Home

User Manual

image

Contents

1. read the Current time or Alarm time with alarm on off status at night To use the feature 1 Press SNOOZE to turn on the projection for 5 seconds The current time with alarm on off status Pe on or off will be projected onto the surface the lens is facing 2 To change to view the preset alarm time with its on off status press SNOOZE when projection is already on 3 Adjust the projected image as below a tn Y Da SUCd aa pa Lio Lt Current Time amp Alarm Time amp Alarm on off Status Alarm on off Status Projector Features Feature Effect Instructions Adjustable Rotates the Projector Tilt swivel projection to alter projection 180 the direction of projection FOCUS Knob Focuses projection Rotate to focus projection C IMAGE ROTATION knob convenient Rotates projection Rotation of projection allows user to place clock in 180 Horizontally flips ROTATION button Flips an image to maintain the projection 180 an upright position Note Make sure the PROJECTION ON switch is switched to the back HOW TO USE THE PROJECTOR WITH POWER ADAPTER RM868P RM868PU comes with an AC power adapter Use of the AC power adapter is required for continuous projection Once the power adapter is in place you can select to turn on the projector for longer time such as throughout the night by sliding the PROJECTION ON switch on To turn off the projector
2. LARM This unit is equipped with a daily alarm function To set the alarm 1 Press ALARM to change both the digital and analog display to the alarm time display mode 2 Press and hold ALARM for 2 seconds 3 Use A W to enter the hours The hand of hour on the analog display will be adjusted simultaneously 4 Press ALARM HOW TO USE THE DAILY ALARM An alarm will go off for 2 minutes in two step crescendo patterns if undisturbed The Pp icon will flash the back light and the clock projection will be activated for 5 seconds To mute the alarm press any key Pressing SNOOZE will activate the snooze function SNOOZE FUNCTION When the snooze function is activated the alarm will be muted temporarily and set off again after 8 minutes To disable the snooze function press ALARM SECTION3 NOTES ON BACKLIGHT ADDITIONALINFORMATION The EL panel that provides illumination will lose power after extensive usage The unit may emit an audible sound whenever the display is illuminated by the EL backlight This is due to vibration of the THE RESET BUTTON EL panel used for illumination and does not indicate The RESET button is used to enhance synchronization of signals malfunction of the unit after battery replacement or when the unit is operating in an unfavorable way or malfunctioning Use a blunt stylus to hold down the button All settings will return to their default
3. RADIO CONTROLLED PROJECTION CLOCK MODELNO RM868P RM868PU USER S MANUAL SECTION 1 INTRODUCTION Congratulations on your purchasing the RM868P Radio controlled projection Clock The Projection Clock is a compact easy to handle device The RM868P the Central Europe model is designed to automatically synchronize its current time and date when brought within an approximate 1500km radius of the radio signal generated from Frankfurt Germany DCF77 The RM868PU the UK model will do the same when brought within range with MSF in the United Kingdom The Projection Clock also comes with favorable features such as clock projection multilingual day of the week display back light dual analog and digital displays of time and daily alarm with 8 minute snooze function NHL A od OO 8 DISPLAY BUTTONS A B DIGITAL CLOCK DISPLAY ANALOG CLOCK DISPLAY CONTROL BUTTONS Cc D MODE SET BUTTON Changes the display mode or holds to enter the setting routine ALARM BUTTON Manipulates the daily alarm function A AND W BUTTONS Change the value of a setting SNOOZE BUTTON Activates the snooze function or turns on the back light and clock projection RESET BUTTON Returns all settings t
4. ctive if used for its intended use and that the following standard s has been applied Electromagnetic compatibility Article 3 1 b of the R amp TTE Directive ETS 300 683 1997 Efficient use of the radio frequency spectrum Article 3 2 of the R amp TTE Directive Applied standards Applied standards EN300 220 1 1997 INTENDED USE OF THE DEVICE CAUTION The content of this manual is subject to change without further notice Due to printing limitation the displays shown in this manual may differ from the actual display The contents of this manual may not be reproduced without the permission of the manufacturer
5. gco hs An Hbnotul aur areq euopeuiau 40 9 8 7 8 5 A 39 24 O A 2 48 A 45 46 47 1B 49 HO 41142 101 Enter the clock format using A W You can select 12 hour or 24 hour display 4 Press MODE SET 5 Enter the hours using A W The hand of hour on the analog display will be adjusted simultaneously 6 Press MODE SET 7 Enter the minutes using A W The hand of minutes on the analog display will be adjusted simultaneously 8 Press MODE SET Follow the same pattern to set the year date format month day or day month month day and display language English E German D French F Italian I or Spanish S for day of the week Day of the week Language Monday Tuesday Wed Thursday Friday Saturday Sunday English f Ti German L French r 5 Use A W to enter the minutes The hand of minutes on the analog display will be adjusted simultaneously 6 Press ALARM The alarm will be automatically activated The Pe icon will appear To deactivate the alarm press A W when the alarm time is displayed Ttalian LI Spanish 10 Press MODE to save the changes and exit If changes are made during the process the seconds will reset and start from zero The unit will also save all changes and return to normal display automatically after the unit has been left idle for a minute ABOUT THE A
