the fan cables Slide away the front of the carriage Leapfrog BV T Manual Leapfrog Creatr Leapfrog o Step 2 Loosening the bearing plate The plate where the bearing is attached to is fastened with two bolts as shown in the pictures below Loosen these bolts a little to be able to change the distance between the driver gear and the bearing Do not take them out o Step 3 Checking the driver gear Now is a good time to check if the groove of the driver gear is neatly in line with the entry of the hot end tube The left picture displays a good alignment the middle picture displays a misaligned driver gear Here the green lines should be on top of each other If your driver is misaligned please loosen the small index bolt see right picture and slide the driver gear on the axis of the motor to the correct position Don t forget to tighten it again SAALIIN DINE I ZW 1 n Leapfrog BV e Manual Leapfrog Creatr Leapfrog o Step 4 Determine the proper distance of the bearing Grab a drill with a diameter of 1 5mm or anything else with this diameter and stick it on the hole of the hot end tube It should also be positioned against the groove of the driver gear Next place the bearing plate in such a way that the bearing is tight against the drill bit Then tighten the two bolts holding the bearing plate in order to fixate the bearing o Step 5 Testing Now that you have adjus
20. ction and a web browser netfabb Cloud Services works for multiple platforms and operation systems including Windows Linux and Mac OS STL File Bestand kiezen Geen bestand gekozen Email adress Units 9 mm inch E accept the terms and conditions mentioned below Imm Please make sure to use a valid address The results will only be available in your email 55 du e Upload your STL file enter your email address and the units you are using mm or inch and submit your STL file Netfabb will check and repair your file and send it back to you by mail Leapfrog BV T Leapfroq Manual Leapfrog Creatr 3 9 Calibrating the heated printbed e To calibrate your heated bed bring your bed to the Z home postion and make sure that your nozzles are at the same height If they are not please check paragraph 3 6 to level the extruders e To make sure that your heated printbed is correctly calibrated again you need to send the nozzles to the four corners of your heated printbed using the X and Y buttons X A e n each corner you need to see the same distance between the nozzles and the heated bed You can adjust this by un screwing the bolts that hold the bed in the corner a little as shown in the picture below Once the distance is the same at every corner check the z offset as explained in par 4 2 and you are ready to print Leapfrog BV T
21. d then retract the filament If the bearing is too far away from the driver gear you will hardly see any marks on your retracted filament If this is the case you will need to change the distance between the driver gear and the bearing If the gear is a little bit too close to the driver your filament will be deformed too much see the figure below This causes the filament to be unable to pass through the hot end properly and it will jam The following description explains how to change the distance between the driver gear and the bearing Un used Extruded Too far away Correct Too close Figure Sketch of the filament for three types of distances between the driver gear and the bearing Left shows when they are too far apart The middle shows the correct distance and the right sketch displays the filament when the distance is too small Leapfrog BV Manual Leapfrog Creatr Leapfrog o Step 1 Gain access to the bearing plate In order to gain access to the bearing plate you will have to remove the 2 middle bolts at the front of the extruder carriage first as shown in the next figure Once these bolts are loosened you have to disconnect the connectors of the fan cables in the cable chain so you can slide the front of the carriage sideways Now you gain access to the plate in front of the driver gear This plate can easily be removed by loosening the bolts in the bottom corners of the plate Loosen the middle bolts Dis
22. de a test piece 2 6 Print settings o Which printing settings are there and when to select which one 2 7 Printing with PVA o How to print with PVA and necessary maintenance 2 8 Start your print o Howto start a print using a G code or a STL file 2 9 When your print is finished o What to do when your print job is done 2 10 More information and tutorials o Where to find more information and instructions Leapfrog BV E Manual Leapfrog Creatr Leapfrog 2 1 Print sticker and Kapton tape In order for the filament to stick to the print bed you will need to apply a print sticker or Kapton tape In this section we will explain you how to apply this The print stickers that we supply are easy to apply to the print bed and can easily be removed again Kapton tape is very thin which makes it more difficult to apply to your print bed You will need to apply three rows of Kapton tape to cover the same area as a print sticker However you can print more objects on Kapton tape before replacing it in comparison to the print sticker e Remove your test print from the print bed do not remove the sticker You can use a putty knife to make it easier to remove your printed object If the print still sticks on the print bed turn on the print bed to 40 degrees Celsius in this case please first follow step 2 2 amp 2 3 Heating the print bed can make it easier to remove prints It is easiest to remove prints immediately after finishing prin
23. e you will need to convert it to a printable file format called G code Below the steps to do so are explained e Inthe models section of the Simplify3D software click Import A pop up will open to let you browse for the STL file that you wish to print You can always add another model to print them both in the same print job You can remove a model by selecting it and clicking Remove e When you have imported the model it will appear on the virtual print bed i e the 3D display of the software You can move the model on the bed by holding Ctrl and the left mouse button so that you can drag the model to the desired location You can also click Center and Arrange to have the software automatically center and arrange your objects for you e Once the model is loaded and in the correct place the process will need to be selected to determine the settings for the print job You can do so by clicking Add in the processes menu To remove a process you can select the process and click Delete To edit a process that has already been created select the process that you would like to edit and click Edit Process Settings Leapfrog BV Manual Leapfrog Creatr e The FFF settings menu will pop up see next screenshot FFF stand for Fused Filament Fabrication which is the industry name for the technique the Creatr uses You can rename the process with any name that you find convenient to recognise in the P
