FLUSH MOTOR CONTROL BOARD FOR ROLLER SHUTTER ANKPA
Contents
1. on the control card is wish to register remove your finger off the button In this mode The button of the first remote control unit informing you that it awaits you to press a proper Registering the remote control seconds registered with the system determines the Once the control card enters the learning mode you must press a proper button of the remote control card within 5 Press the very button of the remote control unit that you Learning procedure When the control card is programmed for your remote control the middle LED will rapidly flash on and off operating channel of the control card You may only program the same button of other remote control units that you register later on Failure of the control card to learn your remote control unit can be caused by one of the following reasons m Pressing a wrong button of the remote unit 7 The remote unit that you are trying to register might have a RECEIVE CODE different from those you had registered before Your remote units MUST be programmed by LCD CODER device so as to possess the same receive code n You might run out of memory of the control card which can register up to a maximum of 40 remote units m Control card might have already registered a remote unit from a different manufacturer 7 Your remote unit might be produced by a different manufacturer or you might be trying to allocate a wrong channe2. motor stops the LED goes off as well Operating the Motor in the closing direction Depress and hold the bottommost button for about 1 sec Your motor will be started via terminals 1 and 2 and the LED nearthe button will light This output will be active for about 120 Afterwards the output will be PS Should your motor rotate in the unintended direction swap the cables you connected to terminals 1 and 3 REGISTERING THE REMOTE CONTROL UNIT WITH THE CONTROL CARD To register the remote control unit go through the following steps 1 If your device is off connect 220V mains power All the LEDs will turn on and off in sequence If there is no remote control unit registered with the system the middle LED will flash on and off 3 times as the control card turns on If there is already a remote control unit registered the middle LED will flash on and off once 3 After the control unit is on carry out the following steps KONTAL ELEKTRONIK FLUSH MOTOR CONTROL BOARD FOR ROLLER SHUTTERS ANKPA 17 Entering the learning mode until the UP on in remote control registration mode and you can the upper and lower LEDs will switch on and off button of the remote control unit that you want to register Learning mode is active for about 5 seconds On expiry of this period the control card exits this mode Depress the middle button for 5 seconds and DOWN LEDs are both When these LEDs are
3. FLUSH MOTOR CONTROL BOARD FOR ROLLER SHUTTER ANKPA USER MANUAL V 1 0 www kontal com tr JANUARY 2013 AREA OF USE Flush Motor Control Card is particularly intended to control 3 terminal 2 way motors with or without command Such motors have three terminals for common forward and reverse rotation Motor control unit ANKPA which is easy to mount and has an aesthetic look will be a significant solution in such projects Detailed information related to the product is provided below MAKE SURE THE UNIT IS NOT POWERED DURING INSTALLATION TECHNICAL SPECIFICATIONS Product name ANKPA Dimensions Height 76 mm Depth 49 mm Width 74 5 mm Operating voltage 220 230 VAC 50 60 Hz No load current 6 5 mA Maximum contact pull time 120 sec Operating temperature 20 C 55 C Contact type 220V AC output Maximum contact current rating 250V AC 5A Remote control unit 433 92 MHz Rolan Series a maximum of 40 units Flush mounting LED warning system fuse protection global control Additional features of all motors in the area with All Up All Down function Sekil 2 Motor and power Sekil 3 Mounting the wall fixture on the cables inside the junction box junction box Sekil 5 Inserting the body of the control card into the junction box after cable termination Sekil 4 Connecting the cables from the junction box on the control card terminal block Sekil 6 Fitting the external frame on the body of t
4. he control card Sekil 8 Detaching the control card main body from the metal frame of the junction box Sekil 7 Positioning the external frame over the control card body KONTAL ELEKTRONIK FLUSH MOTOR CONTROL BOARD FOR ROLLER SHUTTERS ANKPA CA INSTALLATION MOTOR HA N AAA SS MT GROUND 220 230 VAC 50 60 Hz Connecting the roller shutter motor to the control card CONTROLLING THE MOTOR WITH CONTROL CARD BUTTONS Your device starts operation after motor and power connections are made The middle LED will flash on and off for 5 6 seconds This indicates that your device is operating normally Operating the Motor in the opening direction Depress and hold the topmost button for about Stopping the Motor Depress the middle button for about 1 1 sec Your motor will be started via terminals 2 and 3 and the LED near the button will light This output will be active for about 120 sec Afterwards the output will be Output via will be deactivated and the LED next to the button will flash briefly and the motor will be stopped deactivated You can override the 120 sec timer and deactivate the motor output by depressing the middle button When the motor stops the LED goes off as well terminals 1 2 ve 3 Sec deactivated You can override the 120 sec timer and deactivate the motor output by depressing the middle button When the
5. l After registration you can run your motor in forward reverse directions or stop it pressing the remote control button you programmed during registration Forward rotation opens the roller shutters reverse rotation shuts them UNREGISTERING THE REMOTE CONTROL UNITS Remote control unit registration can be removed from the control card memory in two ways Method 1 Y Remove the power amp With the middle button still depressed wait until the middle LED starts flashing rapidly All remote controls are removed from memory The middle LED will become on Reconnect the Keep pressing the power middle button until Step 5 Method 2 Keep the buttons pressed until the middle LED rapidly flashes on and off 5 sec approximately This will unregister all remote units on control card memory i On entering the learning mode press the upper and lower buttons simultaneously While the card is working press the middle button until the upper and lower LEDs turn on 5 sec approximately forcing and keep your fingers on them until you the control card into learning mode are done with Step 3 The middle LED will become on KONTAL ELEKTRONIK FLUSH MOTOR CONTROL BOARD FOR ROLLER SHUTTERS ANKPA ET
Download Pdf Manuals
Related Search