6. o default values PROJECTION ON BUTTON Used with power adapter to enable continuous projection IMAGE ROTATION KNOB 90 left or right image rotation 180 ROTATION BUTTON Flips the projected image horizontally FOCUS KNOB Adjusts the focus of clock projection L 3VDCJACK For AC power adapter installation M WALL MOUNT HOLE N PROJECTOR POWER This unit can be operated by batteries or AC power alone as well as both together Battery Installation Remove the battery compartment door 2 Insert two AA sized UM 3 1 5V batteries as shown 3 4 Replace the battery compartment door Press RESET To install the adapter 1 Insert adapter into jack at the bottom of the unit 2 Plug the adapter into an electrical wall outlet g g To O OF O Oj Note Make sure the voltage is correct When the power level of the installed batteries is low or when only AC adapter is connected the low battery indicator 4 will light up In these cases replace or install with new batteries HOW TO ACTIVATE THE BACK LIGHT Press SNOOZE to turn on the back light for 5 seconds HOW TO USE THE CLOCK PROJECTION The clock projection makes it easier for you to
7. slide the switch back If you have press SNOOZE to change the projected image to Alarm time with its on off status when projection is on please note that the projected image will return to Current time with Alarm on off status automatically after 10 seconds Note that this switch can only be used with the power adapter installed For momentary projection use the SNOOZE SECTION 2 THE CALENDAR CLOCK DIGITAL amp ANALOG DISPLAY MODES Press MODE SET to display the following in sequence Digital Analog 1 Current Time with Second Calendar 2 Current Time with Weekday a AVA W Sig 2 zone time 4 2 zone time with Weekday y Lei a A ei ala PSB e CID St ne D Cot 24 zone time Calendar To display the alarm clock and details press ALARM The daily alarm time will appear in the lower line of the digital display as well as the analog display ABOUT RADIO RECEPTION When the unit is within range of its respective radio signals its radio control mechanism will override all manual settings unless radio reception is being deactivated After battery installation the unit will start to search for radio signal automatically When it is receiving radio signal the radio reception icon will start to blink A complete reception generally takes about 2 to 10 minutes depending on the strength of the radio signal After that the periodical scanning will onl
8. values PRECAUTIONS This unit is engineered to give you years of satisfactory service if handled carefully WALL MOUNT OR TABLE STANDING ee 1 Do not immerse the unit in water This unit is designed specially so that you can adjust the angles of 2 the different parts to facilitate table standing or wall mounting Do not clean the unit with abrasive or corrosive materials 3 Do not subject the unit to snow or excessive force shock dust temperature or humidity Wall Mount Table Stand 4 Do not tamper with the unit s internal components 5 Do not mix new and old batteries or batteries of different specifications SPECIFICATIONS Radio Control Auto Synchronization of current time and date Calendar Day of Week in English German Franch Italian Spanish Month Day or Day Month format Clock Time 12 24 hour format Accuracy 0 5 second day when RF is disabled Alarm 2 minute crescendo alarm with 8 minute snooze function Power 2 pes of UM 3 or AA size batteries Power Adapter 3VDC Weight 200 g without battery Dimensions mm 135x 152x26mm HxWxD NOTE ON COMPLIANCE Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment R amp TTE Compliance Note This device complies with the essential requirements of Article 3 of the R amp TTE 1999 5 EC Dire
9. y take a few seconds The antenna icon indicates the quality of reception WEAK NORECEPTION RECEIVING When the ae is complete the radio reception icon will appear as and the received radio controlled time will be displayed adeo dingly Interference Reception can be affected by a number of factors For best reception place the device away from metal objects and electrical appliances Note Interference from sources such as TV sets can affect the signal If after batteries have been inserted for ten minutes the signal is not received then set the time manually see section How To Set The Clock amp Calendar Manually HOW TO ENABLE OR DISABLE AUTO RECEPTION If you wish to disable the auto reception of radio signal feature while the unit is within range press and hold W button for 2 seconds The radio reception icon on the will disappear and the unit will NOT respond to radio signals To enable the feature again press and hold A for 2 seconds The radio reception icon will be shown again and it will start blinking to initiate reception automatically HOW TO SET THE CLOCK amp CALENDAR MANUALLY 1 Press and hold MODE SET for 2 seconds 2 Enter the 2 time zone offset hour using A W You can select between 23 and 23 hours Hold down either button to rapidly increase or decrease the value Press MODE SET eur erq Jeuonewiayu Vangouv Ban Franci

Download Pdf Manuals

image

Related Search

Related Contents

  Eug.Le Bossé $CA> l IMS Ile Insurance Co  PB Hylo-GEL Bene 32.2551.indd  photocatalyst mosquito trap - 3w piège à moustiques  Aérogénérateur Bornay 6000  Bullard TI Commander™ Thermal Imager User Manual  Aide Pierre  région - Université de Sherbrooke  M07243 Tetra Italian Manual Issue 7 080108.qxp    

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.