24. e sure to generously flush the extruder according to the following steps 1 Heat the extruder 2 Extrude the previously used material 3 Retract the filament and set the extruder to PVA temperature 4 Extrude the PVA until the extruded material is 100 PVA Maintenance There are several maintenance points to be addressed when using PVA In general you should not let the extruder be heated for a longer period when you are not using the Creatr e PVA absorbs moist from the air and will become soft when exposed to long Therefore you should remove the PVA from the machine and place it in a zip bag when not using it e When the PVA gets too soft you can place the material including spool in an household oven Pre heat the oven to 80 degrees Celcius and place the filament inside the oven It may take 6 10 hours to completely evaporate all the water from the PVA However after doing so you will be able to resume printing with the filament the way you are used to Leapfrog BV Manual Leapfrog Creatr 2 8 Start your print This section of the manual will explain you how to print a file if you already have a printable G code or if you start with a STL file STL files are files that contain your design but do not contain the movements the printer needs to make while it is printing This is why a STL file needs to be converted into a G code a file format that tells the printer how to move in order to create your design I have a G
25. ent if necessary e The first things to do is remove both the power and the usb cable from the printer to avoid any power being on the printer Once you have done so you can remove the left side plate by loosening the four screws at the corners as indicated in the picture below e You have now gained access to the Leapfrog electronics board at the side of its usb entrance The internal usb cable is connected to this usb port as shown in the next picture If you would like a better overview you can also remove the electronics cover Leapfrog BV eh Leapfrog Manual Leapfrog Creatr e You have now gained access to the Leapfrog electronics board at the side of its usb entrance If you would like a better overview you can also remove the electronics cover All that remains to do is unplug the internal usb cable from the electronics board and plug in the usb cable that comes directly from your computer running the printer in the electronics board instead of in the back of the printer like you usually would The next picture shows where to insert the external usb e Any signal deviations from the internal usb cable have been removed now so you should run your print again and see what happens If you don t lose connection anymore your internal usb cable is most likely the problem and you can contact support at support lpfrg com for a replacement Leapfrog BV T Manual Leapfrog Creatr Leapfrog 3 14 Need suppor
26. ernet for the latest driver software for your device unless you ve disabled this feature in your device installation settings Browse my computer for driver software Locate and install driver software manually e Select the location of your Arduino files Select the driver map and click Next The printer will now be recognized by your computer Browse for driver software on your computer Search for driver software in this location Include subfolders Leapfrog BV T Leapfroq Manual Leapfrog Creatr Windows 8 driver installation steps Download Arduino 1 0 5 ZIP file Save unsaved work and write the instructions down your computer will reboot into startup options screen Press the Windows Key and the R key simultaneously Copy the command inside the brackets shutdown exe r o f t 00 Select Troubleshoot Select Advanced options Select Startup Settings Select Disable Driver Signature Enforcement Install driver as usual via device manager Leapfrog BV T Manual Leapfrog Creatr Leapfrog In this step we will show you how to connect the printer to your computer e Phyiscally connect the printer to your computer by inserting the usb cable that is connected to your computer in the back of the printer e Open Simplify3D and go to the machine control panel using the button as shown in the screenshot below or CTRL P e Inthe Device manager
27. es cardreader h 21 1 2013 14 54 H bestand Configuration h 21 1 2013 14 54 H bestand L4 _ Configuration adv h 21 1 2013 14 54 l bestand Bureaublad EEPROMuwrite h 21 1 2013 14 54 I bestand jfastio h 21 1 2013 14 54 1 bestand _ lanquage h 21 1 2013 14 54 l bestand Marlin h 21 1 2013 14 54 1 bestand Marlin_gebruikte_dual_M amp ino 21 1 2013 14 54 IO bestand MarlinSerial cpp 21 1 2013 14 54 CPP bestand MarlinSerial h 22 1 2013 16 55 H bestand _ motion_control cpp 21 1 2013 14 54 CPP bestand ERES control h 21 1 2013 14 54 H bestand 4 n Bestandsnaam Marlin gebruikte dual MBino Leapfrog BV T Manual Leapfrog Creatr Leapfrog e The final step is to upload the firmware This is done by pressing the upload button which is indicated by an arrow pointing to the right as shown lighted up in the screenshot below sketch jan22a Marlin gebruikte dual M8 Tr Reprap firmware based on Sprinter and grbl Copyright iC 2011 Camiel Gubbels Erik van der zalm This program is free software you can redistribute it and or mod it under the terms of the GNU General Public License as published the Free Software Foundation either version 3 of the License or at your option any later version This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR amp PARTICULAR PURPOSE See the
