Installation Instructions
Contents
1. Allen screw using the provided Allen wrench Figure 10 Install 2 1 2 extension portion of the speaker mount to the wall plate Secure the setscrew to hold the extension in place with the weight of the speaker attached plate and into the alligator Wall and Ceiling Applications 1 Using the wall plate as a template mark a hole positions on the mounting surface NOTE In wall mounting applications position mounting holes in a vertical pattem 2 Drill holes in the solid concrete or hollow block using a 5 16 masonry bit Once the holes are drilled insert the 12 14 Alligator anchors Figure 9 into the holes making sure the anchor is flush with the surface of the wall Figure 9 3 With the wall anchors in place mount the wall plate using the 12 x 1 3 4 self tapping screws Figure 9 Low Profite Mounting Speaker Mounting WO Tighten the Allen screw using the provided Alten wrench Figure 11 Install the low profile portion of the speaker mount to the wall plate or 2 1 2 extension Secure the setscrew to hold the extension in place with the weight of the speaker attached Post Style Speaker Plate 2 Hole Speaker Plate Figure 12 Install the speaker with the speaker post or 2 hole plate attached Secure the setscrew to hold the extension in place with the weight of the speaker attached2. Installation Instructions a MS xomm Machine See OF Saag 40314 Self Tapping Screw 2ca M5 x 20mm Machine Screw 2ea IMPORTANT wp 8 32 x 5 8 Machine Screw 2ea 12 x 3 4 Self Tapping Screw 2ea Please read the instruction sheet prior to installation This speaker mount was designed solely for the mounting of small speakers weighing less than 10lbs Premier Mounts is not responsible for damage that may occur if speakers weighing more than 10lbs are used 1 4 20 x 1 2 Machine Screw 4ea 12 x 1 3 4 Self Tapping Screw 2ea K 12 14 Alligator Plastic Anchor M5 x 1 8 Plastic Washer 2ea M4 x 8mm Flat Head Machine Screw 2ea NOTE The user will have to determine which type of configuration will work best with the hardware that was purchased If the included hardware does not fit the application the appropriate hardware will have to be purchased 8 32 Round Key Hole Nut Zea Single Hole Mounting 1 Most satellite speakers will require the use of the M5 x 20mm machine screw used in combination with the M5 x 1 8 plastic washer The plastic E M5 x 20mm Machine Screw washer is used as a spacer between the threaded insert and the post Figure 1 E NOTE It is critical the M5 plastic washer is used correctly E 2 Once the proper configuration is determined secure the post to the speaker M5 x 1 8 i Plastic Washer 3 Some speakers use the smaller M4 x 8mm hardware which is inserted into the
3. off center hole on the M5 x 1 8 mounting post Figure 2 Plastic Washer Speaker Back 4 Check the size of the hole and make sure the 8 32 x 5 8 machine screw the 1 4 20 x 1 2 machine screw the 1 4 20 x 7 8 or the M5 x 20mm fits inside Figure 3 M4 x Bm Flat Head f 5 When the correct size is determined place the screw through Figure 1 Machine Screw the speaker post and attach to the tear of the speaker enclosure 3 8 32 x 5 8 NOTE If the screw does not tighten properly use the M5 x 1 8 E Machine Screw i erase abba plastic washer to tighten it up a Figure 3 Figure 2 M5 x 1 8 Plastic Washer Keyhole 8 wees X Key Hole Mounting 8 32 x 5 8 7 1f your speaker has a factory key hole design you will use the see Round key Machine Scie 8 32 x 5 8 machine screws in combination with the key hole nut ole Nut 8 Loosely pre assemble the mounting post with the 8 32 x 5 8 Figure 4 machine screw and key hole nut Figure 4 NOTE Be sure the key hole nut is installed with the knurled rough edge toward the post 9 Engage the key hole nut into the key hole slot as shown 10 Put tension on the assembly by gently pulling back on the speaker mount post while tightening the 8 32 x 5 8 machine screw Figure 4 11 The key hole nut will engage on the housing in the key hole slot 12 If the post does not tighten securely against the housing it will be necessary to use the M5
4. tions A int ti PAPI ok oy on mounting surface Figure 7 NOTE Inwall mounting applications position mounting holes in a vertical pattern Figure 7 3 Drill holes through the drywall and into the wood stud using a 1 8 drill bit These holes should be drilled 1 7 8 deep Figure 7 4 After the holes are drilled mount the wall plate using the 12 x 1 3 4 self tapping screws Pre Drill 2 4 5 16 Holes sur Toing Screw 4ea Figure 8 DRYWALL SURFACE _ 1 Locate the best mounting location in the ceiling or wall Mararar a mate ond tate Ihe aligator Using the wall plate as a template mark the hole positions pum O anchor on the mounting surface NOTE In wall mounting applications position mounting holes Insert Alligator Anchor in a vertical pattern l 2 Drill holes in the drywall using a 5 16 drill bit Figure 8 3 Once the holes are drilled insert the alligator anchor into the holes Make sure the anchor is flush with the wall and or ceiling surface Figure 8 4 With the anchors in place mount the wall plates using the 12 x 1 3 4 self tapping screws Figure 8 aranna raran CONCRETE SURFACE _ Self Tapping Insert Alligator Anchor Screw 4ea Insert screw through wall anchor Use hammer to tap i e anchor into place Figure 9 Extension Mounting Ceiling and or Shelf Applications Do Not Use went Extension In Wall Mounted Applications Tighten the
5. x 1 8 plastic washer as a spacer under the head of the 8 32 x 5 8 machine screw Figure 4 2 4 Hole Mounting 13 Find the best mounting configuration that matches your speaker enclosure Four hole speaker mount patterns can be accomodated by positioning the speaker plate diagonally Figure 5 14 Using the 1 4 20 x 1 2 machine screws install the speaker plate and secure the speaker enclosure Figure 5 Saab 1 4 20 x 1 2 Machine Screw 2ea ame 2 Hote Orientation Figure 5 Speaker Back 12 x 3 4 i Self Tapping Screw 4ea Speaker Back Figure 6 Self Tapped Mounting 15 Locate the optimum location for the mounting plate and use it as a template to mark the drilling locations NOTE Do not drill or screw into the speaker where you could possibly damage the internal components 16 Drill the pilot hole s using a 1 8 drill bit This hole s should not be drilled more than 1 2 depth Figure 6 MOUNTING TO THE WALL OR CEILING a The mounting hardware for three different surface applications is supplied You will need to determine what style hardware will work best with your mounting surface Always use caution when drilling into a wall or ceiling Make sure to avoid all electrical and water lines WOOD SURFACE 1 Using a stud finder locate the wood stud or framing member NOTE Always mount the speakers in the center of a stud 2 Using the wall plate as a template mark hole posi
Download Pdf Manuals
Related Search