28. f filament before running your job will prevent clogging Leapfrog BV T Manual Leapfrog Creatr Leapfrog 2 9 When your print is finished When your print is finished you still have to remove it from the bed and maybe want to create a smoother finish This section explains what to do once your print is finished e The first thing to do when the Creatr has finished building your object is let the bed cool down This is to avoid deformation of the print while removing it from the bed When the bed has cooled down you can carefully remove it from the sticker If the sticker is not torn you can re use it for your next print e The easiest way to remove the object is by lifting the corners first Also a tool such as a putty knife can be of great assistance e If you want a smoother and shiny finish of your object you can print it in ABS and finish the print after you have printed it You can do so by making the surface slightly rougher with sanding paper and then sweep it with a little bit of acetone Leapfrog BV T Manual Leapfrog Creatr Leapfrog 2 10 More information and tutorials In this chapter we have explained the basics of the Simplify3D software so that you are able to make your first simple prints The software however contains many more options and possibilities For example multi colour prints multi material prints manual support defining and many more This section will explain where all extra in
29. formation and specific tutorials can be found e Simplify3D has created a lot of useful tutorials for all the possibilities that the software offers You can find these tutorials on http www simplify3d com support tutorials Please take a look there to find out everything you need to k now about your simplify3D software e Leapfrog is constantly experimenting with new types of filament to add to our assortment of filaments that we sell When we start providing a new type of filament you will need the correct print settings to use it These will be automatically included in the Simplify3D software updates Leapfrog BV ER Manual Leapfrog Creatr Leapfrog Troubleshooting Knowledgebase In this section we provide you with guidelines to get you back on track if something should go wrong Of course it is possible that you encounter something that is not listed here you can then check out our troubleshootingtrees in Appendix A or paragraph 3 16 where we explain what you can do in such a case This section contains the following 3 1 Oh oh my filament is not feeding through 3 2 My object won t stick to the bed 3 3 Extruder stops mid print 3 4 Min max temp triggered error messages 3 5 Nozzle seemed clogged 3 6 My extruders are not the same height 3 7 Uploading firmware 3 8 My stl file contains a hole and needs to be fixed 3 9 Calibrating the heated print bed 3 10 Z height does not match model 3 11 C
30. g 1 1 Unpack o How to unpack your Creatr and where to plug in your cords 1 2 230 gt 115 V o If necessary how to switch your Creatr to 115 V 1 3 Software o How and where to download the necessary software 1 4 Connect o Howto let the computer recognize your brand new Creatr 6 Leapfrog BV fad Manual Leapfrog Creatr Leapfrog In this step we will show you how to unpack your Creatr when it arrives at your doorstep Before you start make sure that you have cleared a spot where you want to place the printer We advise you to not place the Creatr next to a window or at a place where it is draughty e Unscrew all the top screws of top plate of the shipping crate and remove the top plate e Remove the filament you ordered and open the cardboard box Remove the plastic that is placed on top of the printer and take out the printer while holding it as shown in the pictures below It is best to do this with two people Leapfrog BV aS ud Leapfrog Manual Leapfrog Creatr e NB Beware that you don t take out the printer as shown in the next pictures Your printer can lose calibration when picking it up incorrectly Do not lift your printer out of the box by the top plate or any of the axes Do not lift the printer by the cardboard box e After positioning the printer on the desired spot remove all plastic that is used to wrap the outside of the printer e Cut the tie wraps on the axes 3 in total 8
31. g Creatr Leapfrog e Lower the printbed 50mm clicking on the 10 button for the Z direction 5 times This is necessary because you will be extruding some filament and this needs space e Once the bed is lowered click the extrude button as indicated in the next screenshot to manually extrude filament Your Creatr will start extruding when the extruder is hot enough to extrude the temperature for each filament type is described in section 2 3 We recommend to always extrude some filament before you start a new print When inserting new filament it is necessary to help push the filament through the extruder by hand If you are having difficulties with this please take a look at section 3 1 Leapfrog BV T Manual Leapfrog Creatr Leapfrog e Extrude until the material comes out the nozzle and then remove the printed filament NB Be careful the nozzle of the printer is very hot Leapfrog BV T Manual Leapfrog Creatr Leapfrog Remove old filament Only necessary if there is already filament in your printer and you want to switch to a different filament e Heat the extruder when it is heated to 220 degrees click the Retract button until the filament comes loose at the top of the extruder carriage 1800 0 e Loosen the filament guiding tube and pull the filament from the top of the extruder carriage Now you can remove the
32. he solution in the user manual Appendix A contains the following troubleshootingtrees e cannot connect my printer e Firmware e Calibration e My printer makes a lot of noise e Temperature errors e Extruder jams e Print doesn t stick to the bed e My printer loses connection during print e My bed doesn t heat up e My print looks bad Leapfrog BV Lu e IR Leapfrog a oe ALES eapfrog YES Did you select the correct COM port and Baud rate in the Repetier Host printer settings Did you press the connect button in Repetier Host Do you see a commands waiting message in the Repetier Host manual control tab for longer than 2 minutes NO Does the printer work BV ETE Leapfrog Creatr My printer cannot connect Can you see the printer NO in the control panel YES Did you download NO the arduino software Download the arduino software see par 1 3 user manual Did you install re in stall the arduino software for your Operating System MAC Windows 7 Windows 8 YES Check the firmware trou bleshootingtree 1b for the correct version and ask support to supply you with the correct firmware YES NO Is the printer turned on i Contact support YES with a screenshot Turn the printer on m of your log file We wish you happy printing Le MEALS Vs You can contact support at support lpfrg com Leapfrog BV Th Manual Leapfr
33. he z axis and save the process Leapfrog BV T Manual Leapfrog Creatr Leapfrog G Code Offsets X Axis Y Axis Z Axis Offset 0 00 EH 0 00 190 00 mm e Inz offset box you can fill in the distance that the bed was off A positive value will correct the bed downwards so for the too close situation whereas a negative value will correct the bed upwards so for the too far away situation In the screenshot above the bed will be corrected 190mm downwards e To use the changed process settings you will have to prepare the file you wish to print again with the new process Don t forget to do so Remember that you have not adjusted the printer itself but just given a correction for the offset in the generated g code You can run the print to see if the offset was determined properly If not you can adjust the value in the slic3r settings in small steps of 0 05 0 1mm until you reach the correct distance Don t forget to save the settings and re prepare your file each time you change the settings Leapfrog BV Manual Leapfrog Creatr Leapfrog If you are having connection loss problems and troubleshootingtree 7 My printer loses connection during print has lead you here then it could be that the internal usb cable of your printer is somehow defect and causing connection loss during your print jobs This paragraph will describe how to check this and at least be able to print whilst waiting for a replacem
34. hecking the size of your z axis pulley 3 12 Adjusting the z offset 3 13 Checking the internal usb cable 3 14 Need support Leapfrog BV T Manual Leapfrog Creatr Leapfrog 3 1 Oh oh my filament is not feeding through e This can happen and it is not a big problem The filament is kept on spools which means that the filament is curved into one direction When your filament is not feeding through make sure to feed the filament completely straight and from the top e If your spool stops unwinding no filament is fed to the extruder Retract the filament from the extruder and untangle your filament Insert the filament again and extrude some filament e Please note that the hole where the filament should feed into is very accurately aligned underneath the bearing and drive gear Make sure that you align your filament with this hole Ww ma 4 Correct alignment Wrong alignment ous Leapfrog BV T Leapfrog Manual Leapfrog Creatr 3 2 My object wont stick to the bed Print sticker It is possible to make more than one print on one print sticker However if you print several prints on the same sticker it is possible that your object won t stick on the bed any more In that case please replace your sticker After printing several prints on one sticker you will notice the print sticker will tear rip on some places For smaller parts this is not a problem because you can position t
35. hem on a place that is not damaged However if bigger parts do not stick on your bed always place a new print sticker first Warping When ABS cools down after extrusion it has a certain percentage of shrinkage This means that the object tries to get a bit smaller Resulting in the infamous warping You can reduce warping by changing the Infill or adding Brim o Infill If you are experiencing warping we would advise to decrease the infill if possible Reducing the infill will reduce the shrinkage as you decrease the amount of material that can shrink The infill percentage indicates what percentage of the print will be filled with material In the process tab you can adjust the infill percentage using the slide shown in the next screenshot Infill Percentage ee 0 o Brim In Simplify3D you can also add a brim this feature increases the first layer size by implementing a border around your object when printing the first layer This increases the surface tension and reduces the chance on warpage significantly In the process tab click on Show advanced gt Layer and check the skirt brim box Set the skirt layers to 1 and the skirt offset to 0 00 The width of the brim in layers is set by the amount of skirt outlines Leapfrog BV Manual Leapfrog Creatr Process Mame Processi select Profle Leapog rear ghtexiude imet Remwe Ewwi Auto Configure for Material Auto Configure for Print Quality
36. in the 1 user manual You can contact support at support lpfrg com Leapfrog BV Th Manual Leapfrog Creatr eapfrog 4D Printers My printer makes alot of noise You can contact support to provide you with fans and replacement instructions You can contact support at support lpfrg com Leapfrog BV Manual Leapfrog Creatr Leapfrog Temperature errors ER Leapfrog 3D Printers YES YES b You can contact support at support lpfrg com Leapfrog BV Th Manual Leapfrog Creatr ER My extruder jams Leapfrog 3D Printers You can contact support at support lpfrg com Leapfrog BV Th Manual Leapfrog Creatr ER Print doesn t stick to the bed Leapfrog 4D Printers You can contact support at support lpfrg com Leapfrog BV ER Manual Leapfrog Creatr Leapfrog rK Leapfrog 3D Printers My printer loses connection during print You can contact support at support lpfrg com Leapfrog BV Manual Leapfrog Creatr ee My print bed doesn t heat up Leapfroq Leapfrog 3D Printers You can contact support at support lpfrg com Leapfrog BV Th Manual Leapfrog Creatr ER My print looks bad Leapfrog 3D Printers You will find the settings and instructions at https www lpfrg com support installation Part 2 of 3 Software and configuration Mac You can contact support at
37. milanove w ATmega328 Arduino Diecimila or Duemilanove w ATmegal 68 Board Seri le poort Programmer Arduino Nano w ATmega328 Bootloader branden Arduino Mano w ATmegalb8 Arduino Mega 2560 or Mega ADK Arduino Mega ATmegal280 Arduino Leonardo Arduino Esplora Arduino Micro Arduino Mini w ATmega328 Arduino Mini w ATmegal68 Arduino Ethernet Arduino Fia Arduino BT w ATmega328 Arduino BT w ATmegal68 LilyPad Arduino USB LilyPad Arduine w ATmega328 LilyPad Arduino w ATmegal68 Arduino Pro or Pro Mini 5V 16 MHz w ATmega328 Arduino Pro or Pro Mini SV 16 MHz w ATmegal6s Arduino Pro or Pro Mini 3 3V 8 MHz w ATmega328 Arduino Pro or Pro Mini 3 3V 8 MHz w ATmegal6 Arduino NG or older w ATmegal6 Arduino MG or older w ATmegad Leapfrog BV bx Manual Leapfrog Creatr Leapfrog e Next goto the submenu File gt Open A window will pop up to select a file In this window select the folder you received from support In this folder you will find a file called either Marlin gebruikte ino or Marlin gebruikte pde Open this file In the screenshot example below the file has the name Marlin gebruikte dual M8 ino GS sketch jan22a Arduino 1 0 3 LJ Een ard Jin O SKetcn Openen Zoeken in di Marlin gebruikte dual M8 Y o 5 E ij Naam Gewijzigd op Type cardreader cpp 21 1 2013 14 54 CPP bestand Recente locati
38. og Creatr Leapfrog 3D Printers Firmware YES NO Par 3 12 in the user manual explains how to check the size of your z axis pulley You can contact support at support lpfrg com Leapfrog BV Tea 57 Manual Leapfrog Creatr eapfrog Calibration Ft 7 Leapfrog My extruder prints in My prints are Theheight of my My extruder jams Dual prints print differs from my scrathes my print won t work damaged the air my print model I sticker D ii warps doesnt stick Areboh f to the bed extruders NO DERE scratching the E inier ves bed Are both extruders damages the Is B extruder YES hitting scratching YES prints Hini i the YES the print p Are both T 5 NO extruders mene Does one of printing in the 52 np Do the two o the extruders air dc d i amp eratehine the materials mas printinthealr NO jes pi anes M Ee aH UGPIPO overlap so the material ET pn surface i wont stick AE deg i NO YES NO YES ve A Are the two materials Pee placed apart NO happen from NO w d the start of the printjob Check par 310 in the YES user manual for offset extruders Check par 313 inthe Check par 39 in the Check par 3 6in user manual for the user manual for bed Contact support the user manual for with a screenshot height difference gcc oe of your log file Born mei A extruders Check par 3 11
39. ou can now see all the communication between the printer and your computer This is also the place where errors will be displayed should they occur Leapfrog BV T Leapfrog Manual Leapfrog Creatr 2 3 Preheat Before you start printing it is necessary to preheat your printer The print material needs to be melted and your printbed needs to be warm to make sure the material will stick to your bed Here we will explain you how to do this using the Simplify3D software Select the extruder that you want to print with If you have a Creatr single extruder you should only use Tool 0 right extruder If you have a Creatr dual extruder you can use both extruders In the text box you can enter the temperature to which you want to heat the extruder and the bed The heating process will start after you click set The red light in the software next to the heated element will light up when the heater is On You can stop the heating by clicking Off The indicator will display the temperature that the extruders and the bed are at In the screenshot below the selected extruder heated to 96 degrees Celsius and will continue to heat until it reaches 255 degrees The bed is at 20 degrees Celsius and heating to 80 degrees extruders 2555 Hh x Heatedeed s0 H ly e The extruders should be set to 220 degrees Celcius for ABS 190 degrees for PLA and 200 degrees for PVA The heated bed should be set to 80 degrees for ABS and 6
40. printing the support material the support that is generated results in an easy to break away structure when the print is done If the prints are very small this may become a lot harder The downside of breakaway support is that you will see the marks of the support on the surface of your print as you have broken it away Depending on your demands your object needs a finishing treatment Leapfrog BV T Leapfrog Manual Leapfrog Creatr Soluble support This support type is only accessible for those owning a Creatr Dual extruder as you will need to print with two different materials and extruders The advantage of soluble support is that it dissolves and does not leave any marks on the surface of your print The Creatr supports PLA and PVA as soluble support material PLA is soluble in sodium hydroxide drain cleaner mixed with water and PVA is solvable in ordinary tab water The soluble support material needs to be inserted in the second extruder Warning you should follow the guidelines as listed on the package while using sodium hydroxide After your Creatr is finished printing you need to remove your print including the support material from the bed Place your object together with the support material in the correct solvent for your support material and the support will dissolve High quality or fast printing Now that you have become familiar with the support types available we will tell you the difference between
41. r e On your computer go to Control Panel and select Device Manager t E gt Control Panel All Control Panel Items Adjust your computer s settings Y Action Center Ta Administrative Tools ad AutoPlay E BitLocker Drive Encryption gl Credential Manager ER Date and Time LP Default Programs 4 Device Manager 3 Display e Ease of Access Center d Family Safety ps File History e Goto Ports right click on Unknown Device and select Update Driver Software File Action View Help imi Hr mig sS 4 go Test PC p i Audio inputs and outputs jE Computer Disk drives Display adapters DVD CD ROM drives Human Interface Devices IDE ATA ATAPI controllers E Keyboards d 37 lo Mi n Mice and other pointing devices K Monitors a Network adapters KI Portable Devices Ports COM amp LPT Communications Port COM1 YS USB Serial Port WP USE Serial Por __ YPate Driver Software rn Print queues Disable L3 Processors Uninstall Software devices k 7 VV F F OG Sound video and Scan for hardware changes lt gt Storage controller a Properties TO FO XS O F X Xy tem devices Leapfrog BV bx Manual Leapfrog Creatr Leapfrog e Click on Browse my computer for driver software How do you want to search for driver software Search automatically for updated driver software Windows will search your computer and the Int
42. ring a support ticket Leapfrog BV Manual Leapfrog Creatr Leapfrog e After receiving your new thermistor the following steps will guide you through replacing the thermistor o Make sure that the filament is not loaded in the extruder If it is loaded please retract the filament o Loosen the Allen screw indicated on the picture with an Allen wrench o Loosen the Allen screw holding the heat cartridge in place and slide the heat cartridge out of the heating block o Loosen and remove the broken thermistor Leapfrog BV bx Manual Leapfrog Creatr Leapfrog o Place and tighten the new thermistor in its place and connect the connector o Slide the heat cartridge into place and tighten the Allen screw again o Slide the hot end into the extruder carriage and tighten the other Allen screw again go through the height difference extruder steps to calibrate the height see 3 6 Leapfrog BV T Leapfrog Manual Leapfrog Creatr 3 5 Nozzle seems clogged In most cases the problem can be resolved by increasing the temperature by 10 degrees and extruding Please follow the steps as described below Retract the filament In the machine control panel select the Jog Controls tab and select the extruder of which the nozzle is clogged Make sure that it is heated and click on the retract button to retract the filament Retract until the filament is retracted from the noz
43. rint This manual will describe step by step what to check and how to solve any issues you encounter if your filament stops extruding in the middle of your print Basic checks To start there are a few basic things to check that can make a big difference Laptop screensaver If you connect your laptop to your printer it is important to disable your screensaver If your screensaver is enabled the printer stops printing when the screensaver turns on If you connect your PC to your printer it is not necessary to disable your screensaver Filament spool Check if the filament on the spool is entangled This can make it hard impossible for the driver gear to pull through If this is the case retract the filament as mentioned before Make sure the filament of the spool is free to roll of and reinsert the filament Filament Check if you find scrapings on the filament near the inlet in the electronics cover plate located inside your printer If the inlet is too sharp or the filament is not let in perpendicular pieces of the filament can be cut off Deformation of the filament can result in the driver gear not being able to get grip on the filament or the hot end not heating the filament properly Readjust your filament if necessary Extruders Check if both the extruder fans are working properly If the fans do not work the extruder will not be cooled properly causing large fluctuations in the nozzle temperature which can cause
44. rocess Name text box After doing so you will have to select the profile that you wish to use This will be the Leapfrog Creatr profiles for either the left extruder the right extruder or both extruders depending on your choice of extruder For a single extruder Creatr you should choose the right extruder profile What remains is to choose the filament type that you will be using whether you want to print in medium quality faster than high quality or high quality how much infill you want your print to contain and if you want to use a raft and or support material 0 infill means that you will print your model hollow and 100 infill means that your model will be printed completely solid The raft option will be create some easy to remove lines in the first layers where the print will be created on top of This is good to prevent warping When you are printing a model that requires material to support it in order to print it you will need to apply the support material option We advise to do this at least for prints with an overhang of 45 degrees or more When you are done with your settings click Save to save your settings To adjust your settings afterwards you can double click the process in the processes menu lt FFF Settings mam Process Name i SlectProfie Leapfrog Creat eft extrude Auto Configure for Material Auto Configure for Print Quality PLA ABS 7 PVA Nylon Medium High General Settings
45. t Of course it is possible that you run into something that was not explained in this document Here we explain you what to do in such a case e If you need support click on the Ask Leapfrog button in Repetier Host Leapfrog or go to https www lpfrg com support File Config Temperature Printer Help o 0 B 98 8 7 3 EA Disconnect Load Savelob Runlob EillJob SD Card ToggleLog Show Filament Printer Settings Ask Leapfrog Emergency Stop SDVew TememueQne Obiect Placement Sicer e By clicking on the Ask Leapfrog button in Repetier Host Leapfrog you will be directed to the Leapfrog support page e If you cannot find the solution to your problem at FAQ Knowledgebase or on our Forum you can always ask our support team by creating a ticket Led D frog Home Info 3D Printers Store Support 3D Printers FAQ Installation Forum e Click on the button with the Ticket icon select Existing customer and log in with your account If you do not have an account or if you have forgotten your account please create one Leapfrog BV Manual Leapfrog Creatr In our support ticket system you can again see the Knowledgebase If you have not yet checked if your question is listed here please do so If your question is not to be found in the Knowledgebase create a new ticket by clicking on New ticket o Summarize your question in one sentence and enter this in the Ticket title field
46. t the front side of the extruder behind the fan as indicated on the picture Leapfrog BV Manual Leapfrog Creatr Leapfrog e Remove the heat cartridge by loosening the Allen screw in the heating block e Turn the hot end this will allow you to remove the thermistor e Screw off the old nozzle screw on the new nozzle and tighten its position by mounting the heating block against it uu E e Re attach the hot end in the opposite order as you disassembled it and follow the extruder height calibration as displayed in section 3 6 Leapfrog BV gt E D waa Manual Leapfrog Creatr Leapfrog When there is a height difference between the extruders support material will not properly attach to the printed part or will melt into the printed part This guide will explain how to level both extruders to the same height e Loosening the index bolt The index bolt can be found when you look through the fans on the extruder carriage as indicated on the picture Use an Allen wrench to loosen the index bolts of both extruders It is not necessary to take them out only loosen them e Sliding the hot end down After loosening the index bolts the hot ends will be able to slide up and down Use pliers to move the hot end which is a little bit too high downwards The next step is to home the Z axis by pressing Z home at the Manual control tab The other hot end will start to move upwards At this momen
47. t in time both your hot ends are positioned on the same height Make sure you tighten the index bolts of both extruders to secure their position Leapfrog BV ee Manual Leapfrog Creatr 3 Uploading firmware It is a fairly easy process to upload the firmware onto the Arduino board Please follow the following steps one by one e Make sure your USB cable is connected to your Arduino board aene Onrewareg 2 19031400 72 034221 pia tecti hal et id eget CE wow hg am e The next step is to start the Arduino software go to the tab Extra in the main menu select Serial Port and select the right COM port here indicated as COM6 o sketch jan2Za Ardui ta J A L Bestand Bewerken Sketch Automatische opmaak Ctrl T Sketch archrveren Herstel codering amp herlaad sketch jan22a Seri amp le monitor Ctrl Shift M Board Seri le poort Programmer Bootloader branden Leapfrog BV A Manual Leapfrog Creatr Leapfrog e Select the Arduino Mega 2560 board by going to the tab Extra in the main menu select Board and select Arduino Mega 2560 or Mega ADK sketch_jan22a Arduino 1 0 3 Bestand Bewerken Sketch Extra Help Automatische opmaak Ctrl T Sketch archiveren Herstel codering amp herlaad sketch jan22a Sen le monitor Ctrl Shiftt M Arduino Uno Arduino Due
48. te of the Creatr This can easily be done by loosening the four screws in the corners of the plate Please note that you should first remove both the power and the usb cable to prevent damage to the electronics The plate is still attached to the printer at the power and usb entrance below and the drag chain at the top so you can t remove it entirely but this will not be necessary to measure the pulley e Now that you have removed the backplate the pulley has become visible and you will be able to measure the diameter as indicated in the picture below Please contact support with the measured diameter so they can provide you with the correct firmware for your printer Leapfrog BV T Manual Leapfrog Creatr Leapfrog 3 12 Adjusting the z offset In order to make good prints it is of great importance that the bed is at the right height from the nozzle If the nozzle is touching the print bed no filament can be extruded and the sticker will be damaged Whereas a distance that is too large between the nozzle and the bed will result in curling filament extrusion a bad looking result and poor adhesion to the print bed The distance is correct when you can only just move a piece of paper with slight friction between the nozzle tip and the bed This section will explain how to check and adjust the z offset using the slic3r settings e Start by homing the printer by using the home button in the jog controls tab The printer is now in i
49. ted the distance rebuild the extruder carriage as it was and try to extrude 10 mm of filament and afterwards retract your filament again to check if the filament is severely deformed or has no marks at all If it does not display any marks insert the filament again and try to extrude a couple of centimetres to make sure the extruder is working properly Un used Extruded Too faraway Correct Too close Figure Sketch of the filament for three types of distances between the driver gear and the bearing Left shows when they are too far apart The middle shows the correct distance and the right sketch displays the filament when the distance is too small Leapfrog BV e Leapfroq Manual Leapfrog Creatr Always first check all the wiring Most of the times it comes down to a loose connector always add some pressure to the connectors to make sure that they are thoroughly connected You will need to unwind the plastic cover that covers the wires to check this Don t forget to cover it again Correct Connected Wrong Disconnected e Lower your bed and take a look underneath the extruder carriage This way you can make sure both the heat cartridge and thermistor are properly connected e If both of the previous steps are checked properly we will have to conclude that the thermistor has failed In this case we should place a new thermistor Please contact our support department via support lpfrg com by ente
50. ting e The print sticker or Kapton tape is used to make sure the print material will stick to the print bed Without a print sticker or Kapton tape adhesion is not possible First check if the print sticker or Kapton tape can be re used You can re use them until there is no space left that is undamaged We advise you to position your object on an undamaged part of the printing sticker tape Example of a sticker that needs replacing Leapfrog BV T Manual Leapfrog Creatr Leapfrog e If the print sticker is damaged and you cannot position your print on an undamaged spot remove the sticker by lifting one of the corners of the sticker and peeling it off If you remove it too quickly the sticker is more likely to tear e Remove the sticker glue by applying sticker remover or glass cleaner on the printbed Be sure to remove the whole sticker and all of the sticker glue so you will end up with a clean glass plate If residue is left behind this could affect your print quality Leapfrog BV T Leapfroq Manual Leapfrog Creatr e Apply the new sticker by placing the sticker on your print bed If you are satisfied with the position take of the small part of the sticker Use a plastic card to apply the sticker work from the inside to the outside and avoid air bubbles Take off the big part slowly and use a plastic card to apply the sticker work from the inside to the outside Kapton tape e
51. ts O point for the z axis Now you can see whether the bed is too close or too far away from the nozzle Because the z axis induction sensor prevents the bed from going up further than this point there are two different ways to determine the offset One for the situation where the bed is too far away and one for the case where the bed is touching the nozzle e When the bed is touching the nozzle it is fairly easy to determine the offset When the printer is homed you can move the bed down in small steps with the jog controls until you can only just move a piece of paper between the two with slight friction Then you can read the offset from the machine control panel in the right top corner In the screenshot below the distance indicated is 190 00 mm Position Readout X TETIT C zerox Y idi Ezer Z HH C zeroz e When the bed is too far away from the nozzle you are unable to move the bed further up with the manual control tab because of the sensor Therefore you will have to use a different way to determine the distance The easiest way would be to use something of a known thickness for example a thin metal plate and use this to estimate the distance e Now that the distance has been determined you will have to insert the value in the process settings In Simplify3D go to the process Click on Show advanced and select the G code tab In this tab you can fill in the offsets for all the axes Now fill in the offset as shown in the for t
52. ve the old setpoint and add the new setpoint to the increased temperature Don t forget to save the changed process DOR E Right Extruder Temperature Left Erde reweatve enter S 0 Heated Bed p Temperature Controller Type Extruder Heated build platform Relay Temperature Between Each Layer Loop Wait for temperature controller to stabilize before beginning build Per Layer Temperature Setpoint Temperature 190 Layer Number 1 E Temperature 200 E E Add Temperature Controller Remove Temperature Controller Leapfrog BV T Manual Leapfrog Creatr Leapfrog e Print without using the filament guiding tubes The filament guiding tubes through which the filament is fed into the extruder can cause drag that makes it hard for the driver gear to pull the filament through Printing without the use of the tubes will reduce this drag So remove the filament spool holders from the bottom of your Creatr and place this holder on the top plate of your Creatr Feed the filament directly from the spool into the extruder and try to see if this improves the print result Leapfrog BV T Manual Leapfrog Creatr Leapfrog e Changing the distance between the bearing and the driver gear If none of the above has proven to be a solution you can check if the distance between the driver gear and the bearing of the extruder is set correctly In order to determine this you will have to extrude some filament an
53. xis individually or use the Home all button to home all three axes at once The physical home position of the printer is when the extruder carriage is in the front left corner and the bed in its most upward position N B When you connect your printer and want to use the jog controls the first thing to do should always be to home all the axes This is to avoid any possible damage to the printer You can adjust the speeds of the jog control operations in the Speed textboxes Please note that these speed settings apply only to the jog control movements and not to the print job movements The movement speeds of a print job are contained in the g code Leapfrog BV LX A Am Leapfrog Manual Leapfrog Creatr In this section of the manual we will explain you how you can load new filament and how to switch between filaments that you already have loaded e Place your filament on the turntable in your Creatr such that the filament is rolled of Straight in to the entry hole in the electronics cover Disconnect the filament guiding tubes from your extruder by pushing on the blue circle and pulling the filament tube upwards at the same time H The filament tube positioned Push the blue ring down While pushing the ring downwards pull in the extruder the filament tube upwards e Feed the filament through the holes until it reaches the drive gear of the extruder Leapfrog BV T Manual Leapfro
54. you can see which COM port you need to select the number is displayed after the driver installation and verify that the baud rate is set to 115200 omm m 0 Mo Leapfrog BV T Manual Leapfrog Creatr Leapfrog e By clicking the connect button as indicated in the next screenshot you can connect the printer It will turn green when you are connected to the printer It may take a few seconds for the printer to connect Wf Verbose e Now all that remains is to connect the printer to the power by connecting the power cable to the printer and turning it on using the socket switch on the back WARNING ALWAYS MAKE SURE THAT THE FIRST MOVEMENT YOU PERFORM WHEN THE CREATR IS RE CONNECTED IS HOMING ALL THE AXES OTHERWISE YOU CAN DAMAGE THE PRINTER Leapfrog BV ER Manual Leapfrog Creatr Leapfrog The following steps are general steps you need to follow when making a 3D print with your Creatr Please follow each step to make sure you will be able to print a beautiful print This section contains the following 2 1 Print sticker and kapton tape o How to check the sticker and how to replace it if necessary 2 2 Connection o How to connect the printer to the computer using the software 2 3 Preheat o How to preheat your printer so you are able to print 2 4 Manually controlling your printer o How to control the movements of your printer manually 2 5 Filament o How to insert or change your filament and extru
55. zle and remove the filament in an upward direction from the extruder Increase the extruder temperature by 10 degrees Increase the temperature of the extruder that is clogged right or left extruder as shown in the field below and click On to set the extruder to the new temperature Active Toolhead Tool 0 right e 0 i amm ann veces oF Die e J 9 Snip of the used filament and make sure the cut is under a sharp angle to the direction of the filament Leapfrog BV e Manual Leapfrog Creatr Leapfrog e Insert the filament in the extruder e Extrude the new strand of filament Make sure the extruder is heated and extrude until filament is extruded through the nozzle If the previous step was not the solution you will need to replace the nozzle with a new nozzle Please follow the below mentioned steps carefully e Heat the extruder that is clogged to 230 degrees e Take your wrench and loosen the nozzle do not take it off completely Be careful the extruder is very hot Do not touch it with your bare hands Leapfrog BV ee Leapfrog Manual Leapfrog Creatr e Let the extruder cool off you can monitor the temperature of the extruder in Simplify3D as shown in the next screenshot Do not check the temperature of the nozzle with your bare hands duni BY cui Remove the hot end from the extruder carriage by loosening the Allen screw that is located a

Manual Leapfrog Creatr

Contents

Download Pdf Manuals

Related Search

Related Contents